Engineering Commons^™

An Intensity Regulation System For A Monochromator, David A. Wayne

Masters Theses

"In the investigation of phenomena involving both optical intensity and wavelength, an instrument is often desired which allows one of the quantities to be held constant while the other is varied. A relatively inexpensive system is described which utilizes a commercial grating monochromator and external feedback electronics to regulate the output intensity as the wavelength is varied. In this system, a sample of the output intensity is taken by a photosensor with known spectral response. The output of the photosensor is then compared electronically with that of a pre-programmed function generator which cancels nonlinearities in the photo-sensor. The resulting signal …

The Modeling, Fabrication, And Testing Of An Instantaneous Torque Measuring System, Thomas Phillip Hertel

Masters Theses

"The purpose of this work was to obtain a measuring system to experimentally determine the instantaneous magnitude and frequency of the torques from zero to 2400 Hertz produced by a single phase motor. This paper explains the methods employed in designing and fabricating a measuring system and shows the results from tests using this equipment. It was found that a measuring system based on the determination of the instantaneous value of the stator's reaction torques could be realized. Also, it was found that some simple methods of computation could be used to find the magnitudes of the frequency components comprising …

Determination Of Molecular Diffusivities In Liquids, Pai-Chuan Wu

Masters Theses

"A porous plate, initially at a uniform solute concentration is immersed in a well-stirred pure solvent bath of known volume. It is desired to find the molecular diffusivity of the solute-solvent system by observing the change of the solute concentration in the solvent bath with time. In this study, concentration-time data were curve-fitted by non-linear, least squares techniques to the various mathematical solutions describing molecular diffusion in the porous frit. This technique is used to determine the diffusion coefficient and predict the value of other parameters existing in the different mathematical diffusion models. The results from the different models are …

Impulse Response Of Rc Exponential Lines, Oscar Gojon

Masters Theses

"This thesis presents an application of the analysis of the n-wire exponential line to the case of the 3-wire RC exponential line terminated in its characteristic impedance, and to the 2-wire exponential line with open and short circuit terminations. These lines are excited with Δ-function voltage generators, and the corresponding impulse responses are obtained"--Abstract, Page ii.

Liquid Extraction With Single Droplets-Effect Of Chemical Reaction, William Victor Andoe

Doctoral Dissertations

"The circulating drop mass transport model based on Hadamard's dispersed phase stream function was solved numerically to account for a solute diffusing into a droplet and undergoing a first order irreversible reaction with the drop medium for the case where the continuous phase resistance to solute transport is negligible ... Experimental data were obtained for a system which consisted of 2-chloro-2-methylpropane (t-butyl chloride) diffusing from a benzene continuous phase into falling water droplets and undergoing a first order irreversible reaction with the water droplets ... The experimental solute transport rates were a factor of 7 to 10 greater than those …

Recombination Statistics For The Neutron-Induced Base Current Component, Ming-Chwan Chow

Doctoral Dissertations

"This paper presents a derivation of the recombination statistical model for the neutron-induced base current component. The derivation was based on the assumptions: 1) the current equation for the induced current component developed by Goben is valid; 2) the Shockley-Read-Hall statistics for holes and electrons are applicable; and 3) the recombination statistics derived by Sah, Noyce and Shockley, for sites in the bulk space-charge region are valid. Several examples were presented to emphasize accuracy of this derived model for predictions. This paper shows that the recombination process may be described by a mathematical model, recombination statistics which depend on the …

Surface Self-Diffusion On Nickel (111) By Radioactive Tracers, James Ronald Wolfe

Doctoral Dissertations

"Surface self-diffusion coefficients have been measured by a radioactive tracer method over the temperature range 614⁰ to 840⁰C on nickel (111) surfaces characterized by LEED. Previously unrecognized tracer evaporation during surface diffusion resulted in restricted spreading of the tracer at higher temperatures. A theoretical treatment of the tracer evaporation phenomenon is presented and subsequently used in the analysis of the data. The temperature dependence of the surface self-diffusion coefficient (D_s) for nickel (111) can be represented, over the experimental temperature range, by a single Arrhenius type relationship...Arguments are presented to justify an adatom surface diffusion mechanism which is …

Design Of A Sequential Detector, Scott William Abel

Masters Theses

"The communication engineer has in the past treated the detection problem from a limited point of view. Detectors have been designed to reach a decision based on a specified number of samples. This approach has proved valuable, but it offers no provisions for an early decision if a conclusion becomes obvious early in the sampling. Neither is there an opportunity for additional sampling if necessary to reach a definite conclusion, because of these limitations it is desirable to find more general detectors. This study looks at a specific statistics (the sign test) and designs a sequential detector to utilize this …

Semiempirical Determination Of The Differential Fast Flux Spectrum For U-235 Fission With Water Moderator, Henry Anthony Till

Masters Theses

"The differential fast flux spectrum of the UMR Pool Research and Training Reactor core was determined by simultaneous activations of threshold foil detectors by neutron-nucleon reactions. This represents one phase of the composite neutron environment at two sample irradiation locations and the center of a fuel element during a power operation of 200 Kw (th). To accomplish this measurement a semiempirical least-squares approximation fitting activation date to a theoretical Cranberg U-wet fission spectrum was applied. This is a technique designed specifically for water moderated systems and takes into consideration both virgin and down-scatter neutrons. Gamma decay photopeaks were reduced using …

Shear Strength Behavior In Silts And Clay Mixtures, Alan T. Jackson

Masters Theses

"A series of consolidated undrained triaxial tests with pore pressure measurements were performed on laboratory sedimented samples having various known silt to clay content ratios. The clay used was commercial grundite clay from Goose Lake, Illinois, and the silt used was extracted from Lebanon Silt Loam from Rolla, Missouri. Silt was mixed with clay in the following percentages by weight: 0%, 20%, 40%, 50%, and 80%. Results indicate an increasing angle of internal friction with an increase in silt content. The unconfined compressive strength of the samples remained constant, as would be expected in a clay, with increasing silt content …

Pressure Welding Of Continuously Cast Nodular Iron, Gerald W. Wille

Masters Theses

"The objective of this study was to determine the feasibility of using pressure welding as a joining technique for swaged nodular iron.

Test pressure welds were produced with swaged continuous cast nodular iron at temperatures between 1750⁰F and 2050⁰F with welding pressures between 15,900 psi and 51,400 psi using an induction coil to heat the weld zone.

Pressure welds of greater strength than the as-received nodular iron were produced by swaging the material before welding. The optimum welding parameters were a temperature of 2050⁰F with a welding pressure of 46,700 psi.

On the basis of these tests it is concluded …

Synchronization Of Pulse Code Modulation Telemetry, Lawrence J. Mueller

Masters Theses

"Pulse Code Modulation (PCM) is one of the most widely utilized radio telemetry techniques for the recovery of test data from aerospace vehicles. Synchronization of the receiver with the transmitted data is perhaps the prime requisite of a PCM telemetry system. In this paper the frame synchronization process is analyzed by developing equations which define the three modes of synchronizer operation (SEARCH, VERIFY, and LOCK) in terms of the relative probabilities of operation. The criteria employed to optimize the synchronization process are the mean time to acquire true synchronization, the probability of true synchronization after verification of the synchronization decision, …

A Computer Adaption Of Plastic Analysis For Rigid Frames, Gerald Duane Galloway

Masters Theses

"A computer program for the plastic analysis of rigid frames is presented. The program is based on the virtual work method of plastic analysis. The great number of failure mechanisms that must be considered in any virtual work analysis are given in Appendix C. The use of the program as a design aid is also discussed. A check for the virtual work program is also presented. The check is based on the method of inequalities as initially presented by Symonds and Neal"--Abstract, page ii.

The Inert Gas Effect On The Rate Of Evaporation Of Zinc And Cadmium, Chu Sheng Wu

Masters Theses

"An experimental study has been made to investigate the effect of argon and helium on the rate of evaporation of zinc and cadmium under one atmosphere pressure at temperatures ranging from 500⁰C to 850⁰C. The experimental results were compared with the maximum rates calculated using the effusion formula as well as with values obtained using three different types of equations based on kinetic theory, diffusion theory, and empirical data. The rate of evaporation in this study appeared to be diffusion controlled. Equations have been derived for expressing the rate of evaporation of zinc and cadmium in both argon and helium …

Evaluation Of Methods For Analysis Of Multi-Degree-Of-Freedom Systems With Damping, Brijgopal R. Mohta

Masters Theses

"A general review of various methods for studying the behavior of linear lumped parameter systems with viscous damping is presented. Five methods are discussed. These are: (1) Normal Mode Technique (2) Ho's Method (3) Impedance Method (4) Graphical Technique (5) A Method for Reducing Degrees-of-freedom. For solution of vibration problems by the Normal Mode Technique, the systems are classified as (1) classically damped or (2) non-classically damped. It is shown that the classically damped systems are relatively easy to solve. For non-classically damped systems, the method proposed by K. A. Foss has been employed. This method is quite complex, but …

Measurement Of Demagnetizing Factor Of Ring-Core, Subhashchandra Chimanlal Patel

Masters Theses

"A method has been presented to measure the demagnetizing factor of ring-cores. First the incremental apparent permeability and the incremental true permeability were measured at different degrees of saturation and then the demagnetizing factor was determined from those results. The cores used were tape would ring-cores of mean length of 8.0 cm. The method was found suitable for cores with 1/4 mil or thicker tape, but was in question for the 1/8 mil tape core tested"--Abstract, page ii.

Estimation Of Film Boiling Heat Transfer Coefficients For Cylindrical Heaters In Corresponding States Fluids, Gary Joseph Capone

Masters Theses

"An investigation of film boiling heat transfer was made with cylindrical heaters. The (0.75" O.D.) gold plated, copper heaters were positioned horizontally in pools of liquid argon, nitrogen, and carbon monoxide. A correlation for film boiling corresponding states fluids is derived and discussed. The correlation is a least squares fit of three variables: the diameter of the cylindrical heater, the reduced pressure of the system, and the temperature difference between the heater surface and the saturated pool"--Abstract, page iii.

Analytical And Experimental Methods For Determining The Properties Of Materials At Very High Rates Of Loading, A. G. Behring

Masters Theses

"In the following report, some of the properties of ALCOA 7075 T651 aluminum, when subjected to high rates of loading, are experimentally investigated by impacting two rods of the material longitudinally. One rod is accelerated to a uniform velocity with an air gun launcher. The stationary second rod is instrumented with strain gages on its lateral surface in order to determine the strain-time history following impact. A detailed description of the experimental equipment is included. Simple, one-dimensional theory is used to determine the dynamic, elastic modulus of the test material under the impact condition. Several observations regarding the behavior of …

The Design Of A Molten Fueled, Vortex Reactor, For Use As A Rocket Propulsion Device, Robert Philip Schmitt

Masters Theses

"The purpose of this investigation is to design a nuclear reactor which can be used as a rocket propulsion device. The reactor investigated is fueled with a molten uranium-bismuth alloy and utilizes a two phase vortex flow principle. Hydrogen is employed as a coolant and rocket propellant. The hydrogen is heated directly by the fuel thus eliminating the need for heat exchangers. The major part of the investigation consists of a two group neutron diffusion study to show the operational feasibility of this type of reactor and to obtain an optimum design. the study shows that this type of reactor …

Scattering Parameter Measurements And Amplifier Design, Thomas J. Herrick

Masters Theses

"The scattering parameter formulation in describing the small-signal operation of an active two-port device is developed. The inherent advantages of measuring the scattering parameters at UHF frequencies and the clear insight into the design problem are demonstrated. Some of the practical difficulties in a typical design problem are also considered"--Abstract, page ii.

Engineering Properties Of Bloomington-Normal Subsoils, Rohn Dunseth Abbott

Masters Theses

"The glacial subsoils of the Bloomington-Normal, Illinois area have been analyzed with regard to their engineering properties. Several boring logs are included to illustrate the horizontal and vertical variability in soil units encountered and in the engineering properties of these soil units. The engineering properties of the two most common foundation soils, the Bloomington and Normal tills are compared and special consideration is given to evaluating the compressibility of these materials. Evidence is presented that indicates that the circumferential trimming of a highly preconsolidated soil containing stones can cause significant sample disturbance. Special sampling techniques which eliminate circumferential trimming yield …

The Design Of A Hybrid Computer System, James Joseph Becker

Masters Theses

"Three typical hybrid computers in industry and educational institutions are presented. The hybrid computer designed and built at the University of Missouri at Rolla consists of an SCC-650 digital computer, a TR-48 analog computer, and a hybrid interface. The interface permits the digital computer to control the modes of operation on the analog computer. There are also 9 multiple-pole relays on the interface that can be controlled by the digital computer. A 320 hold removable patchboard is included in the interface. There are 40 trunks lines from the analog computer that are present on the patchboard. The 4 digital-to-analog channels …

The Design Of A Tape Deck Controller, Frederick Harold Keeve

Masters Theses

"A controller was built to interface the SCC-650 general purpose digital computer and the Kennedy Model 1400R incremental write/continuous read tape unit. All logic design information, signal lists, and tape deck instructions are included"--Abstract, page ii.

Construction Time And Cost Control Using The Ibm Project Management System/360, James Donald Bailey

Masters Theses

"The object of this investigation was to determine the advantages or disadvantages involved in the use of the IBM Project Management system/360 as a time and cost control tool as compared to the methods presently used by construction contractors in the small to medium size range.

The methods used by three construction contractors were investigated in order to acquire a sample of methods presently used.

It was determined from the investigation that a number of advantages could be obtained which would provide better control of a construction project.

It was also decided that a detailed investigation concerning the cost of …

A Numerical (Matrix) Solution For The Vibration Frequencies And Modes Of A Nonuniform Rectangular Plate With Arbitrary Edge Conditions, F. David Utterback

Masters Theses

"The material presented in this thesis is designed to provide the practicing engineer with a practical, approximate method of solution for the increasingly important problem of plate vibrations. The technique presented herein is basically an application of the use of generalized coordinates to describe the elastic and inertial properties of a finite element representation of a nonuniform rectangular plate. The plate will be idealized by utilizing a modification of the grid work technique developed by Hrennifkoff as a lattice work of interconnecting beams. By employing the elastic displacements as generalized coordinates, the only required compatibility conditions are that the displacements …

The Numerical Solution Of Two-Dimensional Fluid Flow Problems, E. David Spong

Masters Theses

"A numerical solution method is developed for the solution of two-dimensional, irrotational and compressible fluid flow problems. The partial differential equation, in terms of the velocity potential, describing the flow is replaced by finite difference equations and the resulting matrix is solved by Gaussian elimination. The method is successfully applied to two subsonic flow problems: a 7.5⁰ wedge and a 6⁰ wedge inlet. The method becomes invalid, as expected, with the appearance of sonic velocity in the flow field. An investigation of the definition of the singularities is made. This indicates that the best agreement with the experimental results for …

Sufficiency Conditions For Constrained Optima, Cheng-Chun Huang

Masters Theses

"The sufficiency conditions for constrained optimization problems are derived through the use of Lagrangian functions and through the introduction of the new concept of "constrained total derivatives." The relations can be used with equality and/or inequality constraints. The sufficiency conditions derived earlier by Phipps were corrected in this work--Abstract, page ii.

Distillation Column Simulation And Control, Hsian T. Chao

Masters Theses

"A 5-component, 10-stage distillation column was simulated by PACTOLUS by use of the hybrid technique. It was found that the digital-analog simulator is completely satisfactory for solving unsteady-state multicomponent distillation problems. A feedforward controller for a distillation column was designed and tested. The effects of feedforward and feedback control on binary system distillation columns were compared by PACTOLUS. It was found that the liquid flow rates, the holdups as well as the number of stages are important factors in the design of a feedforward controller"--Abstract, page ii.

A Study Of Swirling Air Flow In A Converging Nozzle, Charles William Lineberry

Masters Theses

"A study was conducted to determine the behavior of swirling air flow in a converging nozzle. Special instrumentation was constructed to obtain radial traverses of the flow at four axial positions. the data collected consisted of velocity, static pressure, and stagnation temperature. The flow pattern demonstrated the Ranque-Hilsh effect and reversed axial flow in the core region. As the flow entered the nozzle, it had the characteristics of a free vortex. At the exit plane the characteristics were those of a forced vortex. The converging nozzle caused an increase in the magnitude of the axial velocity component"--Abstract, page ii.

An Experimental Method Of Determining The Thermal Accommodation Coefficients Of Metallic Surfaces, Raymond John Dethorne

Masters Theses

"In the free molecule regime, Knudsen number greater than 10, heat is transferred from a solid by radiation and conduction. The ability of a surface to emit radiant energy is governed by a surface property called emittance while the surface property which apparently regulates the amount of heat transferred by conduction is called the thermal accommodation coefficient. This thesis presents the results of an experimental investigation to determine a relationship between these two properties, emittance and thermal accommodation coefficient. A test apparatus was constructed to measure both the radiation and conduction contributions between two concentric cylinders. cylinders of aluminum and …