Engineering Commons^™

An Investigation Of The Effects Of Pozzolans On New Mexico Concrete Aggregates, Harry W. Montgomery

Civil Engineering ETDs

It was the purpose of this investigation to determine some of the effects a pozzolan has on Portland cement concrete when New Mexico aggregates are used. The specific items investigated were (1) to determine the effects of a pozzolan on the alkali aggregate expansion in concrete; (2) to show the effect on the compressive strength of concrete and the tensile strength of mortar briquettes when part of the Portland cement is replaced with a pozzolan; (3) to determine whether or not the “Mason Jar Expansion Test” would give reliable results; and (4) to determine whether or not an aggregate, with …

Copper Converter: Basic Research Testing With A Plastic Model Converter And Four Types Of Refractories, Arthur C. Bigley Jr.

Bachelors Theses and Reports, 1928 - 1970

In recent years there has appeared an increasing number of papers on converting operations as related to thermodynamics. This approach is a powerful, potential tool. However, the development of new ideas and changes must rely on accurate basic information.

Microradiography Of Metals And Alloys Using A Medical X-Ray Unit, W. R. Byrne

Bachelors Theses and Reports, 1928 - 1970

There is no doubt that the microradiograph technique is of value to the metallurgist. A three-dimensional picture to supplement the photomicrographs should give a true picture of the microstructure. Microradiography can be used where etchants can not differentiate between the various components or where no etchant can be found suitable for a particular alloy.

Comminution Studies, George A. Grandy

Bachelors Theses and Reports, 1928 - 1970

Comminution, reduction in size, is one of the most important, yet least understood, steps in mineral dressing. So that more efficient comminuting devices may be designed and constructed, a better knowledge of the relationship between energy consumption and size reduction is desired. Occasional studies during the last 100 years have produced a few "laws" purporting to describe this relationship. In each case, the promulgators and supporters of these laws have presented experimental evidence for their verification. Obviously, all of these advocated practices cannot be correct. To the mill designer, the problem is "Which, if any, of these laws are valid." …

Secondary Recrystallization In Copper, James E. Thompson

Bachelors Theses and Reports, 1928 - 1970

The purpose of this thesis is to study the conditions under which secondary recrystallization will take place in copper. The variables considered were the time annealing, the temperature of annealing, and the degree of cold work undergone by the specimen before it was subjected to the heat treatment.

A Microwave Technique For Determining The Electronic Properties Of A Moving Plasma, Bernard Hayes

Electrical and Computer Engineering ETDs

A microwave interferometer technique which may be used as a diagnostic tool for determining the electronic properties of a moving plasma is described and analyzed. The plasma and microwaves are confined in a wave guide and longitudinal observation is employed. The complex reflection coefficient determined from resultant standing-wave pattern provides the means for obtaining the complex dielectric constant, conductivity, electron concentration and collision frequency of electrons with molecules in the plasma. The plasma used for these experiments is the reaction products of a gas detonation.

Functional And Economic Considerations Of An Electrical Line Feeding Large Concentration Loads, Seth O. Lewis

Electrical and Computer Engineering ETDs

This paper discusses the considerations required for selecting particular characteristics of [transmission lines] and presents an original method of obtaining the most economical solution. A typical problem at the Public Service Company of New Mexico is solved to illustrate the usefulness of this method.

Growth Of A Preferentially Oriented Aluminum Single Crystal, John George Bjeletich

Bachelors Theses and Reports, 1928 - 1970

When studying some anisotropic property of a specific metal, such as the critical shear stress of aluminum, it is desirable that the test specimen be a single crystal with the crystal axes preferentially oriented. Therefore, it is necessary to obtain a single crystal by one of the methods mentioned and by use of x-rays to determine the orientation. Once the single crystal is obtained and the orientation known, it is possible to grow a preferentially oriented aluminum single crystal by a method generally known as "seeding". The purpose of this thesis problem was to grow a crystal by utilizing the …

The Identification Of Montana Clays By X-Ray Analysis, James Francis Donovan

Bachelors Theses and Reports, 1928 - 1970

This investigation is concerned primarily with the determination of the various clay minerals comprising certain deposits through the state. This investigation was accomplished with the use of X-Ray diffraction equipment and it can be easily understood why this equipment has been of such benefit to the clay mineralogist.

The Macromosaic Structure Of Lead Single Crystals, Eldon J. Nicholson

Bachelors Theses and Reports, 1928 - 1970

The purpose of this investigation is to examine this structure [macromosaic] to determine any properties or characteristics peculiar to it that could shed light on its cause or on the basic mechanism of crystal growth from the melt.

Design And Use Of A High Power Laser For Plasma Generation Studies., Philip N. Mace

Electrical and Computer Engineering ETDs

The advent of high power lasers to the technological scene has introduced the possibility of creating new effects utilizing the interaction of this high intensity light with matter. C. M. Fowler and D. B. Thomson of the Los Alamos Scientific Laboratory suggested in 1963 the possibility of using a high power laser to pre-ionize and heat a target material to be contained in an explosively driven theta pinch machine. There had been calculations performed by John Dawson, Princeton University, and A. Engel­hardt, Westinghouse Research Laboratories, which indicated that such an approach was theoretically feasible. The laser powers required, however, were …

Determination Of Required Component Reliability From System Reliability Requirements, Arthur M. Breipohl

Electrical and Computer Engineering ETDs

No abstract provided.

Autoclave Leaching Of Montana Chromite, Leonard S. Greely

Bachelors Theses and Reports, 1928 - 1970

The purpose of this investigation was to determine the feasibility of caustic autoclaving of Montana chromite in order to recover the chromium in a relatively pure solution of sodium chromate.

A Study Of The Inlet Characteristics And Entrance Losses Of Pipe Culvert With A Flush Mounted, Sharp Edged Inlet, Luke Lea Callaway Jr.

Masters Theses

"Of all hydraulic structures, culverts are by far the most numerous. Lack of understanding of the functioning of culverts has resulted in many of them being implaced improperly and as a result, they function with less efficiency and at reduced capacity. Much has been written regarding the flow of water in open channels, culverts included, but little has been done regarding inlet conditions. It is necessary in the design of culverts, as with any other structure, that conditions which govern the operation of the structure be established. This paper is a study of the inlet conditions of a circular cross …

Analysis And Synthesis Of A Current Regulator System, William P. Aiello

Electrical and Computer Engineering ETDs

This report describes a practical current regulator system used to accurately control the current delivered by a 500 kilowatt motor-generator unit. The generator supplies its current of 2000 amperes at 250 volts to a large water-cooled air-core solenoid used by LASL Group P-7 for experiments in connection with the Sherwood program.

After a general discussion of the system specifications and the basic regulator loop, each of the components in the basic regulator loop is described in considerable detail. The description, in most cases, is mathematical in nature although many circuit diagrams are included with brief descriptions when necessary for proper …

A Method Of Design For Spiral Reinforced, Eccentrically Loaded, Concrete Columns, Lloyd O. Senter

Masters Theses

"This thesis presents a method of designing spiral reinforced, eccentrically loaded, concrete columns on the basis of the 1957 American Association of State Highway Officials specifications.

Equations from AASHO, in conjunction with equations derived in this thesis, are programmed for and solved by the IBM 650 digital computer. The data obtained from the computer is plotted such that, given the normal load and moment on a column, the minimum required area or reinforcing steel may be read directly from the graph.

The derivation or equations, the computer program, and the graphs are included in the thesis"--Introduction, page 1.

Heat Transfer Coefficients In Artificially Roughened Pipes, Mehmet Hayati Turan

Masters Theses

"The purpose of this investigation is to determine experimentally the effects of three different types of artificial roughness on the convective heat transfer coefficient in a pipe and compare these values with that for a smooth pipe for turbulent flow"--Introduction, page 7.

Temperature Distribution In A Semi-Infinite Solid As A Function Of The Input Heat Flux, Lloyd Carl Laciny

Masters Theses

"In this thesis the problem of varying heat flux into a semi-infinite solid initially at zero temperature is investigated. Varying heat flux means that the heat transferred to the solid by its surroundings is a function of time; in this particular problem it is chosen to be an exponential function of time. A semi-infinite solid is one which is bounded by only one plane.

This subject has achieved considerable importance in the field of space technology. A body in space is beyond the realm of aerodynamic heating and non-uniform skin temperatures reached as a result of radiation from a high …

Some Dynamic Creep Characteristics Of Gypsum, Ikram-Ul-Haq Dar

Masters Theses

"A review of literature concerned with time-dependent deformation of geologic and non-geologic materials is presented. A static loading machine and a four unit dynamic loading unit was designed and assembled to evaluate static and dynamic creep properties of gypsum. The tests were run for various levels of static loads, and superimposed dynamic loads. Investigations were carried out to determine the relationships, if any, between impact energy, impact velocity and momentum, and dynamic strains. Viscoelastic coefficients were determined for the investigations. The conclusion was presented that time-dependent strain in the dynamic creep tests of the particular gypsum rock tested is a …

Heat Transfer In A Vortex Flow Metal To Air, Elisha Rachovitsky

Masters Theses

"In this study heat transfer in a vortex flow has been investigated experimentally and analyzed qualitatively.

Air was forced through a Ranque tube in order to get a swirling turbulent flow in its "hot" section. The test section, having a diameter of .355 inches and a length of 27.5 inches, was heated by an induction coil.

Three types of flow were under investigation: a linear turbulent flow, a vortex uniflow and a mixed vortex-linear turbulent flow.

The experiments covered a range of tube-wall temperature from 570 to 900 Deg. R and inlet pressure to the vortex generator ranged from 25 …

Methods For Calculating The Minimum Amortization Tonnage And Maximum Present Value For An Ore Body, Garrett M. Sainsbury

Masters Theses

"The discussion is divided into three parts. Part I describes a procedure for determining the mining rate that gives the minimum amortization tonnage required of an ore body, and the amount of that tonnage. The basic idea is that amortization tonnage is equivalent to the estimated capital costs, including interest, divided by the estimated operating profit per ton. Both capital costs and operating profit per ton can be expressed as functions of mining rate by making use of empirical equations. Therefore, amortization tonnage can be expressed as a function of mining rate. The amortization tonnage is calculated for a series …

High Temperature Oxidation Of Nickel, Virgil R. Friebel

Masters Theses

"Using a sensitive volumetric technique, a study was made of the kinetics of oxidation of nickel at 1200° C. and 1300° C. Three purities of nickel were used for the investigation which was limited to the initial three hours of reaction.

The rate of oxidation of nickel followed the parabolic rate law after an initial period of deviation which lasted up to 40 minutes. No direct correlation was found between the oxide thickness and the end of the period of deviation from the parabolic rate law.

The purity of the nickel was found to have a marked effect on the …

The Constitution Of Magnesium-Rich Magnesium-Zirconium Alloys, Kenneth Allen Fowler

Masters Theses

"The magnesium-zirconium system has been studied to 0.8 per cent zirconium which represents the limit of solubility of zirconium in liquid magnesium at 950°C. Alloys have been prepared by two methods of alloy additions, and the results compared. Microstructural studies have been made of the alloys in the cast, extruded, and heat-treated conditions. The limit of solid solubility has been determined on the basis of resistivity and temperature coefficient of resistivity measurements, as well as by metallographic examination, with good agreement. A secondary structure resulting from precipitation of a second phase within cored regions of the alloy has been studied …

The Redesign And Construction Of A Rotating Disc Contactor, Richard Henry Okenfuss

Masters Theses

"Liquid-liquid extraction has played a major role in the processing of nuclear fuels. The Department of Chemical Engineering of the Missouri School of Mines and Metallurgy realizing this, petitioned the Atomic Energy Commission for funds to design and construct an instructional facility representing the chemical processing of nuclear fuels. With this unit and its solvent recovery equipment, in which stress is placed on extraction and distillation, not only are the principles of nuclear fuels processing demonstrated, but the more basic concepts of mass and energy transfer are also illustrated. Extraction depends upon solubility differences to achieve a transfer of a …

The Effect Of The Rare Earth Elements On The Hot Workability Of Ingot Iron, L. A. Neumeier

Masters Theses

"The effect of mischmetal and rare earth oxides on the hot workability of ingot iron in the hot-short region was studied. Thirteen heats were melted in air in a basic-lined induction furnace. All heats were thoroughly deoxidized with aluminum prior to the rare earth additions. Mischmetal was added in amounts of 0.1, 0.3 and 0.5 per cent. Rare earth oxides were added in amounts of 0.1 and 0.2 per cent. Temperatures were maintained at approximately 2900°F and holding intervals between mischmetal additions and pouring at two minutes. Bars were hot rolled and swaged for hot twisting in the hot-short region. …

Determination Of Vapor-Liquid Equilibrium Data By Continuous Distillation, David William Bunch

Masters Theses

"The procuring of experimental vapor-liquid equilibrium data has been a problem of considerable importance to chemical engineers for a number of years. Modern distillation theory and practice have made accurate vapor-liquid equilibrium data practically a necessity.

Using conventional methods for determining vapor-liquid equilibrium data, an experimenter can obtain only a single vapor-liquid equilibrium composition per trial. Ramalho working with Tiller has developed a new method which makes possible the determination of all values of the vapor and liquid concentrations in a single experiment.

The work done by Ramalho indicated that the necessity for very precise temperature measurements presented a serious …

Segregation Method As Possible Process To Beneficiate Oxidized Lead Ores, Jose Molfino Tomasio

Masters Theses

"In this investigation it has been demonstrated that the Segregation Process has merit for treating oxidized lead ores.

The process comprises heating the crushed ore with salt and coal at about 750° C. to produce metallic lead attached to the carbon particles, which then is recovered by conventional flotation methods.

The quantities of sodium chloride and coal required for the best segregation of lead obtained in this work was 1.0 percent of coal and 1.0 percent of salt by weight.

Good segregation was obtained by using salt and coal as fine as 65 or 48 mesh. Segregation varied with the …

The Separation Of Selected Radioactive Fission Products By Electrodialysis, Jerry David Vie

Masters Theses

"The recent advent of nuclear energy has opened an era of almost unlimited power and countless problems. A problem of extreme importance is the recovery of unburned nuclear fuel and the claiming of transmutation products, such as Pu²³⁹ and U²³³, from the irradiated fuel elements. The chemical processing must also separate the fission products from the fissionable material if the fuel is to be used again.

At present, the irradiated fuel elements are stored for 90 to 120 days to allow the intense short half-life activity to decay. After "cooling down", the nuclear fuels are separated from …

Water Resources Development -- An Analysis Of Economic Justification Practices Of The Corps Of Engineers, Kerwood W. Barrand

Masters Theses

"Presented herein is a brief analysis of the economic justification practices of the Corps of Engineers as commonly implemented in proposals concerning water resources projects. Where applicable, recommended methods are compared to similar methods advocated for, and accepted by, private engineering firms in similar situations.

The major problem exists in the lack of a profit motive in programs undertaken with the use of public funds. However, a profit can be said to have been realized in public works programs if the total benefits of the programs to all the people exceed the costs of these programs and, further, if the …

An Experimental Investigation Of Receiver System Sensitivity, James Henry Johnson

Masters Theses

"A method of determining the minimum detectable power density incident at the receiving antenna of a UHF receiver is proposed. The minimum detectable power density is the power density required to produce a signal-to-noise ratio of unity in the output of the receiver. The proposed method includes the receiving antenna impedance, the necessary connecting transmission lines, and the receiver impedance.

It is shown that an error in the antenna directivity will produce a significant error in the overall sensitivity of a receiving system. Since the directivity is the most difficult system variable to determine experimentally, it is probably the limiting …