Engineering Commons^™

An Application Of Infrared Spectroscopy To The Study Of Binder Migration In Paper Coatings, Fred E. Huang

Masters Theses

Multiple internal reflectance (MIR) was used to study binder migration of paper coatings. Casein and an acrylic latex were selected as binders because of their characteristic infrared absorption bands. The coatings analyzed were prepared on the Western Michigan University Pilot Coater using the airknife coating method at different coating speeds. A surface grinder was used to obtain several layers of coating for surface studies.

It was concluded that the MIR technique could satisfactorily be used in the binder migration studies. Its success mainly depends on the precision of surface grinding, caliper measurement and infrared characteristics of the binders. The results …

Theoretical Thermodynamic Functions For Argon, Peter Yi-Ren Sheh

Masters Theses

No abstract provided.

A Fluid Control System For The University Of Missouri--Rolla Nuclear Reactor, Billy Roger Mcpherson

Masters Theses

"Solid control rods and their movement through a reactor core present problems inherent in any moving machinery. The problems of binding, wear, and noise have to be dealt with in the usage of a solid control rod system. Therefore, an alternate system that eliminates or minimizes these problems would lower maintenance costs, extend the lifetime of the control system, and produce safer operating conditions.

This thesis presents a control system that has no moving parts inside the reactor core. The system is based upon a neutron-absorbing fluid containe��d in hollow tubes in the reactor core. The fluid level is operated …

Thermal Response Of A Composite Bridge Structure, David John Wisch

Masters Theses

"This experimental investigation was conducted as an intermediate study to verify and substantiate a prior theoretical study for possible utilization toward development of rational bridge design criteria. The objectives of the study were to construct and instrument a 15 ft - 15 ft (4.6 m- 4.6 m) two-span, composite design, laboratory structure, to subject the structure to thermal loading, and to correlate the experimental temperature distributions, strain distributions, and deflections with those obtained from the theoretical study. Infrared heat lamps were used to obtain steady-state thermal loading.

Three theoretical cases were considered for strain calculations: a) both the slab and …

Dynamic Pullout Resistance Of Anchors Buried In Dry Sand, Chris John Veesaert

Masters Theses

"The vertical pullout resistance of buried anchors subjected to dynamic loading was investigated by means of a laboratory model study. A dry uniformly graded sand, compacted by vibration to 92% of its relative density, was used as the test medium. Tests were performed in a 24-inch square tank using 3.0 and 5.0-inch diameter half and full-anchors. The anchors were tested at depths ranging from 5.0 to 21.0 inches.

It was assumed that the dynamic failure mechanism of earth anchors was the same as the static failure mode, and not distinct behavior. Thus static tests, i.e., tests using a constant strain …

Removal Of Organic Chemical Contaminants By Granular Activated Carbon., Garry Reinhold Aronberg

Masters Theses

"The purpose of this investigation was to evaluate the effectiveness of GAC* filtration in removing organic chemical contaminants from drinking water, and to determine whether the T.O. No. of the treated water could aid in the routine monitoring of the GAC filters.

Two pilot filters containing 18-in. (45.7-cm) deep GAC beds were installed at water treatment plants in Jefferson City and St. Louis County, MO; both plants treated Missouri River water. A bituminous coal-base (large surface area, small pore volume) and 2 lignite coal-base (small surface area, large pore volume) carbons were tested at 2 and 5 gpm/sq ft (81.4 …

An Evaluation Of Productivity And Efficiency In Work Scheduling In A Public Works Department, Kraig L. Gordon

Masters Theses

“Managers throughout the world frequently associate the meanings of productivity and efficiency with the capabilities and performance of employees. This approach is limited since productivity entails far more than the output of the labor force. The factors affecting productivity need evaluating to determine the significance they plan in the overall process.

Industry has attempted to improve its productivity posture by utilizing a multitude of concepts. Some of these concepts are time and motion studies and process planning. However, in the public sector, literature shows that little has been attempted to improve the productivity in public organizations.

The greatest portion of …

Effects Of Rheology On Pigmented Size Press Coating Pattern, Stanley L. Oakleaf

Masters Theses

No abstract provided.

Electronic Contribution To Magneto-Thermoelectric Power In Many-Valley Model Of N-Ge, Carlos Humberto Munera

Masters Theses

No abstract provided.

Ohmic Magnetoresistance In Nonparabolic Semiconductors: Application To N-Insb, Mahmoud Jaafarian

Masters Theses

No abstract provided.

Influence Of Turbidity On The Stratification Development Of A Deep Water Reservoir., David Allen Prouty

Masters Theses

"The influence of turbidity on the diurnal temperature distribution and thermocline development in a deep water impoundment which is exposed to heating and cooling loads by convection, evaporation, and radiation is examined analytically. The diurnal behavior of the solar load, directional and spectral, is used with an isotropic multiple scattering model to simulate the attenuation of solar flux by turbid water. The diurnal behavior of the ambient temperature, humidity and wind speed were mathematically modeled to simulate the local (Phelps Co.) spring time of the year. The combined conduction and radiation energy transfer through the water was treated as a …

Non-Cash Incentives And Worker Motivation, Daniel Franklin Cole

Masters Theses

"A problem of growing concern in the United States deals with the poor results of the nation's businesses in terms of productivity. The U.S. is now suffering the worst decline in productivity in a generation. While part of this decline can be attributed to economic conditions, data indicates that the labor force could be more productive if it wanted to do so. A study has shown that 52% of all workers feel they aren't producing at full capacity. Alienation of the American worker is identified as one of the most important contributors to this problem.

Because it is often difficult …

Solar Heat Capacitors, Taddesse Aregahegn

Masters Theses

No abstract provided.

Inhibitors And Retarders For The Free Radical Polymerization Of Alpha-Methylstyrene, Alexander Accetta

Masters Theses

No abstract provided.

Vapor Pressures For The Ternary System 1-Butene, Isobutane, And 1, 3-Butadiene., Kevin Steele

Masters Theses

"An innovative apparatus suitable for the rapid but accurate measurement of vapor pressures of liquid solutions is described. Liquid solutions of known composition are prepared in a test cell by volumetric metering of degassed liquids. The operation of the apparatus is feasible over a wide range of temperature and pressure, producing data with an estimated probable error of ± 0.05 percent. Experimental P-X data for a system of C₄ hydrocarbons (1-Butene, Isobutane, and 1,3- Butadiene) are reported from 40-160 degrees Fahrenheit. The data are in agreement with the literature, and vapor pressures are expressed as a function of temperature …

An Analysis Of The Role And Effectiveness Of The Contract Manager In Government Contracting., Daniel Martin Wilson

Masters Theses

"The contract manager in carrying out the contract management function of government contracting represents a vital element of the procurement process. He is charged with responsibilities for assuring that a product or service is delivered in a timely manner and is of specified quality, quantity and price. However, research and a survey of his role reveal that he is regarded a s a functional specialist, guided by a mass of procedural requirements, and he is not included in the managerial hierarchy of contracting.

Because his role does not accord him the status or authority commensurate with the importance of the …

Estimation Of Vehicle Transfer Functions., Leonard Francis Laskowski Iii

Masters Theses

"This study is an investigation of several techniques used to estimate lateral control models for vehicles. The lateral control model that was identified related steering wheel angle input to lateral acceleration output. Two different order models were identified, one a biquadratic and the other a fourth order lowpass system with second order numerator dynamics. The two main approaches investigated were:

1) Regression analysis

2) Fast Fourier Transform Techniques These techniques were chosen because of their inherent immunity to noise.

A CSMP simulation of all identified models was then made to determine their validity. These checks were made using laboratory data …

Analysis Of The Stresses Induced In Rock By Rock Splitters., Diogenes De Jesus Chollett

Masters Theses

"The method of solution of the problem of determining the stress and displacement distributions around an unfractured circular hole subjected to nonuniform applied internal pressure located in an infinite plate is developed. Two problems are solved for two different representative boundary conditions. The problem of determining the stress distribution around a circular hole with two symmetric radial cracks subjected to nonuniform applied radial pressure located in an infinite plate is analyzed and developed for further solution"-- Abstract, p. ii

Disposal Of Lead And Zinc Cationic Wastes On Soils., Stephen Melvin Linnemann

Masters Theses

"The sorption and desorption of lead and zinc on soil samples from the "New Lead Belt" of southeastern Missouri and from Springfield, Missouri, were investigated using both column and batch systems. These cations were selected for study because of the possible effects which soil pollution in the "New Lead Belt" mining region could have on shallow aquifers and because both metals are utilized in the electroplating industry.

It was found that soil has the ability to sorb lead and zinc; however, the cation-exchange capacity (C.E.C.) of the soils studied was not fully satisfied, though there was evidence that i f …

A Unit Hydrograph For The Missouri Ozark Region., Melvin G. Schaefer

Masters Theses

"Eleven small watersheds from the Missouri Ozark region are used in generating a synthetic unit hydrograph. The analysis is composed of three parts: First, a prediction equation is developed which correlates the time lag parameter with the physical features of the watershed. Second, an equation is developed which predicts the peak flow ordinate for 30-, 60- and 120-minute unit hydrographs. Third, an average dimensionless unit hydrograph is determined"-- Abstract, p. iii

An Investigation Into The Extent Of Implementation Of Operations Research Techniques For Inventory Control In Industry., Edward Allen Scarff

Masters Theses

"The object of this research is to investigate the techniques currently utilized for controlling inventories in industry. The various significant methods of inventory control in use today are presented and the strengths and weaknesses of these methods are assessed.

A survey of the Fortune 500 companies was conducted to determine the methods of inventory control in use today by industry. In addition, selected production personnel of representative companies were interviewed to determine the advantages and disadvantages of certain inventory control methods they use.

The results of the survey and the interviews are presented, and an analysis is made. Conclusions are …

Electroless And Chemical Metal Deposition On Human Tooth Enamel., Richard Doyle Christie

Masters Theses

"Initial investigations have confirmed the feasibility of depositing an adherent metal film onto tooth enamel. Such films might be used as pit and fissure sealants in preventive dentistry, with denture or orthodontic work, as an intermediate substrate with various organic or inorganic restorative materials, or other such areas. The process employs chemical solutions containing ions of the metal to be deposited and suitable reducing agent solutions.

To date, metallic copper and silver films have been plated onto teeth in vitro. The deposits are quite adherent and appear to exhibit the conductivity, crystal structure, luster, hardness, and other chemical and physical …

Investigation Of A Modulation Method And Signal Processing Techniques For Digital Data Transmission In Hf Channels., Michael Ray Campbell

Masters Theses

"This thesis presents a method of improving the performance of digital communication systems operating in environments typical of the high-frequency (HF) band. The HF channel is a compound error event channel in that it contains random errors due to additive white Gaussian noise (AWGN) plus burst-type errors due to effects such as impulse noise and tone interference. A method of signal design using the time-frequency plane is utilized. This facilitates design of signal sets that may be blanked in time and frequency, thus reducing the effects of the nonGaussian interference. Several signal designs are presented and compared in t􀁗rms of …

Theoretical And Experimental Investigation Of A Viscous Ring Nutation Damper., Roy Alexander Campbell Iii

Masters Theses

"The dynamics of passive dampers applied to high s peed gyro systems is reviewed briefly and the partially filled viscous ring nutation damper is investigated. Particular attention is given to 1 the broken ring or nutation synchronous configuration where the fluid moves as a rigid slug and the damping is greatest. In this mode the damping is assumed to be viscous and expressions for a linear damping constant are presented. Data from an experimental, high-speed gyro is used to verify the theoretical analysis"-- Abstract, p. 1

Project Program Evaluation Technique For Real Property Maintenance Activities., Richard Walter Graumann

Masters Theses

"Managers of Real Property Maintenance Activities often only consider workmanship and customer satisfaction when evaluating the overall effectiveness of their contracted maintenance and construction projects. For multi-functional organizations where top management is responsible for the execution of several hundred concurrent, unrelated, unique, and widely dispersed projects, these subjective factors are not adequate to conduct a meaningful evaluation.

Top management must continually assess not only the progress of contracted work, but also the engineering design and contract administration functions. Published material has given little attention to the need for aggregating project data in a multi-project environment to provide management with the …

Experimental Investigation Of Supporting Wire Interference Effects In The Supersonic Near Wakes Of Slender Bodies., Dale M. Pitt

Masters Theses

"It is generally recognized that the presence of a model support sting i s likely to affect the model's base pressure and wake characteristics. The use of a wire-supported model is usually relied upon to obtain minimum disturbance measurements in the model's wake. Investigations into the disturbances caused by different size supporting wires have been conducted with the use of a 16-degree wedge and cone. The tests were conducted in the University of Missouri-Rolla axisymmetric supersonic wind tunnel at Mach 3.15, and at a Reynolds number of 2.14 X 10⁶ per inch. Pitot pressure traverses were made in the …

A Strategic Planning Model For Implementing Community Development Block Grant Programs., John M. Lang

Masters Theses

"As problems of metropolitan areas have multiplied, the federal government has been drawn into an ever-increasing intimate funding association with city governments. Although federal funding for ii urban problems may have been considered a panacea by some, most local government agencies have now discovered that their problem has shifted in emphasis from where to find funds to that of meeting federal standards and requirements of application in order to get the funds.

The impact of federal programs on local government management is evident in the recently enacted federal Housing and Community Development Act of 1974. Title I of the act …

Universality Of Management Principles And Applicability Of American Management Know-How In Less Developed Countries., Minas Lessanu

Masters Theses

"The title is the Universality of management principle through the history and development of management thoughts. It illustrates the gradual education of management principles. Then it goes on to discuss certain problems of the field of management, in particular the problems associated with semetics.

The thesis then discloses the different management principles in the different managerial functions of planning, organizing staffing and controlling. It then shows these principles to be universal and finally discloses the different environmental constraints that evolved and concludes that they are universal, but their applicability is to a certain extent possible and highly dependent on the …

A Study Of The Potential Performance Improvements Available From The Ga(W)-1 Airfoil As Compared To The Naca 2412 Airfoil., Robert Keith Rice

Masters Theses

"A direct comparison of the current NACA 2412 section general aviation airfoil and the recently developed GA(W)-1 airfoil was conducted in the University of Missouri - Rolla's subsonic wind tunnel. Finite aspect ratio performance of both airfoils equipped with 30 percent chord flaps was studied to predict possible performance gains for general aviation aircraft available from the GA(W)-1 section.

Results show that the NACA 2412 airfoil with a standard slotted type flap gives a maximum lift coefficient of 1.88 with the flap deflected 30 degrees and a test Reynolds number of 4.Sxl0 5 based on wing chord. The GA(W)-1 section …

Creep And Stiffness Of Full Column Resin Grouted Roof Bolts., Wesley Clare Patrick

Masters Theses

"A three-phase test program was utilized to evaluate some creep and stiffness parameters of several types of full-column resin-grouted roof-bolt installations. The tests indicate that: (1) a large percentage of an applied load bleeds off during the first 100 hours subsequent to bolt installation; (2) the amount of load bleed-off is a f unction of the grout annulus size and the bolt surface roughness; (3) retightening of grouted rock bolts reduces the magnitude and rate of the load bleed-off phenomenon; and (4) resin-grouted roof bolts provide a stiffer roof support system in that bolt elongation resulting from an applied load, …