Engineering Commons^™

Universal Electric And Magnetic Fields Analyzer System, Yong Cheh Ho

Masters Theses

"Near-field probing is often used to measure the electric and magnetic fields above a printed circuit board (PCB) or integrated circuits (IC) chip in order to identify the sources and coupling paths of an electromagnetic interference (EMI) problem.

A wideband universal field analyzer was designed, built and tested in this thesis. The system is able to provide fast field scanning over a wide frequency range in lieu of its capabilities to measure multiple field components using a single probe design. Central to the system operation is the phase-shifting concept that provides wideband and wide- range phase-shifting.

The complete universal field …

An Approach For Human Swarm Interaction, Shishir Bashyal

Masters Theses

"This study shows that appropriate human interaction can benefit a swarm of robots to reach to goal more efficiently. The common belief in swarm robotics that user intervention adversely affects intelligence of the swarm is studied carefully to show that the traditional human-robot interaction approaches are not suitable for human swarm interaction. A set of desirable features for human swarm interaction is identified and an interaction architecture is proposed that has all of the desirable features. A swarm simulation environment is then created that allows simulating a swarm behavior in an indoor environment. Three different applications of the swarm are …

Synthesis Of Nanostructured Conducting Polymers And Their Application As Gas Sensors, Zhe-Fei Li

Masters Theses

"A single-step, bottom-up technique based on a nanostructured conducting polymer has been used to fabricate sensors. Small amounts of aqueous solutions of aniline, a dopant, and an oxidant were placed on an interdigitated electrode array. Ultraviolet (UV)-irradiation of the solutions enhanced polymerization, yielding a highly porous film of polyaniline nanofibers with mean diameters of around 100 nm and lengths on the order of 1 µm. Solutions that were not irradiated formed bulk-like polyaniline films. Nanofibers and bulk polyaniline sensors were exposed to vapors in an argon carrier gas including: chloroform, a weak proton donor; toluene, a vapor that causes polymer …

Thermal Characterization And Vibration Of Solder Alloys, Brandon Lee Brinkmeyer

Masters Theses

"Recent legislation and growing environmental concerns have forced the electronics industry to discontinue the use of tin-lead (SnPb) solder. Although the legislation did not directly affect aerospace and defense industries, future transitions to lead-free (LF) solders are inevitable. Differences exist between these high reliability systems and consumer electronics, first of which is a very small production rate and a long life cycle which often leads to repair or rework procedures which introduce the potential for mixing of SnPb and LF solder. In this study, Sn-3Ag-0.5Cu (SAC305) was mixed with Sn-37Pb solder in amounts of 0, 25, 50, 75, and 100 …

Wireless Mote-Based In-Process Diagnostics Using Hand-Held Tools In Network Enabled Manufacturing Environments, Reghu Anguswamy

Masters Theses

"When complex manufacturing systems are considered, post process inspection can be a very time consuming and costly. In addition, no inspection data is typically collected unless a major problem is encountered. Real-time monitoring of the manufacturing processes and verification of its product quality are two important factors to reduce the manufacturing lead time and to ensure safety and quality.

In this thesis, a diagnostics and root-cause analysis scheme with a single channel wireless routing protocol for real-time monitoring of process quality of pull-type fastening operations is first presented. The overall architecture has been implemented on a Huck45 pull-type tool, which …

Application Of Multi-Modal Fusion Techniques For Corrosion Detection And Characterization In Aging Aircraft Components, Soumya De

Masters Theses

"The United States Air Force (USAF) recently estimated that corrosion maintenance costs exceed $800M per year. Given this, it is desirable to reduce the amount of "find it-fix it" corrosion maintenance activities. One method is to introduce a damage tolerance approach for corrosion detection. In order for this to become a reality, a comprehensive snapshot of corrosion present must be generated.

This thesis presents a data fusion process to perform uni- and multi-modal nondestructive testing and evaluation of corrosion under paint and in lap joints for volumetric characterization. The process for analyzing a given structure includes: 1) the acquisition of …

Behavior Of Full-Scale Rc T-Beams Strengthened In Shear With Externally Bonded Frp Sheets, Antonio Brancaccio

Masters Theses

"Shear deficiencies in many bridges may be considered even more critical than flexural deficiencies since shear failures occur without advance warning and are more catastrophic. Deficiencies in shear can be due to insufficient shear reinforcement, use of outdated design codes, a reduction in the steel area due to corrosion, or an increase in the service load due to change of occupancy for the structure.

In recent years, many research studies have investigated the shear behavior of reinforced concrete (RC) beams strengthened with fiber-reinforced polymer (FRP) composites, however, most of them were conducted on small-scale specimens. Thus, analytical models and design …

Release And Removal Of Microcystins From Microcystis During Disinfection Treatments, Jie Ding

Masters Theses

"The presence of algal toxins, or cyanotoxins, in surface water has been increasingly reported. These highly hazardous toxins are potential threat to both human health and animals by contaminating drinking water sources over the world. In this research project, inactivation of Microcystis aeruginosa cells and release and removal of intracellular microcystins during several oxidative and physical treatments was studied. The results of this study show that chlorine dioxide, sonication, low salinity and quick blending with tissuemiser caused immediate release of microcystin-LR to water after treatment. No significant increase of toxin level was observed after treatment with free chlorine, ozone, permanganate, …

Elevated Temperature Behavior Of A Magnesium Based Bulk Metallic Glass, Neal C. Ross

Masters Theses

"Bulk metallic glasses are a new material set that possess interesting and exceptional engineering properties. Their study has been a major focus of research in metallurgy since the early 1990s, and recently their properties have led to application in specialized applications. Limitations including material cost, maximum attainable cast diameters, and high density have prevented the widespread use of these materials. In particular, the high density of most bulk metallic glasses has significantly reduced their appeal to the aerospace community. In an effort to overcome this, research is being performed on producing lower density glass forming systems based on magnesium and …

Modeling Kinetics Of Hydrolysis Of Three Pesticides In Laboratory Waters, Michelle Kim Marincel

Masters Theses

"Pesticides and pesticide degradates found in drinking water sources are of particular concern to human health. When treated and disinfected at a drinking water plant, pesticides etridiazole, metribuzin, and diazinon undergo many treatment processes including lime softening, where the water pH is raised to 10 for calcium removal or 11 for magnesium removal. This thesis focuses on modeling the kinetics of hydrolysis of three pesticides that have the potential to undergo hydrolysis in drinking water plants. Linearly and non-linearly regressed first order and non-linearly regressed second order models were applied to the experimental data and compared to limited literature values. …

Flow Structures In An Enclosed Simplified Full Scale Under-Hood Engine Compartment During Steady State Operation, Chin Hoong Leong

Masters Theses

An experimental study of flow structures in an enclosed simplified full scale under-hood engine compartment will be conducted during steady state operation using whole field velocity measuring technique. 2D Particle Image Velocimetry (PIV) is planned for multiple cross sections in the test volume. Emphasis is given on understanding the flow structures of the 3D under-hood flow using multiple 2D PIV measurements. A recent study conducted on the engine compartment only consists of three 2D PIV measurement cross sections that sufficiently display 2D flow behavior at specific regions. Therefore, a detailed 3D flow mapping in the enclosure on various cross sections …

Deconvolution And Segmentation Of Ground Penetrating Radar Images, Vincent Krause

Masters Theses

Ground Penetrating Radar is a valuable tool for infrastructure condition evaluation as well as in archaeology and geology. The image produced by a GPR scan can be difficult to interpret due to the weak reflection amplitude, the overlap of reflections, and due to outside interference. This thesis proposes an algorithm to automate GPR scan interpretation. This will enable maintenance engineers to read GPR scans quickly and accurately.

The proposed algorithm framework uses an optimization-based deconvolution technique followed by a segmentation process. Each column of the image is deconvoluted and thus reducing them to a list of ordered pairs of reflection …

A Practical Guideline For Establishing Non-Return Valve Specification And Performance Criteria, Eric W. Dawkins

Masters Theses

The non-return valve has been a standard piece of equipment in the injection molding industry since the reciprocating screw was developed. Most molders understand the role of the non-return valve in the molding process. But few understand the functional problems of the non-return valve. Because of this, the non-return valve has been considered a nuisance item for injection molders.

Wear of the non-return valve is another problem that molders are faced with. The factors contributing toward wear are not entirely understood. Material, temperatures, hours and machine size, etc., all effect the life of a valve. Consequently, most worn valves are …

Security Printing: Towards Hologram Printing, Sachin Ravindra Agate

Masters Theses

Today we are facing many situations where the genuineness of the products and documents is questioned. Counterfeiting the original products has become a business of few people, which result in the degradation of quality of products, loss of money and loss of faith of end user. To prevent such malicious act, security features are added in the final product. Security printing is one of those methods that help in preventing counterfeit products and treachery. There are many different security features, which can be added in the security printing. Apart from those features, an embossed hologram is also included in prints …

Health Monitoring Of Concrete Bridges Utilizing Sensor Technology, Ammar Zalt

Masters Theses

Structural health monitoring using sensor technology is a promising way to provide excellent means for protecting important structures such as bridges, dams, and nuclear reactors. These sensors provide real-time information about structural conditions, They work together as a nervous system to provide timely information for emergency and risk mitigation. The information obtained from these sensors can later be analyzed and compared to the design data so that the problem can be detected and fixed before it develops into a serious and costly hazard.

Throughout the course of this thesis the feasibility and performance of two types of sensors will be …

Transceiver Design And Radio Frequency Integrated Circuits Evaluation Via Electronic Design Automation, Yu Ming Chen

Masters Theses

This thesis study presents the theory and design methodology of Radio Frequency Integrated Circuits (RFIC) and analyzes a RF frond-end receiver and down-conversion mixers using circuit evaluation tools. The theory of RF is described on both architectures and circuit levels with respect to monolithic implementation in integrated semiconductor technologies. The design methodology provides an efficient and practical way to approach ·the theoretical values by using an Electronic Design Automation (EDA) tool called Cadence Virtuoso custom design platform Based on the libraries provided by the Cadence Virtuoso, a Heterodyne receiver and two Gilbert mixer circuits have . been evaluated through the …

Data Fusion Technique For Measuring Intersection Delay Using Gps-Enabled Probe Vehicles, Byung-Hee Han

Masters Theses

Intersection control delay is considered a primary measure for determining the level of service at signalized intersections. This thesis develops a technique estimating intersection delay using GPS data from GPS-enabled vehicles. First, this study analyzes existing methods that estimate control delays using GPS data and proposes an improved technique in response to the weakness of those methods. The proposed method estimates the control delay well with better accuracy covering the weaknesses. However, the control delay from the GPS data has a sample size problem for determining the level of service at signalized intersections. Therefore, this thesis proposes a data fusion …

Development Of Knowledge Base Of Concrete Bridge Maintenance System, Bahre Karam

Masters Theses

Bridges are the key elements of any transportation system of a country. Bridges are expensive structures and therefore, it's essential to maintain and repair them on regular basis. Almost one third of the bridges in United States are reported to be in some what deteriorated conditions. This Research presents the development of knowledge base for decision support system for concrete bridges.

During this research various concrete bridge problems are investigated including COlTosion, delamination, cracks, spalling and scour etc. The inspection tools and techniques are addressed in order to identify these problems both for above and below water surface. The various …

Wimax Software Defined Radio, Assad Saleem

Masters Theses

As processors and configurable devices are getting faster and smaller, they are giving rise to better solutions for various communications systems and standards. In this paper, the implementation of a software defined radio for WiMAX is presented. This paper highlights the system model for simulation to achieve better understanding of the system, which was developed in MATLAB. Also, included in the paper is the discussion of the physical implementation of this communication system. The system is build around National Instruments’ PCI 5640 hardware which features a Xilinx Virtex-II FPGA. Naturally, LabVIEW was the tool used to implement the hardware/software co-design.

Experimental Measurements And Mathematical Modeling Of The Rigid Capillary Dewatering, Vrajesh N. Chokshi

Masters Theses

Rigid Capillary Dewatering (RCD) technology is a process in which water is removed from a wet paper web by capillary dewatering action without excessive mechanical compaction of the fiber furnish. Operating conditions on the Rigid Capillary Pressing (RCP) roll, and properties of paper and pulp determines the dewatering behavior of the RCD technology.

The dewatering behavior of the RCD technology is studied in four sets of experiments performed using different operating conditions, on a paper pilot machine at a Western Michigan University (WMU) facility. The solids content of the paper web before and after the RCP roll in the press …

A Computer Aided Diagnosis System For Breast Cancer Using Independent Component Analysis And Fuzzy Classifier, Fadi Abu-Amara

Masters Theses

Screening mammograms by a radiologist is a repetitive task that causes fatigue and eye strain. For every thousand cases analyzed by a radiologist, only 3 to 4 are cancerous and thus an abnormality may be overlooked. Computer-Aided Detection (CAD) algorithms have been developed to assist radiologists in detecting mammographic lesions. CAD algorithms have improved total radiologists' detection accuracy of cancerous tissues. In this thesis, a computer aided detection and diagnosis (CADD) system for breast cancer is developed. The algorithm framework is based on combining principal component analysis (PCA), independent component analysis (ICA), and fuzzy classifier to identify and label suspicious …

An Upper Extremity Biomechanical Model: Application To The Bicep Curl, Adam Miller

Masters Theses

An upper extremity biomechanical model was developed based on recommendations provided by the International Society of Biomechanics. The model was used to investigate biomechanical differences between two variations of the bicep curl exercise: the standing and incline dumbbell curls. An 8-camera Vicon motion capture system was used to collect data on five subjects that executed 10 repetitions of each type of curl.

Four key biomechanical indicator variables were investigated: range of motion, maximum elbow flexion moment, mean elbow flexion moment, and the flexion angle at which the maximum flexion moment occurs. On average, the range of motion at the elbow …

The Importance And Influence Of Groundwater Fluctuations In Phytoremediation, Jeff A. Weishaar

Masters Theses

"The primary purpose of this research is to study the relationship between microbial degradation and plant uptake of volatile hydrocarbons, such as benzene, toluene, ethylbenzene and xylene. While these compounds are known to biodegrade and are capable of transport into plant tissue, any relationship between the two removal mechanisms remains largely unknown. The goal of this work is to better understand the interactions of these multiple biological processes within a phtytoremediation effort"--Introduction, page 3.

Performance Evaluation Of Existing Analytical Methods To Compute The Shear Contribution Provided By Externally Bonded Frp Sheets In Concrete Structures, Rocio Patricia Tumialan

Masters Theses

"External application of FRP composites has been adopted for strengthening and/or repair of concrete structures in many applications during the last two decades. However, the research into shear strengthening using FRP composites has not been widely conducted as compared to flexural strengthening and axial load capacity increase, and the results obtained thus far are scarce and sometimes controversial. This study presents a review of analytical studies and design guidelines on shear strengthening of concrete structures with externally-bonded FRP laminates, and their assessment with experimental data collected from the literature. The strengths and weaknesses of each model and design guidelines/codes/specifications are …

Diversity Techniques For Signal-Strength Based Indoor Location Determination, Anil Ramachandran

Masters Theses

"Diversity techniques have been found in the literature to be suitable for compensating channel uncertainties such as multipath fading. In this thesis, we exploit spatial and frequency diversity techniques for improving accuracy in locating stationary and mobile objects in the indoor environment"--Abstract, page iv.

Manufacturing Of Glass Ribbon Reinforced Transparent Composites Using The Autoclave Process, Josef Patrick Seale

Masters Theses

"Clear transparent panels have many applications ranging from windows on an aircraft to protective safety guards on industrial equipment. Glass ribbon reinforced transparent composites are light weight, load bearing and have a high impact resistance.

A transparent composite is based on the concept of matching the refractive index of the glass ribbon with that of a resin system. It is not necessary that the resin refractive index match the glass refractive index before the cure cycle, only that the refractive indexes match after curing.

Transparent composites have a high impact resistance that would be mechanically ideal for aircraft windows and …

Experimental Investigation Of Temperature And Tool Wear In High Speed End-Milling Of Titanium Alloy, Benjamin Nwakile Oguejiofor

Masters Theses

"This thesis presents the results of experimental investigation of temperature and tool wear in high speed end-milling of titanium alloy. The investigation of cutting parameters on temperature in high speed end-milling of thin-walled titanium structure was conducted on Cincinnati Milacron Sabre 750 Vertical Machining Center using a 1/2 Fractional Factorial Design of Experiment with 3 factors at 2 levels each. Data logging of temperature data was carried out using VI logger software. Tool tip temperature at the comers and center of the pocket was estimated. All the factors investigated were found to have a significant effect on workpiece temperature. Radial …

Performance Improvement Of Adaptive Filters For Echo Cancellation Applications, Deepak Challa

Masters Theses

"This work focuses on performance improvement of adaptive algorithms for both line and acoustic echo cancellation applications. Echo in telephone networks, Line Echo, is observed naturally due to impedance mismatches at the long-distance/local-loop interface. Acoustic echo is due to the acoustic coupling between the microphone and the speaker of a speakerphone. The Affine Projection (APA) and the Fast Affine Projection (FAP) algorithms are two examples of reliable and efficient adaptive filters used for echo cancellation...This thesis presents, Variable Regularized Fast Affine Projections (VR-FAP) algorithm, with a varying, optimal regularization value which provides the desirable property of both fast and low …

Low-Thrust Control Of A Lunar Orbiter, Nathan Harl

Masters Theses

"This thesis presents a method for maintaining a long-term lunar Sun-synchronous orbit using continuous low-thrust hardware. The control method is developed using optimal control theory, which involves controlling a system through the minimization of a desired cost function"--Abstract, page iii.

Operation Of A Brushless Dc Drive For Application In Hybrid Electric Vehicles, James Scott Jenkins

Masters Theses

"One of the goals of a hybrid electric vehicle design is to improve the overall performance of the vehicle by incorporating several different power sources in such a way as to maximize the energy usage. By combining the desirable characteristics of each of the components in the system, the vehicle becomes more efficient to operate. Energy storage systems such as batteries and ultra-capacitors can be used to supply or store energy from the system when needed. The primary power source in this model will be an internal combustion engine coupled with a permanent magnet synchronous generator. The purpose of this …