Engineering Commons^™

Development Of Microdialysis Probes In Series Approach Toward Eliminating Microdialysis Sampling Calibration: Miniaturization Into A Pdms Microfluidic Device, Randy Espinal Cabrera

Graduate Theses and Dissertations

A new microdialysis sampling method and microfluidic device were developed in vitro. The method consisted of using up to four microdialysis sampling probes connected in series to evaluate the relative recovery (RR) of different model solutes methyl orange, fluorescein isothiocyanate (FITC)-dextran average mol. wt. 4,000 (FITC-4), FITC-10, FITC-20, and FITC-40. Different flow rates (0.8, 1.0, and 1.5 µL/min) were used to compare experimentally observed relative recoveries with theoretical estimations. With increasing the number of probes in series, the relative recovery increases and ~100% (99.7% ± 0.9%) relative recovery for methyl orange was obtained. For larger molecules such as fluorescein isothiocyanate …

A Multi-Objective Affinity-Based Savings Algorithm For Improving Processes In Centralized Warehousing Operations, Mckenlee M. Coco

Graduate Theses and Dissertations

Traditional approaches to improving material management processes in warehousing operations tend to focus on one of three major areas: facility design, order picking and sorting, and order batching. In an effort to improve total system savings, a new affinity function is developed and applied to batching logic to create a multi-objective problem. The proposed multi-objective function incorporates user input to increase adaptability to changing demand and flexibility to changing requirements. Computational experience shows the new function leads to solutions that deviate no more than 25% from the most efficient distance based picking route by the same batching logic, while creating …

Developing A Hil-Based Software Platform For Testing Electric And Hybrid Vehicle Powertrains, Daniel Schwartz

Graduate Theses and Dissertations

The objective of this thesis is to present a dynamometer test stand with hardware in the loop (HIL) testing capabilities for the evaluation of electric and hybrid vehicle powertrains under realistic driving conditions. The traction inverter and dc/dc converter are two crucial subsystems of the powertrain and new prototypes require significant validation before implementing into production vehicles. As fundamental technologies such as power modules, thermal management systems, and passive components improve; the performance improvements to the overall system must be demonstrated. The plug and play nature of the testbed makes it ideal for making direct comparisons of design iterations under …

Design, Fabrication, And Characterization Of All-Inorganic Quantum Dot Light Emitting Diodes, Ramesh Vasan

Graduate Theses and Dissertations

Quantum dot light emitting diodes are investigated as a replacement to the existing organic light emitting diodes that are commonly used for thin film lighting and display applications. In this, all-inorganic quantum dot light emitting diodes with inorganic quantum dot emissive layer and inorganic charge transport layers are designed, fabricated, and characterized. Inorganic materials are more environmentally stable and can handle higher current densities than organic materials. The device consists of CdSe/ZnS alloyed core/shell quantum dots as the emissive layer and metal oxide charge transport layer. The charge transport in these devices is found to occur through resonant energy transfer …

Phase Transitions In Monochalcogenide Monolayers, Mehrshad Mehboudi

Graduate Theses and Dissertations

Since discovery of graphene in 2004 as a truly one-atom-thick material with extraordinary mechanical and electronic properties, researchers successfully predicted and synthesized many other two-dimensional materials such as transition metal dichalcogenides (TMDCs) and monochalcogenide monolayers (MMs). Graphene has a non-degenerate structural ground state that is key to its stability at room temperature. However, group IV monochalcogenides such as monolayers of SnSe, and GeSe have a fourfold degenerate ground state. This degeneracy in ground state can lead to structural instability, disorder, and phase transition in finite temperature. The energy that is required to overcome from one degenerate ground state to another …

Characterization Of Bacteriorhodopsin And Halorhodopsin Reconstituted In Lipid Bilayer Membranes, Joel Domkam Kamwa

Graduate Theses and Dissertations

Motivated to produce electricity with photon activated ion pumps, the main purpose of this work was to characterize the photosynthetic membrane proteins bacteriorhodopsin (proton pump) and halorhodopsin (chloride pump). The proteins were re-suspended in lipid bilayers. For this work, an experimental set-up was built which included: chambers for lipid bilayer formation and characterization, lasers for ion pump activation, and an AxoPatch electrophysiology system for small photocurrent measurement. Lipid bilayer membranes were formed using mostly folding method: folding two monolayers together. The membranes were characterized by their resistance, capacitance, and generated photocurrent. Photocurrent was generated upon illumination of lipid-protein membranes with …

Essays On Applications Of Transportation Network Design And Optimization, Amirali Ghaharikermani

Graduate Theses and Dissertations

In this dissertation, we address different transportation problems. The three main outcomes are: designing a battery swap station network, studying gaps in Empty Container Management literature, designing a model with similar characteristics to the vehicle routing problem as well as implementation scenario for it to be applied for a real-world case.

For the designed battery swap station, a model is developed for customer demand satisfaction that permits construction of different types of BSS in the planning network. Our solution methodology is a Tabu Search algorithm combined with a dynamic programming initialization. Numerous tests showed that the proposed TS approach provides …

Demonstrating Set-Based Design Techniques- A Uav Case Study, Colin Small

Graduate Theses and Dissertations

The Department of Defense (DoD) and Engineered Resilient Systems (ERS) community seek to improve decision making in the Analysis of Alternatives (AoA) process by incorporating resilience and leveraging the capabilities of model-based engineering (MBE) early in the design process. Traditional tradespace exploration utilizing Point-Based Design (PBD) often converges quickly on a solution with subsequent engineering changes to modify the design. However, this process can lead to a suboptimal solution if an incorrect initial solution is chosen. Enabled by MBE, Set-Based Design (SBD) considers sets of all possible solutions and enables down-selecting possibilities to converge on a final solution. Using a …

Investigation Of Nanomaterial Based Photovoltaic Panel Packaging Materials, Xingeng Yang

Graduate Theses and Dissertations

In this research, nanomaterial-based packaging materials for photovoltaic (PV) panels are investigated. A hydrophobic/anti-reflective surface coating which not only repels water from the top glass of a PV panel but at the same time reduces its light reflectance is investigated. COMSOL simulation results indicate that taller ellipsoid rod (aspect ratio = 5) reflects less light than shorter rod (aspect ratio = 0.5) in the desired spectrum for solar energy harvest from 400nm-700nm. The addition of a polymer layer on these ellipsoid rods broadens the light incident angle from 23° to 34°, from which light can be efficiently absorbed. Based on …

Low Latency Intrusion Detection In Smart Grids, Israel Zairi Akingeneye

Graduate Theses and Dissertations

The transformation of traditional power grids into smart grids has seen more new technologies such as communication networks and smart meters (sensors) being integrated into the physical infrastructure of the power grids. However, these technologies pose new vulnerabilities to the cybersecurity of power grids as malicious attacks can be launched by adversaries to attack the smart meters and modify the measurement data collected by these meters. If not timely detected and removed, these attacks may lead to inaccurate system state estimation, which is critical to the system operators for control decisions such as economic dispatch and other related functions.

This …

Application Of Modular Multilevel Converters (Mmc) Using Phase-Shifted Pwm And Selective Harmonic Elimination In Distribution Systems, Thouhidul Islam

Graduate Theses and Dissertations

Reducing the size and weight of a power electric system is a prodigious challenge to researchers as the development of the latest technologies emerge in the field of electrical engineering. A similar urge is there to develop a light-weight mobile power substation (MPS) to use in the electric power distribution systems during emergency conditions. This thesis proposes a power electronics based solution using the modular multilevel converter (MMC) topology to design the MPS system. The market-available power semiconductor devices are analyzed and suitable devices are selected to design the system. The phase-shifted pulse width modulation (PS-PWM) and selective harmonic elimination …

Convergent Set-Based Design In Integrated Analysis Of Alternatives: Designing Engineered Resilient Systems, Zephan Wright Wade

Graduate Theses and Dissertations

This thesis presents a comprehensive package for understanding and expanding set-based design quantification through the definition and demonstration of Convergent set-based design (SBD). Convergent SBD is a technique developed for the Engineered Resilient Systems program sponsored by the Department of Defense. Convergent SBD contributes a repeatable methodology with the goal of mathematically eliminating inefficient sets. The study of Convergent SBD led to the development of dominance identification criteria equations using comparison of statistical means. The demonstration of Convergent SBD also illustrates the effect of mission resilience in the tradespace and the impact mission resilience has on preference. Finally, Convergent SBD …

Fabrication And Characterization Of Graphene Based 2d Materials For Supercapacitors, Anishkumar Manoharan

Graduate Theses and Dissertations

Supercapacitors have attracted a lot attention due to their efficient energy storage. In comparison to batteries, supercapacitors have high capacitance, energy, and power densities per unit mass than conventional capacitors. Carbon based materials are most promising in supercapacitor application due to their outstanding physical and electrochemical behavior. In this work, a facile method to synthesize a nanocomposite electrode consisting of annealed carbon from carbon ink and MoS2 was demonstrated. Effects of various aqueous and solid electrolytes were studied. It was found that the nanocomposite electrode with 10% MoS2 and 1M Na2SO4 as the aqueous electrolyte tested using the three electrode …

Gating Methods For High-Voltage Silicon Carbide Power Mosfets, Audrey Dearien

Graduate Theses and Dissertations

The objective of this thesis is to assess the challenges associated with driving Silicon Carbide (SiC) power devices, and to compare the potential gate drive methods for these devices which address those challenges. SiC power devices present many benefits that make them suitable for next generation automotive, power utility grid, and energy management applications. High efficiency, increased power density, and reliability at high-temperatures are some of the main benefits of SiC technology. However, the many challenges associated with these devices have prevented their adoption into industry applications. The argument is made in this thesis that the gate driver is a …

Exploring Energy, Comfort, And Building Health Impacts Of Deep Setback And Normal Occupancy Smart Thermostat Implementation, Zachary Ethan Alderman

Graduate Theses and Dissertations

As smart thermostat adoption rates continue to increase, it becomes worthwhile to explore what unanticipated outcomes may result in their use. Specific attention was paid to smart thermostat impacts to deep setback and normal occupancy states in a variety of conditions while complying with the ventilation and temperature requirements of ASHRAE 90.2-2013. Custom weather models and occupancy schedules were generated to efficiently explore a combination of weather conditions, building constructions, and occupancy states. The custom modeling approach was combined with previous experimental data within the Openstudio graphics interface to the EnergyPlus building modeling engine. Results indicate smart thermostats add the …

On The Fatigue Of Headed Shear Studs In Steel-Concrete Composite Bridge Girders, Brianna Laurene Ovuoba

Graduate Theses and Dissertations

Shear connectors are commonly used in steel bridges to join the concrete deck and steel superstructure, providing a mechanism for shear transfer across the steel-concrete interface. The most common shear connector is the headed shear stud. In the current AASHTO LRFD Bridge Specifications on composite design, shear stud fatigue often governs over static strength, and a large number of shear connectors often result. This dissertation investigates headed shear stud fatigue capacities and demands, and provides insight into conservancies in existing design specifications through examination of existing high-traffic bridge performance.

To investigate stud capacity, a total of six high-cycle fatigue tests …

Development Of An Internal Camera-Based Volume Determination System For Triaxial Testing, Sean Elliott Salazar

Graduate Theses and Dissertations

Accurate measurement of axial, radial, and volumetric strain parameters are critical to the understanding of phase relationships and the constitutive behavior for saturated and unsaturated soils. The use of photographic monitoring techniques for laboratory-based measurement of these parameters have become common. A novel technique that utilized camera instrumentation located within the triaxial testing cell was developed and validated. By placing the instrumentation inside of the cell, instead of the instrumentation being located outside of the cell, the technique eliminated cumbersome corrections required to account for optical distortions due to 1) the refraction of light at the confining fluid-cell wall-atmosphere interfaces, …

Cost-Savings Of Implementing Site-Specific Ground Motion Response Analysis In Design Of Mississippi Embayment Bridges, Ethan Ryan Benton Baker

Graduate Theses and Dissertations

Deep dynamic site characterization and a site-specific ground motion response analysis (SSGMRA) were conducted for a bridge site in Monette, Arkansas. The SSGMRA indicated the design acceleration response spectrum determined using the American Association of State Highway and Transportation Officials (AASHTO) general seismic procedure could be reduced by 1/3 for the short period range due to attenuation of the short-period ground motions. The steel girder pile-bent bridge, originally designed using the AASHTO general seismic design procedure, was redesigned using the updated seismic demands estimated from SSGMRA. A cost-savings analysis was then conducted to determine the potential savings associated with conducting …

An Evaluation Of Borehole Hydraulic Conductivity Equations And Field Determined Soil Water Characteristic Curves, Johnathan Dale Blanchard

Graduate Theses and Dissertations

The methods utilized to determine the hydraulic conductivity of compacted clay liners (CCLs) are of importance for safe guarding the environment from landfill leachate. Therefore, the methods utilized in the analysis of the Two Stage Borehole (TSB) test, as described in the ASTM D6391-11 (Method A, B, and C) standard, were evaluated. Data from hydraulic conductivity tests, as performed on three test pads, were utilized to review the ASTM D6391-11 equations. Additionally, two test pads were instrumented with volumetric water content and soil water matric potential sensors to facilitate the determination of field-obtained soil water characteristic curves (SWCCs) and hydraulic …

Automated Pin-Dot Marking Effects On A709-Gr50 Steel Plate Fatigue Capacity, Michael Andrew Noernberg

Graduate Theses and Dissertations

During fabrication of multi-piece steel bridge assemblies, markings are often made on the steel surface to identify/track individual pieces or to provide reference for fabrication layout or later erection. Automated marking methods such as computer numerically controlled (CNC) pin-dot marking offer fabrication efficiencies; however, for marked steel sections subjected to frequent or repeated loading (i.e. bridge girders) many code specifications require experimental testing to verify any marking effects on fatigue capacity. In this study, the effects of automated pin-dot markings on the fatigue capacity of A709-Gr50 bridge steel are experimentally investigated from 13 specimens considering 2 marking frequencies (corresponding to …

Evaluation Of Water Resources And Hydraulic Influences In The Restoration Of The Western Part Of The Mesopotamian Marshlands, Ali Kareem Al-Quraishi

Graduate Theses and Dissertations

The purpose of this study is to assess the water resources and water conveyance system of the western part of the Mesopotamian marshes (Al-Hammar marsh) as well as develop a water conveyance system to distribute water throughout the western Al-Hammar marsh. These processes are significant to identify the current restoration problems and help to create restoration strategies for the marsh. Also, proper management strategy to the Al-Hammar marsh is necessary to preserve the marsh ecosystem, irrigate lands, and provide domestic necessities in the villages.

The overall project is divided into three main chapters which address the current ecological and hydrological …

Dem Study Of A Single Stone Column In A Clayey Stratum, Anibal Enrique Santos

Graduate Theses and Dissertations

Aggregate piers are an alternative ground improvement technique used for improving the bearing capacity and reducing the total and differential settlement of foundations supported on compressible soils. The piers are composed of a series of vibrationally compacted aggregate lifts from a desired depth up to the finished foundation level. The shear strength of the coarse-grained material comprising an aggregate pier is defined by its internal friction angle. There are several factors affecting the friction angle of the granular material that include: confining stress, particle shape, relative density and particle distribution (gradation). These factors are not directly considered in the design …

3d Printed Pcu/Uhmwpe Polymeric Blends For Artificial Knee Meniscus, Raissa Araujo Borges

Graduate Theses and Dissertations

3D printing was used to fabricate porous artificial knee meniscus material from biocompatible polymeric blends of polycarbonate-urethane (PCU) and ultra-high-molecular-weight polyethylene (UHMWPE) to enable “weep” lubrication that mimics the native meniscus. 3D printed and molded pure PCU, as well as molded PCU and UHMWPE, were used for comparison. Preliminary printing was done to evaluate the impact of process parameters on the results. The samples were subject to a variety of rotational oscillating friction and wear tests under simulated body fluid and loading conditions to replicate the natural motion of the knee. Results show that 3D printed PCU samples yielded a …

Systematic Review For Water Network Failure Models And Cases, Yufei Gao

Graduate Theses and Dissertations

As estimated in the American Society of Civil Engineers 2017 report, in the United States, there are approximately 240,000 water main pipe breaks each year. To help estimate pipe breaks and maintenance frequency, a number of physically-based and statistically-based water main failure prediction models have been developed in the last 30 years. Precious review papers focused more on the evolution of failure models rather than modeling results. However, the modeling results of different models applied in case studies are worth reviewing as well.

In this review, we focus on research papers after Year 2008 and collect latest cases without repetition. …

Investigating Fate Of Silver Nanoparticles In Wastewater Biofilms, Connie Marie Walden

Graduate Theses and Dissertations

As industrial advances make everyday life easier for human kind, the processes by which we need to maintain sanitary conditions for both water and wastewater treatment will become increasingly complex. Innovations in food packaging and textile design incorporate engineered nanoparticles (ENPs) to increase antimicrobial properties of clothing, maintain product color, and keep food in packaging from spoilage. For most products, ENPs released will enter the sanitary sewer system, and ultimately wastewater treatment plants. Biofilms grow universally on surfaces where a protective layer of extracellular polymeric substances (EPS) shields attached cells from stressors. In wastewater treatment, complex biofilms are utilized as …

Airport Security Investment Model, Joshua Daniel Bolton

Graduate Theses and Dissertations

In an increasingly mobile and diverse world, it is difficult to quantify the risk, or danger, associated with traveling. Airports have suffered greatly for being unable to define potential risks and protect against them. Intelligent adversary risk is a complicated high-level issue for many airports. Airports are targeted because of the large amount of people in a confined space and the social, economic, and psychological impact of terrorist attacks on the American people. In the months following September 11th, 2001, the airline industry in the United States lost $1.1 billion in revenue. The American people stayed grounded, for fear of …

Development Of Pre-Stressed Retrofit Strategies For Mitigating Fatigue Cracking In Steel Waterway Lock Gate Components, Christine Michelle Lozano

Graduate Theses and Dissertations

Lock gates are an important part of the transportation infrastructure within the United States (US), having many economic, safety, and environmental benefits over rail and highway transportation systems. Unfortunately, many existing lock gates throughout the US have reached or exceeded their initial design life and require frequent repairs to remain in service. Unscheduled repairs often increase as gates age, having a local economic impact on freight transport which can create economic ripples throughout the nation. Fatigue and corrosion are key causes of unscheduled service interruptions, degrading lock gate components over time. Additionally, because lock gates are submerged during operation, crack …

Structural And Elastic Properties Of Degenerate Sno Monolayers At Finite Temperature, Afsana Sharmin

Graduate Theses and Dissertations

Chalcogen-based layered superconductors with a litharge structure such as FeS and FeSe mono-layers undergo structural and superconducting phase transitions that are tunable by doping. Representing another material platform with a litharge structure but without valence d-electrons, SnO monolayers also display a structural ground state with a degenerate rectangular unit cell at zero temperature and a charge-tunable energy barrier that leads to a thermally-controllable structural phase change. Doped SnO monolayers with rectangular degenerate unit cells give rise to two-dimensional multiferroicity. Their two-dimensional elastic energy landscape adopts a basic analytic expression that is employed to discuss this structural transition. The results contained …

Analyzing The Fundamental Aspects And Developing A Forecasting Model To Enhance The Student Admission And Enrollment System Of Msom Program, Sultanul Nahian Hasnat

Graduate Theses and Dissertations

A forecasting model, associated with predictive analysis, is an elementary requirement for academic leaders to plan course requirements. The M.S. in Operations Management (MSOM) program at the University of Arkansas desires to understand future student enrollment more accurately. The available literature shows that there is an absence of forecasting models based on quantitative, qualitative and predictive analysis. This study develops a combined forecasting model focusing on three admission stages. The research uses simple regression, Delphi analysis, Analysis of Variance (ANOVA), and classification tree system to develop the models. It predicts that 272, 173, and 136 new students will apply, matriculate …

Free-Space Measurements Of Dielectrics And Three-Dimensional Periodic Metamaterials, Clifford E. Kintner

Graduate Theses and Dissertations

This thesis presents the free-space measurements of a periodic metamaterial structure. The metamaterial unit cell consists of two dielectric sheets intersecting at 90 degrees. The dielectric is a polyetherimide-based material 0.001” thick. Each sheet has a copper capacitively-loaded loop (CLL) structure on the front and a cut-wire structure on the back. Foam material is used to support the unit cells. The unit cell repeats 40 times in the x-direction, 58 times in the y-direction and 5 times in the z-direction. The sample measures 12” × 12” × 1” in total. We use a free-space broadband system comprised of a pair …