Engineering Commons^™

Statistical Modeling And Optimization Of Nuclear Waste Vitrification, Todd E. Combs

Theses and Dissertations

This thesis describes the development of a methodology to minimize the cost of vitrifying nuclear waste. Pacific Northwest Laboratory (PNL) regression models are used as baseline equations for modeling glass properties such as viscosity, electrical conductivity, and two types of durability. Revised PNL regression models are developed that eliminate insignificant variables from the original models. The Revised PNL regression model for electrical conductivity is shown to better predict electrical conductivity than the original PNL regression model. Neural networks are developed for viscosity and the two types of durability, PCT-B and MCC-1 B. The neural network models are shown to outperform …

Automatic Synthesis Of Vlsi Layout For Cmos Continuous-Time Filters, Wei Han

Dissertations and Theses

Automatic synthesis of digital VLSI layout has been available for many years. It has become a necessary part of the design industry as the window of time from conception to production shrinks with ever increasing competition. However, automatic synthesis of analog VLSI layout remains rare.

With digital circuits, there is often room for signal drift. In a digital circuit, a signal can drift within a range before hitting the threshold which triggers a change in logic state. The effect of parasitic capacitances for the most part, hinders the timing margins of the signal, but not its functionality. The logic functionality …

Numerical Simulation Of Contaminated Sediment Transport In The Upper Columbia Slough System, Binghong Wu

Dissertations and Theses

An integrated modeling system has been developed to simulate sediment and contaminated sediment transport in the Upper Columbia Slough System during the Flood of 1996. The modeling system consists of a hydrodynamic model, a sediment transport model, and a contaminant transport model. The hydrodynamic model predicts the Slough flow dynamics and sediment transporting power; the sediment transport model predicts flow-induced sediment transport; and the contaminant transport model predicts the migration of contaminated sediments in the Slough system.

The Upper Columbia Slough modeling system is characterized by its recognition of the complex interplay of Slough hydrology, hydrodynamics, sediment transport, contaminant transport. …

A Telescopic Approach To Modeling Leachate Dynamics And Migration At The St. Johns Landfill, Portland, Oregon, Thomas Stephen Lowry

Dissertations and Theses

The St. Johns Landfill is a 225-acre site that lies near the confluence of the Columbia and Willamette Rivers, in the North Portland Industrial District of Portland, Oregon. A slough system surrounds the landfill on three sides with the fourth side adjacent to a shallow lake. The landfill first opened in 1930 when it was operated as an open dump. It operated as an open dump until 1969 when it was converted to a sanitary landfill, employing daily cover and compaction. The landfill was closed in 1991.

The landfill sits directly on top of a thick layer of silty overbank …

A Simplified Approach To Reduce Blocking And Ringing Artifacts In Transform-Coded Images, Jianping Hu

Dissertations and Theses

Presently Block-based Discrete Cosine Transform (BDCT) image coding techniques are widely used in image and video compression applications such as JPEG and MPEG. At a moderate bit rate, BDCT is usually a quite satisfactory solution to most of practical coding applications. However, for high rate compression it produces noticeable blocking and ringing artifacts in the decompressed image. It has been an active research area for a decade for reducing these artifacts. In this thesis, a novel post-processing algorithm is proposed to remove the blocking and ringing artifacts at low bit rate. It is non-iterative and uses both spatial and transform …

Optimizing Airborne Area Surveillance Asset Placement, Douglas E. Fuller

Theses and Dissertations

Currently there is no automated planning tool for the optimum positioning of USAF area surveillance assets for a theater level campaign. This research seeks to find the optimum or near optimum placement of the limited USAF airborne surveillance assets against a theater level target set. The problem of finding the optimum orbit points can be modeled as a classic maximal covering location problem (MCLP). Operational constraints on the placement of surveillance aircraft can be handled by preprocessing the potential orbit points to eliminate infeasible orbit points. Heavy emphasis is placed on preprocessing the data to reduce problem size and hence …

Experiments In Aggregating Air Ordnance Effectiveness Data For The Tacwar Model, James E. Parker

Theses and Dissertations

An interactive MS Access&trademark; based application that aggregates the output of the SABSEL model for input into the TACWAR model is developed. The application was developed following efforts to create a functional approximation of the SABSEL data using neural networks, statistical networks, and traditional statistical techniques. These approximations were compared to a look-up table methodology on the basis of accuracy, (RMSE

Determining The Economic Plausibility Of Dual Manifesting Reusable Launch Vehicles And Reusable Orbital Transfer Vehicles For The Replenishment Of Military Satellites, Crystal L. Evans

Theses and Dissertations

Currently, the Air Force launches military satellites on expendable launch vehicles to low earth orbit (LEO), and with the use of a chemical upper stage or an apogee kick motor, moves the satellite to a higher orbit. This launch procedure is extremely costly because it requires additional launch preparations, technology considerations, equipment, and fuel. Also, the additional mass of the chemical upper stage causes a larger, and thus more expensive, launch vehicle to be required. An economical alternative is to utilize reusable launch vehicles (RLVs) and reusable orbital launch vehicles (ROTVs). This concept could possibly achieve even greater savings if …

A Cost Impact Assessment Tool For Pfs Logistics Consulting, Angela P. Giddings

Theses and Dissertations

Response surface methodology (RSM) is used for optimality analysis of the cost parameters in mixed integer linear programming. This optimality analysis goes beyond traditional sensitivity and parametric analysis in allowing investigation of the optimal objective function value response over pre-specified ranges on multiple problem parameters. Design of experiments and least squares regression are used to indicate which cost parameters have the greatest impact on the optimal objective function value total cost-and to approximate the optimal total cost surface over the specified ranges on the parameters. The mixed integer linear programming problems of interest are the large-scale problems in supply chain …

Analysis Of Aircraft Sortie Generation With Concurrent Maintenance And General Service Times, Daniel V. Hackman

Theses and Dissertations

The primary objective of this study was to develop an analytical methodology for evaluating an aircraft sortie generation process. The process is modeled as a closed network of general service queues with a fork join node to model concurrent servicing. The model uses the Mean Value Analysis (MVA) algorithm and general queueing network analysis by decomposition to approximate network performance measures including resource utilization and the overall sortie generation rate. The results of the study show that the analytical approximation's accuracy decreases as server utilization increases. However, when server utilization is kept in realistic ranges, the approximation is very accurate. …

Applying Tabu Heuristic To Wind Influenced, Minimum Risk And Maximum Expected Coverage Routes, Mark R. Sisson

Theses and Dissertations

The purpose of this thesis is to provide Air Combat Command a method for determining the number of predator unmanned aerial vehicles (UAVs) required to cover a pre-selected target. Extending previous research that employs reactive TABU search methods for deterministic vehicle routing problems, this thesis incorporates wind effects that can significantly alter the travel times for any given scenario. Additionally, it accounts for possible attrition by introducing minimum risk route and expected number of target covered to the objective function. The results of the TABU search and subsequent Monte-Carlo simulation: gives the number of predator's required to cover a target …

Sensitivity Of Availability Estimates To Input Data Characterization, Darren P. Durkee

Theses and Dissertations

Reliability analysts are often faced with the challenge of characterizing the behavior of system components based on limited data. Any insight into which model input data is most significant and how much data is necessary to achieve desired accuracy requirements will improve the efficiency and cost effectiveness of the data collection and data characterization processes. This thesis assesses potential significant factors in the probabilistic characterization of component failure and repair behavior with respect to the effect on system availability estimates. Potential factors were screened for significance utilizing fractional. factorial and Plackett-Burman experimental designs for several system models developed using an …

Analytical Solutions Of Openings Formed By Intersection Of A Cylindrical Shell And An Oblique Nozzle Under Internal Pressure, Hengming Cai

Dissertations

Since several decades ago, many authors have published their research results about local stress distributions of shells and shell-nozzles both analytically and numerically. However, there has not been a published paper, which deals with analytical solutions of cylindrical shell and oblique nozzle, even though in the case of openings formed by intersection of a cylindrical shell and an oblique nozzle.

A comprehensive analytical study of local stress factors at the area of openings formed by intersection of a cylindrical shell and an oblique nozzle under internal pressure is presented in this dissertation.

By means of traditional approach in theory of …

Adaptive Distributed Detection With Applications To Cellular Cdma, Jian-Guo Chen

Dissertations

Chair and Varshney have derived an optimal rule for fusing decisions based on the Bayesian criterion. To implement the rule, probabilities of detection P_D and false alarm P_F for each detector must be known, which is not readily available in practice. This dissertation presents an adaptive fusion model which estimates the P_D and P_F adaptively by a simple counting process. Since reference signals are not given, the decision of a local detector is arbitrated by the fused decision of all the other local detectors. Adaptive algorithms for both equal probable and unequal probable sources, for independent …

Synthesis And Characterization Of Lpcvd Sic Films Using Novel Precursors, Mahalingam Bhaskaran

Dissertations

A unique low pressure chemical vapor deposition (LPCVD) process has been developed to synthesize amorphous and crystalline SiC films using environmentally benign chemicals. The interrelationships governing the process variables, compositions and select properties of the resulting films were established. Such films can be used to produce high quality mask membrane for x-ray lithography. These films can also be used in fabricating high power electrical devices, and hetrojunction devices in conjunction with silicon.

Amorphous SiC films were synthesized using a single precursor, ditertiarybutylsilane, at temperatures below 850°C. Compositional analysis performed on these deposits revealed that, in the deposition temperature range of …

Bilinear Time-Frequency Representations Of Heart Rate Variability And Respiration During Stress, Rindala Saliba

Dissertations

Recently, joint time-frequency signal representation has received considerable attention as a powerful tool for analyzing a variety of signals and systems. In particular, if the frequency content is time varying as in signals of biological origin which often do not comply with the stationarity assumptions, then this approach is quite attractive. In this dissertation, we explore the possibility of better representation of two particular biological signals, namely heart rate variability (HRV) and respiration. We propose the use of time-frequency analysis as a new and innovative approach to examine the physical and mental exertion attributed to exercise. Two studies are used …

Two Dimensional Agonistic Control, Daqing Yang

Dissertations

The conventional method of precise multiple-axis motion control entails use of a multiple axis positioning system with each axis carrying not only the workpiece but also the positioning system of the remaining axes. The resultant structure is heavy, sluggish, and expensive. An alternative positioning technique is being investigated in which the motion of the workpiece is controlled by pulling it with tendons, each of which has its own actuator. Since the actuators can be mounted on the base of the structure instead of being carried by motion system of the other axes, they can be relatively large and powerful without …

Evaluation Of Environmental Characteristics Of Wtp Residuals For Disposal In Monofills, Ping Tian

Dissertations

Disposal of water treatment plant (WTP) have raised great concerns due to the stringent water quality standards and environmental regulations, and limited availability of land for ultimate disposal. The ultimate disposal of water treatment plant residuals by using monofill may be one of the most economical, and feasible options. Design and operation of such a monofill will be simple because of the uniformity of the characteristics of WTP residuals.

The objectives of this project were to determine the environmental characteristics of WTP residuals and to apply these characteristics for the design of monofills and development of the metal leaching model …

Counterpulsation Cardiac Assist Device Controller Defection Filter Simulation And Canine Experiments, Carl Edward Werner

Dissertations

Electronic control systems for counterpulsation Cardiac Assist Devices (CADs) are an essential part of cardiac assistance. Synchronization of the counterpulsation CAD controller with the cardiac cycle is critical to the efficacy of the CAD. The robustness of counterpulsation CAD controllers varies with the ability of the CAD controller to properly trigger on aortic pressure (Pa) and electrocardiogram (ECG) signals for sinusoid rhythms, non-sinusoid rhythms and non-ideal signals resulting from surgical intervention. An analog-to-digital converter and digital-to-analog converter based CAD controller development platform was devised on a 33Mhz PC-AT.

Counterpulsation Pa systolic rise and dicrotic notch detectors were demonstrated with a …

Non-Linear Evaluation Of Concrete-Filled Steel Tubular Columns, Mohammad Hassan Shams

Dissertations

Concrete-filled steel tubular (CFT) columns have become increasingly popular in structural applications due to their high strength, high ductility, and large energy absorption capacity. These structural properties are the result of integral behavior of the concrete core and the steel tube. This research provides an analysis of the interaction of the concrete core and the steel tube in CFT columns.

While there have been many experimental studies of CFT columns, there has been no analytical work modeling the confining effect of the steel tube on the concrete core. Furthermore, current design procedures tend to underestimate the ultimate strengths of CFTs …

Shaped Charges Having A Porous Tungsten Liner-An Experimental And Theoretical Study Of Metal Compression, Jet Formation And Penetration Mechanics, Brian Edward Fuchs

Dissertations

The use of porous tungsten as a liner for shaped charges to improve their penetration was proposed by Ki-Hwan Oh in his invention disclosure "Shock Extrusion of Ingots from Powders or Solids", at the New Mexico Institute of Mining and Technology, Socorro NM on June 7, 1988. The intention was to increase the ductility of the normally brittle metal by heating the liner to a high temperature by shock compaction during its acceleration just before jet formation.

The feasibility of increasing the ductility of tungsten in this way is the subject of the present study. The theory and prior experimental …

Potential Effects Of Pneumatic Fracturing On Existing Structures And Utilities, Michael C. Canino

Theses

This thesis develops a mathematical design model for predicting ground deformations resulting from pneumatic fracturing. Pneumatic fracturing is a patented process developed for the purpose of enhancing the in situ treatment and removal of hazardous contaminants from geologic formations. During pneumatic injections, measurable ground deformations are experienced both during and after the process. Safe application of pneumatic fracturing to contaminated plumes occurring beneath existing structures and utilities requires that the elastic deformation behavior of the geologic formation and overlying structures be quantified.

Data from five pneumatic fracturing sites were regressed to establish the characteristic polynomial describing the curvature of ground …

Design, Simulation And Fabrication Of A Mems In-Situ Contactless Sensor To Detect Plasma Induced Damage During Reactive Ion Etching, Subramanian Ganesh

Theses

The present trend in the semiconductor industry is towards submicron devices. An inevitable process technique in achieving this is by reactive ion etching of the polysilicon gate. During RIE, the gate oxide may get damaged due to several causes. One of the main causes of the damage is the non-uniformity of the plasma. It is reported that these plasma inconsistencies are mainly due to electrode design and that they create spatial plasma potential fluctuation. These fluctuations are reported to be in the range of 10-20 Volts. By providing an in-situ monitoring of the wafers, the reliability of the device could …

A Methodology For The Design Of An Integrated Air Stripping/Biofiltration Process To Clean Contaminated Aquifers, Pothitos Ioannis Stamatiadis

Theses

This thesis deals with the conceptual design of an integrated air stripping/biofiltration process for cleaning aquifers contaminated with volatile organic pollutants. In this technology, the pollutant is transferred from the aquifer to an air stream which is subsequently treated in a biofilter. The work presented here is an effort to develop a design methodology for the integrated process and suggests a general, quantitative approach which can be used in preliminary technology evaluation. This methodology involves relatively simple equations for the stripping process and detailed (oftentimes complex) models for biofiltration under conditions of continuous variation of the properties of the polluted …

Synthesis And Characterization Of Hafnium Carbide Thin Films, Wiriya Thongruang

Theses

Hafnium carbide thin films of various characteristics were deposited on silicon substrates using dc magnetron sputtering. A HfC target was used as a sputtering source and Ar was used as a sputtering gas during deposition. The variables investigated were total sputtering gas pressure and power. Optimum characteristics were achieved with a total sputtering gas pressure of 5 mTorr and power of 200 W. No evidence for oxidation of the film was found at a depth below 400A for deposited and annealed films. Binding characteristics were obtained from ESCA data. The compressive film stress increased when sputtering gas pressure decreased. The …

Measuring The Need For Manufacturing Flexibility And Evaluating Its Economic Benefits, Navin Karwande

Theses

Flexible systems are known of enabling organizations to take advantage of diversified products, low volume production items with short life-cycles. They also improve the ability to respond to market changes. Flexibility has thus become a strategic manufacturing need in recent years.

Because of the high initial capital outlay involved, the selection of the appropriate flexible solution has become a critical issue. This thesis proposes a methodology to determine the most cost effective and feasible flexibility strategy. A flexibility audit is developed to analyze and evaluate the changes taking place in a facility's environment. These changes and a measurement scheme is …

Performance Evaluation Of Cebus Power Line Communication In The Presence Of X-10 Module Signaling, Nashwa F. Kamel

Theses

A power line of CEBus has great potential towards inexpensive home automation. Both PLBus and X-10 uses [sic] burst of 120KHz signals to transmit bits of information on the power line. However, these two systems are completely incompatible and can conflict with each other. This thesis presents the first performance evaluation of Power Line CEBus communication in the presence of X-10 module signaling. The evaluation included simulation experiments measuring packet delays, message delays, message throughput, channel throughput and the percentage of messages received in error verses [sic] different loads. Network performance has been confirmed to function well in terms of …

Design Of A Mode Of Delivery For Macrobead Transplantation, Jagdip Desai

Theses

The macrobead is a form of a biohybrid artificial pancreas (BAP), which is being developed to treat type 1 diabetes. A hypothetical human transplant would require 125 rat equivalent macrobeads. For intraperitoneal transplantation a mode of delivery that allows the placement of several hundred macrobeads into a basket or pouch type device is required.

In this study, four commercially available materials were studied as possible candidates for creating a pouch. These materials are polyvinyl chloride acrylic copolymer (PVC), polyethersulfone (PES), polyvinylidenedifluoride (PVDF), and polytetrafluorethylene (PTFE). Tubular pouches of each material were designed. They then underwent in vivo biocompatibility and in-vitro …

A Cost Model For Multi-Lifecycle Engineering Design, Bin Zhang

Theses

Design for Environment aims to yield a product whose aggregate environmental impact is as small as possible. This thesis characterizes a product recovery system and defines the concepts of product lifetime and part lifetime. A multi-lifecycle product recovery model is developed based on the concepts of product tree and disassembly path representation, four product recovery choices, time varying costs, cost comparison. The four product recovery choices of a part in the product tree are: Reconditioning, Part Remanufacturing, Material Recycling, and Landfill. This thesis focuses on how to improve the product design while minimizing environmental impact of the product and introduces …

Tcp/Ip Traffic Over Atm Network With Abr Flow And Congestion Control, Liping An

Theses

Most traffics over the existing ATM network are generated by applications running over TCP/IP protocol stack. In the near future, the success of ATM technology will depend largely on how well it supports the huge legacy of existing TCP/IP applications.

In this thesis, we study and compare the performance of TCP/IP traffic running on different rate based ABR flow control algorithms such as EFCI, ERICA and FMMRA by extensive simulations. Infinite source-end traffic behavior is chosen to represent, FTP application running on TCP/IP. Background VBR traffic with different ON-OFF frequency is introduced to produce transient network states as well as …