Engineering Commons^™

The Design And Construction Of An Instrument For Calibrating Accelerometers, Richard Rabenau

Masters Theses

"The purpose of this work was to design and construct a facility to calibrate accelerometers. A ceramic piezoelectric shaker and modified Michelson interferometer together with necessary electronic equipment were used. The system produced accurate and stable acceleration at five discrete points from 1,000 to 5,000 cycles per second. the maximum calibration levels were approximately 50 g's"--Abstract, page ii.

A Circularly Polarized Corner Reflector Antenna, Walter Ronald Koenig

Masters Theses

"Image theory is used to develop the far field and polarization equations for a ninety degree corner reflector antenna. These equations are in terms of spherical coordinates, the length of the dipole element, the distance of the dipole from the corner of the reflector, and the angle of tilt of the dipole element with the apex of the corner. The equations are simplified to give the far fields in the vertical and horizontal planes for the special case of a half-wavelength dipole. An expression to calculate the distance of the dipole from the corner necessary to give circular polarization broadside …

Construction Of A Capillary Viscometer And The Study Of Non-Newtonian Liquids, Hsun Kuang Yang

Masters Theses

"A capillary tube viscometer was built for the purpose of investigating the fluid properties of non-Newtonian aqueous CMC and Carbopol solutions. The viscometer was tested with Newtonian liquids (glycerine, water and two different oils) having known viscosities to insure that the viscometer was operating correctly. The shear stress-shear rate data obtained for different concentrations of CMC and Carbopol solutions were correlated using the simple power law model. The power law constants were only slightly affected by saturating the solution with iodine and carbon tetrachloride. Aging had very little effect on the viscosities of the CMC solutions but had a considerable …

The Thermodynamics Of The Zno-Fe₂O₃-Fe₃O₄ System, Robert Lee Benner

Doctoral Dissertations

"The purpose of this investigation was to (1) experimentally locate certain phase boundaries in three isothermal sections of the zinc oxide - ferric oxide - magnetite phase diagram, (2) to experimentally determine some of the thermodynamic properties of the zinc oxide - ferric oxide - magnetite system, (3) to use the thermodynamic properties of the zinc oxide - ferric oxide - magnetite system to evaluate the pseudo-binary system between zinc ferrite and magnetite, (4) to construct a compound stability diagram for the zinc-iron-oxygen-sulfer system"--Introduction, Statement of the Problem, page [1].

Drag Reduction In Newtonian Polymer Solutions, Harry C. Hershey

Doctoral Dissertations

"Prior work in the area of drag reduction has been mainly limited to aqueous solutions. Theoretical and empirical analyses of the resulting data in aqueous solutions have been hindered by the fact that some polymers cause drag reduction and others do not...This investigation was directed to the study of how the size and configuration of the polymer molecule in solution affected drag reduction and the related phenomenon of turbulence suppression. Apparatuses were designed and built to measure viscometric flow, curves, friction factors, velocity profiles, and normal stresses (by a jet thrust technique developed by Metzner and associates)"--Summary, page 1-2.

Internal Friction Of Mixed-Alkali Silicate Glasses, James E. Shelby

Doctoral Dissertations

"The mixed alkali effect in silicate glasses was examined from internal friction measurements made over the temperature range from -190 to 500⁰C and at a frequency of 0.4 Hz. Supplemental measurements of the activation energy for the different internal friction peaks, dynamic shear modulus, density, and index of refraction were also made. All measurements were confined to silicate glasses containing mixtures of Li-Na, Li-K, Li-Rb, Li-Cs, Na-K, Na-Rb, Na-Cs, and K-Rb. Rötger's interpretation of the internal friction of mixed-alkali silicate glasses is shown to be incorrect. A previously unreported internal friction peak was observed whenever two different alkali oxides were …

The Microbial Hydrolysis Of Cellulose And Some Factors Affecting The Production Of Cellulase In A Submerged Culture Of Alternaria Sp, Robert Murray Logan

Doctoral Dissertations

"A mile hydrolyzing procedure was utilized to degrade oak sawdust. Its capability of producing a suitable fermentatation [sic] medium was studied. In the interest of solubilizing, enzymatically, the carbohydrate portion of oak sawdust, an investigation was conducted in which various microorganisms were examined for their ability to utilize different forms of cellulose for their growth and to produce cellulose decomposing enzymes. The microorganisms included a myxobacterium, several fungi, and a wood-rotting basidiomycete. The fungi included two highly cellulolytic organisms, Myrothecium verrucaria and Trichoderma viride. The myxobacterium used was Sorangium cellulosum and the basidiomycete was Pleurotus ostreatus. The principla substrates employed …

An Evaluation Of Demonstrations On Inductor Theory, Boyd Warner Wasson

Dissertations and Theses @ UNI

The writer sought an improved approach for teaching theory of electronics to high school students. This approach was intended to require less expense and time needed to provide classroom instruction on electrical theory.

The purpose of this study were to:

(1) Prepare a number of demonstrations to illustrate phenomena associated with coils or inductors and their use in practical electronics.

(2) Prepare equipment and gather parts needed to perform demonstrations. Ease of construction and economy were important considerations.

(3) Evaluate the effectiveness of the demonstrations on student comprehension and the ability to apply information taught.

A Study Of The Work Functions Of Nigerian Industrial Technicians, Olugbenro A. Ajayi

Masters Theses

The Problem and Its Background

Introduction

A curriculum can be developed in several ways. The simplest method is to use the curriculum of another institution without modification. The hazard of such an approach lies in the possibility that the curriculum may not be a good one or, even if satisfactory for the original institution, may not fit into the conditions of the setting where it is to be used. For example, entrance requirements for institutions vary from country to country and from one institution to another.

Another method is to study a number of curriculums and develop a composite curriculum …

Transient Gamma Radiation Effects On Resistors, Harold T. Cates

Electrical and Computer Engineering ETDs

If a resistor in a circuit is exposed to a transient gamma radiation pulse, the condition of the circuit will be modified by passing from its steady state condition before radiation to a state of excitation that will depend upon the intensity and duration of the radiation pulse. When the radiation pulse is over, the circuit will then relax to its previous condition of equilibrium within a characteristic time constant.

When energetic radiation, such as gamma radiation, charged particles, or neutrons, strikes matter, it causes several effects which alter the properties of the target material. Some of the effects that …

Stresses In Thick Slabs Subjected To Thermal Loadings., Robert I. Brasier

Mechanical Engineering ETDs

The use of thick, reinforced concrete components in nuclear reactor constructions where they serve as both structural and shielding components has become commonplace. In use, the concrete ls subjected to mechanical loads due to the weight of various reactor components and thermal loads due to tempera­ture gradients and internal heating due to absorbed radiation. Since these components are required to maintain their structural integrity for long period of time under fluctuating temperature gradients their stress analysis is a vital problem. Typical components range from thick slab shields to complete reinforced con­crete pressure vessels. It is felt that current criteria for …

Antennas In Or At The Surface Of A Conducting Medium At Vlf, George R. Swain

Electrical and Computer Engineering ETDs

To meet the requirements of a number of military operations and to facilitate some types of geophysical exploration, it is necessary to communicate between points beneath or at the surface of the earth or of the ocean. This need has led to the investigation of antennas for use in or at the surface of conducting media. The purpose of this paper is to briefly survey the previous work on such antennas, to extend the concepts of effective length and other merit factors to antennas in or near a conducting medium, and to analyze the electrical behavior of the toroid and …

Simultaneous Development Of Velocity And Temperature Profiles In The Annulus With Laminar Flow And Both Walls At Constant Temperatures, Stephen Lothair Ritchie

Theses and Dissertations

Forced convection heat transfer in the entrance region of tubes and ducts has been studied extensively since the pioneering work of Graetz. Most of the published solutions for axial flow heat transfer are based on the idealization of either fully established or uniform velocity profiles with developing temperature.

Analysis And Discussion Of The Effect Of Heat Loss From The "Insulated" Face Of Thin Foil Heat Flux Meters, Mont Johnson Stevens

Theses and Dissertations

The object of this work was to investigate the effect that heat losses from the "insulated" face of thin foil heat flux meters has upon the sensitivity of heat flux meters. In the past it has been characteristic of any analysis done on heat flux meters to assume that the insulation on the back face of the foil was a perfect insulator and thereby neglect the effects of heat losses from this "insulated" face. It is hoped that the information given in this thesis will be of value in determining how the geometric and heat transfer parameters affect the operation …

Investigation Of Aerodynamic Hysteresis, Gerald Heber Peterson

Theses and Dissertations

The word hysteresis is derived from a Greek word meaning "to lag 'behind". As specifically applied to fluid flow around bodies with transient angles of attack in and near the stall region, "aerodynamic hysteresis" is used to describe the effect of delay in boundary layer separation and reattachment upon the lift, drag and pitching moment. Experimental work done on airfoils by H. Studer showed that for increasing angles of attack flow "separation is delayed to an angle of attack appreciably greater than that for a stationary airfoil. On the return movement, re-establishment of a smooth flow is also delayed." [1]* …

An Experimental Determination Of Ultrasonic Wave Velocities In Plastics As Functions Of Temperature, Ned D. Arnold

Electrical and Computer Engineering ETDs

This thesis reports the results of an experimental investigation into the effects of temperature on the velocity of ultrasonic longitudinal acoustic waves through various plastics.

Design Of Regeneratively Cooled, High Temperature, Clean Gas Plasma, Roger Carver Bartlett

Theses and Dissertations

The objective of this thesis was the design of a regeneratively cooled, high temperature, clean gas plasma generator facility. This facility was desired to extend the high temperature research capabilities of the Department of Mechanical Engineering.

Reliability Of Aircraft Altitude Estimates By Ground Observers, Euegene W. Benson

Masters Theses

No abstract provided.

The Driving-Point Impedance Of An Electrically Short Cylindrical Antenna In The Ionosphere, William E. Blair

Electrical and Computer Engineering ETDs

1.0 Since the advent of satellites, there has been con­siderable interest in both military and peacetime uses of satellites as research instruments, communication relays, and transportation vehicles. In most cases, it is necessary to communicate with the satellites for purposes of trans­mitting and receiving information.

An Oxidation Of Para-Nitrotoluene, Albert Edward Meisinger

Theses

The original purpose of this paper was to investigate the reaction kinetics of the air oxidation of para-nitro-toluene (PNT) to para-nitrobenzoic acid (PNBA). The reaction was to be carried out at atmospheric pressure and at temperatures between 100 and 175° C, and in the presence of an oxidation catalyst. However the main problem became one of trying to find a catalyst that would work at these conditions. The catalysts used were nickel acetate, cobaltous acetate, manganous acetate and manganese naphthenate. Hydrogen peroxide was tried as an accelerator for the reaction. None of these worked since no yield greater than 0.01% …

The Reaction Of Urea With Primary Alkyl Bromides, Ronald Lewis Stabile

Theses

The reactions between urea and the primary alkyl bromides from 1-bromobutane to 1-bromooctane were investigated. The effect of concentration, temperature, and solvents on the yield was determined. Second order reaction rate constants at temperature of 80°, 100°, and 132°C were calculated from the data for yield. The yield is defined as the percent of bromine from the alkyl bromide titrated as bromide ion.

The results indicate that the reactions of the primary alkyl bromides with urea are similar; the reaction being of the second order and the ex. tent of reaction being approximately the same for each alkyl bromide for …

Thermodynamic Properties Of Perfluoropropane, Frank Fang

Theses

The thermodynamic properties of perfluoropropane (octafluoropropane) have been determined by the author for the saturated region from -100°C to the critical temperature, 71°C. Properties in the superheated region were likewise determined by the author for temperatures from -35°C to 300°C and over a pressure range from 1 atmosphere to 40 atmospheres. Enthalpies, entropies, densities, and specific volumes are reported for both vapor and liquid phases where applicable. The datum point used in these calculations is based on a zero value for vapor enthalpy and vapor entropy at -100°C and 0.0183 atmospheres.

Constants used in the Benedict-Webb-Rubin equation of state were …

Amination Of Alkyl Halides, Frank Joseph Stulb

Theses

The possibility of aminating alkyl halides with urea was the prime interest of the research undertaken in this thesis. Alkyl halides and urea react only to a slight degree. However the reaction is rapid when dimethylformamide is used as a solvent.

In working with compounds containing halogen on the aromatic ring we always found the halogen to be replaced by the amino group. With alkyl halides, however, this was not so. In the case of the reaction between an alkyl halide and urea in a solvent, a compound of composition close to that of a di-alkylurea was isolated and the …

Application Of Radioactive Tracers In The Study Of Diffusional Phenomena, Rodolfo Cilento

Theses

The study of mass transfer of a solute through a solvent can be greatly facilitated by the use of radioactive tracers.

This experiment was developed to demonstrate that by using radioactive tracers very small quantities of matter that would be very difficult to test chemically, can not only be tested but easily followed without disturbing the apparatus in which the diffusion is taking place.

Oleic Acid tagged with radioactive iodine (I¹³¹) was diffused through hexane at constant temperature in a glass column, one inch in diameter and thirty-six inches long.

The diffusion of Oleic Acid was followed by …

Decomposition Of Diacetone Alcohol In Packed Beds Of Ion Exchange Resins, Arthur Donald Lahr, Rafael Juan Puente-Duany

Theses

A study was made of the rate of decomposition of diacetone alcohol by anion exchange resins in a packed bed under adiabatic and isothermal conditions. Two different resins were compared: a conventional type gel structure resin, Amberlite IRA-400, and a newly marketed maorore-ticular resin, Amberlyst A-26.

In a substrate with low water content, the rate of decomposition of diacetone alcohol by Amberlite IRA-400 vas controlled by intraparticle diffusion. This vas due to shrinkage of the polymer chain matrix of the resin. When dry diacetone alcohol feed was introduced the amount of decomposition was not measurable.

It was found that the …

Interphase Gas-Liquid Mass Transfer Study In A Horizontal Channel, Bruce R. Marx

Theses

The rate of transfer of hydrogen sulfide and of carbon dioxide from an atmosphere of the gas saturated with water to a flowing stream of water in a horizontal channel was investigated over a range of water flow velocities and absolute pressures.

Mathematical models describing the system in terms of the penetration and boundary layer theories were inadequate when used to calculate the diffusivity of each gas in water at various conditions. The results of the hydrogen sulfide-water system study shows a relationship between the diffusivity, the interfacial concentration and the liquid flow rate. The calculated diffusivity of the carbon …

Esterification Of Oleic Acid, Niranjan Muljibhai Patel

Theses

The purpose of this paper is to determine the effects of catalyst concentrations and temperatures on the rate of reaction and energy of activation in the reaction system of oleic acid and oleyl alcohol. It is suggested by Flory^2,3 that the p-toluene-sulfonic acid catalyzed esterification reactions follow a second order mechanism. The p-toluene-sulfonic acid is used in the present work.

Two different catalyst concentrations were used at two different temperatures. The uncatalyzed reaction at the same temperatures was also studied. The specific rate constants are calculated and from that, the energy of activations are calculated using the Arrhenius equation. …

Diffusion Of Single And Multicomponent Solutes From Capillaries, Oleh S. Sklepkowycz

Theses

The purpose of this investigation was to determine the diffusion coefficients of several single and multi-component solutes, and to establish the relations between the diffusivity, the solute composition) and the diffusion rate. Such information pertinent to the extraction and leaching operations, can not be found in literature.

The procedure developed by Piret, Wbel, and Armstrong (25), involving observation of the extraction rate of two-phase mixtures from straight capillaries, was adopted and verified on a known sodium chloride-water system.

In the course of the experimental work diffusion coefficients more determined for ursolic acid, palmitic acid, and tripalmitin in methyl isobutyl ketone. …

Gas Phase Fugacity Coefficients, Harvey Joel Klee

Theses

A method is presented for calculation of fugacity coefficients in gas mixtures. This work is based on a recent paper by Leland, Gamson, and Chappelear, wherein they presented a new method for evaluation of ideal K values. The information required for the method presented here includes pure component physical properties, and generalized tables or equations for compressibility factors, fugacity coefficients, and real gas enthalpy departure terms. Pseudo-critical temperatures and pressures for the mixture are calculated using the expressions presented by Leland and Mueller.

Five different binary systems consisting of paraffin hydro-carbon and CO₂ mixtures containing 318 separate points were …

Effect Of Temperature On Rate Of Absorption Of Ammonia By Water In Packed Tower, Chhotu B. Patel

Theses

Measurements of the rate of absorption of ammonia in water have been made using a 4-inch diameter Lucite column With porcelain Raschig rings packed to a height of 3 feet, Tests were made with water rates of 462 and 695 lbs./ hr-ft² and a constant gas rate of 130 lbs/hr-ft² with liquid temperature verying from 72° F. to 110° F.

At constant liquid and gas rate, the mass transfer coefficient, Κ_Ga, decreases with increasing liquid temperature and in represented by straight lines on plot of Κ_Ga versus temperature. The variation of Κ_Ga …