Engineering Commons^™

Niel Calculations For High-Energy Heavy Ions, John W. Wilson, I. Jun, M. A. Xapsos, E. A. Burke, F. F. Badavi, L. W. Townsend

Nuclear Engineering and Radiation Science Faculty Research & Creative Works

Calculations of NIEL are reported for heavy ions prominent in the space environment for energies ranging from 200 MeV per nucleon to 2 GeV per nucleon.

Extending Asterism Decoding To Qam And Its Complexity In Rician Fading Mimo Systems, Phillip Conder, Tadeusz A. Wysocki

Department of Electrical and Computer Engineering: Faculty Publications (to 2015)

The area of Multiple Input Multiple Output (MIMO) communications systems has received enormous attention recently as they can provide a roughly linear increase in data rate by using Multiple Transmit and Receive antennas. The optimal detection strategy for a MIMO receiver is to perform a Maximum-Likelihood (ML) search over all possible transmitted symbol combinations has an exponential complexity when the constellation size of number of transmit antennas increase. A number of sub-optimal decoders, such as VBLAST, provide linear decoding only where the number of receive antennas is at least equal to the number of transmit antennas.

Certain Asterism decoding described …

Advanced Relation Model For Genome Sequence Visualization (Arm 4 Gsv): Exploratory Visualization Examples, Brian J. D'Auriol, Kavitha Tupelly

Departmental Technical Reports (CS)

The Advanced Relation Model for Genome Sequence Visualization (ARM 4 GSV) is proposed in this paper. This model is adapted from an earlier visualization model which has been applied to the visualization of computer programs. A review of the fundamental model components of the earlier visualization model is given. Enhancements so as to make it applicable in genome visualization are discussed. As part of these enhancements, a relational characterization of genome sequences in terms of bases, codons, and patterns such as close inversions is developed and described. An adapted form of the Conceptual Crown Visualization (CCV) model, a part of …

Synthesis And Characterization Of Starch Acetates With High Substitution, Yixiang Xu, Vesselin Miladinov, Milford A. Hanna

Industrial Agricultural Products Center: Publications and Information

Acetylation of high-amylose (70%) maize starch to high degree of substitution (DS) was studied by reacting starch with acetic anhydride using 50% aqueous NaOH as the catalyst. DS increased with increasing reaction times and increasing ratios of acetic anhydride to starch. Reaction efficiency (RE) increased with longer reaction times and decreased with increases in the ratios of acetic anhydride to starch for extended reaction times. Increasing the amount of NaOH increased both DS and RE. A series of starch acetates with DS values of 0.57-2.23 were prepared and their crystalline structures, chemical structures, thermal stability, and morphological properties were investigated. …

Comparison Of Sampling Methods For Flatness Evaluation Using Cmm, Ashish Singhal

All-Inclusive List of Electronic Theses and Dissertations

Efficient part feature verification using Coordinate Measuring Machine (CMM) requires efficient sample point selection as well as accurate zone fitting. This work deals with flatness tolerance evaluation and the Least- Square (LS) technique is used to compute tolerance zone. In regard to the sampling strategy there are several methods commonly employed in Coordinate Measuring Machine inspection literature. The appropriate method is selected according to the accuracy requirement, the geometry features of the work piece, and the condition of the machine producing the work piece. This research focuses on the five sampling methods: Hammersley sequence sampling, Halton-Zaremba sequence sampling, Random sampling, …

2004 Fall Student Seminar, Matt Dekam, Chris Wiesehan, Jason Flietstra, Jeremy Hanson, Brian Katerberg, Kevin Palmer, Aaron Svacha, Aaron Buys, Josh Blocker, Matt Vredevoogd, Andrew Huisjen, Thomas Totoe, Andy Vandermoren, Chris Vanroekel, Terry Austen, Kristin De Groot, Matt Ooms, Andy Van Noord, Kurt Koubal, Dan Kuiper, Andy Wermel, Ryan Dewall, Eddie Lucas, Dawn Svenkeson

ENGR 333

File for student presentation, given by students in the Fall 2004 class of ENGR333.

Using Simulation Techniques To Evaluate Group Technology Heuristics: A Recommended Methodology For Comparison And Optimization, Ashley Nolen Akerman

Masters Theses

Machine cell formation is an important issue in industrial and manufacturing engineering. Properly assigned machine cells can improve manufacturing system efficiencies and decrease unnecessary material movement. To address the need for proper cell formation techniques a myriad of heuristics have been created that attempt to optimize the grouping of machines. Further, much industrial engineering research has been conducted on the application of simulation technology to manufacturing system evaluation.

The purpose of this thesis is to investigate the combination of traditional machine grouping heuristics with simulation technology and to create a generalized meta-model based upon this evaluation. This investigation analyzes the …

An Assessment Of In-Situ Frp Shear And Flexural Strengthening Of Reinforced Concrete Joists, Annaiah Raghu, John J. Myers, Antonio Nanni

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This study examines the in-situ shear performance and modes of failure of reinforced concrete (RC) T-beams (joists) strengthened with externally bonded carbon fiber reinforced polymer (CFRP) sheets. the experimental program consisted of testing a series of nine structural components at the Malcom Bliss Hospital, in St. Louis, Missouri. the members were tested to validate the different systems and techniques of strengthening. in particular, this paper covers cases of U-Wraps with and without end-anchors. the experimental results clearly indicate the contribution of externally bonded CFRP sheets in increasing the shear capacity of the system. the experimental and theoretical shear strength of …

Acuta Enews December 2004, Vol. 33, No. 12

ACUTA Newsletters

ln This lssue

From the President............................. Tamara J . Closs, ACUTA President, Georgetown University

Tech Talk: Pseudowire............................ Kevin Tanzillo, Dux Public Relations

Cell-Phone Directory to Be Published?

Web Tip: lnfo about and from ACUTA Events........................ Aaron Fuehrer, ACUTA Computer Svcs. Mgr.

Member Sites to See 5 Board Report.................. Cormine Piscopo, Providence College

DC Update................ Whitney Johnson, Retired, Northern Michigan Univ.

Welcome New Members

Causes Of Proteolytic Degradation Of Secreted Recombinant Proteins Produced In Methylotrophic Yeast Pichia Pastoris: Case Study With Recombinant Ovine Interferon-T, Jayanta Sinha, Bradley A. Plantz, Mehmet Inan, Michael Meagher

Papers in Biotechnology

It was observed that during fermentative production of recombinant ovine interferon-H (r-oIFN-H ) in Pichia pastoris, a secreted recombinant protein, the protein was degraded increasingly after 48 h of induction and the rate of degradation increased towards the end of fermentation at 72 h, when the fermentation was stopped. Proteases, whose primary source was the vacuoles, was found in in-creasing levels in the cytoplasm and in the fermentation broth after 48 h of induction and reached maximal values when the batch was completed at 72 h. Protease levels at various cell fractions as well as in the culture supernatant …

Stabilization Of Desert Sand Using Water-Borne Polymers, Shihab Wagiealla Abdalla Mohamed

Theses

Soil stabilization is one of the various applications that have benefited from the advances in polymeric materials. In this research, three water-borne polymeric emulsions with different chemical and physical properties were tested as stabilizers for sandy soil.

This study is divided into three parts. In the first part, the performance of the three emulsions in reducing the hydraulic conductivity and improving the mechanical properties of the sand was investigated. Specimens with polymer contents of up to 2 wt. % were prepared using two preparation methods, mixing and spraying. Both types of specimens exhibited a significant improvement in the studied properties. …

Modeling Of Multi-Converter More Electric Ship Power Systems Using The Generalized State Space Averaging Method, Madan M. Jalla, Ali Emadi, Geoffrey A. Williamson, Babak Fahimi

Electrical and Computer Engineering Faculty Research & Creative Works

based on the more electric ship (MES) concept, conventional mechanical, hydraulic, and pneumatic power transfer systems are replaced by electrical systems in different sea vehicles. Considering different levels of power requirements of various electrical loads and for the achievement of compact, light, safe, and efficient power supplies, implementation of multi-converter power electronics-based power systems is the most feasible option in the development of advanced navy vehicles. This paper presents a modular approach for the modeling and simulation of multiconverter MES power systems based on the generalized state space averaging method. MES power systems may consist of many individual converters connected …

Real Time State Estimation Of Multi-Converter More Electric Ship Power Systems Using The Generalized State Space Averaging Method, Madan M. Jalla, Ali Emadi, Geoffrey A. Williamson, Babak Fahimi

Electrical and Computer Engineering Faculty Research & Creative Works

This paper presents a real time state estimation algorithm for control and security maintenance of multi-converter MES power electronic systems. Estimation of the state variables of the system includes the effects of ripples and converter switching actions. the proposed state estimator is based on the Weighted Least Squares (WLS) approach. Generalized state space averaging technique in which we consider the DC value of the state variables, and their harmonics is used to model DC/DC converters for the state estimator. in this paper, after introducing the proposed approach and the concept of security and control assessments, results of applying the proposed …

Wind Tunnel Investigation Of The Static Stability And Control Effectiveness Of A Rotary Tail In A Portable Uav, Jose R. Rivera Parga

Theses and Dissertations

The Air Force Research Lab, Munitions Directorate, Flight Vehicles Integration Branch (AFRL/MNAV) developed a man-portable, carbon-fiber matrix UAV with a flexible rectangular wing of 24" span and 6" chord, 18.2" length. There is a need for the development of smaller and lighter UAV's to perform certain missions. The objective of this experimental study was to determine the behavior and the aerodynamic characteristics of rotary tails. The bird-inspired rotary tail mechanism studied enabled control of two degrees of freedom and was configured to provide elevator deflection and rotation. Its effects on the static stability and control effectiveness were measured using the …

Ultra Wide Band Signal Modeling For Radar Receiver Characterization, Robert J. Backscheider

Theses and Dissertations

Results for modeling, simulation, and analysis of interference effects that modern wideband signals have on existing narrowband radar system performance are presented. In particular, radar detection performance is characterized using a basic radar receiver model and operational parameters consistent with those of the ARSR-4 air route surveillance radar. Two modern wideband signals (interferers) are addressed in this work, including the GPS military signal (M-Code signal) and a direct sequence ultra wideband (DS-UWB) waveform meeting outdoor emission restrictions imposed by the Federal Communications Commission (FCC). Interference effects are characterized for an unmodulated sinusoidal pulse as well as linear frequency modulated (LFM) …

Non-Cooperative Detection Of Ultra Wideband Signals, Brett D. Gronholz

Theses and Dissertations

Techniques for the non-cooperative (non-matched filter) detection of impulse-like ultra wideband signals using channelized receiver architectures are developed and evaluated. Each technique considered is modeled and simulations conducted to characterize detection performance, the results of which are compared with the detection performance of three receivers: the matched filter receiver, which provides optimum detection performance in AWGN; the radiometer, or energy detector; and the multi-aperture cross correlation receiver. It is shown that a channelized receiver (with no downconversion) can provide approximately 2.5 dB improvement over the radiometer when performing detection using the temporal-temporal matrix (TTM). The TTM processing technique provides the …

Effects Of Variable Contact Load On Fretting Fatigue Behavior Of Shot-Peened And Un-Peened Titanium Alloy, Chia-Hawa Lee

Theses and Dissertations

Fretting fatigue occurs between two components in contact under relative motion and reduces fatigue life when compared with plain fatigue. Shot-peening, on the other hand, is the most commonly used cold working process to improve material fatigue resistance in aeronautical industries. Nearly all work accomplished to date has assumed a constant contact load while investigating fretting fatigue. The primary goal of this study was to explore fretting fatigue behavior under constant and variable contact load configurations using both shot-peened and un-peened specimens made up of Ti-6Al-4V alloy. Contact loads were applied with four different frequencies. Applied axial loads were also …

Consistency Results For The Roc Curves Of Fused Classifiers, Kristopher S. Bjerkaas

Theses and Dissertations

The U.S. Air Force is researching the fusion of multiple classifiers. Given a finite collection of classifiers to be fused, one seeks a new classifier with improved performance. An established performance quantifier is the Receiver Operating Characteristic (ROC) curve, which allows one to view the probability of detection versus the probability of false alarm in one graph. Previous research shows that one does not have to perform tests to determine the ROC curve of this new fused classifier. If the ROC curve for each individual classifier has been determined, then formulas for the ROC curve of the fused classifier exist …

Effect Of Coating Additives On The Rheological And Optical Properties Of Coated Papers, Burak Aksoy

Dissertations

Although additives are used in small amounts (below 2wt.% of the total solids) in a coating formulation, they play an important role in the runnability and end-use performance of the coating. Among coating additives, the use of insolubilizers and fluorescent whitening agents (FWA's) has increased due to theincrease in demand for higher quality graphic papers and packaging. Zirconium containing insolubilizers were studied for their rheological effects on silica ink jet coatings. Both zirconium species had an influence on the theological properties of the coating and its components. The interactions between thezirconium salts and the coating were found to be weak …

Fumed Metallic Oxides And Conventional Pigments For Glossy Inkjet Paper, Hyunkook Lee

Dissertations

Product development activity in the area of inkjet printing papers has accelerated greatly to meet the rapidly growing market for inkjet papers. Advancements in inkjet printing technology have also placed new demands on the paper substrate due to faster printing rates, greater resolution through increased drop volumes, and colorants added to the ink. To meet these requirements, papermakers are turning to pigmented size press formulations or pigmented coating systems. For inkjet coating applications, both the internal porosity of the pigment particles as well as the packing porosity of the coating affect print quality and dry time. Pores between the pigment …

Modeling The Strategic Impact Of Management Accounting Methods On The Implementation Of Lean Manufacturing, David Joseph Meade

Dissertations

This study examines the impact from the adaptation of lean manufacturing strategies on key external financial performance measures as reported by a number of management accounting methods. The research is not concerned with creating a justification for lean manufacturing strategies but rather it evaluates the inadequacies of standard financial reporting methods to accurately reflect operational improvements possible in the key performance measures through the early stages of a lean program.

ProModel simulation software is used in conjunction with Microsoft Excel and Visual Basic to create a simulated repetitive manufacturing environment and production planning and control system. The study examines the …

Nichtmonotone, Neuro-Symbolische Und Begriffliche Wissensverarbeitung, Pascal Hitzler

Computer Science and Engineering Faculty Publications

Diese Schrift dient dem Bericht uber die Hauptaspekte meiner Forschertatigkeit an der TU Dresden seit der Promotion. In diesen dreieinhalb Jahren war es mein Bestreben, selbststandig aktuelle, theoretisch fundierte und anwendungsbezogene Fragestellungen zu entwickeln und zu verfolgen.

Naturgemaß war meine Forschung in dieser Zeit vor allem zu Anfang sehr explorativ. Meine Suche konzentrierte sich dabei auf das Herausarbeiten theoretischer Zusammenhange. Ob ich einen Ansatz dann weiterverfolgte entschied sich anschließend aufgrund einer Evaluation aus angewandter Sicht.

Die in dieser Schrift dargestellten Forschungsansatze gedenke ich in Zukunft fortzufuhren. Sie bilden die Keimzellen fur langfristig angelegte angewandte und theoretische Untersuchungen. Ich werde in …

Overview Of The Japanese Guidelines For Seismic Retrofitting Of Rc Columns Using Frp Materials, Gustavo Tumialan, Hiroshi Fukuyama, Antonio Nanni

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The increasing uses of FRP materials for the strengthening and upgrade of buildings has motivated the international engineering community to produce guidelines for the proper design, handling and installation of the externally bonded FRP systems. Thus, independent efforts coordinated by different organizations such as the Japan Building Disaster Prevention Association (JBDPA) and the American Concrete Institute (ACI) have led to implementing appropriate provisions. the JBDPA guidelines mainly focus on seismic retrofitting of structural elements, which implies the strengthening for shear of deficient structural elements. This paper describes and comments on some of the design approaches provided by the JBDPA guidelines …

Carbon Nanotube Based Chemical And Biological Sensors, Srikanth Singamaneni

Masters Theses

Carbon nanotubes are among those wonderful molecules man has discovered by chance. Carbon nanotubes are sheets of graphite rolled up to form seamless cylinders. Their outstanding electrical, mechanical and thermal properties form the inspiration behind this work. This work investigates the possible application of carbon nanotubes as biological sensors for the detection of various biomolecules like Streptavidin and Mouse monoclonal Immunoglobulin-G. Electrical conductance changes of Carbon nanotubes for exposure to alcohol vapors were studied. This thesis demonstrates that these quantum wires can form highly sensitive biological and chemical sensors at molecular level. Although the main focus of the-research was chemical …

Integration Of Lean Manufacturing And Value Engineering Techniques To Improve The Internal Distribution System In A Manufacturing Company, Sripadjaraj Prahladaraj

Masters Theses and Doctoral Dissertations

The XYZ Corporation is located in Lafayette, Georgia. The company produces cooking ranges for the North American market. It has 1500 employees with a daily production capacity of 1000 to 1500 cooking ranges. The company is implementing lean manufacturing techniques to improve their performance. One of their projects is to develop a distribution system, which will help in streamlining the internal distribution of Very High Pressure (VHP) adhesive tapes. The aim of this research is to develop a lean distribution system by applying techniques of lean manufacturing systems. To understand the existing process of distribution, a flow diagram was created. …

Prediction Of Crack Growth Rate And Load Interaction Effects Using Damage Accumulation Model, Virender Goswami

Masters Theses

In damage tolerant designs, it is important to know the crack growth behavior of a material, so that sudden failure of a component can be avoided by determining a safe life. There are numerous models available to predict the crack growth rate. Among them the "crack closure model" is most often used for predicting the crack growth rate for different R-ratios and load interaction effects. However recently, the crack closure model has come under criticism by many authors to be flawed and overrated owing to its inherent drawbacks.

Therefore, a mathematical model for the fatigue crack propagation based on damage …

Feature Detection Using Linear Structure Modeling And Pca, Kawshif Muhammed Riaz Ahmed

Masters Theses

An algorithm to extract features from digital images such as cracks in concrete bridges for automated inspection is developed. The algorithm is based on the use of Principal Component Analysis (PCA). In general, PCA is used to reduce the dimensionality of a data set that consists of a large number of interrelated variables while retaining the variation present in the original data set. This ability of PCA will be used in this project to identify clusters using two training sets of images. Linear structure modeling is used to emphasize the image features (cracks) prior to applying PCA. Whole images processing …

Fast Measurements Of Flow Through Mitral Regurgitant Orifices With Magnetic Resonance Phase Velocity Mapping, Haosen Zhang, Sandra S. Halliburton, Richard D. White, George P. Chatzimavroudis

Chemical & Biomedical Engineering Faculty Publications

Magnetic-resonance (MR) phase velocity mapping (PVM) shows promise in measuring the mitral regurgitant volume. However, in its conventional nonsegmented form, MR-PVM is slow and impractical for clinical use. The aim of this study was to evaluate the accuracy of rapid, segmented k-spaceMR-PVM in quantifying the mitral regurgitant flow through a control volume (CV) method. Two segmented MR-PVM schemes, one with seven (seg-7) and one with nine (seg-9) lines per segment, were evaluated in acrylic regurgitant mitral valve models under steady and pulsatile flow. A nonsegmented (nonseg) MR-PVM acquisition was also performed for reference. The segmented acquisitions were …

Evaluation Of Us 119 Pine Mountain Safety Improvements: Ihsdm Analysis Of Post Construction, Will Conkin, Nikiforos Stamatiadis

Kentucky Transportation Center Research Report

The spot improvements on US 119 in Letcher County between Whitesburg and Partridge were an attempt to improve safety throughout the corridor. To achieve this goal, the roadway alignment and cross section were changed at various locations. In addition, problems related to truck traffic were considered in redefining the roadway geometries. The total length of the spot improvement locations was approximately 6.9 miles.

Using Fine-Grained Cycle Stealing To Improve Throughput, Efficiency And Response Time On A Dedicated Cluster While Maintaining Quality Of Service, Gary Stiehr

All Computer Science and Engineering Research

For various reasons, a dedicated cluster is not always fully utilized even when all of its processors are allocated to jobs. This occurs any time that a running job does not use 100% of each of the processors allocated to it. Keeping in mind the needs of both the cluster’s system administrators and its users, we would like to increase the throughput and efficiency of the cluster while maintaining or improving the average turnaround time of the jobs and the quality of service of the “primary” jobs originally scheduled on the cluster. To increase the throughput and efficiency of the …