Engineering Commons^™

Projectile Impact Effects On A 50 Psi Plug Type Coal Mine Seal, Bruce Albert Von Niederhäusern

Masters Theses

"The current lack of projectile damage criteria for mine seals is assessed to determine if criteria should be developed. Impact experiments were performed on a full-scale 50 psi mine seal to determine failure modes, dynamic stress state, and assess risk to existing operational mine seals. Test projectiles were selected from common underground coal mine items propelled by means of a black powder projectile generator. Projectile velocities attained in testing ranged from approximately 100 to 650 ft/s (30 to 200 m/s). Dynamic strain was measured on the non-impact face to derive the state of stress and estimate failure criteria. Penetration models …

Multiphysics Prediction Model Of Microwave Curing For Thick Polymer Composites, Siva Dasari

Masters Theses

"Microwave curing technologies have many advantages over the traditional thermal curing methods for the manufacturing of fiber reinforced polymers, especially the processing speed and energy efficiency. Energy can be instantaneously transferred through applied electromagnetic fields and heat is generated based on dipolar rotational interactions. Microwave curing processes have been used for glass fiber composites but there are significant challenges associated with microwave curing of carbon fiber composites. Efficient heating may be difficult due to high dielectric loss associated with carbon fibers. Laminate quality will be highly dependent on the uniformity of the electromagnetic field in the material. In this work, …

Performance Evaluation Of Bmi Resin System For Thin-Ply Composites, Manoj Kumar Reddy Rangapuram

Masters Theses

"Composites materials are increasingly being used in aerospace applications over the past few years. The unique properties like high strength to weight ratio, thermal stability, fatigue and corrosion resistance set them apart from the conventional materials. Composite materials are well suited for the applications where weight is the primary concern in the design. Composites structures are vulnerable to mechanical as well as thermal loadings. Transverse micro-cracking and delamination are the most common type of failures in composite materials. The thickness of the ply being used play a key role dictating the properties of the resultant composite structure. As the ply …

Abrasion Resistant Concrete Mix Design For Cold Climates, Diane Mariah Murph

Masters Theses

“Studded tire usage in Alaska contributes to rutting damage on pavements resulting in high maintenance costs and safety issues. In this study, binary, ternary, and quaternary highly-abrasion resistant concrete mix designs using supplementary cementitious materials (SCMs) were developed. The properties of fresh concrete and mechanical, and durability properties of hardened concrete for these mix designs were then tested to determine an optimum highly-abrasion resistant concrete mixture which could be placed in cold climates to reduce rutting damage. SCMs used included silica fume, ground granulated blast furnace slag, and type F fly ash. Tests including workability, air content, drying shrinkage, compressive …

Methane Dry Reforming Reaction On Cr, V, In, And Ga Supported Sapo-34 Zeolite, Ehigiator Festus Ojo

Masters Theses

”The CO₂ reforming of methane is a significant research area in mitigating and transforming two greenhouse gases for the production of syngas. The reaction has been investigated for four different promoted catalysts to determine their reactant's conversion, product’s selectivity, and their respective syngas ratios.

The catalytic test was investigated under atmospheric conditions at 600⁰C for 6.5h with a WHSV of 4800 ml g^-1 h^-1. The conversion and selectivity of catalysts 9Al 1V-inc SAPO-34, 9Al 1Cr-inc SAPO-34, 9Al 1Ga-inc SAPO-34, and 9Al 1In-inc SAPO-34 were analyzed. The CH₄ conversion for the different catalysts are, 9Al 1Cr-inc …

Unmanned Aerial And Traversing Vehicle -- A Mobile Platform For Bridge Inspections, Clayton A. Fritsche

Masters Theses

“Unmanned aerial vehicles (UAVs), also known as drones, have been rapidly growing in popularity since their creation. This study aimed to create a robotic platform used to assist in the inspection process of the nation’s aging and deteriorating bridges. To this end, a multimodal inspection robot that utilized both flying and driving technologies, was designed, analyzed, and tested for aerial, traversing, and their transitional operability. The design, herein referred to as the “BridgeBot”, was evaluated both computationally and experimentally. A finite element model of the BridgeBot was established and analyzed under static loading scenarios to help determine stress distributions and …

Development Of Castrip Dual Phase Steel, Brenton Allen Hrebec

Masters Theses

“Thermomechanical processing necessary to produce DP 980 steel using CASTRIP hot band was investigated. The resultant steel has an ultimate tensile strength of 1038 MPa, yield strength of 744 MPa, and total elongation of 8.6%. These mechanical properties were achieved by batch annealing the hot band at 649°C for 48 hours and cold rolling to a 20% reduction. The steel was continuously annealed to simulate a galvanization cycle with an intercritical temperature of 810°C. The possibility of improving the texture of the steel by warm rolling under dynamic strain aging conditions was investigated. Dynamic strain aging in the CASTRIP hot …

Performance Of One-Part And Two-Part Class C Fly Ash-Based Alkali Activated Mortars, Cedric Chani Kashosi

Masters Theses

“Seeking an eco-friendly concrete, researchers have conducted studies to fully replace ordinary Portland cement (OPC) with fly ash (FA) producing alkali-activated concrete (AAC). Results showed better performance of AAC in terms of high early compressive strength, and durability compared to conventional concrete. However, much is still unknown about the behavior of AAC. From the type of materials used, the curing procedure, and long-term strength development of these binders; a thorough investigation is needed in order to fill the existing gap from previous studies and thus make a step forward to the safely use of AAC in the construction industry. The …

Estimating Electromagnetic Emissions From A Site Installation With Multiple Racks Of Server Equipment, Ze Sun

Masters Theses

“There are hundreds, sometimes even thousands, of servers working simultaneously inside a data center. Their radiation can be a problem and cause EMI issues. However, it is not feasible to perform full-wave simulation of these racks because of the large electric size of the model. In this thesis, an algorithm is proposed to predict the emission form rack array. The equivalent dipole source is extracted from EMI measurement data of a single rack and used as the radiation source in the multiple rack model. The coupling between racks cannot be ignored, but through the simulation, it is also found that …

Feasibility Study For Sustainable Controlled Low-Strength Material (Clsm) Incorporating Off-Specification Fly Ash And Bottom Ash, Alexis K. Vandomelen

Masters Theses

“Controlled low-strength material (CLSM) is a self-consolidating cementitious material used in applications requiring high flowability and low strength. The primary components of this material, being cement and sand, however, negatively impact the environment. Cement is a large contributor to CO2 emissions, and the vast depletion of sand causes physical and political issues. Furthermore, over 100 million short tons of coal combustion products (CCP), including fly ash and bottom ash, are created annually in the United States, while nearly half of all CCP remain unused. No off-specification fly ash has been implemented in CLSM. This study uses coal ashes sourced from …

Influence Of Pumping Parameters On The Freeze-Thaw And Scaling Resistance Of Highly Workable Concrete, Alexandra Nicole Wehar

Masters Theses

“Over the past 60 years, pumping concrete has gained popularity due to the economic and technical benefits that typically accompanies it. However, boom configuration and flow rate can adversely affect freeze-thaw and scaling resistance of concrete due to the effects of pressure on the air-void system. Therefore, the objective of this research is to assess the influence of different pumping parameters on the durability of hardened self-consolidating concrete. Self-consolidating, flowable, and conventional concrete mixtures were tested during large scale pumping experiments positioning the pump boom in an “A” and a flat shape as well as using different pumping speeds. In …

Laser Machining Countersinks In Carbon Fiber Reinforced Polymer, Leon James Neely Hill

Masters Theses

“Laser machining countersinks with a frequency doubled Q-switched diode pumped Nd:YAG laser is demonstrated. Tests were conducted in 0.100" thick IM7 prepreg CFRP with [0,90]3S orientation. The HAZ is minimized to avoid stress concentrations in the epoxy matrix. A chamber and filtration system was designed and built to contain the byproducts produced in the machining process. The variables investigated are the number of repetitions in the offset path, the plunge rate, and the line energy. The research was performed over one baseline study, one parameter space exercise, two full factorial experiments, and one repeatability study. Assessment was done under an …

Controlled Switching In Kalman Filtering And Iterative Learning Controls, He Li

Masters Theses

“Switching is not an uncommon phenomenon in practical systems and processes, for examples, power switches opening and closing, transmissions lifting from low gear to high gear, and air planes crossing different layers in air. Switching can be a disaster to a system since frequent switching between two asymptotically stable subsystems may result in unstable dynamics. On the contrary, switching can be a benefit to a system since controlled switching is sometimes imposed by the designers to achieve desired performance. This encourages the study of system dynamics and performance when undesired switching occurs or controlled switching is imposed. In this research, …

Inclusion Engineering In Femnal Steels, Rairu Vaz Penna

Masters Theses

"Low density high Mn and Al steels, or FeMnAl steels, show great promise for military vehicles and automotive applications in which high strength and toughness is a requirement. However, these steels are subject to processing challenges including development of oxide and nitride inclusions during melting and casting as well as a large as-cast grain size and heavy interdendritic segregation. This can lead to non-uniform heat treatment response and cracking during subsequent hot rolling. Adding up to 10%Al lowers the density of these steels by as much as 15%, unfortunately, this also results in large amounts of hard and faceted AlN …

Modeling Of Optimized Neuro-Fuzzy Logic Based Active Vibration Control Method For Automotive Suspension, Mohammad Adom Safiullah

Masters Theses

In this thesis, an active vibration control system was developed. The control system was developed and tested using a quarter car model of an adaptive suspension system. For active vibration control, an actuator was implemented in addition to the commonly used passive spring damper system. Due to nature of unpredictability of force required two different fuzzy inference system (FIS) were developed for the actuator. First a sequential fuzzy set was built, that resulted lower vertical displacement compared to basic damper spring model, but system had limited effect with disturbances of higher magnitude and continuous vibrations (rough road). To improve the …

Vhf Transmitter Development For Wildlife Tracking, Bryan Westra

Masters Theses

Wildlife biologists often use collars with VHF transmitters to gather wildlife data. The purpose of this project is to determine the best approach to designing a wildlife tracking VHF transmitter on a Printed Circuit Board (PCB). A variety of frequency generation methods were considered for the transmitter, including transistor-based crystal oscillators and chip based solutions from the chip manufacturers Analog Devices and Silicon Labs. Prototypes of the feasible options were built and evaluated for cost, power consumption, efficiency, size, frequency range, signal bandwidth, and frequency stability. It was found that the Silicon Labs Si4010 chip was the best solution based …

Power Optimization Of Solar Powered Standalone Wireless Sensor System, Rajan Amatya

Masters Theses

Wireless sensor systems are common in applications where harsh environmental conditions or remote locations make it difficult to run wires. Having these sensor systems self-powered is essential as it is difficult for battery replacement. Using solar as an alternative source of energy can be a medium to charge the battery in such scenarios. With an increasing number of portable devices powered by battery; more and more research is focused on low-power design technique. For this thesis, a microcontroller (Texas Instruments MSP432) was used along with a digital sensor (Bosch BME280) to provide temperature, pressure and humidity information, and Wi-Fi module …

Soy- Based Flexographic Ink For Linerboard Printing, Rahul Ramchandra Pingale

Masters Theses

Many printing inks use volatile solvents in the formulation, which are hazardous to the environment from emission of VOC’s and at the same time, synthetic resins in these inks are not biodegradable. These problems with the fluctuating and rising price of petroleum are main reasons to look for new resources for making more environmentally friendly printing inks. The majority of the commercially available water based inks are formulated based on using acrylic resins, synthetic colorants, solvents/water and additives, which are the common main components for formulating printing inks. In this research, soy proteins were tested for their suitability to partially …

Optimization Of Analytical Inverse Heat Transfer Recovery Solution, Nathan Schick

Masters Theses

This thesis describes the different methods used when trying to solve inverse heat transfer problems, particularly those involving recovering heat flux. There are currently several techniques to measure the temperature history in an object subjected to heat transfer using various temperature sensors, however these types of sensors are gradually being replaced by Temperature Sensitive Paints (TSP), a technique that is more accurate and provides a better spatial resolution. TSP is a polymer that is applied on a base object. Changes in temperature in the polymer result in variations of the luminescence intensity in the paint. These variations can be captured …

The Passive Effects Of Full-Gateway, In-Street Signs On Vehicular Speed, De'lon Dixon

Masters Theses

Reducing motorist’s speed when approaching crosswalks is an important goal in reducing the number of collision between motorist and pedestrian in crosswalks. The current study addresses this goal. The effect of gateway installation of in-street signs (one in-street sign installed between the two travel lanes in each direction and one on both edges of the roadway in each direction) on vehicle speed was evaluated on nine roads. The results demonstrated that the Gateway in-street sign treatment produced large speed reductions as vehicles approached the crosswalk and at the crosswalk. The average speed reduction was 3.8 mph at the crosswalk and …

Stereotypic Repetitive Hand Flapping Movement Detector Children With Autism, Subodh Ashok Bansode

Masters Theses

The prevalence of Autism Spectrum Disorder (ASD) has increased at a significant rate in recent years, especially in developed nations such as the United States, Japan, and South Korea. Extensive research is being carried out to study the behavioral characteristics of the disease. Children affected with autism tend to exhibit a spectrum of symptoms depending on the severity of the disease. These behaviors are primarily repetitive, self-stimulatory, and stereotypic behaviors such as hand flapping (i.e., repeatedly shaking their hands), body rocking (i.e., swaying their body back and forth), drumming, walking around in a confined space, and walking with shortened steps …

Evaluation Of Bike Boxes And Protected Intersections With Bicycle Signal Treatments For Improving Safety And Multimodal Mobility At Urban Signalized Intersections, Odai Al Houz

Masters Theses

With the dramatic increase of non-motorized transportation users, more people are concerned about the non-motorized traffic safety. Unfortunately, bicyclist and pedestrian are prone to more severe injuries when involved in a crash. For bicycle crashes, failing to yield/disregarding traffic control device, and lack of non-motorized facilities were identified to be the main causes of bicycle crashes in urban intersections. This research investigated the effectiveness of two bicycle crash countermeasures with bicycle signal treatments at urban signalized intersections. The two countermeasures are the bike boxes and the protected intersections. The bicycle signal treatments are the leading bicycle interval and the exclusive …

Variable Reluctance Virtual Torque Sensor For Automotive Applications, Vivek Iddum

Masters Theses

Torque sensing has been realized as one of the critical aspects in improving the dynamic vehicle performance in automotive systems. This thesis mainly presents the work on the development of a novel torque measurement method based on the estimation of nth-order flywheel angular acceleration from the variable reluctance flywheel speed sensor pulses. The number of firings in the engine determine the order of the harmonic to be used for torque estimation. The nth-order flywheel angular acceleration is computed using a micro-controller with built in timer counter and an associated signal conditioning circuit. The pulses obtained from the flywheel speed sensor …

Design Of A Portable Biogas Purification And Storage System, Anilkumar Kosna

Masters Theses

Biogas is produced from the decomposition of organic materials like manure, sewage sludge or crop fodders in anaerobic digesters. It consists mainly of 40 – 75 % of methane (CH₄), 15 – 60 % of carbon dioxide (CO₂) and trace amounts of other components. The principle constituents of biogas are similar to natural gas. Natural gas has 87 – 97 % of methane (CH₄) and 0.1 – 1 % of carbon dioxide. Natural gas is known to be an alternative fuel with a wide range of applications. The commercial purification technologies exist for large-scale …

Enabling Robust Distributed Real-Time Hybrid Simulation Method And Expanding Its Applications In Floating Wind Turbine Systems, Mehmet Cinar

Masters Theses

Real-time hybrid simulation (RTHS), which integrates physical experiment and numerical simulation, plays an essential role in understanding the time-dependent behavior of structures when subject to hazardous loadings. On the other hand, RTHS might not yield accurate results for complex structural systems due to experimental and computational limitations. Distributed real-time hybrid simulation (dRTHS), which takes the advantage of distributed laboratory facilities using network communications, was proposed and proven to address some limitations in RTHS. During dRTHS, Internet delay due to the network communication is added to the actuator delay in RTHS, which may cause inaccurate results or even unstable tests. To …

Liquid-To-Liquid Low Grade Waste Heat Recovery Using A Two-Channel Loop, Waleed Farwana

Masters Theses

The use of thermoelectric generators (TEGs) for producing electric energy from low grade “waste heat” has been theorized to provide a sustainable and low-cost energy source for electric power plants. The purpose of this study is to model and experimentally validate a TEG device that takes advantage of low grade waste heat (approximately 100-150 degrees Celsius) in liquid form in order to generate power that can be used for various applications in the surrounding environment. This research aims to demonstrate that optimized TEG designs bear the potential to compete with other methods of low grade waste heat energy harvesting in …

Object Detection, Classification, And Tracking For Autonomous Vehicle, Milan Aryal

Masters Theses

The detection and tracking of objects around an autonomous vehicle is essential to operate safely. This paper presents an algorithm to detect, classify, and track objects. All objects are classified as moving or stationary as well as by type (e.g. vehicle, pedestrian, or other). The proposed approach uses state of the art deep-learning network YOLO (You Only Look Once) combined with data from a laser scanner to detect and classify the objects and estimate the position of objects around the car. The Oriented FAST and Rotated BRIEF (ORB) feature descriptor is used to match the same object from one image …

Establishing Delay-Based Criteria For Installing Traffic Signals At Two-Lane Roundabouts, Oluwaseun Ayomide Adegbaju

Masters Theses

A roundabout is a circular intersection where drivers travel counterclockwise around a center island in the United States. Roundabouts can be more beneficial than the conventional intersections because they increase the capacity of the intersection and reduce delays and crashes at the intersection. However, the performance of roundabouts can be severely affected by unbalanced traffic flows among the approaches. While the resulting delays can be mitigated by installing traffic signals, there is a lack of clear criteria on when to install a traffic signal at a roundabout. This research focuses on establishing criteria for installing traffic signals at two-lane roundabouts …

The Design, Analysis, Development, And Test Of A High-Energy Trauma Prevention Safety Device, Samuel B. Schaefer

Masters Theses

The continued development of modern-day vehicles has allowed innovators to shape their design to meet the consumer’s requirements. Vehicles have become faster and larger to accommodate more passengers and their belongings. The increased popularity of Light Trucks or Vans (LTVs) and Sports Utility Vehicles (SUVs) elevated their sales to approximately 50% of all vehicles sold in the United States by 1999 [1]. These advancements have created a high-energy world, which poses a serious threat to the ever-growing population. Unprotected pedestrians come in all too frequent contact with these vehicles creating the potential for high-energy blunt force trauma. This thesis aims …

Design And Testing Of A Sheath Device To Secure Rotator Cuff Anchors In Osteoporotic Bone, Alissa Smith

Masters Theses

A rotator cuff tear is a common injury that affects many elderly people. These tears vary in severity, with moderate to severe tears requiring surgery. In rotator cuff surgery, bone anchors are used to re-attach the supraspinatus tendon to the humerus. This surgery is difficult in many older patients because aging bones become osteoporotic, or soft, and thus inadequate for securing bone anchors. Studies confirm that osteoporotic bone is a contributing factor of implant failure. A finned sheath concept was designed, developed, and tested to ensure securement of the bone anchors during and after rotator cuff repair. The sheath interacts …