Engineering Commons^™

A Review Of Acetabular Prostheses For Total Hip Arthroplasty, Jennifer Anne Citarella

Theses

This study explores the evolution, design, and clinical progress of contemporary prostheses used in orthopaedic reconstruction of the socket of the hip joint. A literature search was performed to study acetabular implants, as used in total hip arthroplasty. The history of the design of these implants is chronicled. Next, the anatomy of the acetabular region and the surgical technique performed to replace the hip socket are presented. A comprehensive discussion of the design features, rationale, and clinical results for commercially available cemented and cementless prostheses follows.

Hydroxyapatite, a bioceramic which has just recently been approved for applications in total hip …

Properties And Determination Of Optimal Decentralized Feedback Structure, Kangsong Han

Theses

In this thesis, the decentralized feedback structure for large scale, linear time invariant systems is studied. The internal differences and the relationship between decentralized feedback structure and centralized feedback structure are discussed. The conventional diagonal feedback structure. corresponding to the classical single loop design strategy, is first analyzed. This is followed by an arbitrary decentralized information flow constraint which is dependent upon the actual plant characteristics. Although signal flow graphs have limited use in describing decentralized control systems. the concept of a control cycle unit based on signal flow is introduced as a supplementary tool to characterize some fixed modes …

Performance Of Different Strategies For Error Detection And Correction In Arithmetic Encoding, George F. Elmasry

Theses

Lossless source encoding is occasionally used in some data compression applications. One of these encoding schemes is the arithmetic encoding.

When data is to be transmitted via communication channel, noise and impurities imposed by the channel cause errors. To reduce the effect of errors, channel encoder is added prior to transmission through the channel. Channel encoder inserts some bits that help channel decoder at the receiver end to detect and correct errors. These added error detection and correction bits are redundancy that causes reduction in the compression ratio and hence an increase in data rate through the channel. The higher …

Polarimetric Fiber Optic Sensor For The Measurement Of Strain, Wei Ma

Theses

In this thesis, development of a Polarimetric Fiber-Optic strain sensor is presented. The sensor uses the phenomenon that strain can deform the probing part of the fiber and hence change the polarization of the transmitted light signal. By counting the resulting fringes, we can measure the exact strain in the material. Calibration of the sensor was achieved by setting up tension tests. Optical fibers were glued on the surface of the specimen. Reference strain gages were used to record the strain in the specimens. Resulting fringes from the fiber optic sensors were then related to the strain measured by the …

Design Of A 320x122 Mwir-Ccd Ptsi-Si Imaging Radiometer With Automatic Optical Integration Time Control, Nathaniel Joseph Mccaffrey

Theses

An infrared CCD camera system was designed and developed to operate a 320X244 Schottky-barrier IR-CCD Focal Plane Array (FPA) as an imaging radiometer. The goal of this research was to develop a reliable radiometer capable of resolving temperatures between 50 and 1000°C to within 1°C accuracy using non-contact spectral thermographic methods. To accomodate this wide dynamic range, the imager was operated in a non-interlaced format with variable optical integration times ranging from 120µsec to 122msec. Variable integration control was achieved by employing a "dump and read" timing procedure. To facilitate this operation, novel circuitry was developed for dynamically controlling the …

The Postbus Fault Tolerant Clos Network, Udayabhanu Sarangapani

Theses

The trend in modern computing is to develop multiprocessor systems with hundreds, even thousands, of processors and memory modules. The task of providing communication paths among all these units is not a trivial one. For a small number of functional units, direct connections could be used but for large systems interconnection networks have to be used. Multistage Interconnection Networks (MINs), provide a dynamic means for interconnecting processors and memory in a multiprocessor system. These networks are built with switches in each stage.

The Clos network is a well defined family of MINs and consists of three stages. The ordinary Clos …

Multilevel Embeddings For Massively-Parallel Hypercubes, Devenkuma P. Shah

Theses

Hierarchically structured arrays of processors have widely been used in the low and intermediate phases of image processing and computer vision. Since the pyramid structure efficiently supports local and global operations extensively required by these phases, it has been widely used for relevant algorithms. Multilevel systems keep all the advantages of the pyramid structure while providing a general hierarchical structure that is easier to be used for the development of several algorithms and may also provide higher performance.

Although the cost of pyramid machines may be tremendously high, they have limited applications. In contrast, the hypercube network is widely used …

Microengineered Mass Spectrometer With Field Emission Ionization Source, Chao Sun

Theses

This thesis describes a design for a microengineered mass spectrometer. This mass spectrometer device uses VLSI processing techniques to scale down the dimensions of an existing mass spectrometer and make it portable. It can be manufactured economically and has the potential to be integrated with more complex structures and including transistor integrated circuits. An optimized device is proposed. This device is to be fabricated using two silicon substrates approximately 1cm by 1cm, where one is a cathode electron source and the other is the ion collector. External ion sources are not needed. Electrons are emitted from the array of cathode …

Tantalum Silicide Variable Capacitance Rotary Micromotors : Design And Fabrication, Michael Steven Berry

Theses

Tantalum silicide was studied as an alternative microelectromechanical material by fabricating a rotary micromotor utilizing a proven design. This material was used for the rotor, stators, and bearing over a silicon substrate. It has the attraction of potentially reducing the friction which is a major problem with polysilicon-to-polysilicon bearings.

The necessity of high aspect ratio features required that a plasma or reactive ion etch with a high degree of anisotropy be developed to etch tantalum silicide films in excess of 1.5μm. A sulfur hexafluoride/Freon 115 plasma provided the necessary process control during the etches. The stress present in annealed tantalum …

Improving The Jitter Performance Of Timing Recovery By Employing Delay Shifts, Xin De Lu

Theses

Many methods have been developed for evaluating the jitter performance of timing recovery circuits for binary synchronous transmission systems. These circuits consist of a nonlinear device followed by a narrowband filter tuned to the pulse repetition frequency. This thesis introduce delay shifts in the timing recovery circuits to improve the jitter performance. The function of the delay shifts is analyzed and mathematical proof of jitter performance improvement is given for the system using square-law device. Finally, the numerical results obtained from the specific examples serve to illustrate the significant improvement between the system with and without delay shifts. That is, …

Investigation Of The Effects Of Methyl Chloride Addition On Premixed, Laminar, Methane/Air Flat Flames, Limin Wang

Theses

Temperatures and the concentrations of stable species, such as CO, CO₂, CH₄, and CH3Cl, have been measured over the height above burner at equivalence ratio of 0.79 (fuel lean) and 1.20 (fuel rich) for premixed, laminar CH₄/air and CH₃Cl/CH₄/air flat flames. A water-cooled quartz sampling micro-probe and gas chromatographic analysis were used for the concentration measurements. Chemical kinetic modeling of these flames with a 279-reaction, 63-species elementary reaction mechanism is performed using the CHEMKIN premixed flat flame code. The results of rate-of-production calculations are analyzed to determine the most important …

Modeling And Simulation Of Magnetic Micromotor Performance, Ping Wang

Theses

The objective of this research was to model the performance and optimize geometries for two types of magnetic micromotors: yoke-type (YTMM) and yokeless (YSMM). The two selected micromotor types matched the designs that have been described in the recent research literature. Modeling was accomplished using MAXWELL, an advanced 2-D and 3-D simulator. The micromotors with nickel and nickel-iron magnetic thin films for the rotor and stator were simulated for torque performance. Three-phase power supplies with overlapping and non-overlapping phases were used. Rotor diameter dimensions were varied from 285 to 600µm, and the rotor-stator air gap was varied from 3 to …

Modeling And Analysis Of Semiconductor Manufacturing Processes Using Petri Nets, Xinyao Wang

Theses

This thesis addresses the issues in modeling and analysis of multichip module (MCM) manufacturing processes using Petri nets. Building such graphical and mathematical models is a crucial step to understand MCM technologies and to enhance their application scope.

In this thesis, the application of Petri nets is presented with top-down and bottom-up approaches. The theory of Petri nets is summarized with its basic notations and properties at first. After that, the capability of calculating and analyzing Petri nets with deterministic timing information is extended to meet the requirements of the MCM models. Then, using top-down refining and system decomposition, MCM …

Modeling And Investigation Of Current Transport Phenomena In Schottky Structures, Yan Zeng

Theses

We have used a numerical method to describe the importance of the contribution of generation-recombination current to the I-V characteristics of Schottky barrier contacts. The current-voltage relationship is derived directly from the fundamental set of equations such as Poisson; current-density and continuity equations, without having to make many simplifications or approximations. The final result includes not only the thermionic emission or drift diffusion mechanisms of current flow, but also the generation recombination processes.

The experimental devices used for this work are very common low barrier height Schottky structures, Al/T_0.3W_0.7/n-Si/A1 and Ti_0.3W_0.7/n-Si/Al. The …

Study Of Emg Frequency Behavior, Mark Steven Fiedorowicz

Theses

It has previously been determined that the power spectral density of an electromyogram shifts towards lower frequencies over time during an isometric contraction. In this study the power spectral density curve was examined to see if changes would occur over a period of time as a subject walked on a treadmill at various speeds. The shapes of the power spectral densities recorded from the soleus shifted to the lower frequencies over time. The parameters associated with the curves showed trends. One of the parameters, zero crossing, demonstrated adaptation and fatigue in all four patients, for the first portion of the …

Integration Of Pneumatic Fracturing To Enhance In Situ Bioremediation, Conan Dante Fitzgerald

Theses

The purpose of this thesis was to study the anticipated benefits of integrating pneumatic fracturing with in situ bioremediation. Since pneumatic fracturing increases subsurface air flow in low permeability formations, it has the potential to overcome many of the major limiting factors of microbial growth and activity. A new innovation called pneumatic bio-injection can further enhance in situ bioremediation by efficiently dispersing biological solutions, including microorganisms, into a formation.

Bench scale experiments were conducted to examine the ability of microorganisms to survive the pressures and stresses associated with pneumatic injection. Tests conducted at pressures ranging from 60 to 500 psi …

A Multicompartmental Model For The Simulation Of Soluble Gas Exchange In The Lungs, Chitaranjan Varadhan

Theses

No abstract provided.

Computer Simulation Of Intracranial Hemodynamics During The Induction Phase Of Anesthesia, Gopinath P. Sundaram

Theses

The induction of general anesthesia is associated with severe hemodynamic compromises which, in turn, may cause acute elevation of intracranial pressure (ICP). Quantitative assessment of cerebrovascular responses arising from multiple mechanical and pharmacological interventions occurring in a short time interval require a large number of human studies which are difficult to perform. The purpose of this project is to evaluate the effect of various stimuli on the intracranial hemodynamics during induction using a mathematical model of cerebrovascular circulation.

A five compartmental model of the cerebrovascular system is used for our simulation. Autoregulation is modeled by adjusting arterial-arteriolar resistance in order …

Fracture Of Cementitious Composites, Sira Tindukasiri

Theses

Studies in fracture mechanics of concrete use a testing setup which tends to include unacceptably large errors in deflection measurements. Recent work reported by Kim [3] has proposed a new testing setup to eliminate these errors and consequently produce better determinations of fracture parameters.

The error which occurs most frequently is in the measurement of the load-line deflection. Until recently, the way this measurement has been made, using a dial gauge or LVDT (Linear Variable Differential Transformer) to measure the deformation between the center of the specimen and the frame, includes the crushing of the concrete surface at the supports …

An Implementation Of A Versatile Camera Calibration Technique For High-Accuracy 3d Machine Vision Metrology Using Off-The-Shelf Tv Camera And Lenses, Bolang Li

Theses

This thesis studies and implements a new versatile camera calibration technique for high-accuracy 3D machine vision metrology using off-the-shelf TV camera and lenses developed by Roger Tsai [1]. This technique builds up a unique relationship from the world coordinate system to the computer image coordinate system of calibration points by using a radial alignment constraint. The technique has advantage in terms of accuracy, speed, and versatility over existing techniques.

The fundamental knowledge for using this technique is presented in this thesis first, followed by an overview of the existing calibration techniques, and a detailed description of the new technique. The …

A Simulation Of A Monitoring And Alarm System In An Energy Management System, Hui-Jen Liu

Theses

This is a simulation for an energy system's monitoring and alarm and working under KEE's environment. Because of KEE's powerful capabilities, we can monitor and get warning signals from several active windows that we attaching them from KEE's system knowledge base to our source code.

It is very convenient for us to set every member of the energy system on an image panel. We can monitor the entire conditions of that member and get highlighted warning signals from its own image panel. Also we can initialize them by a kind of method-actuators windows if we want to restore the system.

Geometric Dimensioning And Tolerancing A Tool For Concurrent Engineering, Tapan Kumar S. K. Jain

Theses

The concept of Concurrent Engineering recognizes an immediate need for a new design environment and technology and so requires extensive interdisciplinary cooperation and integration of diverse functions of a manufacturing organization such as marketing, design, manufacturing and finance. One of the key factors to achieve successful integration among the departments is better communication and it becomes imperative in cases of varying levels of communication needs, especially in interdepartmental cases.

Concurrent Engineering is a philosophy which provides certain benefits. There are various tools and methods available for implementation of Concurrent Engineering concepts. One of the tools is Geometric Dimensioning & Tolerancing …

Comparison Of Heart Rate With Chest Wall Vibrations, Kofi M. Arbuah

Theses

A study is done using a Microwave Interferometer as a computer-assisted non-invasive cardiopulmonary monitor. The Microwave Interferometer is used to record the mechanical vibration of the anterior chest wall by recording the velocity of the displacement of the chest wall. The objective is to first, record mechanical vibrations of the anterior chest wall at different heart rates, and second, attempt to identify the relation between heart rate and chest wall vibration.

The system uses two channels, the first signal produced by the Microwave Interferometer is a record of the velocity of the displacement of the chest wall caused by the …

Power Consumption In Single-Phase Agitated Vessels Provided With Multiple Impellers, Gwo-Ming Chang

Theses

A significant amount of data can be found in the literature on power consumption of single-impeller agitation systems. However, little and incomplete information is available for power consumption in multiple-impeller systems. Therefore, the main objective of this study is to experimentally determine the power consumed by multiple impellers in mixing vessels as a function of impeller type, impeller off-bottom clearance, impeller spacing, and agitation speed.

In this work, the power dissipated by combinations of one, two or three impellers of either identical types or different types was studied. The power drawn by each individual impeller was measured by means of …

An Experimental Investigation Of Wear Behavior Of Ultra-High Molecular Weight Polyethylene Under Sliding Motion, Elham Zand-Moghaddam

Theses

This project investigates the effect of sliding motion on the materials that are used as bearing surfaces of human total-joint replacement prostheses.

The tests are performed with a specially designed equipment based on pin-on-disk machine. The testing machine is designed and constructed to reproduce sliding motion, applied to spherical ended metal "Canine-Head" components such as dog hip acting on a flat polyethylene surface. The sliding motion is performed by applying different constant loads for 5,000,000 cycles. The tests are carried out with the wear specimen lubricated by deionized water.

The purpose is to produce delamination, which is the severe wear …

A Mathematical Model For The Prediction Of Depth Of Cut In The Course Of Awj Machining, Naijian Ma

Theses

The objective of this study is to develop a practical mathematical model for prediction of the depth of cut in the course of Abrasive Water Jet (AWJ) machining. Semi-empirical method which is an integration of theoretical derivation and statistical analysis is used for process description. A theoretical model was constructed based on kinetic energy conservation equation, physical relationship among operating parameters, abrasive size, material properties and cutting results. Then, correlation between the depth of cut and operational parameters was analyzed in order to improve the theoretical model. Finally, a regression equation representing 1000 samples was constructed.

Three statistical criteria were …

Design And Development Of Flexible Manufacturing Cells - A Case Study, Behrouz Barzani

Theses

This paper covers the typical ills of American manufacturing companies and provides steps to selecting a flexible manufacturing cell(s) or system as a remedy. For that reason various definition of different types of flexibilities in manufacturing and the interrelationships between the several types have been examined. In addition, their purposes, means of obtaining them and some measurement and evaluations has been discussed. This was done to cover the basic but necessary requirements for understanding and selecting a flexible manufacturing system. Finally, the design process of a flexible system and its intuitive justification were discussed.

Mechanism Of Pneumatic Fracturing, Trevor Compton King

Theses

This thesis investigates the mechanism of pneumatic fracturing in geologic materials such as soil and rock. Pneumatic fracturing is a recently developed technique for increasing the permeability of geologic formations by the controlled injection of high pressure air. Present applications are focusing on the in situ remediation of contaminated soil and ground water, although pneumatic fracturing has other geotechnical uses such as pumping well enhancement.

A comprehensive literature review of a related technology known as hydraulic fracturing is presented, which serves as background for development of a pneumatic fracturing model. Pressure-time histories from actual pneumatic injections are analyzed in detail …

Aluminum Epitaxy On Silicon, Samuel Cruz Ramac

Theses

The purpose of this work was to study the effect of 4° miscut and chem¬ical pretreatment of Si(111) wafers on the epitaxial growth of Al by thermal evaporation in a UHV environment (~ 10^-9 Torr). Two chemical pretreatments of the wafers were used. One included HF only and the other included NH₄F after an initial HF treatment. The substrates were not heated dur¬ing deposition. XRD measurements of the films were done before and after annealing in a high vacuum oven for one hour at temperatures between 200 and 350°C.

The A1(200) films deposited on wafers pretreated with …

Simulation Of Manufacturing Cell Using Hoops Graphic Software And Siman Simulation Language, Parikh Vipul

Theses

Control of jobs being processed in manufacturing shop floor is important to management. The performance of job shop is affected by shop congestion due to arrival rate, batch size, number of machines, buffer capacity, process time variation, and dispatching rules use to load the jobs on the machine.

The job shop is a very complex system and hence, it is difficult as well as time consuming to obtained result using analytical method. A SIMAN simulation language is used to create generic model of a manufacturing cell and simulation analysis of those parameters variation such as job shop efficiency, the average …