Engineering Commons^™

Characterization Of Interlayer Laser Shock Peening During Fused Filament Fabrication Of Polylactic Acid (Pla), Fabien Denise

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The field of additive manufacturing (AM) has gained a significant amount of popularity due to the increasing need for more sustainable manufacturing techniques and the adaptive development of complex product geometries. The problem is that AM parts routinely exhibit flaws or weaknesses that affect functionality or performance. Over the years, surface treatments have been developed to compensate certain flaws or weaknesses in manufactured products. Combining surface treatments with the modularity of additive manufacturing could lead to more adaptable and creative improvements of product functions in the future. The current work evaluates the feasibility of pursuing a new research axis in …

Numerical Study Of Solar Receiver Tube With Modified Surface Roughness For Enhanced And Selective Absorptivity In Concentrated Solar Power Tower, Shawn Hatcher, Mathew Z. Farias, Jianzhi Li, Peiwen Li, Ben Xu

Manufacturing & Industrial Engineering Faculty Publications and Presentations

Concentrated solar power (CSP) is a reliable renewable energy source that is progressively lowering its cost of energy. However, the heat loss due to reflected and emitted radiation hinders the maximum achievable thermal efficiency for solar receiver tubes on the solar tower. Current solar selective coatings cannot withstand the high temperatures that come with state-of-the-art CSP towers often needing to be recoated soon after initial operation. We intend to use Inconel 718 with different additive manufacturing (AM) practices to construct surfaces that allow for more light-trapping to occur. By adjusting printing parameters, we can tailor a surface to allow for …

Multifunctional Additive Manufacturing And Multiphysics Numerical Investigations Of Carbon Fiber Structural Battery Composite Using A Drop-On-Demand Method With In-Situ Consolidation, Xiangyang Dong, Yuekun Chen

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Lightweight Carbon Fiber Structural Battery Composite Has Great Potential in Increasing Structural Energy Storage Efficiency for Multifunctional Applications. However, It is Still Challenging to Design Carbon Fiber Multifunctional Composite Due to Lack of Proper Manufacturing Methods. in This Study, an Integrated Multifunctional Design and Fabrication Approach is Developed by Combining a Drop-On-Demand Additive Manufacturing Method with a Multiphysics Numerical Model to Guide the Development of the New Multifunctional Composite. through Deposition with In-Situ Consolidation, the Function and Thickness of Each Carbon Fiber Layer as Well as its Fiber Volume Fraction Are Accurately Controlled. Decreasing Layer Thickness Improves Flexural Properties. the …

Point Heat Source Correlation To Microstructural Evolution In Advanced Manufacturing, Mark Anderson

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Although there are different ways that advanced manufacturing can be performed, the use of single-point heat sources has become the standard to control a final product’s properties. It is imperative to understand how the heat source used in the different advanced manufacturing processes affect the microstructure of interest. The intimate relationship between the heat source and microstructure allows for controlling and tailoring a part’s properties. Utilizing different microstructural analysis, the cross-correlation of various point heat sources to developed microstructure was conducted in this dissertation.

Laser powder bed fusion allows for unique print-to-part protocols, but the dynamics of the process makes …

Experimental And Numerical Studies Of Slurry-Based Coextrusion Deposition Of Continuous Carbon Fiber Micro-Batteries To Additively Manufacture 3d Structural Battery Composites, Aditya R. Thakur, Xiangyang Dong

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Carbon Fiber Structural Battery Composites Have Recently Attracted Growing Interests Due to their Potentials of Simultaneously Carrying Mechanical Loads and Storing Electrical Energy for Lightweight Application. in This Study, We Present a Slurry-Based Coextrusion Deposition Method to Additively Manufacture 3D Structural Battery Composites from Carbon Fiber Micro-Batteries. Cathode Slurry is Coextruded Together with Solid Polymer Electrolyte-Coated Carbon Fibers in a Single Deposition. a Network of Carbon Fiber Micro-Batteries is Achieved within the Fabricated Structural Battery Composites. Electrochemical Tests Show a Stable Charge-Discharge Performance Up to 100 Cycles. the Rheological Behavior of the Cathode Slurry is Found to Govern the Coextrusion …

Heterogeneous Sensor Data Fusion For Multiscale, Shape Agnostic Flaw Detection In Laser Powder Bed Fusion Additive Manufacturing, Benjamin Bevans, Christopher Barrett, Thomas Spears, Aniruddha Gaikwad, Alex Riensche, Harold (Scott) Halliday, Prahalada Rao

Department of Mechanical and Materials Engineering: Faculty Publications

We developed and applied a novel approach for shape agnostic detection of multiscale flaws in laser powder bed fusion (LPBF) additive manufacturing using heterogenous in-situ sensor data. Flaws in LPBF range from porosity at the micro-scale (< 100 μm), layer related inconsistencies at the meso-scale (100 μm to 1 mm) and geometry-related flaws at the macroscale (> 1 mm). Existing data-driven models are primarily focused on detecting a specific type of LPBF flaw using signals from one type of sensor. Such approaches, which are trained on data from simple cuboid and cylindrical-shaped coupons, have met limited success when used for detecting multiscale flaws in complex LPBF parts. The objective of this work is to develop a heterogenous sensor data fusion …

Pcl And Dmso2 Composites For Bio-Scaffold Materials, Jae-Won Jang, Kyung-Eun Min, Cheolhee Kim, Chien Wern, Sung Yi

Mechanical and Materials Engineering Faculty Publications and Presentations

Polycaprolactone (PCL) has been one of the most popular biomaterials in tissue engineering due to its relatively low melting temperature, excellent thermal stability, and cost-effectiveness. However, its low cell attraction, low elastic modulus, and long-term degradation time have limited its application in a wide range of scaffold studies. Dimethyl sulfone (DMSO2) is a stable and non-hazardous organosulfur compound with low viscosity and high surface tension. PCL and DMSO2 composites may overcome the limitations of PCL as a biomaterial and tailor the properties of biocomposites. In this study, PCL and DMSO2 composites were investigated as a new bio-scaffold material to increase …

Fast-, Light-Cured Scintillating Plastic For 3d-Printing Applications, Brian G. Frandsen, Michael Febbraro, Thomas Ruland, Theodore W. Stephens, Paul A. Hausladen, Juan J. Manfredi, James E. Bevins

Faculty Publications

Additive manufacturing techniques enable a wide range of possibilities for novel radiation detectors spanning simple to highly complex geometries, multi-material composites, and metamaterials that are either impossible or cost prohibitive to produce using conventional methods. The present work identifies a set of promising formulations of photocurable scintillator resins capable of neutron-gamma pulse shape discrimination (PSD) to support the additive manufacturing of fast neutron detectors. The development of these resins utilizes a step-by-step, trial-and-error approach to identify different monomer and cross-linker combinations that meet the requirements for 3D printing followed by a 2-level factorial parameter study to optimize the radiation detection …

Non-Destructive Infrared Thermographic Curing Analysis Of Polymer Composites, Md Ashiqur Rahman, Javier Becerril, Dipannita Ghosh, Nazmul Islam, Ali Ashraf

Mechanical Engineering Faculty Publications and Presentations

Infrared (IR) thermography is a non-contact method of measuring temperature that analyzes the infrared radiation emitted by an object. Properties of polymer composites are heavily influenced by the filler material, filler size, and filler dispersion, and thus thermographic analysis can be a useful tool to determine the curing and filler dispersion. In this study, we investigated the curing mechanisms of polymer composites at the microscale by capturing real-time temperature using an IR Thermal Camera. Silicone polymers with fillers of Graphene, Graphite powder, Graphite flake, and Molybdenum disulfide (MoS₂) were subsequently poured into a customized 3D printed mold for …

Performance Evaluation Of Composite Sandwich Structures With Additively Manufactured Aluminum Honeycomb Cores With Increased Bonding Surface Area, M. Rangapuram, S. K. Dasari, Joseph William Newkirk, K. Chandrashekhara, H. Misak, P. R. Toivonen, D. Klenosky, T. Unruh, J. Sam

Materials Science and Engineering Faculty Research & Creative Works

Modern aerostructures, including wings and fuselages, increasingly feature sandwich structures due to their high-energy absorption, low weight, and high flexural stiffness. The face sheet of these sandwich structures are typically thin composite laminates with interior honeycombs made of Nomex or aluminum. Standard cores are structurally efficient, but their design cannot be varied throughout the structure. With additive manufacturing (AM) technology, these core geometries can be altered to meet the design requirements that are not met in standard honeycomb cores. This study used a modified aluminum honeycomb core, with increased surface area on the top and bottom, as the core material …

Experimental Approach For Development Of A Powder Spreading Metric In Additive Manufacturing, M. Hossein Sehhat, Austin T. Sutton, Zane Yates, Ming-Chuan Leu

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The Powder Spreading is a Vital Step of Powder-Based Additive Manufacturing (AM) Processes. the Quality of Spread Powder Can Considerably Influence the Properties of Fabricated Parts. Poorly Packed Powder Beds with High Surface Roughness Result in Printed Part Layers with Large Porosity and Low Dimensional Accuracy, Leading to Poor Mechanical Properties. Therefore, the Powder Spread ability and its Dependence on Process Parameters and Powder Characteristics Should Be Quantified to Improve the Efficiency of Powder-Based AM Methods. This Study Proposes a Novel Dimensionless Powder Spread Ability Metric that Can Be Commonly Used in Different Powder-Based AM Processes. the Quality of Spread …

Exploring Additive Manufacturing In A Space Environment - A Capstone Design Project Experience, Zain Zafar Khan, Zachary Alan Sobelman, Sharanabasaweshwara Asundi

Mechanical & Aerospace Engineering Faculty Publications

The employment of additive manufacturing in the non-standard environments like space, ships, or submarines has the potential to be an advanced utility not only in the pre-flight production of aerospace components and structures, but also for the onboard manufacturing of components and tools necessary for future space missions. For example, the ability to produce tools and structural components on the International Space Station can provide the space community the opportunity to make repairs and upgrades to the space station without wasting time and resources transporting such materials through additional missions. Additive manufacturing would allow for space missions to use on …

Advances In Precision Microfabrication Through Digital Light Processing: System Development, Material And Applications, Xinhui Wang, Jinghang Liu, Yang Zhang, Per Magnus Kristiansen, Aminul Islam, Michael Gilchrist, Nan Zhang

Articles

Digital Light Processing (DLP) is an advanced additive manufacturing technology which has garnered substantial recognition and has been extensively applications in various fields. This review focuses on the precision microfabrication process of DLP, providing an overview of the DLP 3D printing system, including the digital light engine, project lenses, motorised stage and resin vat for micro-structure fabrication. Additionally, this review paper comprehensively analyses commercially available DLP printers, covering resolution, cost and a detailed discussion on the importance of photopolymer resins, emphasising the monomer, photo-initiator, photoabsorber, etc. Based on the photopolymerisation theory, the DLP high-precision printing process is analysed, which is …

Additively Manufactured Carbon Fiber- Reinforced Thermoplastic Composite Mold Plates For Injection Molding Process, C. Bivens, A. Wood, D. Ruble, M. Rangapuram, S. K. Dasari, K. Chandrashekhara, J. Degrange

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Polymer injection molding processes have been used to create high-volume parts quickly and efficiently. Injection molding uses mold plates that are traditionally made of very hard tool steels, such as P20 steel, which is extremely heavy and has very long lead times to build new molds. In this study, composite-based additive manufacturing (CBAM) was used to create mold plates using long-fiber carbon fiber and polyether ether ketone (PEEK). These mold plates were installed in an injection molding machine, and rectangular flat plates were produced using Lustran 348 acrylonitrile butadiene styrene (ABS). Tensile and flexural testing was performed on these parts …