Engineering Commons^™

Evaluation Of Pressure Capacity Of Rectangular Hvac Duct Plates, Ming-Tui Liu

Theses

The purpose of this thesis is to evaluate the pressure capacity of the duct plates for HVAC design as recommended by Sheet MeLal and Air Conditioning Contractors' National Association, Inc, 1980, whose code is based on the theories of both one-dimensional and two-dimensional analysis. Various sizes of duct width and stiffener spacing for rectangular plates are investigated, Charts and plots are Provided to facilitate the HVAC desidn. A BASIC language program and disc for personal computer is also provided.

A Pitch Based Processor For The Analysis Of Steady State Laryngeal Modes, Tzyy-Jenq Lou

Theses

A data acquisition and analysis stem for use in the study of laryngeal dynamics has been built and tested. The special feature of the system is the computer controlled digitizing rate and coordinated subject pitch prompting. Tokens of steady state laryngeal vibration are obtained from an electroglottograph when the subject intones a series of computer prompted pitchs in a musically scalar sequence. The digital samples of this data are captured by the system at a basic rate of 200 samples per laryngeal cycle. This procedure enables the system to perform a modal analysis of laryngeal function, not unlike the analysis …

Pressure Distributions In Microvascular Network, David Moshenberg

Theses

The objective of this study was to find a practical way of estimating the pressure distribution in a network of microvascular vessels. The pressure distribution was evaluated twice, namely before vasodilations or vasoconstrictions and after the network of vessels reached a new steady state with respect to pressure and flow. Along with determining the pressure distribtuion, the simulation also calculated an effective blood viscosity coefficient for the network.

Poiseuille's equation and the axial component of the equation of motion were used to evaluate the steady state pressure and velocity distributions in each vessel. The continuity equation (conservation of mass) was …

Reliability Problems And Failure Mechanisms Of Solid Tantalum Capacitors, Ghanshyam B. Nakrani

Theses

Today, reliability is acknowledged as an important item in design and the operation of the electronic systems.

This thesis provides some theory, and experiments are instituted to evaluate the reliability for SOLID TANTALUM CAPACITORS made by different manufacturers. The experimental life test work was done at high temperature of 9S 2°C and high humidity of 95 ± 3% on transfer molded tantalum capacitors.

Literature study concentrates on the reliability in solid tantalum capacitors developed between 1961 and 1984.

Several failure mechanisms with figures are illustrated to point out how higher reliability of solid tantalum capacitors may be developed.

The bibliography …

Review Of Construction Management Procedures Of New Jersey Department Of Transportation With The Objective Of Minimizing Claims, Suresh Kumar Ceyyur

Theses

Recent years have evidenced a growing spate of construction claims being filed against NJDOT. A mail survey was conducted and problem areas of NJDOT construction management procedures frequently contributing to claims have been identified. NJDOT's pre-construction scheduling system has been reviewed to suggest improvements and practical integration to obtain effective feedback. NJDOT's organizational structure has many administrative bottlenecks and is overly bureaucratic. An analysis reveals that by way of minimal revamping and by integrating design and construction divisions better coordination can be achieved, bureaucratic norms reduced and the structure made resilient to react quickly to claim situations. Sources and causes …

Microcomputer Controlled Continuous Activity Monitor For Small Caged Animals, Yogesh Parekh

Theses

The task of this instrumentation system is to measure the activity of rats in a controlled experiment. The system is designed to work in conjunction with the system for studies of metabolic rates in rats. The interface circuits take the picture from a video (vidicon) camera into the computer. Once the picture frame is taken into the high resolution graphics screen memory area, the computer uses this data to detect the activity. The movements of the rat are detected by comparing the number of pixels changed between two consecutive picture frames. The area covered by the rat determines the standing …

Computer Simulation Of Drop Weight Impact Tests On Plastic Parts Or Sheeting, Upendra V. Patel

Theses

The ASTM D3029 drop weight test on plasic parts or sheeting is simulated in this thesis. The simulation is accomplished by using the Bruceton staircase method or the Up-and-Down method and the normal distribution theory. The "Probit" method is also analyzed.

The simulation programs are done in FORTRAN computer language. First, the random number generator is used to find the probability value between 0 and 1.0. Then, the cumulative probability distribution formula is used to find the absolute standard normal value. This absolute standard normal value is converted in to X normal value using given input values of mean and …

Axisymmetric Air Jet Impinging On A Hemispherical Convex Plate, Salahuddin Qureshi

Theses

This experimental study was carried out on an axisymmetric air jet impinging normally on a smooth, hemispherical convex plate. Three different nozzles of diameters 0.5in.(12.7mm), 0.375in.(9.525mm) and 0.25in.(6.35mm) were used and the nozzle exit Reynolds number varied from 14,000 to 80000.

The impingement hemispherical plate was made of brass and had a nominal outer diameter of 7.48in (189.99mm).

Calibrated Pitot tubes, U-tube manometer and a micromanometer were used for pressure and velocity measurements. The Pitot tubes were mounted on Precision position mechanisms permitting the accurate traversing in any direction in space. The test air flow rate was measured with calibrated …

Magnitude And Frequency Of Floods : A Comparison Of Regional Methods In The United States, Frank A. Rogalla

Theses

To allow the safe and economical design of structures in flood plains of natural streams, techniques to estimate the magnitude and frequency of floods are established through multiple regression analysis for each state, relating flood peaks to topographic and climatic characteristics of the drainage basins. This study describes and compares the regional equations to assess peak flows for 2, 5, 10, 25, 50 and 100-year recurrence intervals in different states of the U.S.A.

Publications from 40 continental states were reviewed and the regression equations analyzed on similarities and accuracy. Tables compare parameters, their frequency of occurence, and the constants and …

The Impact Of Microcomputers On Engineering And Technical Management Functions, Salvatore Savino

Theses

The purpose of this study was to investigate the perceptions of managers as to the effect of computers on management functions.

Manager perceptions were determined by using a ratio scale of value ranging between 0 and 100. Findings are based on questionnaire responses of 121 top, middle, and lower managers in 120 firms in the United States.

Several hypotheses were examined in the study relative to (1) perceived computer impact on management levels, (2) perceived computer impact on the traditional functions of management, (3) perceived computer impact on levels and functions of management (interaction).

Support was provided for hypothesis of …

Development Of New Products Involving Various Uncertainties For Success, Manuel J. Senra

Theses

The development of new products is a very important task for any company, since the survival of most of the companies depends on their ability to introduce new products on the market. This is not, by all means, an easy task; it is seen from the large number of unsuccessful new products reported.

It is been proved that out of every ten products which emerge from Research and Development(R & D), only two become successes. For reasons like the one mentioned and because larger and larger funds are allocated to R & D, it is a very important task to …

Development Of Robotic Arm Models Using The Integrated Mechanisms Program, Mohan J. Somnay

Theses

The purpose of this thesis is to study the broad concepts and applications of robots in industry and to evaluate the Integrated Mechanisms Program (IMP) for the development of models to suit the requirements of an industrial robot.

IMP is a programmed system for the computer-aided-design and analysis of mechanisms. The use of IMP to analyse and design mechanisms is done through a related problem oriented language which allows a variety of joints to be used.

This thesis describes a general procedure for designing robotic arms. Two mechanisms are modelled using IMP; the first is a jointed arm robot executing …

Application Of The Self-Assessment Technique To Improve The Productivity Of The Project Engineering Function : A Case Study, Roman Stetkiewych

Theses

While traditional industrial engineering methods can be successfully applied to improve productivity in the operations area, their effectiveness is limited where knowledge type work is being performed. For these types of activities, self-assessment has been proposed as a methodology to achieve increased efficiency. This thesis presents the results of applying this concept to the engineering function of a manufacturing firm.

Using a directed set of questionnaires as a focus, a self-assessment of itself was conducted by the Project Engineering Department to consider how well it thought itself to be performing and what its deficiencies were. Co-jointly the departments whose work …

16-Channel Signal Analyzer For Electroencephalograms, Junnyih Chiang

Theses

An instrument has been designed to analyze 16 channels of EEG of a squirrel monkey by using several interface boards controlled by an Apple II computer. This instrumentation system is capable of performing these experiments in an automated manner. It stores the data generated on to a floppy disk, with software control and results may be printed out together with related graphs. Because of the limitation of the floppy disk capacity, we had only developed two versions:

(1) To average the EEG signal up to 8 times for all 16 channels, because a lot of memory is needed to save …

The Catabolism Of Arginine By Lactobacillus Brevis In A Chemostat, Jeanette Carque

Theses

A total of thirty chemostat runs were evaluated for steady state biomass concentration of L. brevis and arginine deiminase activity at dilution rates ranging from 0.022 to 0.1.07 h^-1 for a substrate feed consisting of 1.0% glucose and 0.5% arginine (w/v). Biomass concentration and enzyme activity responses were also evaluated for variations in glucose concentration from 0.05% to 1.5% and variations in arginine concentrations from 0.25% to 1.0% at a constant dilution rate (0.06 h^-1).

The system exhibited multiple steady states for the range of dilution rates from 0.022 to 0.107 h^-1. A steady state …

Transport Phenomena Of Copper Ions Through An Electromembrane, Ren-Fu Cheng

Theses

A separation process based on a new class of membrane ( the electromembrane ) was studied. Experiments were performed using three types of electromembrane to remove copper ions from aqueous solution. A Separation Cell Unit was designed and set up to investigate the transport of copper ions through the electromembranes under the influence of both an electric field and a concentration gradient. Fluxes achieved were much greater than those reported for other membrane processes, and the energy consumption was one half that of electrolytic deposition.

Computer Simulation Of A Batch Distillation Column With A Reflux Divider, Michael Gerard Clarke

Theses

The operation of a batch distillation column with a reflux divider has been mathematically simulated to reproduce operational equipment.

The operation of the column consists of one or more product recoveries. During each product recovery period the column alternates between total reflux and total product withdrawal, with the product withdrawal period being 2 — 5 seconds. Between product recoveries the column operating conditions can be reset.

The basic assumption of this batch distillation simulation is that the column completely equilibrates during the period of total reflux. The determination of the total reflux condition is obtained computationally using the iterative Newton—Raphson …

Scheduling Effects Of 5-(3,3-Dimethyl-1-Triazeno)Imidazole-4-Carboxamide (Dtic) And 1,3-Bis-Chloroethyl-1-Nitrosourea (Bcnu) On Mouse Melanoma Cells B16cl5, Gracie V. Coffey

Theses

DTIC and BCNU have been demonstrated to have enhanced chemotherapeutic effects in mice bearing Bl6 mouse melanoma cells. The order of administration seems to be important in maintaining optimum effects. This was shown is a study by Hill et al. (unpublished).

In the present study, mouse melanoma cells, Bl6CL4, were treated with either DTIC or BCNU. The drug was allowed to remain on the cells for 2, 3, or 4 days. The drug-containing media were then removed, the cells were washed and fresh medium was added. The cells were incubated in an atmosphere of 5% CO2 and 95% air at …

The Biodegradation Of Phenolics Using Mixed Liquor From Passaic Valley Sewerage Commissioners Plant, Newark, New Jersey, Daewon Pak

Theses

The biological degradation of phenol, O-chlorophenol, and 2,6-dichlorophenol was studied at room temperature in aerated 5 liter batch reactors using mixed liquor from Passaic Valley Sewerage Commissioners Plant (Newark, New Jersey). From the concentration versus time data, kinetic rate constants were determined for phenol (at 100 ppm), 2'-chlorophenol (at 20 ppm), and 2,6-dichlorophenol (at 10 ppm). Air stripping and adsorption were determined to be insignificant removal mechanisms for the three compounds studied.

It was noted that the biodegradation rates increased after the organisms were acclimated to 100 ppm phenol. In addition, on substrate exposure, the degradation rate increased from the …

Preparation And Properties Of Novel Dental Adhesives Based Upon Pentaerythritol, Yuan-Yuan Su

Theses

Urethane methacrylates were synthesized from Pentaerythritol, TDI, HEMA and four phenolic blocking agents or from hydroxypropyl methacrylatel TDI and two phenolic blocking agents. All the products were characterized by melting pointy infrared spectroscopy, NMR spectra, and elemental analysis. The bonding of these materials to dentin slices was also investigated. Such materials are supposed to not only react with the organic constituent of dentin but also polymerized with restorative resin. It was found that bond strength was enhanced by the use of the urethane methacrylates, resulting in best mean bonding strengths of 2400 psi.

Digitally Implemented Klapper-Kratt Fm Detector Using The Intel-292o Digital Signal Processor, Chang-Hwan Park

Theses

This thesis describes and analyses a digitally implemented FM detector, which is a new member of the family of FM detectors introduced by Drs. Klapper and Kratt.

The properties of the new detector are low delay, excellent sensitivity, extreme linearity, and compatibility of components with integrated circuit technology.

A working model is implemented by adapting FIR digital s signal processing methods, and is realized using the Single-Chip Digital Signal Processor Intel-2920 which is comprised of micro-processor, scratch-pad data RAMs, program store EPROMs, A/D and D/A conversion circuitry, and I/O circuitry.

The performance of the working model shows very good linearity …

Two Dimensional Diffusional Model For Leakage Of Macromolecules In The Interstitial Space, Suthiluk Dumrongsiri

Theses

Two dimensional diffusion of macromolecules through the interstitial in the hamster cheek pouch was studied with intravital fluorescence microscopy. After topical application of Bradykinin, the movement of Fluorescein isothiocyanate (FITC)-labeled dextrans of average molecular weight 150,000 daltons (Dextran 150) was recorded on videotape which latter was played back frame-by-frame for analysis by digital image processing. Leakage of macromolecules in response to topical application of Bradykinin occurs at discrete leakage site in post caplillary venules of 15-25 um diameter, rather than in the capillary themselves. A mathematical model of two dimensional convection plus diffusion was used to simulate the macromolecule transport. …

Behavior Of High Strength Irregular Shaped Reinforced Concrete Columns Under Combined Biaxial Bending And Compression, Gabriel Hannoush

Theses

Other than rectangular and circular shapes, channel and L-shaped reinforced concrete columns are a common design problem for engineers. Since the available design aids and the current code provisions do not provide adequate guidelines for evaluating the ductility and strength of biaxially-loaded reinforced concrete columns, an experimental and analytical investigation and study of the behavior of biaxially-loaded channel and L-shaped short columns was undertaken.

Four one-quarter scale specimens, two specimens for L-shaped and channel shaped columns respectively, were casted, cured and tested till failure.

Moment, curvature and load deflection curves developed from the experiment were compared with the results obtained …

Automated Arrhythmia Detection In The Exercise Electrocardiogram, Gregory Ciurpita

Theses

A self-adapting, non-real time method for detecting arrhythmias in single channel Exercise ECG is described. Linear and non-linear digital filtering techniques are used to remove additive noise. A time-varying threshold technique is used to detect R-waves based on amplitude. Feature extraction and matched filter methods are used to classify QRS-waves into existing types, or to create new types. The program works on digitized data from floppy disk and plots all data along with classification results on ReGis graphics terminal or printer. This work will continue so that the system will be capable of processing three-channel ECG in real-time.

Analysis And Application Of Automatic Guided Vehicle Systems, Mansuk Bae

Theses

It is the intent of this thesis to analysis the practical applications of Automatic Guided Vehicle Systems (AGVS) as a vital aid in the development of material handling operations within a variety of business sectors.

An evaluation of basis concepts, structural components, practical applications and benefits, and future accessments of AGVS, in terms of material handling are fully discussed. Additionally, a computerized simulation model that calculates "How many Automatic Guided Vehicles Are Needed?" under specific factory conditions and external environmental factors, is both tested and result evaluated.

The author concludes that the use of AGVS as a method for material …

Skyline Technique For Least Square Temporal Finite Element Method, Ying-Woei Hu

Theses

Skyline technique is known to be one of the most efficient numerical methods for solving symmetric and positive definite simultaneous linear algebraic equations whose coefficient matrix is banded and sparse. This technique considers non-zero elements below the skyline only and manipulates Gaussian elimination process efficiently.

In recent years, the finite element methods applied to discretize the space domain has been successfully extended to time domain discretization. This new technique, temporal finite elements, makes it possible to numerically solve initial value problems in a manner similar to boundary value problems.

This thesis introduces skyline technique to one of the temporal finite …

Effect Of Federal Income Tax Regulations On Small Business Decision Making, Leon V. Stanisz

Theses

A comparison of small business organizations was performed in order to see how each is directly or indirectly effected by Federal income tax regulations. Each small business form was examined thoroughly in order to objectively assess organizational advantages and disadvantages and how they are effected by different tax requirements and regulations.

Business expenditures were analyzed to see how and where they could be utilized to the fullest. The thesis tried to examine as thoroughly as possible the cost and the value of these "fringe benefits" both to the company and to the individuals.

The results conclude that any type of …

Computerized Instrumentation System For Indirect Measurement Of Metabolic Changes In Rats, Holger Tebbje

Theses

This work describes the further development of a system for the measurement of the energy expenditure of rats. Based on the concept of indirect calorimetry the respiratory exchange is monitored in a controlled experiment. Rats are held in cages through which air is drawn and analyzed. Transducers and sensors, interfaced to the computer, are measuring the composition and the physical parameters of the gas entering and leaving the chambers. The data recieved is processed, displayed on a screen, printed and stored for later analysis.

The accuracy and repeatability of the system improved by measuring additional parameters like barometric pressure and …

Free Convection Boundary Layer Heat Transfer Analysis Of Isothermal Horizontal Square Plates, Konstantinos E. Tsouras

Theses

The theoretical study presented here examines free convective boundary layer flow and heat transfer over isothermal horizontal square plates.

The boundary layer equations subjected to the appropriate boundary conditions were solved by using Von Karman's approximate integral technique. The analysis was performed by considering an axisymmetric boundary layer because the analyzed phenomenon is three-dimensional in nature. Three-dimensional boundary layer analysis, however, is complicated and the work involved is rather tedious. Consequently, the axisymmetric boundary layer offers a useful alternative. Unfortunately, it was found that this type of analysis is applicable to the case of an upward-facing heated plate only; for …

The Quantitative Analysis Of Airborne Particulates By X-Ray Flourescence, George C. Asteriou

Theses

Airborne particulate matter from the New Jersey State area collected on Quartz Microfiber filters was analyzed by X-Ray Fluorescence spectroscopy. The quantitative analysis of the samples against N. B. S. standards produced results which were compared with Atomic Absorption analysis

The results from the two methods were correlated by the introduction of empirical factors for each element.

However, a larger number of analyzed standards of varied composition, along with the creation of a spectral library, can minimize the need for empirical factors and yield accu¬rate results.