Engineering Commons^™

Optimization Of Transit Smart Card Data Publishing Based On Differential Privacy, Chenxi Chen

Masters Theses

“Privacy budget allocation is a key step of the differential privacy (DP)-based privacy-preserving data publishing (PPDP) algorithm development, as it directly impacts the data utility of the released dataset. This research describes the development of an optimal privacy budget allocation algorithm for transit smart card data publishing, with the goal of publishing non-interactive sanitized trajectory data under a differential privacy definition. To this end, after storing the smart card trajectory data with a prefix tree structure, a query probability model is built to quantitatively measure the probability of a trajectory location pair being queried. Next, privacy budget is calculated for …

Method Of Optimal Battery Scheduling With Optimal Battery And Photovoltaic Sizing, Gideon Hallman

Masters Theses

“Renewable energy generation is on the rise. One of the best ways to capitalize on this intermittent power supply is by using the renewable energy source in tandem with batteries. A joint photovoltaic (PV) and battery system model was created that implemented battery degradation and optimized battery usage using a Markov Decision Process (MDP). This system was then subjected to a series of tests to do a sensitivity analysis while optimizing the battery and PV sizing for the system at hand. Parametric sweeps of solar power and battery capital costs, the cost of energy taken from the grid, the cost …

The Role Of Psychological Reactance In Smart Home Energy Management Systems, Matthew Thomas Heatherly

Masters Theses

“With an ever-growing demand for energy, our increasing consumption is producing more greenhouse gases and other pollutants, impacting climate change. One approach to reducing residential energy consumption is through the use of smart energy management systems. However, automation from smart technology inherently removes a certain amount of control from the user. If loss of control is perceived as a loss of freedom, this may lead users to experience psychological reactance when using these products. A set of experiments was conducted to assess how three features of a message notification from smart home energy management systems may induce reactance in users. …

A Physics-Based Pi Pre-Layout Tool For Pcb Pdn Design, Shuang Liang

Masters Theses

"With increasingly stringent requirements for lower voltage supply, and higher density in PCB PDN design, now integrity (PI) is an increasingly important aspect that must be considered. A pre-layout tool based on the Cavity Model and Boundary Element Method is built to automatically achieve a specified target impedance for a multi-layered Printed Circuit Board (PCB) Power Distribution Network (PDN) design with a minimal number of decoupling capacitors.

The pre-work about the post-layout design and analysis is proposed and the guidelines for creating a decoupling capacitors network with better performance has been built. With limit inputs, physical limitations for the minimal …

Development Of Complex Lattice Cell In Benchmark Model Of Particle Bed Critical System, Elijah Chamberlain Lutz

Masters Theses

“Criticality safety benchmark evaluations require the creation of models that most accurately represent the experiment being evaluated. In some cases this can be relatively trivial with experiments containing rather simple or standard geometry. In others, such as packed bed systems, this becomes unique and a more difficult process. The importance of accurate modeling of packed bed systems for the use of criticality safety benchmark evaluations was looked at. Four models were created of various complexities and accuracy. First the multi-particle bed, consisting of a fuel particle (UC_1.7 kernel with C shell) and two filler particles (Zircaloy-4 and C + …

Design And Evaluation Of The 3d Printed Electromagnetic Absorber Built With Conductive Carbon-Filled Filament, Rui Mi

Masters Theses

"This research presents an application of the resistive frequency selective surface (FSS) fabricated with a 3D printed conductive material as an electromagnetic absorber for the EMI-reducing door. This solution allows to reduce radiated emissions of a router system. The resistive frequency selective surface has a three-layer structure. The top layer is a 3D printed FSS pattern, the middle layer is an air gap, and the bottom layer is a metal plane.

The first paper presents the methodology for manufacturing a frequency selective surface using the 3D printing technology, including the material characterization, design, fabrication, and evaluation.

The unpublished content presents …

The Effects Of Rigid Polyurethane Foam As A Confinement Material On Breaching Charge Detonations, Nathan Franz Paerschke-O'Brien

Masters Theses

"The effects of a rigid polyurethane foam used as a confinement material on four types of breaching explosives were tested, focusing on the changes in shockwave peak pressures, detonation load compression forces, and brisance cratering abilities. The Plate Dent testing procedure was modified to incorporate a load cell force sensor, and two air overpressure sensors were included adjacent to the blast to quantify each test result. The testing variables focused on the polyurethane foam cure times and thickness volumes around the breaching explosives to determine the breaching charges' optimal energy output capabilities when confined by the foam material. The rigid …

Investigation Of The Sensitivity Of Human Arm To Small Interaction Forces During Physical Human-Robot Interaction (Phri), Fazlur Rashid

Masters Theses

“Understanding the human motor control strategy during physical interaction tasks is crucial for developing future robots for physical human-robot interaction (pHRI). Effective pHRI depends on humans communicating their intentions for movement with robots. In physical human-human interaction (pHHI), small interaction forces are known to convey their intent between the partners. It is speculated that small interaction forces contain significant information to convey the movement intention of pHHI. However, the mechanism underlying this interaction strategy is largely unknown. Hence, the aim of this work was to investigate what affects humans’ sensitivity to the interaction forces. The hypothesis was that small interaction …

Early Wildfire Detection By Air Quality Sensors On Unmanned Aerial Vehicles: Optimization And Feasibility, Doaa Rjoub

Masters Theses

“Millions of acres of forests are destroyed by wildfires every year, causing ecological, environmental, and economical losses. The recent wildfires in Australia and the Western U.S. smothered multiple states with more than fifty million acres charred by the blazes. The warmer and drier climate makes scientists expect increases in the severity and frequency of wildfires and the associated risks in the future. These inescapable crises highlight the urgent need for early detection and prevention of wildfires. This work proposed an energy management framework that integrated unmanned aerial vehicle (UAV) with air quality sensors for early wildfire detection and forest monitoring. …

Transfer Function Measurement For Automotive Intentional Emi And Thermal Runaway Investigation Of Lithium-Ion Battery By Intentional Emi, Woncheol Song

Masters Theses

"With an increasing demand for electric vehicles and autonomous driving, many components of a vehicle are being replaced as electric components. This implicates the possibility of an increase in the malfunction of electric components due to unknown electromagnetic interferences. In this reason, malicious intentional electromagnetic interference (IEMI) is being considered as a growing threat for the current and next generation of automotive technology.

In the first topic, the transfer function between the IEMI attacker and the engine control unit (ECU) circuit in an automobile is extracted to analyze how the IEMI affects the vehicle.

In the second topic, to mimic …

Bond Graph Modeling Of Critical Infrastructures For Cyber-Physical Security Implementation, Michele Jane White

Masters Theses

“In developed societies, there exists infrastructure vital to everyday life. This includes water and power systems. Technology is quickly evolving and being implemented on these utilities. This technology can range from smart metering in neighborhoods to volume sensors in local waste water treatment facilities. When networking, sensing, monitoring, or control devices are integrated with infrastructure it is considered a cyber physical system, or CPS. When information about an important physical system is connected to the virtual world, it is opened up to security risks. Cyber security can be provided to the CPS by monitoring the physical state of the system …

Multiple-Site Fatigue Cracking Methodology To Assess Structural Integrity Of Aircraft Riveted Panels, Haroldo Chacon

Masters Theses

“Multiple Site Damage (MSD) is the most common source of Widespread Fatigue Damage (WFD) affecting structural integrity of aging aircraft fleets. Therefore, an understanding of its progression, the development of methods to prevent the onset, and the maintenance procedures precluding WFD are important to improve aircraft fleet longevity. A reliable and efficient numerical methodology to perform detailed Multiple Site Damage assessment in riveted structural joints was developed. A probabilistic methodology was employed in conjunction with Monte Carlo simulation technique; the fatigue initiation life at every potential crack initiation site was determined and initial damage scenarios were generated. Probabilistic crack growth …

Fabrication Of Silicon Nitride Parts By Ceramic On-Demand Extrusion Process, Sachin Choudhary

Masters Theses

“Ceramic On-Demand Extrusion (CODE) is a patented solid freeform fabrication method for manufacturing high-density monolithic ceramic parts. In the past 5-6 years, the technology has been successfully implemented to fabricate alumina and zirconia parts. The mechanical characterizations also show CODE’s high potential in achieving desired structural properties. The present study covers the fabrication of silicon nitride parts by CODE process, which entailed the design of paste formulation for achieving rheology suitable for dimensional control in fabricated parts and determining firing temperature and the content of sintering additives for silicon nitride green bodies fabricated by CODE. The density, hardness, and fracture …

A Compact Wavelength Meter Using A Multimode Fiber, Ogbole Collins Inalegwu

Masters Theses

“Wavelength meters are very important for precision measurements of both pulses and continuous-wave optical sources. Conventional wavelength meters employ gratings, prisms, interferometers, and other wavelength-sensitive materials in their design. Here, we report a simple and compact wavelength meter based on a section of multimode fiber and a camera. The concept is to correlate the multimodal interference pattern (i.e., speckle pattern) at the end-face of a multimode fiber with the wavelength of the input lightsource. Through a series of experiments, specklegrams from the end face of a multimode fiber as captured by a charge-coupled device (CCD) camera were recorded; the images …

Research And Development Of A Laser Hot Wire Deposition Process, Christopher Croft

Masters Theses

“Laser hot wire directed energy deposition (DED) is an increasingly popular method for improving deposition rates and overall reduction of build times in DED processing. While there is clear benefit, it is important to fully understand the impact of preheating the wire. This work focuses on developing a model that describes bead geometry output using all factors including the wire preheat. The model was fit with over 150 data points that explored a large range of each factor. The resulting model was then leveraged to evaluate a process control variable. The technique chosen used feedback from the hot wire system …

Analysis And Design Of Dc-Link Capacitor In Cascaded H-Bridge Multilevel Active Front-End Converter, Muhammad Shehroz Malik

Masters Theses

Medium-voltage grid-tied systems often use a cascaded H-bridge multi-level active front-end. In this converter, dc link bus capacitors play an important role in stabilizing the converter and enabling both active and reactive power injections. The present work provides analytical expressions for the capacitor current, which are essential for optimizing system design (especially capacitor size vs. lifetime). Then, the expression is incorporated into the grid connected bidirectional power system model. Consequently, this work contributes to the guiding principles to choose accurate dc link capacitor ratings against grid-side power delivery requirements.

DC-link capacitors come with an expiration date which is dependent on …

Effect Of Spike Anchors On The Bond Behavior Of Steel Reinforced Polymer Composite Externally Bonded To A Concrete Substrate, Keenan Lorence Mcburney

Masters Theses

Steel reinforced polymer (SRP) composites are a strengthening material that consist of continuous high-strength steel cords embedded in a polymeric matrix. SRP has demonstrated a high potential for providing additional flexural and shear strength in existing concrete structures when bonded to the concrete surface. However, premature debonding from the concrete substrate at low load levels is a major shortcoming of SRP composites. It has been demonstrated in previous studies that anchors can limit the effect of debonding in fiber reinforced polymer (FRP) composites by increasing the load capacity and ductility of the composite-concrete interface.

This study aims to investigate the …

Physics-Based Modeling Of Lithium-Ion Batteries For Control And Estimation Applications, Brody J. C. Riemann

Masters Theses

“Lithium-ion batteries are extensively used in many application areas like consumer electronics, electric vehicles, and microgrids. As the world moves towards further electrification of vehicles and more widespread use of renewable energy sources, the need for large-scale battery storage systems will grow. To effectively replace conventional methods, batteries will need to be charged quickly while accounting for degradation to maximize lifetime. Further, larger batteries require more detailed safety monitoring, which is implemented using a battery management system (BMS). A BMS is responsible for state of charge (SOC) estimation, state of health (SOH) estimation, cell balancing, regulating voltage and current according …

Seed Modeling Of An Esd Gun Discharge To A Usb Cable, Yang Xu

Masters Theses

“An IC protected by a transient voltage suppression (TVS) diode may fail if the TVS device does not turn on or does not turn on quickly enough, causing the IC to take the full brunt of the electrostatic discharge (ESD) event. Transient simulation models have been developed for ESD protection devices for the purpose of system-efficient ESD design (SEED). The TVS modeling methodology has been improved to better represent the physics that occurs during the TVS response and more accurately predict the interactions between off-chip and on-chip protection devices. Moreover, a complicated test scenario -- an ESD gun discharge through …

Topological Biclustering Artmap, Raghu Yelugam

Masters Theses

”Detection of gene mutations is central for assessing genetic factors affecting disease predisposition, genetic causes of a particular disease, and gene-targeted treatment. DNA microarray methods are widely used to detect mutations by contrasting the expression levels of thousands of genes together under varying experimental conditions. The experimental conditions could be diseased cell states compared with the normal cell states. Biclustering, a robust exploratory data analysis tool, can be applied to microarray data to detect subsets of genes that co-express highly only for a subset of experimental conditions. Such detection is crucial for gaining insights into gene regulatory networks, differential gene …

Axial Performance Of Self-Consolidating Concrete-Filled Fiber Tubes, Joshua David Carter

Masters Theses

"Concrete filled fiber tubes can be used to increase ductility and strength of a concrete member and self-consolidating concrete is an ideal material to use in practical applications of concrete-filled fiber tubular columns. However, the propensity of self-consolidating concrete to autogenous shrinkage could reduce the effectiveness of the concrete confinement. This research investigates the use of self-consolidating concrete in pre-cast FRP tubes and various methods of shrinkage reduction and compensation to increase the axial performance of said self-consolidating concrete-filled fiber tubes. Axial compression tests were performed under monotonic and cyclic conditions to determine the stress-strain relationship of the self-consolidating concrete …

Composite-Based Additive Manufacturing Applications In The Polymer Injection Molding Cycle, Cody Bivens

Masters Theses

“The experimental method utilized in this research was the application of composite-based additive manufacturing (CBAM) mold plates in the injection molding process. The mold plates comprised carbon fibers and polyether ether ketone (PEEK) matrix. Modifications were made to the mold plates post manufacturing in order to properly adapt to the rest of the injection molding die. A custom cooling system was engineered and integrated into the injection molding machine for the CBAM mold plates. The polymer processed in the injection molding cycle for this study was Lustran 348 acrylonitrile butadiene styrene (ABS). The result of the trials conducted in this …

Atherosclerosis: Pathology, Role Of Sd-Ldl, Particle Size Characterization Of Sd-Ldl With Multiangle Light Scattering, Akshay Sudhakar Ukey

Masters Theses

Atherosclerosis is an inflammatory disease due to the accumulation of lipids in the inner wall of arteries. As per the report of Center of Diseases Control and Prevention (CDC), 1 in every 4 deaths is due to heart diseases each year. Atherosclerosis occurs when artery walls harden by the buildup of cholesterol, forming multiple atherosclerotic plaques within the aorta (4). Out of the modern medicines available to control cholesterol, statin is amongst the foremost widely used because it is both safe and effective in lowering high risk patients (9). However, usage of high statins dosage typically leads to some mild …

Development Of A Single Emitter Ionic Liquid Ion Source Research Platform, Thomas V. Kerber

Masters Theses

A single emitter ionic liquid ion source using porous borosilicate glass was developed. Two emitters with different radii of curvatures were tested using 1-ethyl-3-methylimidazolium tetrafluoroborate (EMI-BF₄). I-V curves of the currents on the extractor electrode and a collector plate were obtained for potential differences between the emitter and the extractor ranging from 0 V to 3500 V. For the first emitter chip, extraction began near 2400 V. The highest emission current measured on the first chip was 80 µA at 3500 V with an interception current on the extractor of 4.86 µA. An new collector plate was used …

Synthesis And Characterization Of Non-Pgm Catalysts For Fuel Cell Applications, Sudharsan Sridhar

Masters Theses

Fuel Cells convert the chemical energy of a fuel and an oxidizing agent into electricity through a pair of redox reactions. Proton Exchange Membrane (PEM) fuel cells convert (efficiency-60%) hydrogen and air to power the electric motors with zero emissions, facilitating the development of environmentally friendly and sustainable automobile technologies. One of the major obstacles for larger commercial viability of Fuel Cells for automobile applications is their cost-effectiveness. Currently, fuel cells use platinum as a catalyst material, which is prohibitively expensive for commercial automobile applications. The development of non-Platinum Group Metal (non-PGM) catalyst materials with similar electrochemical performance to that …

Cellular Attachment On Poly(Lactic Acid) For Use In Tissue Engineering, Stephen R. Hunter

Masters Theses

Tissue engineering is a promising new method for organ regeneration. This method can be used to repair damaged tissue, or possibly replace a fully functional organ. In summary, a biopsy is taken from a donor, isolated, then grown onto a framework resembling an organ. Once grown; it is then transplanted into the patient. Over time, the body will degrade the scaffold, leaving the organ or tissue in its place. As this scaffold is present in the body for an extended time; factors like biocompatibility, toxicity, immunogenicity, and structural stability must be researched.

Several polymers have already been researched for use …

Intelligent Roadside Unit Deployment In Vehicular Network, Xiangyu Xu

Masters Theses

Intelligent Transportation System (ITS) has been an important research area in building the foundational infrastructures of self-driving vehicles and improving traffic efficiency of future transportation systems. Scientists have been hoping to incorporate intelligence into traditional transportation systems to help reduce the risks, accident rates, traffic congestion, and even environmental emissions.

There are many research works that have been focused on the communication part of ITS, such as vehicular networks, which collect data from vehicles and send it to the cloud for analysis. In the vehicular networks, Roadside Unit (RSU) is a key infrastructure as an intermediate layer between the vehicles …

A Cfd Study Of Operation Room Air Conditioning: Air Curtain Performance, Spencer Lee Boer

Masters Theses

An operation room is a critical environment when it comes to the safety of patients undergoing surgery. There are a lot of factors that go into reducing Surgical Site Infections (SSI) following a surgery. This comes in the form of cleaning standards, surgical practices, but also environment controls. The characteristics of airflow within an operation room are related to the risk of an SSI. Some of these factors are temperature, velocity, and turbulent air around an open wound which could increase the chance of bacteria or other particles entering the very vulnerable patient. As clean room standards continue to be …

An Investigation Into The Development Of A Low Cost, Easy To Use Seizure Analysis Tool., Cody Dean

Masters Theses

The need for collaborating and sharing data and research between doctors, researchers, universities and patients has never been more necessary. We are seeing firsthand how a deadly virus can completely devastate the world in a matter of months and being able to react quickly is the top priority. Open source tools are making it possible to share research and learnings about viruses like COVID-19 across countries, industries, and universities and these tools and philosophies extend across all areas of medical research.

The amount of data that is being collected within the medical industry is increasing at an exponential rate and …

Development Of A Tiny House Design Tool To Increase Safety, Efficiency, And Cost-Effectiveness, Michael Joseph Stratton Ii

Masters Theses

A growing number of people are choosing to live more sustainably, and this is commonly done through living in an extremely small house, also called a “tiny house”. There is no set definition for a tiny house, but it typically refers to a structure less than 500 ft2, sometimes built by the homeowner, and frequently built on a travel trailer.

The popularity of tiny houses has increased over the years due to different television shows, internet videos, and photo sharing websites, but the technical details are rarely covered, which is why this study examines the structural, stability, weight, and thermal …