Engineering Commons^™

The Effect Of Central Screw And Post Vault Containment On Reverse Total Shoulder Arthroplasty (Rsta) Baseplate Stability, Mickaela J. Gunnison

All Theses

Reverse total shoulder arthroplasty (RTSA) is a procedure that aims to fix irreversible rotator cuff damage and degenerative glenohumeral joint diseases that hinder arm abduction. One major complication of RTSA is glenoid baseplate failure resulting from increased movement at the bone-baseplate interface. This study examined 36, 12 PCF composite Sawbones® scapulae. The specimens were split equally into 6 study groups, each having different implant configurations with varying baseplate lateralization and central screws or posts. Each specimen was subjected to cyclic shear loading and failure testing on an Instron to determine implant micromotion and load values.

After testing, ANOVA tests were …

Phasor-Domain Short-Circuit Analysis Of Power Transmission Systems In The Presence Of Inverter-Based Resources, Dol Kunwar

All Theses

Although a power system is nonlinear during healthy operation because of constant power loads and controlled power injections from the sources, a conventional power system fed by synchronous generators is linear during fault, and can be represented by bus impedance matrix (Z-bus), which is useful in power system analyses such as short circuit (SC) analysis. However, With increasing penetration of inverter-based resources (IBRs) in the system, the assumption of linearity of the faulted network does not hold. This impacts the analyses relying on Z-bus and Thevenin’s equivalent impedance (TEI), such as certain protection schemes set using short circuit analysis. Therefore, …

Light-Induced Phase Separation Purification For Monoclonal Antibodies, Xuyang Chen

All Theses

none

Multi-Domain Secure Dds Networks For Aerial And Ground Vehicle Communications, Daniel Pendleton

All Theses

none

Innovative Rate Design As A Free Market Solution To Climate, Resiliency, And Economic Challenges, Brendan J. Moore

LSU New Orleans Theses and Dissertations

A century-old problem of electricity rate design is cost-shifting between ratepayers (Wellinghoff, J. & Tong, J., 2015). A much newer cost-shifting example of great and increasing importance happens whenever ratepayer generated “renewable energy” is sold to the grid—all too often, this is accused of being unfairly rewarded (Ritchie, 2016). ProRate resolves both these concerns and ProRate can actually be derived simply from the premise of avoiding “all” cost shifts between ratepayers (Katz, CLEPm Rewards to Arrest Demand Cost-Shifting, 2019; Katz, CLEP5 Rewards to Arrest Energy Cost-Shifting, 2019). Another major problem with the Old Utility Model is the lack of price …

Towing Tank Trials Of Hydrokinetic Turbine Scale Model To Support Marine Energy System Verification, Shahab Rouhi

LSU New Orleans Theses and Dissertations

In response to the escalating demand for sustainable energy solutions and the critical reevaluation of conventional fossil fuels due to environmental concerns, this dissertation embarks on a comprehensive exploration of hydrokinetic energy as a promising alternative. The study delves into the underexplored domain of hydrokinetic energy, leveraging innovative methodologies for effective utilization and harnessing, particularly through the development and investigation of hydrokinetic turbines.

In the realm of hydrokinetic energy conversion, our research has exclusively concentrated on horizontal-axis turbines, distinct from other turbine configurations. Noteworthy is the adaptation of a conventional horizontal-axis wind turbine for water currents, revealing enhanced performance through …

Summonable Construction Delivery Robot, Kevin M. Lewis

Honors Capstones

In many different construction industries, there is a need for tools, parts, and other necessary items to be transported quickly and efficiently over various types of terrain. Human resources have often been used to address these needs, which can become very time and cost inefficient over long periods. The design proposal here is aimed at addressing this need by developing an autonomous outdoor mobile robot based on a quadrupedal robot design. This approach differs by incorporating a wheeled and quadrupedal hybrid actuation system that provides terrain negotiation and speed at the appropriate times. The team uses Robot Operating System (ROS) …

Great South Metals: Slitter Head Building Process, Nabhan Karim, Evan Swierski, Raven Morin, Patrick Kelsey, Michael Williams

Senior Design Project For Engineers

Great South Metals (GSM) operates two steel slitter machines, which take large coils of flat rolled steel and cut them into smaller strips for use in customers’ applications. Setting up the working components of each machine, called the slitter head, is a precise and arduous task. This system relies on several manually performed calculations and acute attention to detail; and thus, is prone to human error. The management at GSM commissioned our team to simplify the slitter head assembly process by creating an automated computer program and make additional recommendations to improve their operations.

The program we created is a …

Diegetic Sonification For Low Vision Gamers, Jhané Dawes

Master's Theses

There are not many games designed for all players that provide accommodations for low vision users. This means that low vision users may not get to engage with the gaming community in the same way as their sighted peers. In this thesis, I explore how diegetic sonification can be used as a tool to support these low vision gamers in the typical gaming environment. I asked low vision players to engage with a prototype game level with two diegetic sonification techniques applied, without the use of their corrective lenses. I found that participants had more enjoyment and experienced less difficulty …

Analyzing Diverse Student Experiences: The Intersection Of Equity, Inclusivity, And Biomedical Engineering Education Through A Clinical Observations And Needs Finding Course, Jacquelynn Horsey

Biomedical Engineering Undergraduate Honors Theses

In the field of biomedical engineering, needs identification and solution development are an important element of the design process. In our undergraduate curriculum, a course was designed to allow clinical observation and provide an opportunity for students to learn about engineering design and engage with clinicians via completing rotations in medical facilities near our campus. While this type of course is not unique, evaluating its efficacy is not simple. Given the broad range of institutional resources available- such as proximity to a medical school, or residency programs- reporting the quality of such courses within the context of such available resources …

The Determination Of Macrophage Localization In Muscle Injuries Using Spatial Transcriptomics, Julliana Renales

Biomedical Engineering Undergraduate Honors Theses

The repair of traumatic muscle injury is often a long process which can in many cases be insufficient and incomplete. In such cases, scar tissue may form, leading to high risk of re-injury and the prevention of muscle regeneration. An important part of decreasing this risk is gaining a better understanding of the cellular complexities of injury repair. More specifically, macrophage cells are an important piece in the regulation of inflammation and repair. In this project, computational analysis spatial transcriptomic data was performed to examine mouse muscle injury and its development over time. This analysis was used to examine the …

Investigation Of Early Stage Wound Healing In Volumetric Muscle Loss, Sean Ong

Biomedical Engineering Undergraduate Honors Theses

Volumetric muscle loss (VML) refers to the substantial removal of tissue from skeletal muscle due to surgery or lesions. This condition disrupts the normal regenerative process of injured muscles, leading to significant loss of muscle function. This study examines the progression of VML injury, approximately 20% of the muscle mass being removed, in the tibialis anterior (TA) muscle of a mouse model over a 15-day post-injury period. The injured muscles exhibited discoloration indicative of reduced blood flow and experienced a decrease in muscle mass throughout the study duration. Furthermore, the maximum force output of the injured TA was significantly lower, …

Multifunctional Surfaces By Ultrafast Laser Multiscale Surface Structuring, Kewei Li

All Dissertations

Surface structures are crucial for regulating surface functions, including self-cleaning, surface coloration, and anti-fouling, which are of significance in various applications such as prolonging the lifetime of the solar cells, anti-counterfeiting marking, and enhancing the vessel’s performance. Ultrafast laser technology emerges as a revolutionary approach for surface structuring, distinguished by its exceptional precision, high throughput, versatility across materials, and remarkable processing efficiency. Despite the intensive study in the ultrafast laser surface structuring area, the fundamental mechanisms accounting for the ultrafast laser-induced surface structures are still not well understood. The correlation among laser processing parameters, surface structures, and surface functions remains …

High Bandwidth Hybrid Current Sensor Readout Interface For Power Applications, Asma Mahar

Graduate Theses and Dissertations

High-density and power-efficient circuits have become realizable with the advent of wide bandgap semiconductor devices due to their high switching speed and lower conduction/switching losses. The operation of these circuits requires current information for protection, monitoring, and control. For the realization and a further boost in the efficiency of such power circuits, small size, non-invasive, high bandwidth current sensors with noise immunity, accuracy, and linearity are required. Various hybrid sensors have been reported to meet the requirements of emerging power circuits. A combination of a magneto resistor or Hall sensor and a coil is used to cover a wide frequency …

Text-To-Speech Animation: Generating Visuals Based On Phonetic Spelling, Colin Tomcak

Theses/Capstones/Creative Projects

Speech is a complex field, and remarkably difficult to master. There exist many groups who could use more tools to help improve their pronunciation of English words. The goal of this project was to create a text-to-speech animation program as an addition to our group capstone, Pronunciation Pal. Pronunciation Pal is a web-based application meant to assist those who are deaf or hard of hearing in improving their pronunciation, likely as an addition to therapy with a speech pathologist. This application uses tools like diagrams and references to help users better understand how to pronounce a word. The goal of …

Characterization And Analysis Of Supersonic Flow Through De Laval Nozzles At Varied Design Conditions, Sarah Baird

Doctoral Dissertations and Master's Theses

A combined numerical and experimental investigation of supersonic planar nozzles under different design conditions has been conducted. Supersonic planar nozzles are common geometries observed in supersonic wind tunnels and aircraft or rocket engines. For the important role they play in wind tunnel testing and aircraft propulsion, it is important to conduct a thorough numerical and experimental study to characterize their performance at different operating conditions. In this study, a de Laval nozzle was scanned to extract its contours and subsequently modeled to compare analytical and numerical performance expectations under design and off-design conditions. The nozzle was then installed in a …

Investigation On The Effects Of Biofouling On The Boundary Layer, Adam N. Bacon

LSU New Orleans Theses and Dissertations

This study is an investigation of the effect of biofouling on the boundary layer of a flat plate and a NACA 4-digit series foil. Three identical hydrofoils made of resin were placed in the Gulf of Mexico at Grand Isle, Louisiana, and observed and analyzed by marine biologists at the University of New Orleans for their species composition. The resulting biofouling that grew was primarily made up of barnacles and bryozoans. The foils were submerged in an open channel flume at zero incidence and subjected to a series of experiments whose arc-length Reynolds numbers ranged from approximately 13000 to 32000. …

Developing Relationships Between Macroporosity And Tensile Strength By Imaging Failure Planes, James C. Mazzagotte Iii

Boise State University Theses and Dissertations

Porosity, which measures the empty spaces within rock structures, is crucial for determining properties like density, hydraulic conductivity, and mechanical strength, covering both microporosity and macroporosity. While many studies have explored how porosity affects compressive strength and stiffness in different rock types, less attention has been paid to its influence on tensile strength, especially in extrusive igneous formations like vesicular basalt. This research aims to fill this gap by investigating the relationship between macroporosity and tensile strength in vesicular basalt.

The study employed non-destructive techniques, including machine learning and manual image analysis, to calculate porosity, dividing it into specimen porosity …

Data Analysis Of Twitter’S Nasdaq100 Sentiments And Topics As Indicators For News Articles Retrieval: Fine-Tuning Roberta And Rag, Kagan Timur

ICT

This study explores the combination of sentiment analysis with vader-lexicon and semantic analysis with latent dirichlet allocation to identify real-life events, particularly in the context of Twitter datasets. While sentiment analysis alone may not provide accurate guidance, the inclusion of semantic analysis enhances the research process by helping to identify relevant news articles and comprehend brand perception on social media. Furthermore, the study fine-tunes the RoBERTa model specifically for question-answering tasks

The Analysis Of Mechanical Exfoliation Of Graphene For Various Fabrication And Automation Techniques, Lance Yarbrough

Mechanical Engineering Undergraduate Honors Theses

Mechanical Exfoliation of Graphene is an often-overlooked portion of the fabrication of quantum devices, and to create more devices quickly, optimizing this process to generate better flakes is critical. In addition, it would be valuable to simulate test pulls quickly, to gain insight on flake quality of various materials and exfoliation conditions. Physical pulls of graphene at various temperatures, pull forces, and pull repetitions were analyzed and compared to the results of ANSYS simulations, solved for similar results. Using ANSYS’ ability to predict trends in exfoliations, flake thickness and coverage using stress and deflection analyses were investigated. Generally, both strongly …

Large Eddy Simulation Of Fluid Mixing In Migadome Facility For The Astfe Nuclear Thermal Hydraulics Cfd Competition, Kolten Strauss

Mechanical Engineering Undergraduate Honors Theses

This paper is a documentation of a submission to the First Annual ASTFE Nuclear Thermal Hydraulics Computational Fluid Dynamics (CFD) Competition [1]. To validate simulations of turbulent mixing in buoyancy-driven flows, an air and argon test case was set up inside the University of Michigan’s MiGaDome mixing vessel. This submission to the competition used a polyhedral mesh of about two and a half hundred thousand cells, a Large Eddy Simulation (LES) of the MiGaDome, and the Wall-Adapting Local Eddy-viscosity (WALE) subgrid approximation model. The competition included a factor considering the energy cost of our simulations, so it was decided to …

Experimental And Numerical Investigation Of Air-Cooled Heat Sinks, Ethan Weems

Mechanical Engineering Undergraduate Honors Theses

Lightweight and affordable cooling capabilities are critical as the physical scale of electronics continues to decrease. Air-cooled heat sinks that dissipate heat from electronic components to the surrounding air are excellent candidates to fill this role. While plate-fin and pin-fin heat sinks have been implemented extensively for electronic cooling, recent advances in additive manufacturing enable the fabrication of more complex structures. In this undergraduate Honors thesis, a means by which to generate novel heat sink geometries is presented. To that end, an experimental characterization facility is developed to evaluate existing traditional heat sinks. The heat transfer performance of the heat …

A Review And Analysis Of General Aviation Instructional Accidents, Sydney Sommers

Mechanical Engineering Undergraduate Honors Theses

General aviation student pilot accidents represent a substantial portion of all aviation accidents in the United States. Almost 50% of general aviation accidents involve student pilots. Analyzing historical accident reports is the most common approach to studying accident causation. The National Transportation Safety Board (NTSB) investigates all civil aviation accidents in the US. Using the NTSB data, I analyzed general aviation student pilot accidents in the US between 2013 and 2022. Results indicate that most accidents take place in California and Florida and can be attributed to student pilots between 18 and 65 years of age. Alaska and Maine had …

Comparative Analysis Of Command Protocols For Cubesat Data Handling Systems, Roman Dowling

Mechanical Engineering Undergraduate Honors Theses

Researchers at the University of Arkansas developed ARKSAT-1, a cubic satellite with the purpose of employing an LED with a tracking system to perform spectroscopic measurements of the atmosphere.

The control board of the satellite contained several microcontrollers which worked in concert to collect and manage data. Discussed in this report are the software programs developed for the microcontrollers, dual Arduino MKRZeros, utilized as data repositories and for control of satellite peripherals. The programs discussed in this project include an original existing command-response protocol and an improved batch-command protocol, each with its accompanying data handling and storage system. These programs …

A Study Of Varying Dielectric Constant And Thickness Of Dielectric Barrier Discharge Devices And Their Subsequent Plasma Actuation, Sharon Kardasz

Mechanical Engineering Undergraduate Honors Theses

The principles of air-breathing ion propulsion are relatively unestablished in the aerodynamic realm as traditional forms of combustion for propulsion systems have remained in use. However, due to increasing environmental, economic, and efficiency concerns of traditional combustion, interests in innovative propulsion methodologies, such as electric propulsion, are emerging. A primary technology of interest for use of ion propulsion is the Dielectric Barrier Discharge Device (DBD). Preliminary research conducted at the University of Arkansas has determined the most favorable DBD geometry. This work will continue the preliminary research to decipher the most favorable DBD configuration by varying dielectric thickness and dielectric …

Cosmic Object Space Management Operations System (C.O.S.M.O.S.), Riah Ivy, Tyler Bumpus, Gabriel Soter

Senior Design Project For Engineers

In the expansive realm of outer space, humanity has ventured into new territories, yet this progress is accompanied by challenges. Among the most significant challenges confronting space exploration today is the growing amount of space debris within low earth orbit. Satellites, spent rocket stages, and assorted fragments orbiting Earth present a considerable hazard to spacecraft and astronauts, and this issue is steadily worsening. For years, the task of remedying this orbital congestion has remained formidable and unresolved. This design provides a novel and innovative solution to this growing problem.

Gamification Of Speech Therapy With Pronunciation Pal, Parker Zbylut

Theses/Capstones/Creative Projects

This capstone report examines the theory and implementation behind applying game design principles to educational applications, and explores their implementation in an educational game through the Pronunciation Pal application. The gamification of learning tools aims to increase learners' engagement and attentiveness with a subject by restructuring content using game design principles of challenges, rewards and feedback. Feedback can be delivered via visuals and/or sounds, as well as regular indicators of player progress and accomplishment. In addition, a successful game implementation establishes challenges to facilitate a player's intrinsic desire to continue playing and improving at the skills presented by the game. …

Brain-Inspired Continual Learning: Rethinking The Role Of Features In The Stability-Plasticity Dilemma, Hikmat Khan

Theses and Dissertations

Continual learning (CL) enables deep learning models to learn new tasks sequentially while preserving performance on previously learned tasks, akin to the human's ability to accumulate knowledge over time. However, existing approaches to CL face the challenge of catastrophic forgetting, which occurs when a model's performance on previously learned tasks declines after learning the new task. In this dissertation, we focus on the crucial role of input data features in determining the robustness of CL models to mitigate catastrophic forgetting. We propose a framework to create CL-robustified versions of standard datasets using a pre-trained Oracle CL model. Our experiments show …

Cal Poly Fluid Power Vehicle Challenge 2024, J. Mason Gray, Ryan D'Amour, Alberto Acho Lopez, Christian Ferrandino, Johnathan Dietz

Mechanical Engineering

In this Final Design Review, the Cal Poly Fluid Power Vehicle Team competed in Norgren’s 2024 Fluid Power Vehicle Challenge. The design need of the competition was for college teams to compete with human-powered, hydraulic-driven vehicles in an endurance race, a sprint race, an efficiency race, and a regenerative power race. The competition need was to design a vehicle to win in as many races as possible, achieving the highest overall score and winning the competition. With a design emphasis on the endurance and sprint race, the Cal Poly team designed a fluid power system that fastened to a purchased …

Examining The Relationship Between Manning's Roughness Coefficient And Stage, Henry Holtkamp

Biological and Agricultural Engineering Undergraduate Honors Theses

This paper uses LOESS regression to predict Manning's roughness coefficient to calculate flows in natural stream channels. Manning's roughness coefficient can introduce variability into Manning's equation, potentially destabilizing results. Utilizing LOESS to find n based on backcalculated n from collected discharge vs. stage information is the best way to acquire accurate Manning's roughness coefficient values at a variety of flows. Book values tend to drastically overestimate which can have wide-ranging implications for water allocation, flood management, maintaining environmental flows, and maintaining water quality.