Engineering Commons^™

Hardware Implementation Of The Complex Hopfield Neural Network, Chih Kang Cheng

Theses Digitization Project

No abstract provided.

Convergence Properties Of Perceptrons, Ratnasri Krishna Adharapurapu

Theses Digitization Project

No abstract provided.

Development Of A Desuperheater Rating Method For Energy Code Calculations, Tim Merrigan

Retrospective Theses and Dissertations

The purpose of this project was to develop a rating method for desuperheater water heaters – heat exchangers that remove superheat from the refrigerant in an air conditioner’s compressor discharge line. The project methodology was to first determine the overall heat transfer coefficient-area product (UA) of the heat exchanger for three basic types of desuperheaters. Both heat transfer analysis and the laboratory performance data indicated that the number of transfer units (NTU) for each heat exchanger was relatively independent of the operating conditions for a properly-charged air conditioner with a single-speed compressor and a desuperheater with a single-speed circulating pump. …

Finite Impulse Response Utilizing The Principles Of Superposition, Scott Edward Carter

Retrospective Theses and Dissertations

Window functions have been greatly utilized in the synthesis of finite impulse response (FIR) filters implemented using surface acoustic wave (SAW) devices. The critical parameter in any FIR design in the impulse response length, which must be optimized for the given design specifications in order to reduce the size of each device. To this end, many design algorithms have been introduced such as Remez exchange, linear programming, and least mean squares. A new algorithm has been derived which is efficient and accurate for the design of arbitrary filter specifications requiring less computations than the current algorithms. The FIR design is …

Electrical Power Dispatch To Motors Using Digital Modulating Techniques, David Michael Canny

Theses

The trend towards digital and microprocessor based control of power electronic converters has increased the level of research into digital modulating techniques. This thesis examines the inherent digital nature of Binary Rate Modulation with particular attention concentrated on its suitability for dispatching power to three-phase loads. The circuit topology of a three-level inverter is also examined and its performance aspects are compared with those of the more conventional two-level inverter.

Integral cycle Binary Rate Modulation is applied to an ac voltage controller and this method of power dispatch, which displays an optimal ac cycle positioning property, is compared with Pulse …

Thermoplastic Composites Of Recycled High Density Polyethylene And Recycled Tire Particles, James N. Mckirahan Jr.

Masters Theses

This study identified the mechanical properties and processibility of composite materials of recycled high density polyethylene (HDPE), recycled rubber tire particles, and/or ethyl co-vinyl acetate and poly (e-caprolactone). The composites were processed using a single screw extrusion system.

Three groups of experiments were conducted, on the composites in their extruded form to investigate the mechanical properties of ultimate tensile strength, percent elongation, and hardness. The first experiment investigated the effect of recycled rubber particle concentration in the composites up to 25 percent. The second experiment investigated the effect of recycled rubber particle size on the composites of recycled HDPE and …

Nonlinear Robust Control Of A Series Dc Motor Utilizing The Recursive Design Approach, Michael J. Burridge

Retrospective Theses and Dissertations

In this thesis, the investigation of asymptotic stability of the series DC motor with unknown load-torque and unknown armature inductance is considered. The control technique of recursive, or backstepping, design is employed. Three cases are considered. In the first case, the system is assumed to be perfectly known. In the second case, the load torque is assumed to be unknown and a proportional-integral controller is developed to compensate for this unknown quantity. In the final case, it is assumed that two system parameters, load torque and armature inductance, are not known exactly, but vary from expected nominal values within a …

A Silicon Knife Design And Fabrication, Mingli Wang

Theses

In this thesis, the design and fabrication of a silicon knife is described. The device design is based on the principle of oxidation sharpening.

The knife is made from a silicon wafer and can be made to be any chosen length up to 150 mm. It was made with the same basic procedures used in semiconductor chip manufacturing. This type of processing/manufacturing results in a knife with a high degree of sharpness and smoothness compared with existing knife technology.

The knife fabrication plan combines IC processing, techniques including anisotropic and isotropic etching of silicon, plasma dry etching and chemical etching …

Study Of The Time Efficiency And Volume Of Wood Used For Three Types Of Stove In The Salitrón Community Of San Juan Ermita, Department Of Chiquimula, Fredy Samuel Coronado López

Theses and Dissertations

In developing countries such as Guatemala, firewood is increasingly being used for cooking in most rural areas. Consequently, there is a shortage of firewood in these areas beca use trees do not grow at the same rate as they are consumed. Some authors report that 90% of the heat from firewood is lost during combustion. Several alternatives to open pit fires exist to reduce the amount of firewood used. However, these alternatives need to be evaluated to determine their efficiency. This project compared the time efficiency and volume of firewood used in the Finlandia style improved stoves, Josefina stoves, and …

Calculating Cross Slot Flux Losses In High Voltage Stator Coils, John D. Amos

Retrospective Theses and Dissertations

At present there are several methods for calculating temperature for inner-cooled stator coils for large electric generators. Determining the highest temperature in a stator coil is very important and is a major limiting factor for the maximum capability of steam turbine synchronous generators.

The load current in the stator winding causes losses in the conductor resistance. That same current excites leakage fluxes that link contours inside the conductors causing non-uniform current distribution and additional losses. these additional losses are caused by eddy currents induced inside the stator coils. These eddy losses are grouped as radial flux losses, cross slot flux …

Gaussian Beam Resonator Formalism Using The Yy Method, Kenneth A. Menard

Retrospective Theses and Dissertations

A simple and powerful new paraxial ray formalism is shown to provide an alternate method for designing Gaussian Beam Resonators. The theory utilizes the Delano yybar diagram approach and is an extension of the recent work by Shack and Kessler for laser systems. The method is shown to be complementary to the conventional ABCD method and is founded upon J.A. Arnaud's pioneering ideas for complex rays. The thesis develops an analytic formulation of a ray based complex wavefront curvature and yields a clearly generalized description of spherical wave propagation, for which Gaussian beams are considered a special case. The resultant …

Analysis And Extension Of Model-Based Software Executives, Keith E. Lewis

Theses and Dissertations

This research developed a comprehensive description of the simulation environment of Architect, a domain-oriented application composition system being developed at the Air Force Institute of Technology to explore new software engineering technologies. The description combines information from several previous research efforts and Architect's source code into a single, comprehensive document. A critical evaluation of the simulation environment was also performed, identifying improvements and modifications that enhance Architecture's application execution capabilities by reducing complexity and execution time. The analysis was then taken one step further and presented extensions to the current simulation environment. The extensions included investigating the feasibility of mixed-mode …

The Design Of Fir Filters With Linear Or Non-Linear Phase Using The Kaiser Window Function And A Novel Superposition Method, Cai Zurong

Retrospective Theses and Dissertations

A new design method for FIR filters using the Kaiser window is presented in this paper. Near optimal frequency response and impulse response can be obtained for a given • set of specifications. The synthesis procedure uses the summation of frequency translated and scaled Kaiser functions. The method can be used to design linear phase or non-linear phase filters, and symmetric or non-symmetric arbitrary magnitude response filters. This design method is based on the frequency domain using the approximate Fourier transform of the Kaiser window function. The design procedures and examples for linear and arbitrary phase filters are discussed in …

A Neural Network Thrust Force Controller To Minimize Delamination During Drilling In Graphite Epoxy Laminates, Robert B. Stone

Masters Theses

"Delamination is a well-recognized problem associated with drilling in fiber-reinforced composite materials (FRCM). The most noted problems occur as the drill enters and exits the FRCM. Since drilling is often a final operation during assembly, any defects introduced in parts by drilling represent an expensive loss. Studies based on linear elastic fracture mechanics theory have proposed critical thrust forces in the various drilling regions that will prevent crack growth or delamination. Using these critical thrust force curves as a guide, a thrust force controller was developed to minimize the delamination while drilling in graphite epoxy laminates. A neural network control …

Visage: Improving The Ballistic Vulnerability Modeling And Analysis Process, Brett F. Grimes

Theses and Dissertations

The purpose of this thesis was to improve the process of modeling and analyzing ballistic vulnerability data. This was accomplished by addressing two of the more urgent needs of vulnerability analysts; the ability to display fault tree data and to edit target descriptions. A vulnerability data visualization program called VISAGE was modified to meet these needs. VISAGE was originally created to preview static shotline plots and subsequently grew into a full-featured visualization package for vulnerability target descriptions and analyses data. The next logical step in the programs evolution was to include the needed editing and fault tree display capabilities. The …

Iron Phosphate Glasses As A Potential Nuclear Waste Disposal Medium, Melissa G. Mesko

Masters Theses

”Phosphate glasses containing large amounts of Fe₂O₃ (up to 43wt%) were studied to determine their potential suitability as nuclear waste disposal glasses for high level radioactive wastes containing large concentrations of iron oxide, phosphate, and fluoride compounds. Glass formation and chemical durability was the prime focus of this study, while properties such as density, thermal expansion, dilatometric softening temperature, and devitrification temperature were examined as well. It was found that large amounts of simulated nuclear waste material (up to 44.4wt% Cs₂O or 37.5wt% SrO) could be incorporated into the base iron phosphate glass while retaining …

A General Method For The Inverse Kinematics Of Rotational Displacements In Spatial Mechanisms, John D. Kliminski

Theses

An iterative technique was developed to solve the inverse kinematics problem for the joint rotations in both closed-loop and open-loop spatial mechanisms and robotic manipulators in any prescribed configuration. The method is based on fixing one link in space and maneuvering the other links to form a closed chain, following an approximation of the actual physical assembly of the mechanism. In order to apply the same principle to both types of mechanisms, an open-loop mechanism was modeled as a closed-loop mechanism by creating a fictitious fixed link in the free space between the base and the end of the chain …

An Investigation Into Artificial Intelligence Based Generative Computer Process Planning, William Tereshkovich

Theses

The process planning function can be further optimized with the introduction of an intelligent software package such as an Artificial Intelligence based Generative Computer Process Planning System. An AI based CAPP system, also categorized as an expert system, provides the vital link between design and manufacture, a "bridge" of knowledge in the information chain of manufacturing engineering. With the increasing role of computers in the process planning function, planning has become easier, faster, and more efficient.

This thesis provides an explanation of the process planning function and how artificial intelligence will improve it. Topics in AI techniques and procedures, knowledge …

Hardware For Fast Global Operations On Distributed Memory Multicomputers And Multiprocessors, Douglas V. Hall

Dissertations and Theses

"Grand Challenge" problems such as climate modeling to predict droughts and human genome mapping to predict and possibly cure diseases such as cancer require massive computing power. Three kinds of computer systems currently used in attempts to solve these problems are "Big Iron" multicomputers such as the Intel Paragon, workstation cluster multicomputers, and distributed shared memory multiprocessors such as the Cray T3D. Machines such as these are inefficient in executing some or all of a set of global program operations which are important in many of the "Grand Challenge" programs. These operations include synchronization, reduction, MAX, MIN, one-to-all broadcasting, all-to-all …

Beam Modes Of Lasers With Misaligned Complex Optical Elements, Anthony A. Tovar

Dissertations and Theses

A recurring theme in my research is that mathematical matrix methods may be used in a wide variety of physics and engineering applications. Transfer matrix techniques are conceptually and mathematically simple, and they encourage a systems approach. Once one is familiar with one transfer matrix method, it is straightforward to learn another, even if it is from a completely different branch of science. Thus it is useful to overview these methods, and this has been done here. Of special interest are the applications of these methods to laser optics, and matrix theorems concerning multipass optical systems and periodic optical systems …

Nonlinear Finite Element Micromechanic Analysis Of Thermoplastic Composite Of Recycled High Density Polyethylene Reinforced With Short Glass Fibers, Qiming Lou

Masters Theses

This thesis studied the nonlinear micromechanic behavior of thermoplastic composite of recycled high density polyethylene (HDPE) reinforced with short glass fibers using finite element method. The composite material was modeled using a micromechanic unit cell to simulate the stress distribution between the plastic matrix and the fiber in the composite. Nonlinear behavior of recycled HDPE and imperfect bonding between the fiber and matrix were investigated. Load-bearing capability of the fiber was evaluated using stress partition ratio (SPR) in the composite models. The effect of fiber aspect ratio on the stress distribution of the composite was studied to optimize the material …

Diagnostic And Adaptive Redundant Robotic Planning And Control, Anya Lynn Tascillo

Graduate Dissertations and Theses

Neural networks and fuzzy logic are combined into a hierarchical structure capable of planning, diagnosis, and control for a redundant, nonlinear robotic system in a real world scenario. Throughout this work levels of this overall approach are demonstrated for a redundant robot and hand combination as it is commanded to approach, grasp, and successfully manipulate objects for a wheelchair-bound user in a crowded, unpredictable environment. Four levels of hierarchy are developed and demonstrated, from the lowest level upward: diagnostic individual motor control, optimal redundant joint allocation for trajectory planning, grasp planning with tip and slip control, and high level task …

A Nonlinear Dynamic Method For Supporting Large-Scale Decision-Making In Uncertain Environments, Wayne Woodhams

Engineering Management & Systems Engineering Theses & Dissertations

This research developed a methodology for supporting decision making by reducing uncertainty in decision environments which are too large, dynamic and complex to be treated by traditional quantitative and simulation techniques. These environments are complex because of the free choice associated with human involvement, and the existence of a large number of interrelated factors which influence the outcomes of the decision process. They are dynamic because the ground rules affecting those interrelationships are constantly changing. Uncertainty cannot be treated probabilistically, since identification of a full set of outcomes and factors of influence is not possible.

The venue for the investigation …

Assessment Of Non-Mechanical Thermo-Syphon Solar Pump, Tarek Hassan Selim

Archived Theses and Dissertations

No abstract provided.

Investigation Of The Relationship Between Fuel Injection Nozzle Roto Flow And Hydra Flow And The Engine Torque Of A Diesel Engine, Guang Jin

Dissertations and Theses @ UNI

The purpose of this study was to investigate the possibility of reducing diesel engine torque variation by optimizing fuel injection nozzle tip configuration. In order to reduce engine torque variation, test runs were conducted to determine whether fuel injection nozzles affected diesel engine torque. There was a further effort to determine whether a correlation existed between the fuel injection nozzle roto flow and hydra flow, and the engine torque at specified engine speeds.

Engines installed in cotton pickers and tractors were used for this study. Engines, five from the cotton picker and five from the tractor group were chosen randomly …

Perceived Importance Of Iso 9000 Factors As Indicators Of Quality In Industrial Technology Related Programs At Four-Year State Regional Universities, Floyd L. Olson

Dissertations and Theses @ UNI

Industry has often used a quality standard known as ISO 9000. No evidence has been located demonstrating the applicability of an industrial quality model to a singular academic department. The problem of this study was to determine if the guidelines for ISO 9004-2 could have been considered appropriate for Industrial Technology related programs and how they could have been used to indicate quality within such programs.

The purpose of this study was to seek knowledge relating the importance of ISO 9004-2 guidelines to audit and/or improve the quality management of Industrial Technology related departments at 4-year state regional universities. This …

Effect Of Agricultural Fiber Reinforcement On The Mechanical Properties Of A Recycled Polyethylene Plastic Composite Material, Michael E. Courbat

Dissertations and Theses @ UNI

This study determined the effect of certain agricultural fiber reinforcements on the tensile and impact mechanical properties of a recycled polyethylene plastic composite material. The purpose of the study was to provide information on certain mechanical properties of a recycled polyethylene plastic material as part of a coordinated materials application process.

A prototype product run of the plastic composite material was done and test specimens were selected from this material. Notch impact, tensile, and flexure tests were conducted on test specimens. Test procedures complied with accepted standards from The American Society For Testing and Materials (ASTM). Tests were conducted on …

An Analysis Of The Use Of Programmable Controllers To Control An In Situ Leach Mine Wellfield, Jimmy W. Stokey

Dissertations and Theses @ UNI

In situ mining is a relatively new method that has the potential of recovering a variety of minerals. This process is quickly becoming an alternative to conventional mining techniques that are environmentally unsound. Two problems associated with in situ mining are, the amount of waste water generated by the process (bleed) and the uncontrolled migration of lixiviant outside the production zone (an excursion).

The purpose of this study was to determine if in situ mining processes could be monitored and controlled with a Sequential Control and Data Acquisition (SCADA) system. Using programmable logic controllers, a cost-effective SCADA system was designed …

Comparing Traditional Statistical Models With Neural Network Models: The Case Of The Relation Of Human Performance Factors To The Outcomes Of Military Combat, William Oliver Hedgepeth

Engineering Management & Systems Engineering Theses & Dissertations

Statistics and neural networks are analytical methods used to learn about observed experience. Both the statistician and neural network researcher develop and analyze data sets, draw relevant conclusions, and validate the conclusions. They also share in the challenge of creating accurate predictions of future events with noisy data.

Both analytical methods are investigated. This is accomplished by examining the veridicality of both with real system data. The real system used in this project is a database of 400 years of historical military combat. The relationships among the variables represented in this database are recognized as being hypercomplex and nonlinear.

The …

Cossap Simulation Model Of Ds-Cdma Indoor Microwave Atm Lan, Keng T. Tan

Theses : Honours

This thesis presents an original work in the area of designing and implementing a simulation testbed for modelling a high speed spread spectrum Asynchronous Transfer Mode (ATM) Local Area Network (LAN). The spread spectrum technique used in this LAN model is Direct Sequence Code Division Multiple Access (DS-CDMA). The simulation model includes at least a physical layer of such a LAN, embedded into the COSSAP¹ simulation environment, and has been fully tested. All the newly developed building blocks are comprised of standard blocks from the COSSAP libraries or compatible user-built primitive blocks (only where it is absolutely necessary), and …