Engineering Commons^™

An Experimentally Generated Constitutive Model For Peak Stress (Σ_Peak) In Compression Samples, Kevin Mathew Lopez Galang

Master's Theses

The hot working behavior of AISI 1018 steel was studied by hot-compression deformation tests on the Gleeble 1500 thermo-mechanical simulator at true strain values of -0.143 and -0.405, true strain rate values of 0.01 and 0.1, and working temperatures of 900^°C and 1000°C. The tests show that a lower working temperature and lower true strain value results in a greater maximum compressive force. The apparent activation energy Q_app was calculated by using the Zener-Hollomon parameter combined with the low stress law. Q_{app ­}was calculated to be 311 kJ mol^-1 K^-1.

Voltage Stability Analysis Using Simulated Synchrophasor Measurements, Allan Agatep

Master's Theses

An increase in demand for electric power has forced utility transmission systems to continuously operate under stressed conditions, which are close to instability limits. Operating power systems under such conditions along with inadequate reactive power reserves initiates a sequence of voltage instability points and can ultimately lead to a system voltage collapse. Significant research have been focused on time-synchronized measurements of power systems which can be used to frequently determine the state of a power system and can lead to a more robust protection, control and operation performance. This thesis discusses the applicability of two voltage stability synchrophasor-based indices from …

Transient Small Wind Turbine Tower Structural Analysis With Coupled Rotor Dynamic Interaction, George R. Katsanis

Master's Theses

Structural dynamics is at the center of wind turbine tower design - excessive vibrations can be caused by a wide range of environmental and mechanical sources and can lead to reduced component life due to fatigue, noise, and impaired public perception of system integrity. Furthermore, periodic turbulent wind conditions can cause system resonance resulting in significantly increased structural loads. Structural vibration issues may become exacerbated in small wind applications where the analytical and experimental resources for system verification and optimization are scarce. This study combines several structural analysis techniques and packages them into a novel and integrated form that can …

Modeling And Analysis Of A Dynamic Voltage Regulator, Timothy David Haskell

Master's Theses

Increased government funding and incentives in recent years has led to an increase in the number of grid-tied renewable energy sources as their economic benefits become more renowned. Unfortunately, the outputs of these renewable resources are often highly variable, resulting in undesirable voltage disruptions that are harmful to sensitive loads. In addition to the energy variability of renewable energy sources, random voltage sags, swells and disruptions are already a major issue in power systems. Recent advances in power electronic devices have provided a platform for new solutions to the voltage support problem in power systems. One promising solution is the …

Modeling And Analysis Of A Pv Grid-Tied Smart Inverter's Support Functions, Benjamin Anders Johnson

Master's Theses

The general trends in the past decade of increasing solar cell efficiency, decreasing PV system costs, increasing government incentive programs, and several other factors have all combined synergistically to reduce the barriers of entry for PV systems to enter the market and expand their contribution to the global energy portfolio. The shortcomings of current inverter functions which link PV systems to the utility network are becoming transparent as PV penetration levels continue to increase. The solution this thesis proposes is an approach to control the inverters real and reactive power output to help eliminate the problems associated with PV systems …

Modeling The Zimmer Fitmore And Ml Taper Implantation, Tyler Kazuo Franklin

Master's Theses

With more young adults requiring total hip

arthroplasties the need for bone saving implants becomes

more important. The Zimmer Fitmore is a new bone saving

implant that utilizes an implantation technique that

reduces the damage to the muscle tissue allowing for

patients to have a short recovery time as well as a new

design that allows it to rest on the medial cortex. There

has been anecdotal evidence that this device leads to early

revision within six months of implantation due to failures

occurring in the medial cortex. The main goal of this

study was to computationally model the Zimmer …

An Experimental Investigation Of The Stol Performance Of Cal Poly's Amelia In The Nfac, Jonathan Andrew Lichtwardt

Master's Theses

Results from Cal Poly's recent wind tunnel test, during the Winter of 2011-2012, in the 40- by 80-foot test section at the National Full-Scale Aerodynamics Complex (NFAC) at NASA Ames Research Center are presented. AMELIA, the Advanced Model for Extreme Lift and Improved Aeroacoustics, is the first full-span, cruise efficient, short take-off and landing (CESTOL) model incorporating leading- and trailing-edge blowing wing circulation control and over-the-wing mounted turbine propulsion simulators (TPS) to date. Testing of the 10 foot span model proved successful and was the result of a 5 year NASA Fundamental Aeronautics Program Research Announcement. The test generated extensive …

Enabling Rapid Conceptual Design Using Geometry-Based Multi-Fidelity Models In Vsp, Joel Brian Belben

Master's Theses

The purpose of this work is to help bridge the gap between aircraft conceptual design and analysis. Much work is needed, but distilling essential characteristics from a design and collecting them in an easily accessible format that is amenable to use by inexpensive analysis tools is a significant contribution to this goal. Toward that end, four types of reduced-fidelity or degenerate geometric representations have been defined and implemented in VSP, a parametric geometry modeler. The four types are degenerate surface, degenerate plate, degenerate stick, and degenerate point, corresponding to three-, two-, one-, and zero- dimensional representations of underlying geometry, respectively. …

Novel Approach To Junctional Bleeding: Tourniquet Device Proposal For Battlefield Hemorrhage Control, Kyle W. Cabaniss

Master's Theses

This study investigated possible solutions to the current wartime problem of junctional hemorrhaging, or massive traumatic hemorrhaging in non-tourinquetable areas such as the neck, groin, or armpit. Junctional hemorrhaging has been identified as a major contributor to potentially survivable deaths seen on the battlefield today and therefore is a priority for the U.S. armed and coalition forces (Kragh et al., 2011a; Bozeman, 2011). Common tourniquets today are standard issue and carried by soldiers in the military, but are limited to distal extremity trauma. As the battlefield has changes however, trauma has transformed from commonly seen gunshot wounds to more extreme …

A Gravity Gradient, Momentum-Biased Attitude Control System For A Cubesat, Ryan J. Sellers

Master's Theses

ExoCube is the latest National Science Foundation (NSF) funded space weather CubeSat and is a collaboration between PolySat, Scientific Solutions Inc. (SSI), the University of Wisconsin, NASA Goddard and SRI International. The 3U will carry a mass spectrometer sensor suite, EXOS, in to low earth orbit (LEO) to measure neutral and ionized particles in the exosphere and thermosphere. Measurements of neutral and ion particles are directly impacted by the angle at which they enter EXOS and which leads to pointing requirements. A combination of a gravity gradient system with a momentum bias wheel is proposed to meet pointing requirements while …

Ad-Hoc Regional Coverage Constellations Of Cubesats Using Secondary Launches, Guy G. Zohar

Master's Theses

As development of CubeSat based architectures increase, methods of deploying constellations of CubeSats are required to increase functionality of future systems. Given their low cost and quickly increasing launch opportunities, large numbers of CubeSats can easily be developed and deployed in orbit. However, as secondary payloads, CubeSats are severely limited in their options for deployment into appropriate constellation geometries.

This thesis examines the current methods for deploying cubes and proposes new and efficient geometries using secondary launch opportunities. Due to the current deployment hardware architecture, only the use of different launch opportunities, deployment direction, and deployment timing for individual cubes …

Axisymmetric Air Augmented Methanol/Gox Rocket Mixing Duct Experimental Thrust Study, Kyle Jacob Johnson

Master's Theses

A hot-flow axisymmetric Air Augmented Rocket (AAR) test apparatus was constructed to test various mixing duct configurations at static conditions. Primary flow for the AAR was provided through a liquid methanol-gaseous oxygen bipropellant rocket. Experimental thrust measurements were recorded and propellant mass flow rates and chamber conditions were calculated using an iterative solver dependant on recorded propellant line stagnation pressures. Primary rocket flow produced thrust ranging from 14 to 17.9lbf. Primary mass flow rate through testing ranged from 0.071 to 0.085lbm/s with calculated chamber pressures between 298-362psia. Calculated primary flow velocity ranged from 6,600ft/s to 8,000ft/s depending on propellant pressure …

Effects Of Ovariectomy And Anatomical Location On Osteonal Encroachment In Adult Cortical Ovine Bone, Paige Brell Ryan

Master's Theses

The purpose of this study is to further quantify adult ovine ovariectomized bone for new remodeling characteristics to obtain a better understanding of how remodeling is occurring and the effectiveness of this animal model for the study of postmenopausal osteoporosis. Postmenopausal osteoporosis is a major health concern and animal models to test new treatment options are needed. The ovine model is a good option because the ewes undergo Haversian remodeling, are a large sized animal, and have a similar hormone profile to humans. Ewes, however, do not undergo a natural menopause, so an ovariectomy surgery was conducted in the sheep …

Modeling Flood Reduction Scenarios For A Small Coastal Community, Evan J. Perez

Master's Theses

The Arroyo Grande Creek Watershed, an approximately 170 mi² watershed located on the central coast of California, drains to the Pacific Ocean via the Arroyo Grande Creek that passes through several coastal cities including the community of Oceano. At the mouth of the Creek is the Arroyo Grande Lagoon, which is connected to another lagoon known as the Oceano Lagoon, by a tidal flap-gate whose hydraulics is a function of water levels in the two lagoons. Historically the Oceano Lagoon has played a part in floods that have occurred in the community of Oceano. The most recent flooding occurred …

System Identification Of A Bridge-Type Building Structure, Pablo D. Ramos Jr.

Master's Theses

The Bridge House is a steel building structure located in Poly Canyon, a rural area inside the campus of California Polytechnic State University, San Luis Obispo. The Bridge House is a one story steel structure supported on 4 concrete piers with a lateral force resisting system (LFRS) composed of ordinary moment frames in the N-S direction and braced frames in the E-W direction and vertically supported by a pair of trusses. The dynamic response of the Bridge House was investigated by means of system identification through ambient and forced vibration testing. Interesting findings such as diaphragm flexibility, foundation flexibility and …

Design And Performance Of Circulation Control Geometries, Rory Martin Golden

Master's Theses

With the pursuit of more advanced and environmentally-friendly technologies of today’s society, the airline industry has been pushed further to investigate solutions that will reduce airport noise and congestion, cut down on emissions, and improve the overall performance of aircraft. These items directly influence airport size (runway length), flight patterns in the community surrounding the airport, cruise speed, and many other aircraft design considerations which are setting the requirements for next generation aircraft. Leading the research in this movement is NASA, which has set specific goals for the next generation regional airliners and has categorized the designs that meet the …

Dc, Rf, And Thermal Characterization Of High Electric Field Induced Degradation Mechanisms In Gan-On-Si High Electron Mobility Transistors, Matthew Anthony Bloom

Master's Theses

Gallium Nitride (GaN) high electron mobility transistors (HEMTs) are becoming increasingly popular in power amplifier systems as an alternative to bulkier vacuum tube technologies. GaN offers advantages over other III-V semiconductor heterostructures such as a large bandgap energy, a low dielectric constant, and a high critical breakdown field. The aforementioned qualities make GaN a prime candidate for high-power and radiation-hardened applications using a smaller form-factor. Several different types of semiconductor substrates have been considered for their thermal properties and cost-effectiveness, and Silicon (Si) has been of increasing interest due to a balance between both factors.

In this thesis, the DC, …

Hydrologic Modeling Of The San Joaquin Valley Watershed For Purposes Of Nitrate Analysis, Stephen Carl Clayton

Master's Theses

The San Joaquin Valley is regarded as one of the most productive agricultural regions in the world. This extensive agriculture has, however, caused extensive pollution of both ground water and surface water. This thesis develops a hydrologic model of the surface and ground waters of the San Joaquin Valley. Such modeling is useful in the development and implementation of water quality regulations such as Total Maximum Daily Loads (TMDLs). A properly validated watershed simulation model can supplement data collection and can account for watershed characteristics including topography, soils, climate, land cover, anthropogenic activities, as well as simulate watershed responses including …

Rfid Technology Selection And Economic Justification For Healthcare Asset Tracking, Tyler Robert Peabody, Tali Freed

Master's Theses

Although Radio Frequency Identification (RFID) and Real-Time Location System (RTLS) technologies for inventory tracking have been growing in popularity, the healthcare industry has been reluctant to adopt these technologies. One of the primary reasons for this lack of enthusiasm has been the risk associated with electromagnetic interference between RFID/RTLS systems and medical equipment functionality. The other reason has been the substantial cost and complexity of implementing RFID/RTLS in healthcare organizations. In this study, we show that there are several ways to safely install RFID/RTLS systems to improve the inventory management processes of hospitals and clinics. We then analyze the inventory …

Cloth Filter For Disaster Relief Water Treatment, Shasta Le'ja Billings

Master's Theses

Relief organizations and governments strive to provide safe drinking water to natural disaster survivors as quickly as possible. However, drinking water is typically provided either as bottled water or via mobile water treatment equipment, both of which can be difficult or expensive to transport rapidly into disaster zones. An alternative is the waterbag point-of-use treatment device developed at Cal Poly that allows survivors to produce safe drinking water from contaminated local sources. The waterbag is a 10-L bladder designed for use with Procter & Gamble Purifier of Water (PŪR^®) sachets, which contain coagulant and chlorine compounds. Following treatment …

Bacterial Growth On Metal And Non-Metal Surfaces In A Static Bioreactor, Rolan Yuk Loong Liong

Master's Theses

Research was conducted to observe bacterial growth on the surface of metals in a static bioreactor. Metal and non-metal samples were subjected to bacterial exposure (1 day and 9 days). The metal samples were surface treated prior to bacterial exposure. The microstructures of the surface treated samples were analyzed by optical microscopy. After exposure, the microstructures of the samples were analyzed by scanning electron microscopy (SEM). The analysis suggested that microbial attachment on the surface was related to the underlying microstructure of steel. The preferential attachment of microbes could potentially be influenced by cathodic and anodic regions created by the …

Material Characterization Of Ultra-High Performance Fiber Reinforced Concrete At Elevated Temperatures, Richard T. Way

Master's Theses

With the recent development of Ultra High Performance Fiber Reinforced Concrete (UHPFRC), there has been limited investigation into the mechanical and material properties of this composite at elevated temperatures. At elevated temperatures concrete is shown to undergo several material changes which affect the residual mechanical properties. Additionally, fast heating rates are known to cause a phenomenon called explosive spalling. This research investigates the effect of high temperature on the residual mechanical properties and chemical degradation of two types of UHPFRC. This was accomplished by casting and testing two different UHPFRC mixes and exposing them to elevated temperatures at two rates …

Material Characterization And The Effects Of Moisture And Drying On Injection Molded Torlon 5030, Michael R. Di Re

Master's Theses

The effects of water absorption and drying were studied on injection molded Torlon 5030, a high performance thermoplastic fabricated by Solvay Specialty Polymers. Torlon 5030 contains 30% by weight glass fibers in a polyamide-imide base resin. The objective behind this work was to test and better define relevant properties for industrial applications using this material. While the material design guide offers information on many mechanical properties including tensile, fatigue, and creep data; there is little to no publicly published data on the effects of water absorption and any subsequent drying of Torlon 5030. Blistering was also studied. With exposure to …

Microkinetic Modeling And Analysis Of Ethanol Partial Oxidation And Reforming Reaction Pathways On Platinum At Short Contact Times, Maura A. Koehle

Master's Theses

No abstract provided.

Automated Point-Of-Care Image Processing Methodology For The Diagnosis Of Malaria, Michael B. Jorgensen

Master's Theses

Malaria has profoundly influenced human history for over four thousand years and despite numerous attempts at eradication, the prevention, diagnosis, and treatment of malaria have been largely ineffective. More than five hundred million people are affected by malaria every year resulting in over one million deaths. Drug resistance development by the parasite has diminished the effectiveness of numerous treatment options due, in part, to overtreatment of negative patients based on insufficient clinical algorithms and diagnostic methods. The goal of this research was to develop an image analysis algorithm to diagnose malaria with a high degree of sensitivity and specificity in …

Multiplatform Analysis Seismic Evaluation Of A Non-Seismically Detailed Nonlinear Rc Structure Retrofitted With Magneto-Rheological Dampers, Eric R. Lovejoy

Master's Theses

In prior research, the MR damper's dynamic characteristics are typically modeled in the MATLAB/Simulink environment. Creating a structural model with nonlinear material properties, however, may be challenging in the MATLAB/Simulink environment without approximating the material behavior and neglecting effects such as P-∆ or panel zone behavior. More behaviorally accurate models of these structures can be produced using nonlinear finite element analysis tools such as Abaqus, OpenSees or ZuesNL. These analysis tools, however, are not traditionally used to model the complex nonlinear and controllable behavior of MR dampers, nor their associated control algorithms. One solution is to facilitate communication between these …

Investigation Of Astm E 238 Bearing Pin Properties For Various Aerospace Alloys, Trevor J. Lee

Master's Theses

Aircraft are often designed with numbers determined by testing in a lab, rather than by repeatedly building prototypes. These lab tests conform to testing specifications so that the numbers can be compared between manufacturers, suppliers, and lab technicians. One such specification is ASTM specification E238 – 84(08), and it is used to determine important properties of a bearing pin joint like hinges, bolt holes, and rivet joints. The properties determined from this fastener-through-plate method are bearing strength, bearing yield strength, and bearing stiffness.

Adhering to the methods outlined in ASTM E238, a study was performed, looking at the effects that …

The Effect Of Sensor Mass, Sensor Location, And Delamination Location Of Different Composite Structures Under Dynamic Loading, Albert Darien Liu

Master's Theses

This study investigated the effect of sensor mass, sensor location, and delamination location of different composite structures under dynamic loading. The study pertains to research of the use of accelerometers and dynamic response as a cost-effective and reliable method of structural health monitoring in composite structures. The composite structures in this research included carbon fiber plates, carbon fiber-foam sandwich panels, and carbon-fiber honeycomb sandwich panels. The composite structures were manufactured with the use of a Tetrahedron MTP-8 heat press. All work was conducted in the Cal Poly Aerospace Structures/Composites Laboratory. Initial delaminations were placed at several locations along the specimen, …

A Tunable Electromagnetic Band-Gap Microstrip Filter, Greg A. Lancaster

Master's Theses

In high frequency design, harmonic suppression is a persistent struggle. Non-linear devices such as switches and amplifiers produce unwanted harmonics which may interfere with other frequency bands. Filtering is a widely accepted solution, however there are various shortcomings involved. Suppressing multiple harmonics, if desired, with traditional lumped element and distributed component band-stop filters requires using multiple filters. These topologies are not easily made tunable either. A new filter topology is investigated called Electromagnetic Band-Gap (EBG) structures.

EBG structures have recently gained the interest of microwave designers due to their periodic nature which prohibits the propagation of certain frequency bands. EBG …

Condition-Dependent Risk Assessment Of Large-Scale Grid-Tied Photovoltaic Power Systems, Sherwin Li

Master's Theses

This thesis reviews the methods for evaluating the reliability of large PV systems and techniques for quantifying the impacts of PV interconnection on distribution system reliability. In addition, a comparative study is performed to evaluate the seasonal condition-dependent risk performance of central-inverter and string-inverter grid-tied PV power systems. Major contributions include: 1) risk analysis of seasonal impacts for string and centralized PV systems. Seasonal sensitivities of PV system risks to system structures, temperature variation, solar insolation, and capacitor equivalent series resistance are analyzed; and 2) the incorporation of the effect of operational conditions and the aging failure model into the …