Engineering Commons^™

A Smart Internet Of Things (Iot) Prototype For Accurate People Counting Towards Energy Efficient Buildings, Qian Huang, Kane Rodriguez, Chao Lu

ASA Multidisciplinary Research Symposium

According to the U.S. Department of Energy, 30% of the energy used in commercial buildings is wasted. If the number of humans in each pre-determined thermal zone is aware, a building automation system (BAS) is able to intelligently adjust HVAC operation for each thermal zone to provide “just-enough” heating, cooling and ventilation to building users. Therefore, a people counting device that can be widely deployed with low price and failure rate, small form-factor, good usability, and conserved user privacy is highly desirable. Existing room occupancy detection sensors (e.g., passive infrared, camera, acoustic, RFID, CO₂) cannot meet all these …

Factors Influencing Student Selection Of A Collegiate Aviation Program, Matthew J. Romero, Jose R. Ruiz Ph.D.

ASA Multidisciplinary Research Symposium

This study aims to identify the most influential characteristics that drive undergraduate students to select collegiate aviation flight programs in the US. Using preference aggregation techniques, a list of the most influential attributes is created as a result of the investigation.

Fdm Machine Learning: An Investigation Into The Utility Of Neural Networks As A Predictive Analytic Tool For Go Around Decision Making, John Bro

ASA Multidisciplinary Research Symposium

FDM MACHINE LEARNING: An investigation into the utility of neural networks as a predictive analytic tool for go around decision making.

Investigation Of Ternary Binder Based Systems In Terms Of Calorimetry, Shrinkage And In-Situ Xrd, Anxhelina Qorllari, Elsa Qoku, Thomas A. Bier, Teuta Dilo

UBT International Conference

Ternary binders are defined in this study as compositions of Calcium Aluminate Cement (CAC), Ordinary Portland Cement (OPC) and Calcium Sulfate (CS̅). Several mixtures were studied, calorimetric and shrinkage technique has been used to follow the hydration during 24 hours. The XRD technique is used as support in the analysis of the hydration products. The results have shown that the initial amount of ��� and �� play a key role in the hydration of ��/���/�� mixtures and especially affect the formation of ettringite. The mechanism of reactions (hydration kinetic) and the reactions speed (acceleration or retardation) depends by the aggregates …

Reducing The Porosity And Sealing Cracks By Using Crystalline Admixture In Conventional Concrete, Visar Krelani, Liberato Ferrara

UBT International Conference

There is a continuous increase of quality on civil engineering materials in developed countries and parallel increase of need for new constructions in developing countries. Professional community should propose solutions for the durability that can resist in different severe environments. The most important factor that can affect concrete durability is represented by the pore distribution. Transport properties can take place through the porous network inside the cementitious composites and the aggregates interface, permitting the ingress of aggressive agents damaging concrete function intrinsically as a material and the wellfunctioning of the entire structure. The use of a crystalline admixture during the …

Using Of Proper Pavement Material For The Intersections With Slow-Moving Traffic, Bekim Selimi

UBT International Conference

Use of proper pavement material for some of intersections need special attention by road designers. At Camp Bondsteel-Kosovo on 2002 were built four road intersections using the concrete as pavement material. Heavy and slow-moving trucks that are turning or accelerating exposed these intersections to some of the highest stress level. After some years this intresections start deteriorating on their surface due to friction. The concrete pavements did not survive this period of usage and after eight years were removed and replaced with asphalt pavements. After more than seven years, the asphalt has shown minor distress but is still in good …

Developing A New Total Sediment Transport Formula, Davut Okeu, Sokol Xhafa, Sevdije Govori, Majlinda Daci

UBT International Conference

Sediment transport is one of the most powerful factor on river hydrology. It has vital importance for water engineering projects. There are many sediment transport formulas in the literature but most of them are derived from small data sets of natural rivers or experimental designs. Each formulation has its own restrictions, which depends on the original dataset of that study. None of them have gained universal acceptance. As a result, investigation towards the development of more accurate and simpler formulae is still necessary and should be continued.

The aim of this study is to derive a new total sediment load …

Heritage Under Pressure The Case Of The “Bypass” In Gjirokastra World Heritage Site Albania, Kreshnik Merxhani, Valmira Bozgo

UBT International Conference

The following article is an account presenting a professional movement opposing a planned and approved project for the construction of a new road known as the “Bypass”, which endangered the Historic Center of Gjirokastra. The project, consisted in the construction of a new road, with the initial aim of diverting automobile traffic from the Bazaar, turning it into a pedestrian zone. However after a few procedural problems were noted, it became clear that the project itself was not fulfilling its original aim, and further more posed a threat to the historical center. During the only public consultation session held for …

The Influence Of The Radius Of The Curve And The Lateral Slope On The Safety Of The Vehicle, Baxhuku Visar, Koca Odisea, Çekiçi Visar

UBT International Conference

The movement of the vehicle in a curve related to the construction of the road is expressed through the influence of the radius of the curve and the transversal inclination of the road. Two of these quantities are fixed quantities ever since the projection and then construction phase of the road. During the vehicle’s movement in the curve, their influence is shown through the critical slide velocity. This critical velocity is defined from the influence of the centrifugal force. For smaller values under critical velocity, this influence is expressed through the safety of the movement or the comfort of the …

Negative Impacts (Sbs) In Residential Buildings Case Studies From Kosovo, Muhamet Ahmeti, Mimoza Sylejmani

UBT International Conference

This paper presents the negative impacts on residential buildings in Kosovo, - as well as the main factors of the occurrence of sick building syndrome (SBS) in residential buildings in the case of Kosovo. It also examines the impact of different materials on this phenomenon and how many constructions in Kosovo are protected from this phenomenon.

For the assessment of the impact of materials on health and the environment, it is necessary to consider all the phases. Starting from the phase of construction, selection of materials, application from the beginning of the use of the building, including all the materials …

The Effect Of Particles Pm10 And Pm2.5 In Dust Emission Of Urban Infrastructure From Thermal Power Plant Technology Kosovo, Afrim Syla

UBT International Conference

Airborne particulate matter with aerodynamic diameters less than 10 microns (referred to as PM10) is one of the six criteria pollutants used by the U.S. Environmental Protection Agency as indicator of air quality. During the last decade, the health effects of urban aerosols have become a major concern for the society.

The main environmental problems in Kosovo include all issues related to water supply and sanitation system, air quality, solid waste management and urban infrastructure. The major problem remains high pollutions, energy losses and low collection efficiency. The awareness of environmental issues among the general public is poor. Air quality …

Seismic Actions Induced By Cladding Panels On Precast Concrete Frame Structures, Bruno Del Lago, Francesco Foti, Luca Martinelli

UBT International Conference

The strong earthquakes occurred in Southern Europe in the last decade pointed out a poor seismic performance of the connection system of the cladding of precast industrial structures. The cladding of these buildings usually consists of sandwich concrete panels of remarkable mass, connected to the frame structure with mechanical devices. The estimation of the out-of-plane seismic action on these connections is a key step for their correct proportioning. However, the formulation currently provided in the Eurocode 8 for the estimation of the seismic action on non-structural elements was calibrated with different objectives. Furthermore, given there is no in-plane structure-panel interaction, …

Capacity Design For R/C Structures According To En 1998-1:2004, Xhemshir Mulliqi

UBT International Conference

Capacity Design is a design process in which it is decided which objects within a structural system will be permitted to yield (ductile components) and which objects will remain elastic (brittle components). Material nonlinearity need only be modeled for ductile components, while components which will not yield need only consider elastic stiffness properties. In this design philosophy the capacity design approach that is currently used in practice demands strong column/weak beam frames or wall equivalent dual frames, with beam sway mechanisms, trying to involve plastic hinging at all beam ends.This paper aims to present Capacity design procedure for reinforced concrete …

P.M. 2.5 And Air Pollution In Prishtina, Rushiti Bardh, Futko Annea, Zeka Blin, Musliu Afete

UBT International Conference

High concentration of fine particles, the primary concern of worsening air pollution in Prishtina is believed to be fast paced economic and infrastructural growth in the capital of Kosova. This study is mainly focused on measuring the fluctuations of one constituent of air pollution, P.M. 2.5 (which are particles ranging from 2.5 to 10 micro-meters suspended into the environment). The measurements were done in Prishtina, mainly in the parts more frequented by people. Exposed to mixed combustion emission from roads with traffic, construction areas, and/or burning trash are a case of peculiar concern to people near those places. However, due …

Optimal Design Of Grillage Structures With Steel Crossed Beams Using Genetic Algorithms, Ersilio Tushaj, Niko Lako, Fatjon Saliu

UBT International Conference

The optimal problem in the structural design is an important issue in the engineering design. Various authors have analyzed the optimization of steel structures using algorithmic approaches. These techniques are generally grouped in deterministic or meta-heuristic techniques. From the introduction of structural optimization in the 1960’ up to now, various methods have been proposed. A genetic algorithm, is built and applied in this study using MatLab soft R2017a to a crossed beams system. The structural analysis is done with the direct stiffness method with constraints verification based on EuroCode 3:2005 criteria. Results are reported in the study.

Beam- Column Joints For R/C Structures According To En 1998-1:2004, Xhemshir Mulliqi

UBT International Conference

Joints are crucial zones for the transfer internal forces effectively between the connecting elements like beams and columns .The behaviour of reinforced concrete moment resisting frame structures in recent earthquakes all over the world has highlighted the consequences of poor performance of beam column joints. The basic requirement of design is that the joint must be stronger than the adjoining hinging members, usually the beams or columns. This paper aims to present design approach for Beam- Column joints for reinforced concrete (R/C) structures according to the EN 1998-1:2004.

The Effect Of Elevated Temperature On The Lightweight Concrete Containing Waste Pet Aggregate, Semiha Akçaözoğlu

UBT International Conference

In this study, the effect of waste PET as lightweight aggregate (WPLA) replacement with conventional aggregate on the some physical and mechanical properties and residual compressive strength of concrete was investigated. For this purpose, five different mixtures were prepared (the reference mixture and four WPLA mixtures including 30%, 40%, 50% and 60% waste PET aggregate by volume). The fresh and dry unit weights, compressive strengths, flexural-tensile strengths, water absorption and porosity ratios of the mixtures were measured. In addition the specimens exposed to elevated temperatures at 150, 300 and 450 °C and the residual compressive strengths were measured. Test results …

The Effect Of Fine Material Amount On Optimum Water Content Of Roller Compacted Concrete, Kubilay Akçaözoğlu, Bedrettin Menemencioğlu

UBT International Conference

In this study the effect of fine material amount on the optimum water content of roller compacted concrete (RCC) was investigated. The fine aggregate was replaced with calcite which maximum particle size was 63 μ, in amount of 0%, 2%, 4%, 6%, 10% and 14% by weight of total aggregate. Six different mixtures were prepared in the study. The optimum water contents of the mixtures were determined by using modified proctor test. Optimum water content, maximum dry unit weight and maximum fresh unit weight of produced specimens were measured. Optimum water content of specimens decreased depending on increasing fine aggregate …

Research On System Communication By Using Unified Registry Model & Elements, Kujtim Gashi, Atdhe Buja, Fatos Idrizi

UBT International Conference

Trends of Development of Information Society in the Republic of Kosovo must fit the criteria and standards of the EU. The main objective of the paper is the identification of individual IT systems used by the Republic of Kosovo public institutions related to the trade and working out analysis and recommendations for optimizing their communication (interoperability), eventual unification in the hardware & software level and increase the efficiency of the entire economic system information. The analytical analysis outlined these points, as it follows: current technologies used by public administration of the Republic of Kosovo, risk analysis, analysis of data structures …

Smia: Improving Kosovo's Education Management System, Lazar Adjijgogov, Dejan Stamenov, Edmond Jajaga

UBT International Conference

Successful management of today’s education systems requires effective policy-making and system monitoring through data and information. To this end, countries around the world have invested significant resources into collecting, processing, and managing more and better data through education management information systems (EMIS). SMIA is a modern EMIS, which offers easier management of educational process in Kosovo. It facilitates decision-making, resource planning, strategy building, monitoring and evaluation of educational system through a rich set of analytical and statistical tools. For over six years of activity, the system has efficiently tracked and thus helped the development of the educational process for every …

Evaluation Of Physical - Chemical Contaminants In Lumbardhi River In Prizren For The Period May - June 2017, Gashi Sami, Bajmaku Ymerr, Besar Veseli, Drini Petrit

UBT International Conference

This paper covers the monitoring of water pollution in the river basin from the source to the White Drin flow monitoring the river flow both in the rural and urban areas of water quality. The biggest problem in environmental protection is the quality of surface water. The results from the analysis of the study will serve to know the pollution from these physical-chemical parameters and at the same time to manage the eco-status in order to prevent negative trends and create a desirable balancing of so important the ecosystem as it is the system consist of Lumbardhi River, with biodiversity …

Monitoring Of Air Quality In The Urban And Industrial Areas In Kosovo, Besa Veseli, Sami Gashi, Shkumbin Shala

UBT International Conference

Environmental pollution has a direct or indirect effect, and is mainly caused by human activity or environmental processes that have harmful effects in the environment and human life.In Kosovo the air pollution in Kosovo is quite evident in the industrial areas. The power plant of KEK (TCA and TCB), from the Cement Factory and ferronickel etc.

In the vast majority of cases, the pollution is caused by the emission of sulfur dioxide (SO2), azotes (NOx), ozone, lead and other heavy metals, such as carbon monoxide (CO), dust, PM10,PM2,5 and steamy organic components.

The aim of this inquiry is to study …

Improving Efficiency, Reduction Of Pollution And Co2 Emission From Power Plant Kosovo, Afrim Syla

UBT International Conference

In recent years, global warming has been a major issue due to continuous growth of greenhouse gas emissions from different sources. Earth’s atmosphere is composed of a variety of chemical compounds that act as greenhouse gases. Carbon dioxide (CO2) is of primary concern due to growing global emissions in recent history. Since the expansion of coal use during the industrial revolution and the expansion of petroleum use during the 20th century, CO2 emissions have risen steadily.

The major factor in Kosovo’s political, social, and economic life today is the development and social sustainability. The biggest challenge for Kosovo remains the …

Evaluation Of The Ereniku River Waters In The Locations Where The Lukac River Flows, Faton Maloku, Luan Daija, Xhelal Këpuska

UBT International Conference

The fate and transport of many anthropogenic pollutants have an impact not only on hydrological cycles, but also on physico-chemical processes.Water resource monitoring will assess the quality of water, identify its depreciation, and help policymakers make decisions that will preserve not only natural areas but also improve quality of life.Therefore the purpose of this paper is to evaluate the physical and chemical parameters of the locations where the river Lukac flows into the Erenik river. Erenik is a river in the western part of Kosovo.The water quality of the Ereniku river comes from anthropogenic activities, mainly from sewage discharges, from …

Economic Aspect Of The Electricity Production In Subsidiary Mpc Oslomej, Imer Zenku

UBT International Conference

The need to increase the production of electricity in the Subsidiary MPC Oslomej (Mining Power Complex-Oslomej), which operates as part of JSC ELEM (Macedonian Power Plants), 100% state owned company, represents a significant economic activity.

Therefore, the analysis in this paper focuses and aims at the economic aspect of the current electricity production, that is, the impact of the expenditures of the Subsidiary on the price of electricity produced by ELEM JSC, a price also regulated by the Energy Regulatory Commission of the Republic of Macedonia (ERC).

This shall draw attention to the necessity to timely prepare and adjust the …

Study Of The Power Consumption Of Pseudo Random Bit Generator Circuits Implemented On Fpga, Galia Marinova

UBT International Conference

Pseudo Random Bit and Number Generator (PRB/NG) circuits being very widely used for security, compressive sensing and diverse other applications in telecommunications are studies in different aspects in the laboratory of Computer-aided Design in Telecommunications in Technical University-Sofia. Some results of this study are published in [1] where tests for randomness from the National Institute of Standards and Technology (NIST) suit are applied on commonly used PRB/NGs. Other aspects of the PRB/NG circuits study is their power consumption in the aim of green communications as noticed in [2,3] and the concern about low power consuming devices for Internet of Things’ …

Computer Science: Application Of Technology/Iot In Hydropower Dams, Orjola Jaupi

UBT International Conference

As time passes by, we barely see how much time it costs people to stay at work, fixing problems that happen every day. As people we should do more about humanity and technology is the door that opens opportunities for us to do this. Technology today is transforming every human daily life routine and it’s only the beginning of what technology can bring. By 2020 we know that technology will connect the unconnected by introducing the real idea of Internet of Things. Every little, tiny thing all over the world will be connected, but also big and important projects like …

Review Of Artificial Intelligence Development, Its Impact And Its Challenges, Litvane Spahija, Festim Halili

UBT International Conference

The field of Artificial Intelligence, which started roughly half a century ago, has a turbulent history. In the 1980s there has been a major paradigm shift towards embodiment. While embodied artificial intelligence is still highly diverse, changing, and far from “theoretically stable”, a certain consensus about the important issues and methods has been achieved or is rapidly emerging. In this paper we briefly characterize the field, summarize its achievements, and identify important issues for future research.

With the popularization of the Internet, permeation of sensor networks, emergence of big data, increase in size of the information community, and interlinking and …

Characteristics And Temporal Behavior Of Internet Backbone Traffic, Artan Salihu, Muharrem Shefkiu, Arianit Maraj

UBT International Conference

With the rapid increase demand for data usage, Internet has become complex and harder to analyze. Characterizing the Internet traffic might reveal information that are important for Network Operators to formulate policy decisions, develop techniques to detect network anomalies, help better provision network resources (capacity, buffers) and use workload characteristics for simulations (typical packet sizes, flow durations, common protocols).

In this paper, using passive monitoring and measurements, we show collected data traffic at Internet backbone routers. First, we reveal main observations on patterns and characteristics of this dataset including packet sizes, traffic volume for inter and intra domain and protocol …

Applying A Revised Approach Of Fuzzy Cognitive Maps On A Hybrid Electrical Energy System, Ekavi Antoniou, Eleni S. Vergini, Peter P. Groumpos

UBT International Conference

Complex systems modeling is a rapidly developing research field which incorporates various scientific sectors from bio medicine and energy to economic and social sciences. However, as the systems’ complexity increases pure mathematical modeling techniques prove to be a rather laborious task which demands wasting many resources and in many occasions, could not lead to the desired system response. This realization led researchers turn their attention into the field of computational intelligence; Neural Networks and Fuzzy Logic etc. In this way scientists were able to provide a model of a system which is strongly characterized by fuzziness and uncertainties. Fuzzy Cognitive …