Engineering Commons^™

Numerical Investigation Of Flow Through Wide Angle Diffusers, Moududur Rahman

Dissertations

This study is aimed at the development of a computational technique for the prediction of the flow field in wide angle diffusers. The finite element technique is used for the solution of the governing equations. A commercial software package, NISA/3DFlUID, modified for this specific application was used. The parameters affecting the flow field have been identified. For a wide range of variation of these parameters, the effects on the flow field have been examined. This investigation is an exhaustive and comprehensive numerical study of diffuser flows. Such a study will result in substantial improvement in the understanding of the anatomy …

Aqueous Absorption Of Nitrogen Oxides Induced By Oxychlorine Compounds : A Process Development Study For Flue Gas Treatment, Chen-Lu Yang

Dissertations

The use of chlorine (Cl₂), sodium hypochlorite (NaClO), and sodium chlorite (NaClO₂) as oxidizing agents to promote the absorption of nitric oxide (NO) from gas streams has been investigated in the Gas Scrubbing Laboratory of New Jersey Institute of Technology since 1988. The first step of this project had been to screen out the best scrubbing medium for nitric oxide removal from flue gases. The most successful oxidizing agent was found to be sodium chlorite in acidic aqueous solution. The screening results have been accepted for publication in Chemical Engineering Communications. A sodium chlorite containing aqueous …

An Investigation Of The Formation Of Turbulent Water And Abrasive Water Jets, Md. Ekramul Hasan Khan

Dissertations

This study is concerned with the development of a knowledge base for the selection of nozzle geometry by investigating the mechanism of formation and behaviors of water and abrasive water jets. A numerical prediction of turbulent water flow inside various nozzles is developed. The analysis is based on the numerical solution of conservation equations of continuity and momentum as well as equations of turbulent kinetic energy and dissipation for 2-dimensional axisymmetric flow by using a finite element package, FIDAP.

The technique for determining velocities and forces of water jet and abrasive water jet with the Laser Transit Anemometer and Piezoelectric …

Human Visual System Modelling : Analysis Of Evoked Potential Dynamics, Zongqi Hu

Dissertations

The visual evoked potential (VEP) reflects the electrical activity in the cerebral cortex due to visual stimulation. It contains information on signal processing in the visual pathways from the retina, through the lateral geniculate nucleus (LGN) to the cortical level. Although the VEP is generated by various sources in the multi-layer neural network, the functions of some neuronal mechanisms and the transfer characteristics of particular pathways can be revealed and analyzed by use of carefully designed stimuli (Zemon & Ratliff, 1984; Zemon, Victor & Ratliff, 1986). This dissertation focuses on studies of the visual evoked potential as a composite of …

Computer Aided Stress Analysis Of The Femur With Prosthetic Hip Stem Utilizing Computed Tomography, Wei-Chun Chang

Dissertations

A computer aided design and analysis method, utilizing computed tomography (CT) is developed, which together with a finite element program determines the stress and deformation patterns in the femur with hip prosthesis. The CT scan data file provides the geometry and the material parameters for the generated finite element model. The three-dimensional finite element model of the femur with hip prosthesis is automatically generated from the CT data file by a preprocessing procedure. The preprocessor includes a CT image display, edge detector, nodes generation, prosthesis simulator, mesh generator and model display. The loading conditions applied on the finite element model …

Design And Implementation Of Fuzzy Logic Controller For A Process Control Application, Sujit S. Nerurkar

Theses

Many industrial applications of fuzzy logic control have been reported. This thesis studies and reports the problems associated with the Heat-exchanger temperature control via conventional PID control implemented with Programmable Logic Controllers (PLC) and provides an example of design and implementation of fuzzy logic controllers (FLC's) for a Heat exchanger in a Water for Injection (WFI) system.

After a basic FLC was designed and tested, it is shown how its rule base evolved to achieve superior performance by utilizing additional low-cost sensing information in the process and its environment. A method for the implementation of FLC's into the existing PLC …

An Integrated Mrp And Finite Scheduling System To Derive Detailed Daily Schedules For A Manufacturing Shop, Sita D. Nathan

Theses

Many companies rely on Material Requirements Planning (MRP) to support their Production Scheduling and Control (PS&C) functions. Since MRP does not provide a detailed shop floor schedule, these users have to implement either a third party procedure or an internally developed procedure for shop floor controls. In this thesis we consider a class of user shops which are characterized by the following features:

• Homogenous machines, that is all machines can produce all products.

• Each product requires a setup, but several products may have a common setup.

• MRP requirements are specified on a weekly basis while actual requirements are specified on …

  ---

  Go to article

Time Frequency Analysis Of The Electromyogram During Fatigue, Michelle Rene Davies

Theses

Spectral parameters obtained from the surface EMG signal have been used as indicators of fatigue during a sustained contraction. These same parameters have not been tested with the EMG signals obtained from fine wire electrodes. One such parameter is the median frequency which is known to decline with fatigue. A comparison was done between the median frequencies obtained from the surface EMG and those obtained from the fine wire EMG. The median frequencies from both types of electrodes decreased with time indicating that fine wire electrodes could be used to measure fatigue.

In addition, a new technique, time frequency analysis, …

Application Of The Wavelet Transform To Biomedical Signals, Karl O. Hauck

Theses

The basic concepts and fundamentals of the wavelet signal representation were examined. The orthonormal wavelet was selected for this project after being compared to various types of wavelets. The orthonormal wavelet was chosen due to the equal time and frequency resolution exhibited in the wavelet coefficients. Programs were written in Matlab to implement the orthonormal wavelet in developing wavelet coefficients for a given signal. The programs include the conditions for an orthonormal wavelet in and which produce the wavelet filters g(n) and h(n). The wavelet filters were then incorporated into another program that applied Mallat's multiresolution algorithm for a given …

Transient Behavior Of An Adaptive Synchronous Cdma Receiver, Bin Zhu

Theses

A steepest descent algorithm is used to update the adaptive weights of a two-stage synchronous Code-Division Multiple-Access (CDMA) receiver that was proposed recently. An issue of the adaptive CDMA system - the convergence and stability property of the receiver is investigated in this thesis.

This adaptive synchronous CDMA receiver uses a decorrelator at the first stage and adopts a neural network which acts as an interference canceler at the second stage. It can achieve near-optimum performance. Furthermore, its computational complexity is just a square function of the number of users. The only requirement is the knowledge of the users' signature …

An Adaptive Fusion Model For Distributed Detection Systems With Unequiprobable Sources, Yuzheng Zhang

Theses

In a traditional communication system, a single sensor such as a radar or a sonar is used to detect targets. Since the reliability of a single sensor is limited, distributed detection systems in which several sensors are employed simultaneously have received increasing attention in recent years. We consider a distributed detection system which consists of a number of independent local detectors and a fusion center. Chair and Varshney have derived an optimal decision rule for fusing decisions based on. the Baysian criterion. To implement such a rule, the probability of detection P_D and the probability of false alarm …

Fast Point Pattern Matching By Heuristic And Stochastic Optimization Techniques, Ashish Agrawal

Theses

This work is concerned with one of the methodologies used in the final stages of machine vision: the matching of model point patterns to observed point patterns. Conventional search methods not only fail to arrive at the optimal match, but are also computationally expensive and time consuming. To arrive at the optimal pattern match, stochastic and heuristic optimization as the search technique, exploiting Simulated Annealing (SA), Evolutionary Programming (EP) and Mean Field Annealing (MFA), are explored in detail. A comparison of results obtained using SA versus "hill-climbing" and "exhaustive search" techniques, and results of EP are presented. The relative effectiveness …

Fluid Flow Modeling For Pneumatically Fractured Formations, Deepak Nautiyal

Theses

This thesis investigates the flow of compressible fluids in pneumatically fractured formations. Pneumatic fracturing is a recently developed technique for increasing permeability in geologic formations by the controlled injection of high pressure air. The artificially induced fractures enhance the flow rate of liquids and vapors in the subsurface, and can be applied to in situ remediation of hazardous waste sites, and for other hydrogeological applications.

A flow model for discrete fractures is derived based on the assumptions of viscous, laminar fluid flow through planar fractures (Poiseuille type flow). The model takes into account non-linearity introduced by gas compressibility effects. Provision …

An On-Line Approach For Evaluating Trigonometric Functions, Rajesh Amin

Theses

This thesis investigates the evaluation of trigonometric functions based on an on-line arithmetic approach. On-line algorithms have been developed to evaluate the sine and cosine functions. Error analysis and heuristics are carried out to arrive at a minimal error algorithm based on the series expansion of the sine and cosine function.

A logical design based on the algorithm is presented where the unit is designed as a set of basic modules. A detailed bit slice design of each module is also presented. A simulator was designed as an experimental tool for synthesis of the on-line algorithms, and a tool for …

Design, Construction, And Operation Of Water Treatment Plant Residual Monofills, Haitao Bian

Theses

Due to the stringent environmental regulations, landfilling becomes the most viable option for ultimate disposal of water treatment plant (WTP) residues. At present, most states apply the regulations for municipal solid waste (MSW) landfills to the landfilling of WTP residues. This is too stringent since the WTP residues are not hazardous. Therefore, development of suitable criteria for WTP residual monofills is necessary and urgent.

A set of environmental and geotechnical experiments was conducted to characterize WTP residues. It can be concluded that very little leachate will be produced and migration of leachate is unlikely. Also it was noted that insignificant …

Base Plate Placement For A Predefined Workspace Of A Stewart Platform Parallel Manipulator, Rajesh Chanda

Theses

This thesis deals with solving the problem of placing the base plate in an optimum position and orientation in a three dimensional space for the desired locations of the mobile end platform of a Stewart platform parallel manipulator.

First the workspace of the mobile plate is expressed as a function of the base plate position. Then the objective function is generated by summing the squared distances from the various desired locations of the mobile plate to the center of the platform's workspace. This function consists of six unknown variables which define the position and orientation of the base plate. A …

Coordination Of Time-Overcurrent Relays For High-Speed Power Line Protection, Nicos Charalambous

Theses

A properly coordinated protection system is essential to ensure that an electricity distribution network can operate within its requirements, regarding the safety of a power system. Automatic operation is necessary to isolate faults on a power system in a minimum time. The study of time coordination of relays suggests improved ways of power line protection. The protection must be sensitive enough to operate when a fault occurs under minimum fault conditions, yet be stable enough not to operate when its associated equipment is carrying the maximum rated current, which may be a short-time value. A power system is used as …

Modeling Arsenic Transformation In Clay Soils, Chao-Yi Chung

Theses

This project is designed to estimate the possible transformation forms of arsenic in clay soil. A computer model was established to simulate arsenic transformations. The amount of arsenic species adsorbed, dissolved, and the predominant soluble species are calculated by the model, which is mainly based on the Freundlich adsorption isotherm, solubility data collected by Keaton and Kardos, and pH-Eh diagram established by Ferguson and Garvis. The computer language used is Turbo PASCAL version 5.5.

The clay soil environment is considered to be in standard state: 25°C 1 atm. Environmental factors of the soil system which are accounted for by the …

In Vitro Testing And Evaluation Of Intraaortic And Extraaortic Balloon Counterpulsation Devices, Joseph V. Izzo

Theses

The primary purpose of this project was to develop an in vitro environment in which the intraaortic and extra-aortic balloon pumps could be tested and evaluated. This was done by modifying a mechanical heart simulator -- the pulse duplicator system -- to accommodate both devices, and developing a software system that could collect and process the data relevant to the operation of the two balloons.

Both counterpulsation techniques were tested in the pulse duplicator where the aortic pressure and flow data were collected. The software system then processes the data to calculate all of the parameters affected by counterpulsation.

While …

Fabrication And Characterization Of Wsi2/P-Si And Tasi2/P-Si Devices, Anitha Kodali

Theses

Thin films Silicides of Tungsten and Tantalum have become very important for IC manufacturing. W and TaSi₂ films were deposited on silicon substrates by CVD and Co-sputtering techniques respectively. These films have been characterized using current-voltage technique. The analysis of the obtained experimental measurements has been performed in the light of Schottky-Mott theory. The effects of annealing were studied using Rapid Thermal Processing technique in the temperature range of 500 to 700°C, in nitrogen atmosphere at a constant pressure of 5x10^-6 ton for a duration of 30 seconds.The increase in annealing temperature resulted in the formation of ohmic …

The Use Of Cod As An Indicator For Evaluation Of Pretreatment Of Nitrocellulose With Acid Hydrolysis, Han-Chung Lee

Theses

Nitrocellulose is a toxic waste by definition. It is widely used in military and commercial industries. Nitrocellulose fines escaped from the manufacture's process has created problems in receiving water. However, little information is available for the treatment of nitrocellulose. Nitrocellulose is difficult to treat by microorganisms without any pretreatment. Therefore, the main objective of this study is to use acid hydrolysis to break down this material before biological treatment, and find the optimal operation conditions in this process.

In this work, the results indicate that percentage of nitrocellulose decomposing in hydrolysis depends on types of acid, acid concentration, reaction temperature, …

A Graphical Tool For Timed Petri Nets Using Object Oriented Programming, Baopu Liu

Theses

The objective of this effort is to develop a computer tool for drawing, editing and simulating Timed Petri Nets using object oriented programming. The developed C++ based Timed Petri Net Simulation Tool, TimedPNT, is capable of simulating discrete systems with both deterministic and stochastic delays. Preselection is used for conflict resolution. Performance and utilization results are automatically collected. XView™ Toolkit is used for building the TimedPNT's interactive graphical interface in compliance with AT&T's OPENLOOK® standard on a SunSparc™ IPX running SunOSTM 4.1.2. Compliance with the X Window standard makes the developed tool portable to other X Window based systems.

Machining Of Silicon Wafers With An Abrasive Water Jet Cutter, Frank J. Marciniak

Theses

This thesis consists of a study of the effects of abrasive water jet cutting on brittle silicon substrates. In total, 26 different cuts were made in a single crystal silicon substrate with an abrasive water jet cutter under different conditions of water flow, water pressure, and abrasive flow rate. These cuts were analyzed for surface roughness, and microstructure.

The roughness measurements were compared in order to determine the best possible cutting conditions. The cut with the best roughness of 0.000170 inches was obtained under cutting conditions of 30 KSI water pressure, 1 inch/minute cutting speed, and an abrasive flow rate …

Concurrent Engineering And Design For Manufacture In The Medical Device Industry, Martin A. Mathelier

Theses

Concurrent Engineering (CE) is an approach to product development in which engineers work on design and manufacturability at the same time. The ultimate goal of concurrent engineering is to reduce the time-to-market while improving quality. This thesis goes into details about the tools necessary to achieve successful product development in the Medical Device Industry. The novelty of this thesis is not in the tools themselves but rather in the way that they are applied to the medical device industry. The need for the CE approach is of utmost importance because of the vast competition in the medical device industry.

The …

Prediction Of Linear And Non-Linear Components Of Cutter Deflection In End Milling Tools, Kimberly Nazimek

Theses

In this study, cutter length, cutter diameter, depth of cut, and magnitude of the instantaneous force vector are examined to determine their effects on cutter deflection during end milling. Their contributions to both linear and non-linear cutter deflection are examined. Models are developed to compute deflection for both flat and ball end mills. These models are evaluated to determine the contribution of each type of deflection encountered during a variety of milling conditions. A discussion on the transfer of deflection data to an estimation of machining accuracy is then presented.

Reconstruction And Enhancement Of Medical Computed Tomography Images, Manoj K. Pattahil

Theses

The aim of Computed Tomography is to obtain information regarding the nature of the materials occupying precise positions inside the body. But due to errors in the projection data, which arise due to errors in measurement, beam hardening, missing data and noise, the reconstructed image has artifacts which reduces its diagnostic value. Thus the image obtained has to be processed to remove these artifacts and to improve the quality of the image. This is achieved by iterative reconstruction along with different post-reconstruction processing. Iterative reconstruction is done by repeating the process of projecting the image and creating new projection data …

A Knowledge-Based Designer Assistant System With Application To The Design Of Helical Springs, Giridhar Raja

Theses

Design problems are generally difficult to solve because the domain of solutions is often infinite (like design of gears, bearings, shafts, springs etc.) and generally requires several iterations before we can arrive at the right solution. The search for the right solution satisfied by several constraints is also time consuming. Thus design intrinsically requires backtracking and several iterations to obtain the desired solution.

In the design of helical springs where the load, deflection, allowable stress, and material are specified, there are an infinite number of solutions. If, in addition to these requirements, the mean coil radius, wire diameter, free height …

Biomechanical Comparison Of Interosseous And Subperiosteal Flexor Tendon Reattachment, Alisa Beth Olin

Theses

This study was undertaken to biomechanically compare the interosseous and subperiosteal distal flexor tendon reattachment techniques. Twenty New Zealand white rabbits underwent division of the right second and third hind limb profundus flexor tendon distal to the insertion of the superficial flexor. All tendons were repaired using the Kleinnert-Bunnell configuration with a 5-0 nylon tied over a cotton pad on the dorsum of the digit. In half of the animals, the second profundus was reattached into a hole in the middle phalanx and the third profundus was reattached after periosteal stripping of the middle phalanx. The other animals underwent subperiosteal …

Development And Evaluation Of A Nfweav Simulation Model For Weaving Areas Under Non-Freeway Condition, Wen-Min Pan

Theses

The development of a microscopic digital computer simulation model representing vehicle interaction at a weaving area under non-freeway condition is presented. Weaving areas are classified into two categories: 1. Weaving caused by merging and diverging of a ramp with an arterial, 2. On/off ramps connecting an arterial with a highway. The principal characteristics of the simulation model are the following: 1) a car following and lane changing model were used to represent vehicle movements; 2) an anti-collision check algorithm was developed for all vehicle movements; 3) driver merging urgency and follower courtesy model were developed for weaving vehicles. The simulation …

Performance Of National Research And Education Network While Transmitting Healthcare Information Data, Bhavesh Mahendra Shukla

Theses

National Research and Education Network(NREN) is a first step in the process of building a National Information Infrastructure(NII). NII will ultimately lead to Broadband Integrated Services Digital Network(B-ISDN), a network which will support global exchange of voice, data, images and video.

NREN will evolve out of present National Science Foundation Network (NSFNET), also known as Interim NREN. At present NSFNET operates at 45 MBits/sec. By 1996, there are plans to boost the data rate to 155 MBits/sec and to 620 MBits/sec by the turn of century.

In this thesis, present actual NSFNET is simulated using software simulation tool Networkll.5. The …