Engineering Commons^™

Microprocessor Testing And Computer Aided Diagnosability Of Digital Circuits, Shirish Patel

Theses

Computer Aided Diagnosability Of Circuits (CADOC), a new method is developed for isolating and pin-pointing a faulty device in digital circuits. CADOC is based on graph-theoretic principle and PFD numbers. Without considering any SA1 or SAO faults, we can zoom out faulty device by selecting different diagnostic path to narrow down the faulty region and to isolate the faulty device. The efficiency of this new technique is confirmed by applying the technique to many examples.

3-D Reconstruction Of Microvasculature From High Voltage Electron Microscopy (Hvem) Data, Pradip Kumar Paul

Theses

This is a new method for histoarchitectural and volumetric analyses of cell compartments of microvasculature with the use of a unique combination of computerized 3-D reconstruction and HVEM thick serial cross sections. The technology is potentially a reliable, simple, accurate and fast method. Pioneering work in this area was started by Todd et al. (Circ Res Vol :53 p 319 ;1983) basically using light microscopy, but supported by conventional ultrathin transmission electron microscopy. These techniques are important in that they promise to resolve controversies in terms of evaluating the occurance of hyperplasia and hypertrophy in small resistance vessels in various …

Reliability Evaluation Of Liquid Crystal Displays Under Accelerated Test Conditions, Ishatdev Singh Rathore

Theses

This thesis deals with the recent study of reliability of liquid crystal displays. This study determined the effects of high temperature on LCD reliability. To accomplish this, reliability life testing was done on different kinds of LCD samples under different operating conditions. The tests were carried out on the samples of two different vendors at two different temperatures. No humidity was added in any test.

Vendor No. 1

1. 120 units at 77° ± l° C.

2. 80 units at 85° ± 1° C.

Vendor No. 2

1. 60 hard and 60 soft glass units at 77° ± 1°C.

2. …

Sorption Characteristics And Their Effects On Geotechnical Properties Of Clay Soils, Arambawattage Mahendra Rodrigo

Theses

An experimental investigation on the sorption characteristics of clay soils with liquid organics (phenol, chlorophenol, nitrophenol and chlorobenzene) and their effects upon geotechnical properties was undertaken. The investigation consisted of two different phases, namely, (1) the sorption/ desorption study, including kinetic rate, equilibrium time, isotherm modeling, and (2) geotechnical properties due to clay/ liquid organic interactions. The results of kinetic rate study indicate that the equilibration time for the contaminants way dependent upon the hydrophobic or the hydrophelic nature of the chemical. For equilibrium adsorption models, the linear isotherm was found to be the best fit in predicting sorption capacities …

Design And Development Of An Infrared Ccd Camera, John Frederick Romanowich

Theses

An infrared CCD camera system was designed and developed for operating various sizes of Schottky-barrier IR-CCD image sensor chips. The camera has a digitally programmable frequency synthesizer for operating the 160 X 244, 320 X 244, and 256 X 256 image sensors developed at the David Sarnoff Research Center. The electronics of the camera are designed to provide the outputs required for operating a XYZ monitor, a standard TV monitor, or a computer workstation. At the core of the camera design is a RS-170 standard sync generator that supplies the waveforms for synchronizing the camera's circuitry to produce a composite …

Design And Construction Of A Thermoelectric Calorimeter To Measure Thermal Resistance Of Building Components, Ravindra Samtaney

Theses

The steady-state thermal resistance of a building wall is an important parameter in determining its thermal performance. In-situ measurement of thermal resistance is the only unambiguous way of determining thermal resistance since the actual value may significantly differ from the laboratory or the calculated R-value.

Hitherto, the in-situ measurement of thermal resistance has been largely confined to the winter season. A thermoelectric calorimeter was designed, constructed and tested in order to provide measurements of thermal resistance during the summer as well as the winter season.

This thermoelectric calorimeter is a rectangular box, insulated on five sides and covered with an …

Study Of Dynamic Cmos Families And Development Of Certain Guidelines For Logic Synthesis, Vinay Santurkar

Theses

This work studies in detail two dynamic logic families, namely Zipper and Nora. It compares their performance using SPICE, a popular circuit simulator. Results show that a novel clocking scheme and a different latch circuit for the Nora pipelined structure can push its maximum clock rate of CMOS Dynamic circuits higher. It also ascertains whether the increased complexity of NORA is justified compared to the simpler Zipper circuit. It is shown that for very long logic chains, Nora works faster than Zipper. The work also presents some guidelines for synthesis of logic functions using CMOS Dynamic Cells. It shows that …

An Investigation Of Electrical And Physical Properties Of Reactively, Diode Sputtered Silicon Nitride Thin Films, Divyang Manharlal Shah

Theses

Silicon nitride thin films were deposited by r.f. reactive sputtering of silicon in nitrogen and argon discharge. Biased and unbiased modes of diode mode sputtering were used. Typical parameters for a sputter deposition run were: base pressure, 1-2x10-6 torr; sputtering pressure, 5-7 mtorr; nitrogen partial pressure, 15-16%; cathode-anode gap, 4 inch; r.f. power, 200-250 watts; cathode voltage, 1.8-2.1 V r.f.; water vapor pressure, 20-30% of the base pressure. The film thickness and the refractive index were measured by ellipsometery. The films of thickness 300-2500A, refractive index 1.9-2.1 and resistivity 10101Ω — cm were obtained. The deposition rate was in the …

Design Of An Experimental Apparatus To Measure The Charge And Mass Of Ionized Species In A Partially Ionized Cluster Beam Deposition System, Nitin K. Shah

Theses

The objective of this research was the design and construction of an experimental apparatus to investigate the size distribution of gallium clusters that can be emitted from a heated crucible with a 1 mm nozzle. This research work involved the design and construction of a partially ionized cluster beam (PICB) deposition system which would provide low charged particle background for retarding field analysis and cluster size measurements. The apparatus also allowed control of critical parameters on which the cluster size may depend.

The promise of PICB is based on the formation of clusters of adatoms, their ionization and their acceleration …

Integration Of Cad/Cam System Into A Waterjet Cutting Cell, Sanjay C. Shah

Theses

The work is intended to bridge the gap between CAD and CAM fora waterjet cutting cell. The output of CAD is used by CAM directly through the software interface developed. To achieve this, a postprocessor is designed for a two-dimensional system for the series 8200 Allen Bradley's 5-axes Robot Controller. Calma's DDM & DIMENSION III interactive graphics system implemented on VAX was used for the part design. The postprocessor is a computer program, written in the structured FORTRAN, that is unique for a given machine-tool/controller combination. The conversion of the coding and recording format of the APT file to the …

Investigation Of High Shear-Rate Viscoelastic Flow, Sudarshan S. Sood

Theses

The object of this study is to understand two important characteristics exhibited by viscoelastic fluids at high shear-rates, and analyse their influence on practical applications Viscoelastic fluids, such as polymer solutions, when subjected to high shear stress, behave in a manner which has not been sufficiently analytically explained In experimental studies, such fluids have shown.

(a) Stress relaxation.

(b) Decrease of viscosity with an increase in shear rate.

(c) Slight decrease of viscosity with temperature.

(d) Normal stress differences in shear flow.

In this thesis an analytical explanation is given for two (a and b ) of these features This …

Analysis And Simulation Of Chirp Radar System, Tina Tsung Tsai

Theses

This paper consists of a technique to design a Chirp radar system and proposes a solution to optimize the design of the linear time delay network required in such systems. A Chirp radar system has a wide bandwidth for high range resolution, and long pulse duration for high velocity resolution and high transmitted energy. The technique of a pulse compression system offers a means of increasing the average power available to illuminate radar targets without any loss of the resolution at the receiver needed for the tactical requirements of the system. This is accomplished by transmitting a wide pulse in …

Friedman's Model Of Calculating The Optimum Bid Price Using Dbase Iii Plus, Selim Uzel

Theses

The micro-computer program, BIDCALC presented in this thesis is offered as simple, practical, and proven approach to developing an effective data-based competitive bidding strategy. BIDCALC is written in dBASE III Plus programming language for MS-DOS based computers.

Main purpose of the program is to evaluate the optimum bid using the Friedman's model of Maximizing the Expected Profit. At the same time the program keeps track of necessary competitor and project information in data base files which are easily transferable to other software packages. The program is capable of generating a variety of reports in a matter of seconds.

BIDCALC is …

Cmos Sram Design For Initializing Programmable Logic Devices, Ravi K. Vaidyanathan

Theses

This thesis presents the design of CMOS Static Random Access Memory (SRAM) which is imbedded within a high performance Programmable Logic Device (PLD). The SRAM and its control circuitry are used to initialize (or personalize) the NJIT PLD chip. The design is defined in 3-levels of functional hierarchy consistent with the physical and electronic design automation utilized for this design. The imbedded SRAM supports the PLD application circuit which includes 8 small Array and one large Control Programmable Logic Arrays.

The SRAM is structured as 64 X 138 bit array with serial read and write inputs. It is designed emphasizing …

Automatic Generation Of Robot Paths For Waterjet Cutting From Autocad Drawings, Samir Vij

Theses

The automatic generation of robot paths for a commercial water-jet cutting system by establishing a link with a commercial CAD system, in an attempt to achieve paper-less manufacturing and to minimize human interface is the objective of this thesis.

Water-jet cutting is an emerging technology with unlimited potential for a wide variety of manufacturing applications. Water-jet cutting systems integrated with robotic work cells allow the user to cut a variety of parts through part programs generated for robot controllers. The system employed is an Ingersoll-Rand water-jet cutting system, the movement of which is controlled by an Allen-Bradley 8200R programmable robot …

Investigation Of The Characteristics Of The Kerf And The Surface Generated In The Course Of Cutting Titanium With Abrasive Waterjets, Ajay Vora

Theses

The effect of cutting parameters on the quality of cut in the course of cutting Titanium (Gr.2) with Abrasive Waterjet is investigated. The cutting parameters include nozzle traverse rate, size and feed rate of abrasives and nozzle(s) diameter. The width of kerf (top and bottom ), taper and roughness is studied. The measurements are tabulated and plots are made to study the trend and relationship for each set of parameters.

The qualitative conclusions are made successfully but no quantitative relationship was derived. Suggestions are made for the evaluation of technology for feasibility and economic justification, and to achieve desired cutting …

Analysis Of Spread Spectrum System Using Direct Sequence Technique In Jamming Environment, Kandarp A. Vyas

Theses

A spread spectrum system is a means of transmitting data over a channel In addition it offers a wide variety of features like data security and signal hiding This work studies in detail a spread spectrum system using direct sequence binary phase shift keying. The Sliding Correlator and Sequential Detector techniques have been used to achieve synchronization. A brief study of pseudorandom noise has been presented. System was simulated on UNIX using 'c'. A modified version, suitable for software implementation, of Sliding Correlator and Sequential Detector was, used. Results generated using tins model are presented here.

Temperature Dependent Reliability Of Plastic Packaged Microcircuits, Wasim Ahmed

Theses

Increasing power and power densities in new high complexity semiconductor devices are creating heat removal problems. Increased powers produce higher junction temperature which lead to potentially faster degradation of device reliability. Thermal management at device level packaging involves efficient and cost-effective removal of dissipated thermal energy from the device to assure its reliable performance over the long term. In the context of very high levels of integeration of future ICs, thermal management will mean making such devices possible close to the limits of acceptable high temperature.

The major factors affecting heat flow in a plastic Dual-in-line-packages (DIP'S) are investigated using …

Rf Characterization Of A Directly Modulated Ingaasp Buried Heterostructure Laser Diode, Charlotte Alvarez

Theses

The use of fiber optics for the transmission of microwave signals had its beginnings in 1984. Applications were limited to the lower microwave frequency regions. Technology in this field is advancing rapidly due to the high demand driven by the telecommunications community for high speed digital applications. Extensive research and development efforts are underway by both the component manufacturers and the subsystem end user. Most of the near term applications of microwaves in fiber optics are in weapon systems and communication systems for military and other government agencies.

The high frequency modulation characteristics of Lytel's InGaAsP 1300 nm buried heterostructure …

Design Of Bridge Inter-Connecting Token Ring & Token Bus Local Area Networks, Kasinath Anupindi

Theses

A Bridge interconnecting two Local Area Networks has been modelled. The two interconnected networks are the Token Ring and the Token Bus LANs. Concepts of Queueing theory have been employed in the design. Initially it is assumed that the buffer size at the Bridge is infinite. Further it is assumed that the arrival rate of the messages is Markovian and the service rate is General, Le it is an M/G/1 system. Expressions for the average waiting time at the Bridge and the size of the buffers is computed. Graphs for various parameters have been plotted. Based on these graphs the …

Comparison Of Various Techniques For The Detection Of Lines In 2-Dimensional Images, Somayajulu Bhamidipati

Theses

The detection of straight lines in 2-dimensional images leading to polygonal approximation to the boundaries of the objects is one of the important stages in scene analysis as it leads to the description of the images. The comparison of three diverse approaches for this problem in terms of the efficiency and accuracy is made, and their performance for different types of data and different sets of parameters is studied in this thesis.

The data points are generated using either an edge detection algorithm using chain encoding on real images or a synthetic data generator, which can create a variety of …

Data Flow Dependency Generator, Chin-Piao Chan

Theses

Data flow is a new approach to parallel computing. The concept is to enable the execution of an instruction whenever its operands become available. The only constraints in a data flow machine are the data flow dependencies between instructions.

In this thesis, a simulation package called the Data Flow Dependency Generator is developed. This package is designed to express the idea of data flow computations, the data flow dependencies and the use of multiprocessors.

Given a number of processors, a number of time units for each operation and a program, the Data Flow Dependency Generator finds the data dependencies between …

A 3-D Tactile Sensor With Digital Output, Sin-Shou Cho

Theses

This thesis details the design of a new tactile sensor for general-purpose robot manipulators. Such manipulators, designed to be functionally equivalent to the human hand, will require sensor arrays that fulfill several requirements : (1) many sensor elements to minimize tactile imaging time, (2) close spacing of small sensing elements for fine spatial discrimination, (3) ability to be molded to a convex fingertip surface for taction on concave surfaces, (4) tolerance to over-scale forces without damage. In addition to the above, which are considered requirements, several other characteristics are desirable. Foremost is the ability to sense shear forces, which provide …

Estimation Of Modified Proctor Densities Based On Visual Identification, Ramesh Damodaram

Theses

Often in construction jobs requiring controlled compaction, there is a delay involved in testing the soil sample to be used as a structural fill. Here a rational approach has been adopted to get these values from 600 test data available. Using these data, appropriate relationships between grain sizes, maximum dry densities and optimum moisture content were developed. From these, two tables were derived to estimate the maximum dry density and optimum moisture content based on grain size distribution.

In a fill control job, if the borrow pit happens to change, the field personnel could obtain soil samples and send them …

Implementation Of The Voice Processing System, Yang-Young Dan

Theses

The Voice Processing System is implemented by using XILINX Advanced Computer Aided Design Technology. It is also used as an interface to the 8052 AH-BASIC single hoard computer system.

The Voice Processing System ( VPS ) comprises three major parts:

1. Voice Detection Circuit

2. System Clock Generation & Synchronization

3. Signal Processing and Storing Circuit

The analog voice sip!gnals are the inputs to the first part of VPS. The digitalized voice is the output of this system.

In order to get precise output, the first part plays the roles of noise cancellation, zero crossing processing, and recognition.

For the …

Two Domain Heat Transfer Studies Using A Coupled Finite-Difference And Boundary Element Programs, Serap Dikmenli

Theses

An iterative coupling of a finite-difference boundary layer code "STAN5"' and a boundary element code "BEASY"2 have been used to study two dimensional convective-conductive problems. The coupling method essentially leaves undisturbed the codes of these programs and uses their custom features in their applicable domains. The boundary layer program is used-in the convective domain, while "BEASY" is used in the solid domain. Compatability conditions are established between these domain solutions and an iterative scheme is used until these conditions are mutually satisfied.

The indirect communication of compatability (boundary) criteria between these programs was achieved by two editor/data-transferor like programs. Combined …

Effects Of Peripheral And Microwave-Core Heating On Survival In Hemorrhagic Shock In Rats, Ashraf Sabry El-Assuooty

Theses

In a model of rats resuscitated from hemorrhagic shock,where 11 of 12 animals were alive up to 4 hours after shock, there was an average drop of 10°C in core body temperature. Survival and morbidity was much impaired when the shocked animals were externally heated with an infrared lamp to maintain a core body temperature of 35°C. Since the increased intrashock mortality is possibly due to the circulatory changes induced by peripheral heating, an attempt was made to determine the effects of heating the animal at its core. Twelve rats were shocked in the same fashion, however the body core …

Stepping Motor Control And Position Monitoring, Pei-Kuan Feng

Theses

Stepping motors provide precise digital control of speed, without speed detector feedback. A stepping motor can produce a large torque for a relatively small displacement, without a shaft-position sensor or special compensation. This provides accurate control of motor position. This thesis describes the development of stepping motor torque characteristics and the different approaches stepping motor phase current waveform detection. It is shown that one of the most useful indicators of rotor position is the initial rate of current rise. The Hybrid, Permanent-magnet and Variable-reluctance step motors have been applied in the drive circuits. The open-loop control circuits are implemented to …

An Investigation Of Interrupt Handling Schemes In Pipeline Processors, Shailesh Ratilal Gami

Theses

In order to acheive higher performance in a pipeline processor, proper interrupt handling is essential. In a pipeline processor, interrupt handling is difficult because many instructions are in the processor at the same time. This study describes and evaluates the different solutions to interrupt handling. Several pipelined 32-bit microprocessors have also been studied and their architectural and programming features are compared.

The Tapered Dielectric Rod-Conical Antenna, Nicholas I. Georghiades

Theses

The problem of the linearly tapered dielectric rod/conical antenna, excited by the HEI1 hybrid mode in a metallic circular waveguide , is rigorously studied. A theoretical model, and numerical investigation for the radiation characteristics of such an antenna are presented. The model is based on the combination of classical analysis of the Electromagnetic Fields within the dielectric rod, Local Mode Theory, and the Equivalence Principle for the determination of equivalent current distributions.

The far-zone radiation field is considered to be the summation of the fields produced by two radiative components in the dielectric rod/conical structure: The "aperture" of the uniform …