Engineering Commons^™

The Development And Testing Of A Fluidic/Pneumatic Position Servo, David Lyle Portin

Dissertations and Theses

This thesis reviews the design and analysis of a fluidic/pneumatic position servo. Rolling diaphragm piston actuators are used for the system drive, and a hydrostatic gas journal bearing is used as the position sensor. The servo has a 1 inch range which is monitored using an electrical capacitive position transducer that was built as an integral part of the system.

Open-loop frequency response testing provides the basis for a mathematical model of the system.

The servo response is linear at frequencies up to 3 Hertz.

The frequency response appeared to be limited by the design of the gas bearing sensor, …

Error Codes In Digital Data Communication Systems, Robert Hadley Cravens

Dissertations and Theses

Today’s digital communication systems perform data transfers at the rate of millions of bits per minute, with data errors in the order of 1/6th error per day. This magnitude of errorless communication is now possible because of sophisticated error correcting codes. Many types of error codes are employed today in three distinct areas of digital data communication: human to computer; data source to computer; computer to computer; and intra-computer; we are concerned here with intra-computer communication.

This research is primarily a mathematical study of error codes in general to explore the possibilities of each major type for the purpose of …

Study Of A Thin Wire Monopole Antenna Mounted On A Finite Cone, Fwu-Jih Hsu

Electrical and Computer Engineering ETDs

Theoretical and numerical considerations of the boundary value problem involving radiation from a monopole thin wire antenna mounted on a finite cone are investigated. The problem is handled in a generalized format using Green's dyadic functions which are appropriate to the geometry of the system. The methodology of handling numerical sets of integer order, as well as real order, orthonormal eigenfunctions is developed with particular emphasis on the rapid convergence in order to be acceptable with available computer facilities. The truncation error involved in such problems is checked by observing the continuity conditions, and a parametric study then follows. Agreement …

Separation Of Organic Solutions By The Indirect Fractional Solidification Process With In-Situ Washing And Melting Operations, Juiuun-Perng Chiang

Chemical and Biological Engineering ETDs

The main objective of the present thesis study is to experimentally investigate the feasibility of purifying both dilute and concentrated organic solutions by the indirect freezing process with in-situ washing and melting operations under industrially practicable operating conditions. The smooth deposit approach and the dendritic deposit approach are respectively used in separating dilute solutions and concentrated solutions and small ΔT's for heat transfer, less than 3 °C, have been used throughout the study.

A convenient ultrasonic device and easily practicable operating procedures for nucleating slightly super-cooled liquids have been developed. Several freezer­melter systems incorporating the new ultrasonic devices have been …

Limit Design Of Unbraced Reinforced Concrete Frames, Thomas Joseph Gavin

Dissertations and Theses

The main objective of this study was to determine whether Limit Design could be applied to low-rise unbraced concrete frames. The investigation was carried out both analytically and experimentally.

In the analytical part, two mathematical models were used to determine the behavior of unbraced frames. The first method used a nonlinear computer program, which takes into account the material and geometric nonlinearities of concrete frames. Several cases of frames with different reinforcement ratios and under different beam to column load ratios were investigated. For each frame the gravity loads were increased proportionately to 3/4 of the ultimate frame capacity. Then, …

Static Temperature Measurements In Supersonic Flow Using Lasar Raman Spectroscopy, Paul A. Nystrom

Mechanical & Aerospace Engineering Theses & Dissertations

Laser Raman spectroscopy is a nonintrusive technique which can generate mean static temperature (MST) data within flow fields. By ratioing two simultaneously gathered portions of the Raman scattered spectrum, absolute intensity measurements were not needed. This method was applied to a supersonic cold air jet, where the NST ranged from 160'K to 300'K. Accurate measurements were not realized due to the presence of flow contaminates, especially water vapor.

Optimal Control Of A Large Space Telescope Using An Annular Momentum Control Device, Arun Anant Nadkarni

Mechanical & Aerospace Engineering Theses & Dissertations

Application of a new development in the field of momentum storage devices, the Annular Momentum Control Device (AMCD), to the twin problems of large angle maneuvers and fine pointing control is considered. The basic concept of the AMCD consists of a spinning rim, with no central hub area, suspended by a minimum of three magnetic bearings, and driven by a noncontacting electromagnetic spin motor. The dissertation considers in detail the design of an optimal controller to achieve both large angle maneuvers and the fine pointing control of a Large Telescope (LST) with a single configuration, consisting of a single AMCD …

A Fast Boundary Tracking Alogorithm For Constrained Nonlinear Mathematical Programming Problems, Jacob Yaghoub Moradi

Dissertations

A fast search algorithm for the solution of nonlinear mathematical programming optimization problems is presented in this thesis. A gradient search procedure is combined with a "Boundary Tracking"(BT) method using the feasible direction finding method of Zoutendijk for generating a feasible starting direction along the feasible-infeasible boundary.

The algorithm is applied to the minimum weight design of submersible, circular, cylindrical shells reinforced by equally spaced "T" type frames. This problem had produced algorithm failure in two earlier studies and was only recently solved by the Direct Search-Feasible Direction Algorithm (DSFD) which was shown by recent comparison studies to be among …

The Separation Of Proteins Via Parametric Pumping And Ion Exchange, Paul Albert Falcon

Theses

A pH parametric pump, coupled with ion exchange, was used in an experimental investigation to separate a protein-water binary mixture. The model system consisted of a hemoglobin-water binary mixture. A pH gradient throughout the parametric pumping column was sustained with the use of hollow fiber devices incorporating phosphate buffer circulation.

Data is presented for both batch and semi-continuous recuperative mode pH parametric pumping. Continuous pH parametric pumping for protein isolation has also been envisioned.

No attempt has been made to optimize this newly devel-oped process; however, certain parameters are suspected of controlling separation, including buffer concentration, half cycle time, packed …

The Settling Of Particles In A Square Contained Medium, Richard S. Matyas

Theses

Stokes' Law, has been standardly utilized to calculate the terminal velocity of falling particles. However, the limitation of Stokes' Law is that it does not take into account the container walls and their resulting drag forces. Extensive work with additional drag due to cylindrical container walls has been examined by many investigators. The classical and earliest is the well know Ladenburg Correction which cannot be utilized with non-cylindrical containers. This experimental thesis examines the analog of the Ladenburg relationship for a square container. This experimental thesis was undertaken to experimentally determine the value of the constant K₁ for a …

Nonlinear Buckling Of Deep Cylindrical Shell Panels With Imperfections, Madhusudan H. Jhaveri

Dissertations

The work presented in this dissertation is devoted to the analysis of nonlinear buckling of thin cylindrical shells with imperfections. The nonlinearity of the problem treated in this dissertation is that associated with large displacements in the linear elastic range. The method used is not restricted by the magnitude of the displacements provided that the strains do not exceed the limit of proportionality.

Thus, based upon the large deflection theory, cylindrical shell panel is investigated for buckling under the action of uniform external pressure. Certain higher order infinitesimal terms which are usually neglected in the shallow shell theories, have been …

Flow Of Polymer Melt Blends Through Porous Media, James Atwood Parker

Dissertations

The flow of molten polystyrene, poly(methyl methacrylate) and three blends of these polymers has been studied in a rheogoniometer and in packed beds of unconsolidated spherical glass beads. One primary purpose of the study was to determine the behavior of polymer melt blends in porous media flow. The second major purpose of the work was to develop and test a new and powerful model for packed bed flow based upon the Huang generalized rheological constitutive equations.

Rheological characterization of the pure polymers and blends was obtained using a Roberts-Weissenberg rheogoniometer. Shear and normal stresses were measured at shear rates from …

Acoustical Holography By Holographic Interferometry, Amin Mohamed Hanafy

Dissertations

The ability to "see" with sound has long been an intriguing concept. It is apparent that ultrasonic energy can give an image of an object not obtainable with light or even with x-rays.

In this dissertation, a novel "three-step acoustical holographic imaging system" is described and several means for its implementation are analyzed. A novel holographic acoustic image converter, which constitutes a fundamental link in the three step imaging method was also developed. The use of optical holographic techniques to convert an arbitrary acoustic image to a visible image is conducted and resulted in the introduction of the new technique …

Analysis Of Combustion Products Of Kynol And Nomex, Abdul Halim Hassan Housny

Theses

The gaseous products generated by flaming combustion of Kynol and Nomex fibers under the same conditions (temperature 300-700°C, natural air) were quantitatively analyzed by infrared spectrophotometry, gas chromatography, mass spectrometry and a colorimetric tube method. The four techniques were chosen to examine the wide range of volatile and condensable products expected due to their different capabilities and sensitivities.

The main gases generated were carbon monoxide, carbon dioxide, methane and benzene.

The mass spectrometer was used to identify the condensed vapors. These were mainly phenol, methyl phenol and dimethyl phenol from the Kynol fiber and benzene, aniline, diaminobenzene, benzoic acid, benzonitrile, …

The Effect Of Ultrasonic Vibrations And Catalyst Particle Size On The Decomposition Of Cumene, John F. Pietranski

Theses

The effect of ultrasonic vibrations on the vapor phase decomposition of cumene to benzene and proplyene was investigated using silica-aluminum as the cracking catalyst.

The system consists of a tubular reactor with a 4 inch long catalyst chamber made from 1 cm. diameter stainless steel tubing. The catalyst bed was irradiated from above by means of an ultrasonic horn.

The reactor was run at temperatures of 850 to 950°F., frequencies of 26,000 and 39,000 Hz, with a power innut of 0.30 watts/cm.² . Feed rates of 100 to 300 gms./hr. and catalyst particle sizes of 0.0209 to 0.358 cm. …

Non-Equilibrium Parametric Pumps For Separating Liquids Or Gases, Anil Krishna Rastogi

Theses

An experimental and theoretical study has been done of Non-Equilibrium parametric pumps. Mathematical models and computer programmes are developed for both thermal and heatless parametric pumps based on non-equilibrium conditions and linear isotherms. A mathematical study was done for thermal parametric pumps whereas both experimental and theoretical studies were made for a heatless parametric pump. The effect of different operating conditions has been investigated on the separation of NaCl-H₂O via a thermal parametric pump and He-CO₂ and He-C₃H₆ gas mixtures via a heatless parametric pump.

The experimental study of heatless parametric pumps was extended …

Vapor-Liquid Equilibrium At Low Pressures : Correlation Of Binary And Prediction Of Multicomponent Data, Norman I. Silverman

Theses

The Wilson equation is chosen as typical of the new correlations for activity coefficients gaining wide distribution for use in the correlation and prediction of vapor-liquid equilibria today. Vapor liquid equilibrium data for 247 binary systems have been regressed against each of ten (10) objective functions and values of the Wilson energy parameters obtained. For the typical binary system, a wide variation of the Wilson energy parameters are observed when different objective functions are used with the given set of binary data. These are each examined with respect to their capability to correlate multicomponent vapor-liquid equilibrium data for seventy-three (73) …

An Approach To Energy Conservation In A Manufacturing Industry, William Polignano

Theses

The approach attacks the problem of control and planning of energy usage via three major categories. These areas are: detection, forecasting and reporting of energy usage.

To initiate any energy program the first step, is the identification of the areas that use the most energy, thus allowing detailed studies to be concentrated in these energy-intensive areas. The author has attempted to show which areas are energy-intensive in his employer's plants.

The second step is the accurate forecasting of energy usage. The author has attempted this via an econometric forecasting model that accurately predicts energy usage based on direct labor hours …

Point Of Operation Safeguarding - A Metal Forming System Approach, William Baker Eaton

Theses

The mechanical power press in its application in the metal stamping and forming industry has been misinterpreted as a selfcontained metal forming system. Examination of the production routines involving the press show that this machine is actually only one elemental component of the metal forming system and not the total production unit.

Authoritative codes and standards pertinent to the mechanical power press have reflected this misinterpretation by not including system considerations in their contents. These omissions have resulted in the providing of safeguards which do not properly reflect the particular characteristics of the metal forming system to which they are …

The Guarding Of The Principal Metalworking Machines : The Techniques, Need, And Responsibility, Peter James Schwalje

Theses

This thesis examines the guarding of the principal metalworking machines employed in the economy. The machines selected for consideration comprise the bulk of metal processing equipment utilized in the basic fabrication and manufacturing processes. It has been intuitively recognized that this equipment has been involved in a significant quantity of industrial accidents by the very nature of the hazards created by their normal use. Consequently, a need to develop some form of guarding or means of operator protection is called for.

In order to examine this question the principal metalworking machines are enumerated, their basic operating characteristics set forth,, and …

Growth Patterns Of Bacteria In Pressurized Sewage, Dennis Mazzei

Theses

Primary sewage was pressurized at 100 psi for one hour. The effects of this pressure on the growth patterns of general and nitrifying bacteria were examined daily for eighteen consecutive days using Standard Plate Counts and Most Probable Number (MPN) estimates. In conjunction with these tests, the degree of biodegradability was also determined by measuring both daily biochemical oxygen demands (BOD's) and dissolved oxygen levels.

Graphical analysis of experimental data compare the BOD's exterted [sic] by microorganisms to their respective numbers of colonies as determined by plate counts of both pressurized and non-pressurized sanitary sewage diluted to 3. 00%. The …

Ecuador And A Business Opportunity, Cesar Arturo Paredes Roldan

Theses

As a result of its recent status as a petroleum exporting country, Ecuador is enjoying an economic boom, which is expected to lead to the formation of new enterprises, the creation of jobs, the utilization of human and natural resources and the encouragement of harmonious development of the national economy.

This thesis is based on the belief that the private sector must assume a decisive role in the adequate implementation of Ecuador's industrial development programs, and it aims to show the feasibility of establishing there an enterprise that would manufacture domestic electric irons.

The coverage of the subject comprises three …

Sparsity And Decoupling In Load Power Flow Analysis, Kenneth Nazimek

Theses

This paper presents some recent ideas on and methods created by power engineers for the solution of the Load Flow Problem. Beginning with an analysis of the solution of large systems of linear equations, techniques employing elementary matrix operations are discussed to reduce the amount of calculations necessary to achieve repeated solutions. Recent interest in taking advantage of the characteristic sparsity of the admittance matrix is also examined. The problems of operating on and computer storage of large sparse matrices are investigated. Methods to efficiently order, store and work with large sparse matrices are discussed and demonstrated. The general acceptance …

Thermal Decomposition Products Of Kynol And Nomex With Reference To Structure And Toxicity, Shaker H. El-Sherbini

Theses

The purpose of this investigation was to study the combustion products of KYNOL and NOMEX as a fire retardant fibers. From the quantitative analysis data of the combustion products, the polymer structure is discussed and the property of thermal stability is explained.

From the analysis of the combustion products, the toxicity indices for the two fibers are determined. It is found to be 0.1 for KYNOL and 0.71 for NOMEX. This can be interpreted to mean that, if one gram of MIDI, is decomposed and the combustion products were diffused in one cubic meter of air, the probability of dying …

The Anisotropic And Isotropic Strength Behavior Of An Illitic Clay, Miles M. O'Brien

Theses

The cause and the nature of anisotropy in a cohesive soil was investigated by direct shear and triaxial compression tests. Laboratory techniques and procedures used to prepare isotropic clay samples are given where consolidation was accomplished under hydrostatic pressure. Direct shear tests were performed on these specimens trimmed at different inclinations to the physical horizontal from the block samples. The ratio of undrained shear strengths in any direction to shear strength in the vertical direction was found to be equal to one, proving isotropy existed. Similar tests were performed on specimens trimmed from the same clay consolidated one-dimensionally. Results from …

Dynamics Of The Glucose-Insulin-Glucagon System, Joseph P. Hartmann

Theses

A computer model for the Dynamics of the Glucose-Insulin-Glucagon System has been developed for a 17.5 kg canine using the Continuous Systems Modeling Program (CSMP) for the 360 Computer System. The major body components controlling the glucose dynamics (liver, pancreas, body muscle, blood flow, and body fluid compartments) have been modeled in terms of either their production, absorption, or transport of glucose, and the concentration levels of both the hormones and substrates perfusing the body component. A set of mneumonics has also been developed to label the hundreds of constant and variable terms required to describe a complex system of …

An Experimental Study Of Separation Of Binary And Ternary Gas Mixtures By Parametric Pumping, Stephen E. Belsky

Theses

An experimental study of gas parametric pumping is presented which examines the purification of helium using silica gel to remove the impurity carbon dioxide. Low gas flow rates are used to allow adequate time for equilibrium to be approached, assuming intraparticle diffusion is the controlling mass transfer step. By varying the cycle time, at long cycle times, the effect of penetration length (a function of dynamic capacity) is indicated. Also, at low cycle time, the effects during pressure changes become more significant.

Using low flow rate improves separation effectiveness if evaluated at equal dynamic capacity. When using low flow rate …

Air Control In A Newark City Subway Station, Robert H. Burch

Theses

During the period from June, 1974 to January, 1976, 103 24-hr samples of the air at the Broad Street station of the Newark City Subway were collected by cascade impactor. The size distributions (based on Stoke's equivalent diameters) of the total suspended particulate matter were determined gravimetrically. Samples were also analyzed by atomic absorption spectrometry to obtain information on the concentration of iron, manganese, lead, copper, zinc, and cadmium in each size fraction. The geometric mean particulate level was found to be more than twice the Federal Ambient Air Quality Standard and triple that of ambient Newark air sampled nearby. …

An Experimental Investigation Of Unbraced Reinforced Concrete Frames, Nourollah Samiee Nejad

Dissertations and Theses

The main objective of this investigation is to study experimentally the behavior of rectangular reinforced concrete frames subject to a combination of low column loads, beam loads, and lateral load. The analytical tool used in this investigation is a computer program which is a generalized computational method for non linear force deformation relationship and secondary forces due to displacement of the joints during loading.

In the experimental portion of this investigation, two rectangular frames, one design by the Ultimate Strength Design method and the other by a Limit Design method were prepared and tested to failure with short time loading. …

Effective Equation Of State Measurements On Uranium Dioxide, Kenneth Orvis Reil

Nuclear Engineering ETDs

The safety analysis of Liquid Metal Fast Breeder Reactor (LMFBR) systems requires knowledge of the vapor pressure of reactor fuels up to 6000 K. A new technique was developed to obtain experimental vapor pressure data for reactor fuel materials at high temperatures and pressures. Fuel samples are pulse fission heated in the Annular Core Pulse Reactor (ACPR) at heating rates comparable to those anticipated during a severe LMFBR transient. The vapor of reactor fuels may contain several dissociated fuel species, volatile fission products, and/or fission gas. The evo­lution of that pressure may be time or rate dependent. For these reasons, …