Engineering Commons^™

A Study Of Digital Computer Control Of A Continuous Pulp Digester., Charles Edward Barker

Masters Theses

"Detailed analysis of six basic control loops for a Kamyr continuous digester is described using z- and s- transform methods. An example of a digital computer control system for a continuous digester is also presented"-- Abstract, p. ii

The Investigation Of Video Sensitivity And Data Processing Errors Encountered In An Airborne Receiver, James Lee Hamilton

Masters Theses

"The investigation of video sensitivity and both biphase demodulation and Doppler shift processing errors is performed. The effect of pass band ripple on the noise bandwidth of two pole filters is developed. The effect of feedback on the effective noise figure of a high gain IF (Intermediate Frequency) amplifier is investigated and discussed. An analysis of a limiting amplifier-biphase demodulator circuit is attempted. A computer simulation of this same circuit is also performed and the results are compared to measurements taken in the laboratory. With respect to multipath corrupted input signals, a differential phase shift keyed biphase demodulator is shown …

Local Buckling Of Cold-Formed Steel Structural Members Having Initially Curved Compression Elements, William M. Mckinney

Masters Theses

"A comprehensive investigation of the effect of initial deviation from flatness on buckling stress and post-buckling strength of compression elements in structural plate members is presented. The study of stiffened and unstiffened elements expands the scope of elastic stability for initially curved plates. Finite element techniques were utilized for the study of unstiffened elements"--Abstract, page ii.

Combined Forced And Free Convection On A Vertical Cylinder And Flat Plate, Aleksandros Mucoglu

Masters Theses

"In the study of fluid flow over heated surfaces, it is customary to neglect the effects of buoyancy force when the flow is horizontal. However, such a practice is not justified when the forced flow is along an inclined or a vertical surface, because under these conditions the buoyancy force modifies considerably the flow field and hence the heat transfer rate from the surface. Such a flow is termed combined forced and free convective flow.

The present study is concerned with the effects of buoyancy force on forced convection along an isothermal vertical cylinder and a flat plate. This type …

Graph Model Analysis Of Computer Structures, Ömür Taşar

Masters Theses

"Graph theory is applicable to the solving of problems in nearly every field of scientific study. The purpose of this thesis is to consider its applications in representing and analyzing digital computers. Fundamental graph theory definitions, the types and the properties of the directed graphs, the matrix representation, and several reduction techniques are discussed. The blocking gate method for diagnosing computer systems is described and applied to the Scientific Control Corporation (SCC) 650 for its fault-diagnosis.

Microprogramming has been a significant trend in hardware and software designs of computers. Microprogrammed computers are discussed in comparison to conventional computers. A general …

A Planning Study On The Electrical Load Requirement For The New Town Of Pattonsburg, Javad Yousefian

Masters Theses

"Because of an Army Corps of Engineer proposed new dam on the Grand River 1 the original town of Pattonsburg, Missouri was to be inundated by the resulting lake reservoir formed above the dam. The city planners proposed the relocation of the town site adjacent to the new lake, forming a lake side community attractive to both a residential population and for industrial locations.

The electrical power loads of New Pattonsburg's residential, industrial, commercial, and municipal areas, as well as its street lighting power requirements, were planned for a population of 50,000. Statistical analysis of demographic surveys was employed to …

Magnetostrictive Aftereffects In A Dilute 50fe-50ni-C Alloy, Raj N. Master

Masters Theses

"Crystallographically equivalent interstitial sites are energetically equivalent when the host crystal is free of any fields. This situation is shown in Fig. Pl from which it may be appreciated that the difference of the free energy of the "crystal" with an interstitial "I" located in "x" and "y" sites, respectively, is equal to zero. This energy equivalence of the various interstitial sites is destroyed when the host crystal is subjected to fields such as strain fields, magnetization fields or a combination of both as may be appreciated from Figs. P2 through P4. In this case, the interstitials will preferentially occupy …

Flow Field And Heat Transfer For Developing Flow Of Molten Glass In A Duct, Russell Ralph Beckmeyer

Masters Theses

"The molten glass flow (temperature range 1300 to 1500°C) in the entrance region of a duct was investigated with numerical methods. The mathematical model was restricted by assuming: (1) two dimensional, steady state, (2) Newtonian fluid, variable viscosity, and (3) Rosseland approximation. In addition, appropriate use was made of the fact that the Reynolds number is small and the Eckert number is very small. The inclusion of temperature dependent viscosity and a Rosseland approximation for radiation produced from the mass, momentum, and energy equations a system of coupled, nonlinear, partial differential equations which were solved by an iterative finite difference …

Computer Analysis Of 3-Phase Induction Motor Operation On An Open-Delta Distribution System, S. Clark Seematter

Masters Theses

"Open-delta/open-delta and open-wye/open-delta transformer banks are often used as an economic means of supplying simultaneous single-phase and 3-phase loads. If the 3-phase load is an induction motor and if these banks are used, the inherent voltage unbalance causes increased losses and uneven heating that may lead to motor failure. Two previously published theories are used to predict motor heating that is caused by the unbalanced voltages and the motor derating that is necessary to prevent insulation failure"--Abstract, page ii.

Investigation Of The Electric Field In The Vicinity Of A Water Drop Adhering To A Conductor, Jamnarn Hokierti

Masters Theses

"Electric field calculations in the vicinity of a conductor above ground are developed with constraints on the distance from the conductor for which the electric field equations can be applied for practical applications. The electric field in the vicinity of a small water drop adhering to the conductor has been calculated. Application of this electric field in the vicinity of the water drop has been used to compute the apparent surface charges and also the forces on the small water drop surface. Methods for the calculation of space charge due to ionization on the water drop has been suggested"--Abstract, page …

Distribution Of Ambient Particulates And Particulate Trace Metals Around The Amax Smelter, Pramod Maneklal Shah

Masters Theses

"The purpose of this investigation was to study the distribution of metallic particulates in the air surrounding the AMAX Lead Company of Missouri smelter in the "New Lead Belt" of southeast Missouri. The study included the evaluation of the temporal and spatial variation of dustfall and deposition rates of settleable particulate lead, zinc, copper, and cadmium, and transport and distribution of total suspended particulates and suspended particulate trace metals.

The study was conducted within a 3 x 3-mile grid around the smelter employing twenty dustfall stations and five HiVolurne samplers. The samples collected were analyzed for lead, zinc, copper and …

Study Of The Return-On-Investment Surface Of A Small Chemical Plant, Jose Antonio Casas Martinez-Ortiz

Masters Theses

"A study of the return-on-investment (ROI) surfaces for a single reactor chemical plant (Westbrook (8)) with a discontinuous investment function confirms its unimodality in the valid region. In both cases studied, the return-on-investment surfaces rise smoothly to the adiabatic boundary from a singular flow rate below which two of the component flow are not physically realizable. The optimum is located on the adiabatic boundary.

Comparison with these surfaces shows that using linear regression to obtain the parameters for an algebraic simulation of investment does not yield ROI values acceptably near the optimal. However, an heuristic approach, which assumes that minimizing …

An Investigation Of The Vertical Distribution Of Sulfur Forms In Surface Mine Spoils, Henry County, Missouri, Walter Carter Von Demfange Jr.

Masters Theses

"Samples of material in the spoil banks left by surface coal mining operations in Henry County Missouri were taken from various depths and preserved to prevent further oxidation of the pyrite in the samples. Quantitative determinations were then made for sulfate and sulfide sulfur. It was shown that near the surface the sulfide sulfur concentrations were much lower than those at greater depth while sulfate concentrations were higher near the surface than at depth. Since this is probably the effect of years of oxidation of the pyrite, it can be used to show at what depth the pyrite is being …

Waste Heat Utilization From A Direct Cycle High Temperature Gas Cooled Nuclear Reactor For District Heating And Air Conditioning, John Joseph Blase

Masters Theses

"An analysis was conducted to determine the economic as well as technical feasibility of waste heat utilization from the proposed direct cycle high temperature gas cooled nuclear reactor, as designed by the General Atomic Company.

The rejected heat from this system is at considerably higher temperatures than those normally encountered in conventional steam-electric Rankine cycles. By taking advantage of these higher rejection temperatures, heat was translated into energy available to a district heating and air conditioning service. The transportation of this energy was considered to be in the form of heated and chilled water.

A refrigeration capacity on the order …

Electrical Cable Design And Applications, Robert William Buente

Masters Theses

"The materials available for constructing various electrical cables are discussed, along with remarks/ pertaining to the attributes and limitations of each. The installation and maintenance considerations are discussed in detail. Electrical considerations involved with designing a cable system are outlined with references to their specific application. Special cable constructions, their applications, and their typical modes of installation are reviewed. The conclusion explains an overall cable system design approach along with miscellaneous information"--Abstract, page ii.

Laser Holographic Interferometric Investigation Of Heat Transfer About An Isothermal Vertical Flat Plate, Richard Michael Quinlisk

Masters Theses

"A study of the laser holographic interferometer was conducted to compare heat transfer data obtained with the device to standard free convection boundary layer theory. The system studied was an isothermal vertical flat plate. The interferometer was used to obtain fringe patterns of the boundary layer at the plate surface.

Data from the holographic interferograms were recorded by making conventional two-dimensional photographs of the holographic images.

The optical data are shown to have a good correlation to Von-Karman theory. Values of the boundary layer thickness, temperature distribution, and heat transfer were compared. An attempt was made to probe the boundary …

Two-Dimensional Radiative Transfer In A Finite Scattering Mediu, James Warren Koewing

Masters Theses

"Exact formulations are presented for the source function, intensity and flux for a two-dimensional, isotropically scattering medium of finite thickness. Spatially varying collimated and diffuse radiation of the following types are incident on the medium: (1) cosine varying, (2) semi-infinite step, (3) step at the origin, and (4) finite strip. The solutions for the cosine varying collimated boundary condition are used to construct solutions for the other boundary conditions. The two-dimensional integral equations are reduced to one-dimensional equations by separating variables. Through a series of transformations, the one-dimensional equations are put into a form in which the source function, intensity …

A Study Of Pollution Abatement From The F-15 Jet Engine Test Stand, Gary Joseph Fennewald

Masters Theses

"The pollutants emitted from jet engine test stands are carbon particles, unburned hydrocarbons, carbon monoxide, and the oxides of nitrogen. This work is a study of various ways of removing these pollutants from the test stand exhaust. The methods investigated include absorption, adsorption, electrostatic precipitation, filtration, catalytic reduction and oxidation, and thermal oxidation.

For abatement of nitrogen oxides, none of the present methods is considered to provide adequate technical reliability to proceed with an installation at this time. Each of the methods for removal of nitrogen oxides has high capital and operating cost; and, in many cases, secondary pollution problems …

Laboratory Evaluation Of Dynamic Soil Properties By Ultrasonic Testing Methods, Ronald Maurice Eckelkamp

Masters Theses

"Measurement of ultrasonic compression and shear wave velocities through a soil material has been made with a pulse wave generator developed at the University of Missouri-Rolla. The variation of these velocities along with the behavior of the dynamic material parameters of the material (Young's modulus, shear modulus, Poisson's ratio) with void ratio and degree of saturation were determined. Compression wave velocity, shear wave velocity, Young's modulus and shear modulus were found to decrease with increasing void ratio; degree of saturation was of little influence. Wave attenuation could not be measured by the test procedure used"--Abstract, page ii.

A Systems Approach To Evaluating The Effectiveness Of Training Programs, Jesse Michael Haverstick

Masters Theses

"The evaluation of the effectiveness of training programs has long been recognized as a necessity in determining the allocation of investment. However, much of industry, today, still does not use an easily administered, systematic, and reliable method for determining training program effectiveness for their salaried (managerial) personnel. It is easily seen that determining training program effectiveness is not a one-shot, one-time event, but a continual process, whose aim, ultimately, is increased productivity. For the effectiveness of a training program to be adequately monitored, these four areas should be measured: (1) trainee attitude, (2) learning, (3) behavior change, and (4) productivity …

Calculation Of The Neutron Flux In The Side Regions Of The Prestressed Concrete Reactor Vessel Of A High Temperature Gas Cooled Reactor, Richard Robert Kent Jr.

Masters Theses

"Neutron flux in the side regions of the High Temperature Gas Cooled Reactor's (HTGR) Prestressed Concrete Reactor Vessel (PCRV) was determined using the Monte Carlo method. One quarter of the PCRV was modeled, with all major structures inside it, e.g. steam generator, auxiliary cooling loop, etc. imaged at their exact position and size. Initial neutron energies range from .001 eV to 3 MeV. Three neutron interactions were considered: absorbtion, elastic scattering, and inelastic scattering.

The flux was calculated for two different PCRV temperatures, 155° F and 647° F. The thermal flux showed a minor increase at the higher temperature. In …

Diurnal Solar Heating And Cooling Of A Water Reservoir, Stephen Patrick Lepper

Masters Theses

"The transient diurnal heating of a water reservoir by solar radiation; and its cooling by surface convection, evaporation, and radiation emission was analytically modeled. The directional and spectral properties of the incident solar radiation, the air-water interface, and the selective attenuation of radiant energy by the water were properly included in the analysis. The diurnal vertical temperature distribution was predicted by numerically solving the energy equation using a finite difference technique. It was determined that the surface boundary conditions and the selective absorption of radiant energy by the water strongly influence the thermal stratification of stagnant water.

The diurnal compensating …

Transformer Connection Study For 138 Kv To 12.47 Kv Substations Of The Union Electric Company St. Louis, Missouri, John Glenn Walsh

Masters Theses

"This thesis examines the transformer connections that can be used in the new 138-12.47 kV substations on the Union Electric power system. The object is to determine if a zero phase shift transformer without a delta connected tertiary winding can be used and economically justified. Traditionally a delta winding has been automatically included for this application without taking engineering time and effort to study all ramifications including possible dollar savings available with other connections. Three transformer manufacturers supplied technical and cost data which are analyzed, based on Union Electric system conditions. Consideration of relaying, harmonics and unbalanced loading shows that …

Determination Of Oxygen Chemical Diffusion Coefficients In Single Crystal Strontium Titanate By Capacitance Manometry, Douglas Bugh Schwarz

Masters Theses

"The use of the tensi-volumetric apparatus to study the non-stoichiometric behavior of strontium titanate was discussed. Oxidation kinetics of reduced single crystal strontium titanate were measured with an ultrasensitive capacitance manometer as the sample absorbed oxygen in response to a changing oxygen activity.

The oxidation kinetics were found to fit a solution to Fick's second law for rectangularly shaped samples....

The procedure selected for measurement of the oxidation kinetics, and the method of obtaining diffusion coefficients from the oxidation data was discussed along with potential sources of error of the system"--Abstract, page ii.

Synthesis Of Fused Silica By Flame Hydrolysis, James Edward Rourke

Masters Theses

"Apparatus to synthesize and dope high purity, optical quality fused silica by flame hydrolysis was constructed. Fused silica samples containing 0, <35, 35 and 90 ppm niobium were synthesized and characterized by the following properties: purity, refractive index, radiation damage resistance, and transmission spectra. The properties of the undoped sample were shown to be comparable to those of available commercial fused silica. Deviations in the properties of the doped samples from those of the undoped samples were explained in terms of the niobium content"--Abstract, page ii.

Inertial Navigation Performance Improvement Realized By The Technique Of Interrupted Alignment, Ralph E. Herndon

Masters Theses

"Present on-aircraft ground alignment gyro bias methods can basically be categorized as (1) periodic maintenance performed by the ground crew, (2) pre-flight calibration requiring a two-position gyro compass alignment or (3) optimal filter estimation of the north gyro bias error.

This thesis discussion presents an interrupted alignment method that allows adequate level axes gyro bias correction without the restrictions associated with a conventional two-position gyrocompass alignment (i.e., a minimum time for bias calibration on a steady aircraft). The interrupted alignment technique allows the pilot to select the navigate mode at any point during gyrocompass and reselect the align mode at …

A Thin Film Evaporator Rate Controller, Daniel Robert Kasterlein

Masters Theses

"A circuit is described which is used to control the evaporation rate of material from a resistance heated boat or electron beam evaporator. The rate controller is used in conjunction with a quartz crystal thickness monitor in a vacuum evaporator"--Abstract, page ii.

The Study Of Sulfur Dioxide Distribution Surrounding A Lead Smelting Industry In The New Lead Belt Of Southeastern Missouri, Jeng-Sheng Hwang

Masters Theses

"The purpose of this investigation was to study the magnitude and distribution of sulfur dioxide in the air surrounding the smelter of Missouri Lead Operating Company (now AMAX Lead Company of Missouri) in southeast Missouri, and evaluate the inter-relationships between sulfur dioxide incidents, meteorological factors, and plant operations.

Field research was conducted employing two weather stations and three sulfur dioxide monitoring stations. The data obtained from strip charts at each station were recorded and analyzed manually as well as by UMR computer facilities. From the studies conducted, it was found that the annual predominant winds occurred from S and SE …

Numerical Calculation Of The Currents In Bent Wire Antennas, Min Ho Kang

Masters Theses

"The current distribution for bent dipole antennas is numerically calculated by using a digital computer. A delta-gap at the center is assumed for the drive. Several different bend-angles are considered including the cases of the straight wire and the inverted-L. The total length of the wire considered is λ/2 while the ratio of the bent portion over the vertical portion is varied. The method of solution is based on Mei's integral equation and the method of moments. The use of Mei's integral equation eliminates the need for the application of the boundary condition at the point of bending. For …

Experimental Analysis Of V-Belt Tensile Loads, John Mark Wiesehan

Masters Theses

"An experimental investigation was conducted to determine the magnitude of v-belt stresses in automotive drive situations. A constant tension belt test apparatus was designed and fabricated using a variable speed cradled D.C. motor for power and two automotive alternators for absorption.

Free span stresses on the dynamic torque loaded belt drive were determined from the equations governing a pivoted drive system. Centrifugal stress was determined by a theoretical analysis of belt motion. Bending stresses were obtained from a static test employing strain gages mounted on the top of belts with exposed cord layers. The variation in load stress around the …