Engineering Commons^™

An Experimental Investigation Of Round Normal Impinging Jet Of Water, Dipendra Saharay

Theses

The various flow parameters of round jets of water impinging normally on a flat plate are measured experimentally. The velocity and pressure distribution along the axis of the jet at various sections of the jet parallel to the horizontal lucite striking plate and along the impinging surface was found. The nozzles used were 1/4 inch and 1/2 inch in diameter. The Reynolds number based on the nozzle diameter was 15,000 to 25,000. The distance from the jet origin to the deflecting boundary ranged from thrice the diameter of the jet to twelve and sixteen times the diameter of the jet. …

Kinetics Of Biodegradation Of Phenol And 2,6-Dichlorophenol, Samir Shrikant Desai

Theses

Biological removal of phenol up to 600 ppm and 2,6-dichlorophenol up to 20 ppm was studied in a well aerated fill-and-draw reactor of 41 capacity at 26 C using an activated sludge obtained from the municipal treatment plant in Livingston, N.J. Experimental evaluation of kinetic parameters showed that biodegradation of both phenol and 2,6-DCP followed zero-order kinetics. As expected, the lag time for both compounds was considerably reduced when acclimated sludge was used. However, the metabolism of 2,6-DCP was very slow even for preacclimated sludge, requiring about 36 hours to degrade only 15 ppm.. This was markedly improved by the …

Mathematical Model Of Temperature Profiles And Coking In A Crude Oil Heater Tube, Joseph C. Polimeni

Theses

A mathematical model to predict temperature profiles and coking of crude oil in furnace tubes is presented. The model assumes that the coking mechanism is due to a reaction in the laminar sublayer, whose rate depends upon the temperature profile. That profile is obtained by a numerical solution of the appropriate transport equations, with velocity profiles that may be laminar or turbulent, and including the temperature dependence of the crude oil properties. In addition, velocity and temperature profiles were adjusted when necessary to ensure closure of the heat and material balances. As a by-product of this study, a correction was …

Preparation And Characterization Of Blocked Isocyanate Monomer Polymer And Equilibrium Constant Of Deblocking, Kirti P. Kamdar

Theses

A 2-Hydroxyethyl methacrylate (HEMA) adduct of toluene 2-4 diisocyanate (TDI) was prepared in petroleum ether at 35-40°C under nitrogen. In order to prepare the monomer, equimolar amounts of TDI and HEMA were reacted with P-cresol which functions as a blocking agent.,Di-butyltin dilaurate was used as a catalyst and chloranil was used as an inhibitor. The solid monomer which was obtained was recrystallized, and polymerized in chloroform using azobis isobutyronitrile as initiator.

Monomer and polymer were characterized using infrared spectroscopy, melting point, liquid chromatography gel permeation chromatography. A vapor pressure osmometric study of the polymer in three different solvents at three …

Development Of A Computer-Aided Graphics Capability To Display Field Test Data, L. Allen Adams

Theses and Dissertations

This thesis develops an interactive computer-aided graphics package for the display of experimental and field test data. EXPERT was developed to be used in conjunction with MOVIE.BYU and DISSPLA, utilizing a bivariate interpolation scheme to create a full field of data using the "sparse" field data as pivotal points. The usefulness and practicality of the program is demonstrated by graphically displaying the data from the Air Force Weapons Laboratory's CHEAT test.

Feasibility Of Graywater Systems For The Florida Environment, Joseph L. Tessitore

Retrospective Theses and Dissertations

The objectives of this report was to study the existing literature and data of residential graywater treatment and disposal systems and their possible applications and environmental impacts in Florida. The report addresses mainly (1) the definition of graywater quantity and quality, (2) the evaluation of proposed graywater treatment systems for possible reuse and disposal, (3) the impact of residential graywater systems on existing and proposed wastewater treatment plants, and (4) the possible impacts on groundwater and surface water environment. The report also presents some preliminary residential graywater treatment and disposal system designs including expected treatment efficiencies and cost. It should …

Considerations Involved In Implementing Material Requirements Planning In A Government Contractor Firm, Susan B. Biberman

Retrospective Theses and Dissertations

The government often imposes requirements on their contractors for the purpose of monitoring and control. Many government contractors utilize a matrix organization structure to help cope with the government's ever changing and challenging requirements. It is both the government requirements and this matrix organization which lead to the need for special information and features in a government contractor's manufacturing/material control system. This report specifically addresses those features which would be desirable in a government contractor's MRP system. These features involve the operation of the master schedule, the bill of material, the MRP software, the inventory files, purchasing, and shop floor …

Analysis Of Scheduling For Low Cost Part Task Trainers, William Fellows

Retrospective Theses and Dissertations

This study develops a methodology for the analysis of Part Task Trainer (PTT) refresh scheduling used in conjunction with large simulators. A human performance model is defined through the development of descriptive equations and system random variables. PTT scheduling calculations are performed by employing a computer program simulation. The computer algorithm generates a set of random vectors to represent the learning characteristics of a sample group of individual trainees. The relationships between simulator scheduling time, PTT frequency training, and model variables are demonstrated to be user interactive. This will allow the PTT refresh scheduling program to be used as an …

A Mini Apple Network For Apple Ii Plus Computers, Michael E. Harnage

Retrospective Theses and Dissertations

Computer networks have become increasingly popular over the last ten years. A simple low cost Mini Apple Network that uses Apple II plus computers and Apple's Parallel Interface Cards, is presented here. The Mini Apple Network is driven by PIC DRIVER, a software program that is able to transmit an Applesoft array variable from one computer to another. Three application programs are presented. A comparison is made of the gain in execution time when one, two, and three computers are used to solve the same problem, namely Laplace's partial differential equation. An increase in gain was obtained when the number …

The Use Of Companding In Conferencing Voice Communications Systems, Jon P. Klages

Retrospective Theses and Dissertations

Compounded codes are used for representing voice data in digital communication systems. This thesis addresses the use of the Mu-law companding algorithm in a system optimized for conferencing. A procedure for determining the degree of compression for a variable number of conferees and design equations for implementing a table-lookup scheme using read-only-memories are presented.

The Use Of Computer Vision To Close The Control Loop Of A Robot Arm, Randall S. Janka

Retrospective Theses and Dissertations

Flexible automation is a partial solution to America's industrial and economic recovery and survivability. At the core of this manufacturing technology is the robot whose own flexibility is enhanced through the use of computer vision to close the control loop on the arm and also give the robot environmental intelligence. The basic subdivisions of a computer vision system are sensing, segmentation, description, recognition, and interpretation. When the vision processor analyzes a scene it can give the robot controller symbolic object information and object coordinates. The robot controller transforms such coordinates into its own reference frame through the use of homogeneous …

Three-Phase Unidirectional Surface Acoustic Wave Transducer Model And Computer Aided Design Implementation, Samuel M. Richie

Retrospective Theses and Dissertations

This thesis presents an introduction into surface acoustics wave (SAW) unidirectional transducer (UDT) technologies and identifies advantages and disadvantages of various approaches. A complete model of the three-phase unidirectional structure is presented for the purpose of design analysis. This model incorporates the effects of the electrodes and transducer pattern along with the equivalent circuit model of the transducer structure. The model, when included with the appropriate peripheral components for transducer phasing and matching, can be used to determine accurately the frequency response of a given transducer structure. Such a model is well suited for implementation on a digital computer. With …

The Design Of A Deep Ocean Hydrophone, Michael F. Hackathorn

Retrospective Theses and Dissertations

A design for a deep ocean hydrophone is proposed here. The hydrophone's sound sensing element is comprised of a capped end, piezoelectric cylinder. This sound sensing element is encased in an acoustic coupling fluid filled elastomeric boot. A small diameter tube communicates hydrostatic pressure from the coupling fluid to the interior of the sound sensing element for hydrostatic pressure compensation. The theoretical free field voltage sensitivity, the ratio of open circuit voltage to incident acoustic pressure, is predicted from mathematical model of the sound sensing element.

Interactive Computer Aided Design And Animation Of Spatial Mechanisms, Emmet B. Peter

Retrospective Theses and Dissertations

The synthesis of planar and spatial mechanisms is often accomplished by either trial and error supplemented by computer analysis or by specific analytical techniques in the literature. In either case it is extremely helpful to be able to visualize a physical design as it emerges, and to see a graphic display of it in animated motion. This paper describes the development of a general interactive program for both analyzing and viewing a spatial 4-bar (RSSR) mechanism in animated motion. The analysis provides complete position, velocity, and acceleration information and, for the special case of the planar 4-bar, the same information …

Analysis And Stability Of Closed Surge Tanks, John Emory Fowler

Civil & Environmental Engineering Theses & Dissertations

The equations representing the water surface oscillations in a closed surge tank form a set of nonlinear ordinary differential equations when the system is considered as lumped. Because of the nonlinear terms present in the equations, a closed-form solution of the equations is not available. Several numerical methods ranging from single step methods to higher-order multi-step methods were used to find numerical solutions to the governing equations. As all the methods required a similar amount of CPU time, the degree of accuracy required would determine which numerical method should be used. The effect of various system parameters on the stability …

Treatment Process Optimization At The Lee Hall Water Treatment Plant Newport News, Virginia, Marcy Granum Garnett

Civil & Environmental Engineering Theses & Dissertations

Various methods can be used in operating a water treatment plant. It is desirable to produce good quality water as efficiently and economically as possible. This study evaluates each phase of operation at the Newport News (Lee Hall} water treatment plant for overall efficiency.

This study begins by giving a detailed description of the Lee Hall water treatment plant. The description includes sources of water, a description of each treatment process, a plan view of the treatment plant, and a flow diagram of the treatment plant.

Based on the raw water data, flow rates, and the treatment plant characteristics, the …

The Use Of Complex Versus Normal Modes In Structural Model Improvement, Chih Lin

Mechanical & Aerospace Engineering Theses & Dissertations

In the past, normal modes approximation to complex modes was employed by most researchers or users in the process of identification or modification of structural systems. This is true, of course for simple structures with no or proportional damping. For complex structures with nonproportional damping, even level of which is small, it will be shown that applying this approximation is inadequate. Use of complex modes instead of approximated normal modes is justified.

An algorithm is presented that computes a set of normal modes from the corresponding measured complex modes. The computed normal modes are then used in the Berman's technique …

Pressure Drop Across A Tube Support Plate Of Trefoil Geometry Used In Steam Generator, Raad H. Bashar

Retrospective Theses and Dissertations

This research is concerned with the presentation of pressure drop experimental results across a restriction of trefoil geometry (tube support plate) used in steam generators. The pressure drops were obtained for single-phase and two-phase of air, water, and their mixtures. The tests were performed at atmospheric conditions (pressure and temperature). The loss coefficients associated with these pressure drops were experimentally determined, and empirical correlations for the results were developed. The results were compared with previous studies done on other geometries with air-water mixtures, and also to a similar geometry with steam-water mixture.

Experiments Conducted On The Electron Beam Produced By A Dense Plasma Focus, Mark Steven Pronko

Electrical & Computer Engineering Theses & Dissertations

An experimental investigation was conducted using a 34-kJ Dense Plasma Focus (DPF) in which the possible enhancement of the electron beam was addressed. Electron beams ejected from the DPF have been observed to exceed 30 kA with pulse durations of a few nanoseconds. Enhancement was considered to be either an increase in the probability that the peak beam current exceeded some lower limit, or an increase in the mean energy of the beam electrons. The investigation was divided into two parts, each addressing one of the aspects of enhancement.

In the first part of the investigation, an axial magnetic field …

Optimization Of A New Linear Fm Detector Using Digital Signal Processing Techniques, Edward J.A. Kratt

Dissertations

This dissertation describes and synthesizes a new member of the family of FM detectors introduced earlier by Klapper and Kratt. A salient property of these detectors is low delay with excellent sensitivity. The emphasis in the new detector is on the ease of digital implementation. In addition, the new detector is also extremely linear. In congruence with the other Klapper-Kratt detectors, it makes use of zero group delay elements, balance at RF, quasi-synchronous detection and carrier cancellation. The Performance of the detector is mathematically analyzed under the conditions of a modulated input wave, sinewave [sic] interference, and noise. The results …

The Effect Of Ultrasound On The Hydrolysis Of Carbohydrates, Adel A. Khamis

Dissertations

Acid hydrolysis of dextran and cellulose were studied with and without irradiation with ultrasonic waves of different frequencies (17 - 150 KHz), and powers (0.4 - 200 w/cm²). In the case of both materials, the hydrolysis reaction was found to be first order with respect to the activity of hydrogen ions in the reaction medium. Weight average molecular weight was evaluated at different durations of the reaction course. The reaction rate of dextran was found to be proportional to the weight average molecular weight raised to the power 4/3, and raised to the power 4 for cellulose.

The …

Application Of Fuzzy Theory To Pattern Recognition, David Usechak

Dissertations

Piecewise curve approximation is used to describe boundaries of objects in pictures and waveforms. The method consists of linear and quadratic piecewise polynomial approximations in which the error must not exceed a predetermined cost threshold. A fuzzy Bayes model is used to determine if a breakpoint exists within an interval I_n or between intervals I_n and I_n+1 and to determine whether these intervals can be merged for data compaction reasons. In order to achieve these objectives a new fast algorithm has been proposed which gives good curve/object fitting. This algorithm uses a technique for generating generalized inverse …

Computer Simulation Of The Human Hypophysial-Ovarian System, Robert Charles Blencowe

Theses

In order to more adequately simulate the human pituitary-ovarian cycle further refinements were made to the original Bogumil and Feng computer models. This involved the inclusion of equations which mathematically describe the peripheral conversion of prehormones and a subroutine showing the effect of plasma proteins, TeBG, CBG, and albumin on the total concentration of estradiol, progesterone, testosterone, androstenedione, dehydroepiandrosterone and estrone.

Once the models were functioning properly, values for the normal state and for the disease condition, Polycystic Ovary Syndrome (PCO), were obtained. In most cases there exists good agreement between the results reported in the literature and those generated …

Designing Cost Effective Pump Suction Systems Using Statistical Correlation Techniques To Estimate Vessel Elevation Costs, Neil J. Bernstein

Theses

In order to minimize total costs (investment plus operating costs) when elevating process equipment to meet hydraulic requirements, it is essential to establish cost effective and energy efficient pump suction systems. During the early stages of design of such systems it is most critical that preliminary costs be determined in a timely manner to avoid job delays. One method of accomplishing this is through the use of a cost estimating relationship for defining the price behavior of alternative pump suction systems. This thesis describes the procedure used to develop a mathematical model to predict the cost of elevating vertical drums. …

Industrial Parameters For Applying New Technology, Michael Cimino

Theses

Industrial Parameters for Applying New Technology is a paper devoted to the study of the role 'of' robots in today's manufacturing environment. Industry looks forward to robotic technology to solve, its declining productivity dilemma. The purpose of this paper is to' aid a Prospective robot buyer in selecting the appropriate application and in particular a suitable robot for that application. A listing of robot performance characteristics, criteria chart, and evaluation table were developed to guide the engineer through the necessary steps required in selecting a successful robot application.

The history of robotics is discussed briefly along with an explanation of …

A Study Of Personal Conflict And Stress Among Engineering Personnel As Influenced By Corporate Policy, Stated And Unstated, Richard Brian Gordon

Theses

The following concepts are being challenged: That organizations are efficient, well-managed, and intelligent: that if one is to believe in any sort of authority, one must first accept the notion that it truly knows best and that it is not only competent, but well-intentioned; that organizations exist for the benefit of their employees and customers; that organizations reward dedication, competence, and performance: that if the organization is to grow it needs loyal sacrificing people; that organizations are dynamic and receptive to change; that if the employee is discouraged, do not worry, for tomorrow will be better; that to be useful …

Designing A Data Management System To Support A Quality Control Mission, Erastus Runji Muchioki

Theses

This thesis is concerned with the design of a Data Management System to support a Quality Control Mission particularly within the writer's organization. It defines the term quality, with respect to his company's needs, followed by an outline of quality control management's responsibilities. Problems of quality Control from product design, assembly to the finished product are discussed. The organization's current quality control procedures are analyzed. Problems in establishing the data base are discussed. This data is then organized to form the new Data Management System that will support a Quality Control Mission properly. In the discussion, the author tries to …

Managing In The Technical Sales Arena, Robert Munro

Theses

The major objective of this thesis is to portray the role of a Field Engineer for a major manufacturer of electrical distribution and control equipment. In so doing, it should represent a reasonable facsimile of what a sales manager of a large Field Office, comprised of approximately twelve Field Engineers, would encounter in his supervisory capacity. As such, it should provide information for those interested in entering and hoping to manage in technical sales career.

While much of the information was derived from books, periodicals, and conversations with people associated with the electrical industry, the major portion of the work …

Gallium Nitride Film Deposition By Ionized Cluster Beam Epitaxy, Ghulum Bakiri

Theses

An experimental Ionized Cluster Beam System similar in design to the one developed at Kyoto University in Japan was. designed and constructed in the Microelectronics Laboratory at NJIT. This involved making the working drawings, having the parts machined and then assembling the system in a vacuum system together with the necessary variable power supplies, meters, controls, gas inlets, cooling water connections, etc.

Eleven deposition runs were then attempted to grow gallium nitride utilizing the system constructed. In a typical deposition run, gallium was vaporized from a boron nitride crucible at 1000° C and allowed to expand through a 0.5 mm …

One-Dimensional Compressible Flow Analysis : Isentropic And Normal Shock, Su-Bo Wong

Theses

A computer program to compute and analyse one-dimensional isentropic compressible flow through variable cross-sectional area with or without a normal shock is developed. The program is written in the "FORTRAN LANGUAGE".

In this work, the area change is the predominant cause of change of flow condition. One of the advantage of this program is set on general uses for isentropic flow. In common practice, the values of the isentropic flow property ratios were tabulated or graphically presented as function of the Mach number with a specified specific heat ratio, K (normally K=1.40 was presented). With todays technology, the most versatile …