Engineering Commons^™

Understanding Market Stakeholder Perspectives: Application In The Biopharmaceutical Industry, Halvard Nystrom, Kalayanee Poon-Asawasombat

Engineering Management and Systems Engineering Faculty Research & Creative Works

New products are sometimes perceived as risky. This article contributes a process that new product development teams can use to better understand stakeholders' concerns. the stakeholder analysis process is appropriate for products that can be perceived as risky since it enables developers to address key issues of concern prior to new product introduction, mitigating market acceptance risk. It uses a stakeholder model that facilitates dialogue to understand market risks and guide the assessment process. This article includes a case study describing a successful application of introducing biopharmaceutical products, as well as some of the key findings to demonstrate usefulness. © …

Seismic Bahavior Of Reinforced Concrete Liquid Storage Tanks, Iman Shawky Abdel-Rahman

Archived Theses and Dissertations

This thesis presents a study of the effects of seismic loading on reinforced concrete liquid storage tanks. Stresses and displacements were computed by the finite element method to ascertain that they remain within an acceptable safety range when the tank is subjected to earthquake ground accelerations of varying intensities. In the analysis different parameters were considered. This included tank radius, liquid height, and shell thickness, loading conditions resulting from both hydrostatic and hydrodynamic pressures, and a variety of boundary conditions at the top and bottom of the tank, including a cover dome. The finite element package (ABAQUS) was used to …

Utilization Of Municipal Solid Waste Rejects In The Production Of A Recycled Plastic Waste Composite Material, Mohamed Kamal Abou Khatwa

Archived Theses and Dissertations

The solid waste disposal problem has grown significantly in the last decades imposing a lot of pressure on disposal and treatment acts. In the past, incineration and landfilling were the common methods for disposing of products of municipal solid waste. With the increasing volumes of waste generation and the legislative restrictions of these treatment methods, reuse of bulk waste is foreseen as the best alternative to disposal. Due to the current widespread use of plastic products in daily life, post consumer plastics now contribute significantly to municipal solid waste generation rates with a contradicting low participation in waste minimization practices. …

The Localized Corrosion Behavior Of 6% Mo And 316l Stainless Steels In Chloride Media And The Effect Of Applied Mechanical Stress, Houssam El-Din Sabry Ahmed

Archived Theses and Dissertations

Electrochemical techniques were applied to study the crevice corrosion resistance of two types of stainless steel alloys namely, conventional 316L and super austenitic 6% Mo in acidified 3% NaCl solution at room temperature. Potentiodynamic results showed that 6% Mo alloy possessed a remarkable resistance to crevice corrosion compared to 316L alloy when tested in the same solution. The breakdown potential at which passivity broke down for 316L alloy was 0.00 m V, SCE, the corresponding value for 6% Mo alloy could not be reached up to the potential value of 700 m V, SCE. 316L alloy suffered extremely from crevice …

Synthesis And Optimization Of Digital Systems For Low Power At Logic Level Of Abstraction, Ihab Mostafa Amin Amer

Archived Theses and Dissertations

In this thesis we tackle one of the most important fields of research, which is reducing power consumption in digital systems. The importance of this field comes from the fact that nowadays, several digital devices are intensively used in our daily life. Thus, minimizing their power consumption is a common demand from the technological as well as the economical point of view. Some basic definitions in the low power design field are introduced. Besides, a preview of different efforts that were exerted in the field of reducing power consumption of digital systems at various levels of abstraction is presented. A …

Texture Classification Using Transform Analysis, Mary Habib

Archived Theses and Dissertations

The work presented in this thesis deals with the application of spectral methods for texture classification. The aim of the present work is to introduce a hybrid methodology for texture classification based on a spatial domain global pre-classifier together with a spectral classifier that utilizes multiresolution transform analysis. The reason for developing a spatial pre-classifier is that many discriminating features of textures are present in the spatial domain of the texture. Of these, global features such as intensity histograms and entropies can still add significant information to the texture classification process. The pre-classifier uses texture intensity histograms to derive histogram …

Bs News

Building Services Engineering

No abstract provided.

Scattering Of Elastic Waves In Damaged Media, Liyong Yang, Joseph A. Turner

Nebraska Center for Materials and Nanoscience: Faculty Publications

The scattering of elastic waves in a medium with damage from microcracking is discussed. The influence of damage from penny-shaped microcracks within a homogeneous medium is considered. The microcracks are assumed to be randomly oriented and uniformly distributed. Explicit expressions are derived for the attenuation of longitudinal and shear elastic waves in terms of the damage parameter and the effective elastic moduli of the medium. A generalized tensor-based approach is used such that the results are coordinate free. The derivation is based upon diagrammatic methods. The problem is formulated in terms of the Dyson equation, which is solved for the …

Image Segmentation With Ratio Cut, Song Wang, Jeffrey Mark Siskind

Faculty Publications

This paper proposes a new cost function, cut ratio, for segmenting images using graph-based methods. The cut ratio is defined as the ratio of the corresponding sums of two different weights of edges along the cut boundary and models the mean affinity between the segments separated by the boundary per unit boundary length. This new cost function allows the image perimeter to be segmented, guarantees that the segments produced by bipartitioning are connected, and does not introduce a size, shape, smoothness, or boundary-length bias. The latter allows it to produce segmentations where boundaries are aligned with image edges. Furthermore, the …

Afci Quarterly Input – Unlv April Through June, 2003, Harry Reid Center For Environmental Studies. Nuclear Science And Technology Division

Transmutation Research Program Reports (TRP)

The University of Nevada, Las Vegas supports the AFCI through research and development of technologies for economic and environmentally sound refinement of spent nuclear fuel. The UNLV program has four components: infrastructure, international collaboration, student-based research, and management and program support.

Quarterly Report For The Trp Project, March–June 2003, Samir Moujaes, Yitung Chen, Kanthi Kiran Daiska, Chao Wu

Transmutation Sciences Materials (TRP)

The MTL is assumed to be a 5m long rectangular loop with a circular cross-section. Because of the non-symmetry, and due to the active participation of the secondary flows due to the elbows present in the rectangular loop model, the geometry is considered as a 3D model.

When the regions of maximum corrosion and precipitation are compared, they fall in the same zone for both the analytical and simulated models. The reason for a larger concentration flux in the case of turbulent flow than for the laminar flow can be explained by the concept of higher lateral diffusion in the …

Inside Unlv, Kevin Force, Gian Galassi, Carol C. Harter, Stuart Mann

Inside UNLV

No abstract provided.

Students' Perceptions Of Both The Certainty And The Deterrent Effect Of Potential Consequences Of Cheating, Cynthia J. Finelli, Trevor S. Harding, Donald D. Carpenter, Honor J. Passow

Materials Engineering

No abstract provided.

Paints And Their Environmental Impacts On Human Health In The U.A.E, Masara Y. Al-Ameri

Theses

This thesis records the findings of a research program related to "Paints and Their Environmental Impacts on Human Health in the U.A.E". The study recommends attempt to find out what paint types are of a less harmful influence on human health within different building types in United Arab Emirates due to environmental conditions.

According to Larry W. Canter (1997) "Environmental Impact Assessment" can be defined as "the systematic identification and evaluation of the potential impact (effects) of proposed projects, plans, programs, or legislative actions relative to the physical- chemical, biological, cultural, and socioeconomic components of the total environment. The primary …

Cooperative Path Planning For Timing Critical Missions, Timothy W. Mclain, Randal W. Beard

Faculty Publications

This paper presents a cooperative path planning approach for teams of vehicles operating under timing constraints. A cooperative control approach based on coordination variables and coordination functions is introduced and applied to cooperative timing problems. Three types of timing constraints are considered: simultaneous arrival, tight sequencing, and loose sequencing. Simulation results demonstrating the approach are presented.

Efficient Resource Allocation And Call Admission Control In High Capacity Wireless Networks, Jiongkuan Hou

Dissertations

Resource Allocation (RA) and Call Admission Control (CAC) in wireless networks are processes that control the allocation of the limited radio resources to mobile stations (MS) in order to maximize the utilization efficiency of radio resources and guarantee the Quality of Service (QoS) requirements of mobile users. In this dissertation, several distributed, adaptive and efficient RA/CAC schemes are proposed and analyzed, in order to improve the system utilization while maintaining the required QoS.

Since the most salient feature of the mobile wireless network is that users are moving, a Mobility Based Channel Reservation (MBCR) scheme is proposed which takes the …

Effects Of Implementation Of Decaborane Ions In Silicon, Cheng Li

Dissertations

The next generations of Si microelectronic devices will require ultra shallow p-type junctions formed by implantation of B ions with energies below 1 keV, at which available beam currents are severely limited by space charge effects. To solve this problem, decaborane (B₁₀H₁₄) cluster ion implantation has been suggested as an attractive alternative to conventional B implants, because one decaborane ion implants ten B atoms simultaneously and each of the B atoms only carries approximately 1/11 of the total ion energy. Thus the same implantation depth and dose as with monomer B ions can be obtained using …

New Full Wave Theory For Plane Wave Scattering By A Rough Dielectric Surface - The Fictitious Current Method, Byung-Tae Yoon

Dissertations

A new full wave method for scattering of plane waves from a rough dielectric surface is developed. This new theory begins by postulating a zero-order field solution which does not satisfy Maxwell's source-free field equations. The zero-order field, however, is made to satisfy Maxwell's source equations. This is done by introducing a fictitious volume current distribution. Since the original problem does not possess a volume current distribution, its introduction represents a measure of the error in the postulated zero-order solution. To improve this solution, the fictitious volume current distribution is cancelled by the introduction of a second fictitious current distribution, …

Dynamic Multi-Ramp Metering Control With Simultaneous Perturbation Stochastic Approximation (Spsa), Jiangtao Luo

Dissertations

Ramp metering was proven to be a viable form of freeway traffic control strategy, which could eliminate, or at least reduce, freeway congestion. In this study, the development of ramp metering control strategies, models, and constraints (e.g., meter locations, ramp storage capacities, lower and upper bounds of ramp metering rates) are discussed in detail. The pre-timed and demand/capacity metering control strategies were first evaluated, while the potential metered ramps were determined. A Simultaneous Perturbation Stochastic Approximation (SPSA) algorithm is proposed to dynamically optimize multiple-ramp metering control by maximizing the total throughput subject to a number of constraints. The ramp metering …

Theoretical And Experimental Studies Of The Field-Induced Phenomena In Flowing Suspensions, Nikolai Markarian

Dissertations

The present work describes results of experimental and theoretical studies of the behavior of dilute suspensions subject to high gradient AC electric fields. When a spatially non-uniform electric field is applied to a suspension, in which the particles and the suspending fluid have different dielectric permittivities andlor conductivities, the particles migrate towards the regions of high or low electric field strengths depending on the sign of their polarization. This phenomenon, referred to as dielectrophoresis, has found numerous applications for the control and manipulation of the particle motions.

Presented in Chapter 3 are the results of studying the field -induced motion …

Development Of A Multivariate Logistic Model To Predict Bicycle Route Safety In Urban Areas, Cheryl Allen-Munley

Dissertations

In response to the renewed appreciation of the benefits of bicycling to the environment and public health, public officials across the nation are working to establish new bicycle routes. During the past two decades, a number of methods have been endorsed for the selection of "suitable" bicycle routes. These methods are limited in that they do not explicitly address bicycle safety nor do they reflect urban conditions.

The purpose of this research is to develop an objective bicycle route safety rating model based on injury severity. The model development was conducted using a logistic transformation of Jersey City's bicycle crash …

Investigation Of An Integrated Regional Environmental Watershed Methodology, Marshall R. Boggio

Dissertations

Recent public awareness of the environment has placed increased emphasis on the health and current state of the regional watershed. The watershed has been defined as that area in which water flowing across and beneath a given land surface drains into a specific stream or river, ultimately flowing through a single point or outlet on that stream or river. Since the processes involved are many and are analyzed in the literature on an individual basis, the current investigation attempts a more holistic approach by suggesting a methodology that integrates all elements of the hydrologic cycle. The investigation utilizes the area …

Time-Frequency Investigation Of Heart Rate Variability And Cardiovascular System Modeling Of Normal And Chronic Obstructive Pulmonary Disease (Copd) Subjects, Douglas Alan Newandee

Dissertations

A study has been designed to add insight to some questions that have not been fully investigated in the heart rate variability field and the cardiovascular regulation system in normal and Chronic Obstructive Pulmonary Disease (COPD) subjects. It explores the correlations between heart rate variability and cardiovascular regulation, which interact through complex multiple feedback and control loops. This work examines the coupling between heart rate (HR), respiration (RESP), and blood pressure (BP) via closed-loop system identification techniques in order to noninvasively assess the underlying physiology.

In the first part of the study, the applications of five different bilinear time-frequency representations …

Spatio-Temporal Correlation Models For Indoor Mimo Channels, Kaustubha Raghukumar

Theses

Accurate modeling of the spatio-temporal cross-correlation between the subchannels of a multiple-input multiple-output (MIMO) channel is an important prerequisite of multi-element antenna system design. In this thesis, a new model for indoor MIMO channels is proposed, and a closed form expression for the spatio-temporal cross-correlation function is derived. This new analytical correlation expression includes many physical parameters of interest such as the angle-of-arrivals at the base station and the user, the associated angle spreads, and other parameters, in a compact form. Comparison of this model with narrowband indoor MIMO data collected at Brigham Young University exhibits the utility of the …

Experimental Study Of Ignition Of Mechanical Alloy And Pure Metal Powders, Ruslan Mudryy

Theses

Mechanical alloys of Al Mg, AI Zr, Al Ti, Al Li, Al C, Al Mg H, B Mg, B Al, and B Ti were produced and tested for possible applications as high energy density additives to fuels, propellants, explosives, and incendiaries. These new materials are metastable, supersaturated, nanocrystalline solid solutions that include a base metal as a solvent and another component (metal or gas, e.g. hydrogen) as a solute. Phase changes occurring in such materials during ignition and combustion are expected to significantly affect both ignition and bum rates. This experimental program focused on the characterization of ignition kinetics of …

The Consolidation Analysis Of A Clay Layer In The City Of Belem Do Para, Brazil, John Bezerra Jr.

Theses

In this study, an analysis was done on a particular clay layer found in the city of Belem do Para, Brazil. Various soil tests were conducted including a consolidation analysis. Data were gathered and analyzed in order to obtain a better understanding of how the soil responds under certain loading conditions. There have been no previous studies done on this material and so when it has been encountered in the field geotechnical engineers provide the safest, but not necessarily best design method possible. In the case of large buildings, piles are driven past this material to competent sand. There have …

Shape Finding Of Fabric Structures Using Grid Method, Armin Bischof

Theses

Fabric structures can span large distances with a very low self-weight, which makes them very efficient for covering huge areas. They have attractive shapes and an appealing architecture. These properties make them very popular and they are used in many different kinds of buildings. Airports, stadiums and halls are typical examples where the use fabric structures is often recommendable.

Fabric structures are built mainly out of fabric and cables; two structural members that can only take tension stresses. Therefore these structural members must be prestressed in such a way that their shape can carry all loads that might affect the …

Improving The Process Of Laser Retinal Eye Surgery Using Electro Static Micro Mirrors, Narashiman Chakravarthy

Theses

This thesis describes an improved system for laser eye surgery. The system incorporates hardware based image matching and MEMS micromirrors for feedback control of laser positioning on the eye. Many benefits are described in this thesis, such as nulling out eye movement, tracking laser firing history, enabling precise control of laser firing locations and preventing firing accidents. The aim of this work is to frame this improved laser surgery concept and prove the principle of various components of the system. A featured accomplishment is the modeling and simulation of a prototype microcontroller using VHDL that may be incorporated as part …

Labview-Controlled Stimulus Presentation On A Monitor For Smooth Pursuit Eye Movement Experiments, Florence Bautista Chua

Theses

Smooth pursuit is an example of how movements in the visual world guide involuntary oculomotor movements. A current system to study eye movements uses an oscilloscope screen. A computer screen offers many advantages: a greater visual field, the use of shapes, 32 bits of colors, and increased timing accuracy. To control stimulus display on a computer monitor, instrumentation was developed in LabVIEW. Initial studies supported a draw/redraw to erase method for stimulus presentation. An experiment compared the computer monitor to the oscilloscope. Indeed, the monitor display was an improvement over the oscilloscope for vision research.

Hop-Limited Routing For Multihop Cellular Networks, Cem Dincer

Theses

In recent years, conventional cellular systems have experienced evolution in fields of data oriented services. During this period, the requirement for high data-rate stimulated new research proposals, which resulted in a new architecture: Multihop Cellular Networks (MCN), where multihop structure enables mobile stations to forward packets from other mobile stations to the base station on the uplink, and in turn, forward packets to other mobile stations from the base station on the downlink. In this thesis, a new routing algorithm is introduced for MCNs in order to limit the number of hops between the base station and the mobile stations …