Engineering Commons^™

Surface Modification Of Tin Oxide Nanoparticles By Atomic Layer Deposition For Enhanced Electrochemical Performance, Sai Abhishek Palaparty

Masters Theses

"Atomic Layer Deposition is a robust technique used to deposit high quality, conformal, and size-tunable ultrathin films on a substrate. This technique can be used to coat protective films on battery anode and cathode materials for enhanced performance. In the case of cathodes, the ultrathin film provides a protective barrier preventing cationic dissolution. In the case of anodes, the film acts as a supporting matrix reducing strain caused by volume expansions. In these study, we use this technique to coat an optimally thick conductive iron oxide film on tin oxide particles to improve its electrochemical performance at high current densities …

Event-Sampled Direct Adaptive Neural Network Control Of Uncertain Strict-Feedback System With Application To Quadrotor Unmanned Aerial Vehicle, Nathan Szanto

Masters Theses

"Neural networks (NNs) are utilized in the backstepping approach to design a control input by approximating unknown dynamics of the strict-feedback nonlinear system with event-sampled inputs. The system state vector is assumed to be unknown and an observer is used to estimate the state vector. By using the estimated state vector and backstepping design approach, an event-sampled controller is introduced. As part of the controller design, first, input-to-state-like stability (ISS) for a continuously sampled controller that has been injected with bounded measurement errors is demonstrated and, subsequently, an event-execution control law is derived such that the measurement errors are guaranteed …

Computational Fluid Dynamic Analysis In High Permeability Hydraulic Fractured Horizontal Gas Wells, Hrithu Vasudevan

Masters Theses

"Hydraulic fracturing of horizontal wells in unconventional reservoirs has become the dominant type of well completion performed in the United States. In very low permeability reservoirs (~.00001-.0001 mD), the wellbore is aligned with the minimum horizontal stress, and the completion includes multiple transverse fractures. These fractures may be placed with either open hole sleeve type completion systems (OHMS), or cased hole plug and perf systems (P-n-P). In slightly higher permeability reservoirs (1 to 10 mD) multiple longitudinal fractures have been found to be preferred to completions with transverse fractures.

This study presents an evaluation of gas well productivity for both …

Hydrodynamic Of A Co-Current Gas Liquid Upflow In A Moving Packed Bed Reactor With Porous Catalysts, Ali Jabbar Toukan

Masters Theses

"In this study, the hydrodynamic, i.e. flow regime identification, line average liquid holdup, and the internal liquid holdup of a co-current moving packed bed reactor were studied. For the sake of hydrodynamics study, moving bed reactor is investigated as two-phase upflow packed bed reactor. Scaled down configuration was used to simulate of the moving bed reactors utilized in the industrial process. First, line average liquid holdup is measured with different geometrical configurations covering empty, dry, wet, and packed column under flowrates operation conditions. A new methodology has been developed to determine the line average liquid holdup for a porous catalyst. …

Development And Testing Of A Fracture Energy-Based Model Of Explosive Asteroid Deflection, James A. Veerkamp

Masters Theses

"While asteroid deflection has been studied for the past half century, efforts have generally been directed towards methods that attempt to minimize disruption of the rock body. In order to widen the base of research, a fracture energy-based model of asteroid fragmentation was developed and applied to both asteroid scale and lab testable scale cases. Modeling of the orbital case suggests the capability to deflect a 100 meter diameter asteroid on a 10 year timescale. The model's predicted energy transfer is then compared to laboratory testing using a ballistic pendulum. The results of this testing suggest that the model as …

Data Analysis For Driving Pattern Identification And Driver's Behavior Modeling In A Freeway Work Zone, Hari Narayanan Vijaya Raghavan Nadathur

Masters Theses

"A variety of methods are used by Departments of Transportation (DOT) for informing drivers about upcoming work zones. One such method is work zone signage configuration. Signage plays an important role in work zones to provide guidance to drivers when conditions on the road vary from normal. Therefore, it is necessary to evaluate the effectiveness of different configurations, by law, before implementation of new signage designs that deviate from the national standards.

The Manual on Uniform Traffic Control Devices (MUTCD) is a compilation of national standards for all traffic control devices, including road markings, highway signs, and traffic signals. In …

Correlation Anaylsis Of Magnesite Dissolution Rate And Magnesite Spatial Distribution, Yao Wang

Masters Theses

"This thesis presents a correlation analysis of the spatial distribution and permeability of magnesite dissolution and focuses on its overall rate and average porosity. Magnesite dissolution is affected by several aspects.

A reservoir's large spatial distribution can make capturing the magnesite dissolution difficult, so in this study, a variogram was built in Petrel using a percentage variation of magnesite and sand. The variogram also handles different major and minor directions in anisotropy. After building the magnesite model, simulation of magnesite dissolution was achieved in Cruch Flow to get the magnesite dissolution rate and average porosity.

For correlation analysis, a regression …

Design Of An Adaptive Force And Stiffness Controlled Compliant Device For Robotic Polishing, Mohammad Masud Parvez

Masters Theses

"Polishing is a repetitive task done in an unhealthy environment. Often more than half of the manufacturing time is required to polish a die. The manual polishing process is a tedious work actively rely on a skilled human worker. Industrial Robot has replaced the human in performing these tasks. For robotic polishing to control the polishing force, an active compliant device is used. Due to the compressibility of air, a pneumatic system is preferred as the actuator of the device. The force of the actuator is controlled by regulating air pressure in both chambers of the cylinder. However, to improve …

Reduction Of Emi Due To Common Mode Current Using Common Mode Filter Or Lossy Material, Qian Liu

Masters Theses

"This thesis consists of four papers. In the first paper, two new common mode filter structures were designed, fabricated, and measured. A "sandwich-type" EBG structure that resonates at the desired filter frequency is designed to suppress common mode filter on differential signals. The new filters are placed on top of the PCB as a surface-mount component, instead of being implemented within the PCB stackup. The total radiated power (TRP) of the implemented filter is investigated and discussed. RF absorbing material and traditional shielding are considered to reduce the TRP.

In the second paper and third paper, new PCB-embedded common mode …

Pim Source Identification Using Vibration Modulation Method, Sen Yang

Masters Theses

“In Section 1, passive intermodulation (PIM) is introduced and the mechanism of it is briefly explained. Then, the up-to-date PIM testing and source identification method in the industrial and academia worlds will be summarized.

The vibration modulation method for PIM source identification is proposed in Section 2. Different vibration sources were tested and compared, and the test results showed that the vibration modulation method is able to identify PIM source with good accuracy.

Section 3 outlines a special PIM source identification system built based on the vibration modulation system. The two subsystems, PIM receiver and PIM vibrator, are illustrated in …

Design And Fabrication Of A System For The Additive Manufacturing Of Transparent Glass, Luke John Gilbert

Masters Theses

"Despite glass' prevalence in the scientific and engineering community, very little research has been conducted attempting to additively manufacture (AM) glass. Even less research has been done on optically transparent glass. Glass’ material properties make it ineligible for most AM processes if the end result is to be transparent. Even small gas inclusions can cause large amounts of scattering. Additively manufacturing transparent glass brings the advantages found in other AM processes with the added benefit of having optical properties better than those found in polymers. Additively manufacturing glass also allows the optical properties of transparent parts to vary arbitrarily. This …

Multifunctional Wearable Epidermal Device For Physiological Signal Monitoring In Sleep Study, J V M S Avinash Kankipati

Masters Theses

"Sleep is the essential part of life. Thousands of people are suffering from different kinds sleep disorders. Clinical diagnosing and treating for such disorders are costly, painful and quite sluggish. To reach the demand many commercial products are into the market to encourage home based sleep studies using portable devices. These portable devices are limited in use, cannot be handled easily and quite costly. Advancements in technology miniaturized these portable devices to wearable devices to make them convenient and economical. Elastic, soft and thin silicon membrane with physical properties well matched with that of the epidermis provides conformal and robust …

The Evaluation Of Sequential Optimization And Reliability Analysis, Guannan Liu

Masters Theses

"Sequential Optimization and Reliability Assessment (SORA) has been used for more than one decade for reliability-based design (RBD), but comprehensive theoretical studies on its performance have not been conducted. Further investigations on its performance are still needed. The objective of this thesis is to evaluate the performance of SORA for various testing problems. The performance of SORA evaluated in this thesis includes (1) accuracy, (2) efficiency, and (3) convergence behavior or robustness with numerical testing problems. SORA is evaluated with comparison with other major RBD methodologies. The testing problems are in different scales (numbers of design variables, random variables, and …

Laser Sintering And Aerosol Printing Of Conductive Nanoparticles, Mahati Guntupalli

Masters Theses

"Fabrication and printing of nanoparticles is an essential step in the manufacturing of low cost- high efficiency electronic devices. High material costs of noble metal particles necessitates the investigation for a potential substituent. Conventional methods of manufacturing are time consuming and uneconomical, thus intense research is being done to employ new methods for cost, time and space effective manufacturing process.

The first part of the thesis presents the fabrication of Copper nanoparticles. As an economical substituent for noble metal nanoparticles, Copper nanoparticles satisfy various properties as conductive inks, simultaneously suffering from the vital problem of oxidation. The acceleration effects of …

Synthesis And Photonic Sintering Of Bioresorbable Zinc Nanoparticle Ink For Transient Electronics Manufacturing, Bikram K. Mahajan

Masters Theses

"Zinc is an essential 'trace element' that supports immune systems, and is required for DNA synthesis, cell division, and protein synthesis. Zinc nanoparticles (Zn NP) has antibacterial properties and potential to be used in biodegradable printed electronics devices. The research presented here is about the synthesis of Zn NP and their potential use in transient electronics devices. In Paper 1, a technique of room temperature synthesis of Zn NP is reported using ball milling. Controlled amount of PVP was mixed in the solvent to stabilize the Zn particles and minimize cold welding during milling. The size of the produced Zn …

Mitigation Of Glass Weave Skew Using A Combination Of Low Dk Spread Glass, Multi-Ply Dielectric And Routing Direction, Kartheek Nalla

Masters Theses

"As the data rates increase into the multi-gigabit range, the bit periods fall in the range of few tens of picoseconds. At above few Gbps, it becomes very important to reduce skew between differential pairs as it can adversely impact the signal eye and thereby increase bit error rate. The goal of this study is to mitigate the skew contributed by woven glass fabric of PCB dielectrics.

The glass weave skew between differential pairs in a PCB occurs due to the difference in dielectric constants (DK) of glass and resin. This thesis aims to mitigate the skew by reducing the …

Shear Behavior Of Reinforced Fly Ash-Based Geopolymer Concrete, Noor S. Yacob

Masters Theses

"The geopolymerisation of aluminosilicate materials such as fly ash has been a radical change in construction material's chemistry and composition, compared to the portland cement-based concrete calcium silicate-hydrate chemistry. The adoption of fly ash in concrete industry is a good use of by-product ashes to reduce emissions of the greenhouse gas implicitly. However, in this research, the replacement of portland cement by fly ash is 100%, which makes it a zero-cement concrete with no proprietary chemical additives.

Geopolymer concrete (GC) is a revolutionary synthetic material that combines sustainability and high engineering properties, and it is relatively cost-effective compared to portland …

Biodegradable Electronic And Optical Devices Toward Temporary Implants, Md Shihab Adnan

Masters Theses

"Implantable biomedical devices have a high potential to revolutionize health care technologies in near future. Implantable devices can be classified as permanent prosthetic devices such as pacemakers or nerve stimulants and temporary devices for intermediate monitoring and control scenario which are still in research phase. In contrast to permanent device, temporary implants lose functionality and become unnecessary after intended operational lifetime which may pose serious electromagnetic and biomedical safety concern, latent complications at the implanted sites and possible ethical issues if not removed from body by an additional surgical operation.

The first paper of this thesis focuses on exploring the …

Development Of Learning Objectives For An Undergraduate Computer-Aided Drafting And Design Animation Using The Delphi Technique, Gavin M. Wilk

Masters Theses

This study reflects on learning objectives created for an advanced computer aided drafting (CAD) learning module(s) or course with the emphasis on simulation and engineering animations. These objectives were derived by using the Delphi technique by access the support of a panel of subject matter experts (SME) from academia and industry that are interested in CAD. The results of this study are intended for the use of creating instructional modules for undergraduate studies.

A panel of experts were chosen through an electronic listserv of engineering and technology supporters. Two rounds of two different Delphi survey instruments were utilized to complete …

Simulation Of Lateral Migration And Sedimentation Of A Flexible Fiber In A Vertical Weak Shear Flow, Ali Ibrahim Neamah Neamah

Masters Theses

This research is a thorough numerical investigation and critical analysis of lateral migration of a deformable particle settling in a vertical weak shear flow. Under the vertical weak shear fluid, the deformable particle may move either to the coagulation area, or the dispersion area, depending on Reynolds numbers, shear Reynolds number, fiber flexibility, and aspect ratio. In this study, a lattice Boltzmann equation is used to solve Navier-Stokes equation and a flexible particle method is employed to attack the problem of motion of a flexible fiber. A bounce-back rule is used to deal with moving boundaries interacting with fluids. Several …

Design Of A New Digital Relay For Transmission Line Fault Detection, Classification And Localization Based On A New Composite Relay And Artificial Neural Network Approach, Ahmed Sabri Altaie

Masters Theses

This thesis focuses on new approach to detect, classify, and localize the fault in transmission line. Firstly, fault detection was carried out using the New Composite Relay (CR) which, has different characteristics and the ability to detect any type of fault including series faults. Secondly, fault classification was conducted using the Feed Forward Artificial Neural Network (FFANN). In addition, the fault classification led to the investigation of the best use of the FFANN. The data used come from MATLAB/SIMULINK three phase series compensated network. The results obtained using FFANN, were compared with the type of the fault that have been …

Signage Recognition Based Wayfinding System For The Visually Impaired, Abdullah Khalid Ahmed

Masters Theses

Persons of visual impairment make up a growing segment of modern society. To cater to the special needs of these individuals, society ought to consider the design of special constructs to enable them to fulfill their daily necessities. This research proposes a new method for text extraction from indoor signage that will help persons of visual impairment maneuver in unfamiliar indoor environments, thus enhancing their independence and quality of life.

In this thesis, images are acquired through a video camera mounted on glasses of the walking person. Frames are then extracted and used in an integrated framework that applies Maximally …

A High Performance Architecture For An Exact Match Short-Read Aligner Using Burrows-Wheeler Aligner On Fpgas, Dana Abdul Qader

Masters Theses

Due to modern DNA sequencing technologies vast amount of short DNA sequences known as short-reads is generated. Biologists need to be able to align the short-reads to a reference genome to be able to make scientific use of the data. Fast and accurate short-read aligner programs are needed to keep up with the pace at which this data is generated. Field Programmable Gate Arrays have been widely used to accelerate many data-intensive bioinformatics applications.

Burrows-Wheeler Transform has been used in the theory of string matching which has led to the development of many short-read alignment programs. This thesis presents a …

Formulation And Evaluation Of Soy Polymer Based, Gravure Printed Resistive Inks For Applications In Printed Electronics, Bhushan Hiralal Patil

Masters Theses

Today, the majority of the commercially available conductive inks are formulated using expensive metallic particles, such as silver and gold. Most of the inks use volatile solvents in the formulation, which are hazardous to the environment as emission of VOCs is the major concern. In the case of water-based inks, usually petroleum-based acrylic polymers are used. Apart from being nonrenewable raw materials, acrylic polymers are carcinogenic in nature. Also, acrylic polymers are used in a variety of applications, such as the automotive, medical device, paint, and adhesive industries. Often times, the ink industry has to compete with other industries for …

Design Of Digital Down Converter Chain For Software Defined Radio Systems On Fpga, Nagarjun Marappa

Masters Theses

Modern communication systems have increasingly attempted to trade off the digital signal processing for analog circuitry. In performing this tradeoff, advanced algorithms have been implemented in both custom programmable hardware and in software; such systems are commonly called Software Defined Radios (SDR). Advanced software defined radios consist of highly configurable hardware and computers used as digital signal processing (DSP) platforms that provide the technology for realizing current and future generations of digital wireless communication infrastructure. Many sophisticated signal processing tasks are performed in SDR, including compression algorithms, channel estimation, equalization, forward error correction and protocol management. This research has focused …

Control Of Cation Ordering In Zinc Tin Nitride And In-Situ Monitoring Of Growth, Brian Christopher Durant

Masters Theses

Semiconducting materials with a band gap around 1.5 eV are very much sought after due to their close match to the solar spectrum. However, some compounds that have shown promise for highly efficient solar cells contain rare, expensive, and sometimes toxic elements, such as indium and gallium. As such, a search for earth abundant materials has become more prominent recently. One such earth abundant semiconducting material that has garnered interest is ZnSnN₂. It has been shown through previous studies that there is the possibility of continuously tuning the band gap between 1.0 and 2.0 eV by controlling the …

Morphology Based Framework For Improved Driver's Visibility In Inclement Weather Conditions, Saleem Farhood Hussein

Masters Theses

The U.S. Department of Transportation reports that on average there are 5,870,000 vehicle accidents each year. Twenty-three percent (23%) of these accidents are attributed to weather conditions with an annual average of more than 6,000 people are killed and 480,000 people are injured. Weather-related accidents occur mainly because of the low visibility on the roads under inclement conditions such as snow, rain and fog. While these conditions can be predictable and individuals try to avoid driving in inclement weather, there are circumstances that require driving in such conditions such as emergency responders or when the severity of the storm has …

Computer Aided Brain Tumor Edge Extraction Using Morphological Operations, Warqaa Shaher Alazawee

Masters Theses

Detecting the precise boundary of the area containing a recognized brain tumor is a complex problem and must be addressed since it applies to many medical modalities and tumor types. The objective of this thesis is to provide an efficient algorithm for detecting edges of brain tumors to help neurosurgeons identify the border of the critical area and distinguish the precise margin of the tumor from the rest of the brain tissue during the surgery. This thesis work exploits MRI brain tumor images as a tool to aid surgeons. MRI image segmentation is an essential step as a preliminary process …

Implementing A Linear Quadratic Spacecraft Attitude Control System, Daniel Kolosa

Masters Theses

This thesis implements a linear quadratic attitude control system for a low-thrust spacecraft. The goal is to maintain spacecraft alignment with a time-varying thrust vector needed for trajectory change maneuvers. A linear quadratic attitude control approach is used to maintain spacecraft pointing throughout flight. This attitude control strategy uses the thrust-acceleration input obtained from a linear quadratic optimal trajectory control model that simulates the trajectory of a spacecraft in orbit maneuvers. This attitude model simulates a CubeSat, a small satellite that is equipped with a low-thrust propulsion and attitude control system. An orbit raising and a plane change scenario is …

An Integrated Framework For Cardiac Sounds Diagnosis, Zichun Tong

Masters Theses

The Phonocardiogram (PCG) signal contains valuable information about the cardiac condition and is a useful tool in recognizing dysfunction and heart failure. By analyzing the PCG, early detection and diagnosis of heart diseases can be accomplished since many pathological conditions of the cardiovascular system cause murmurs or abnormal heart sounds. This thesis presents an algorithm to classify normal and abnormal heart sound signals using PCG. The proposed analysis is based on a framework composed of several statistical signal analysis techniques such as wavelet based de-noising, energy-based segmentation, Hilbert-Huang transform based feature extraction, and Support Vector Machine based classification. The MATLAB …