Open Access. Powered by Scholars. Published by Universities.®

Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

Faculty Publications

Discipline
Institution
Keyword
Publication Year
File Type

Articles 2671 - 2700 of 3294

Full-Text Articles in Engineering

Synthesis And Characterization Of Mno2-Based Mixed Oxides As Supercapacitors, Hansung Kim, Branko N. Popov Jan 2003

Synthesis And Characterization Of Mno2-Based Mixed Oxides As Supercapacitors, Hansung Kim, Branko N. Popov

Faculty Publications

Mn/Pb and Mn/Ni mixed oxide were prepared at ambient temperature by reduction of KMnO4 with Mn, Pb, and Ni salts. This low-temperature approach provides amorphous structure of the active material. The specific capacitance of pure MnO2 was estimated to be 166 F/g and increased to 210 and 185 F/g for Mn/Ni and Mn/Pb oxides, respectively. The carbon loading was optimized at 20 wt %. Based on a single electrode, the Mn/Ni mixed oxide showed a high rate capability of 3.12 Wh/kg at constant power discharge of 1 kW/kg.

Go to article

Corrosion Protection Of Steel Using Nonanomalous Ni-Zn-P Coatings, Basker Veeraraghavan, Bala Haran, Swaminatha P. Kumaraguru, Branko N. Popov Jan 2003

Corrosion Protection Of Steel Using Nonanomalous Ni-Zn-P Coatings, Basker Veeraraghavan, Bala Haran, Swaminatha P. Kumaraguru, Branko N. Popov

Faculty Publications

A novel technique for obtaining nonanomalous Ni-Zn-P coatings with high Ni content (74 wt % as compared to 15-20 wt % in the conventional plating method) has been developed. These coatings show promise as a replacement for Cd in sacrificially protecting steel. Ni-Zn-P coatings were deposited using an electroless method from a solution containing NiSO4, complexing agent and ammonium chloride. Varying the concentration of ZnSO4 in the bath controls the final amount of Zn in the deposit. The Zn content in the coating was optimized based on the corrosion resistance of the final deposit. Coatings with 16.2 …

Go to article

Full Cell Mathematical Model Of A Mcfc, N. Subramanian, B. S. Haran, Ralph E. White, Branko N. Popov Jan 2003

Full Cell Mathematical Model Of A Mcfc, N. Subramanian, B. S. Haran, Ralph E. White, Branko N. Popov

Faculty Publications

A theoretical model for the molten carbonate fuel cell was developed based on the three-phase homogeneous approach. Using this model, the contribution of different cell components to losses in cell performance has been studied. In general, at low current densities, the electrolyte matrix contributed to the major fraction of potential losses. Mass transfer effects became important at high current densities and were more prominent at the cathode. Electrolyte conductivity and cathode exchange current density seemed to play a limiting role in determining cell performance. Using the model, the maximum power density from a single cell for different cell thicknesses was …

Go to article

Thermally Stable Gel Polymer Electrolytes, Min-Kyu Song, Young-Taek Kim, Yong Tae Kim, Byung Won Cho, Branko N. Popov, Hee-Woo Rhee Jan 2003

Thermally Stable Gel Polymer Electrolytes, Min-Kyu Song, Young-Taek Kim, Yong Tae Kim, Byung Won Cho, Branko N. Popov, Hee-Woo Rhee

Faculty Publications

To prepare miscible polyethylene glycol diacrylate/polyvinylidene fluoride (PEGDA/PVdF) blend gel polymer electrolytes, low molecular weight (M = 742) liquid PEGDA oligomer was mixed with PVdF-HFP dissolved in ethylene carbonate/dimethyl carbonate/LiPF6 liquid electrolytes, and then cured under ultraviolet irradiation. Room temperature conductivity of PEGDA/PVdF blend films was found to be comparable to that of PVdF-HFP gel polymer electrolytes, and they were electrochemically stable up to 4.6 V vs. Li/Li+. Scanning electron micrographs revealed that PEGDA/PVdF blend electrolytes have pore size intermediate between dense PEGDA and highly porous PVdF-HFP. It was confirmed by weight change measurement that liquid electrolyte …

Go to article

Development Of A Novel Electrochemical Method To Deposit High Corrosion Resistant Silicate Layers On Metal Substrates, Basker Veeraraghavan, Bala Haran, Dragan Slavkov, Swaminatha Prabhu, Branko N. Popov, Bob Heimann Jan 2003

Development Of A Novel Electrochemical Method To Deposit High Corrosion Resistant Silicate Layers On Metal Substrates, Basker Veeraraghavan, Bala Haran, Dragan Slavkov, Swaminatha Prabhu, Branko N. Popov, Bob Heimann

Faculty Publications

A novel method for electrodepositing silicates on metallic substrates from aqueous solutions has been developed. The technique is demonstrated by forming a passive film on galvanized steel. The silicate layer was deposited cathodically from a bath containing PQ Corporation N sodium silicate solution (3.22 weight ratio sodium silicate, 37.5% solution in water). A post-treatment drying process increased the Si content in the coating and improved the corrosion characteristics of the silicate layer. Deposition parameters like bath concentration and temperature have been optimized using corrosion characteristics and surface morphology of the final coating. Finally, stability studies show that the silicate coatings …

Go to article

Polyetheretherketone Membranes For Elevated Temperature Pemfcs, Balasubramanian Lakshmanan, Wayne Huang, David Olmeijer, John W. Weidner Jan 2003

Polyetheretherketone Membranes For Elevated Temperature Pemfcs, Balasubramanian Lakshmanan, Wayne Huang, David Olmeijer, John W. Weidner

Faculty Publications

Membrane electrode assemblies ~MEAs! made from polyetheretherketone ~PEEK! showed excellent fuel cell performance and thermal stability in the presence of substantial CO at elevated temperatures ~i.e., 120°C! in proton exchange membrane fuel cells ~PEMFCs!. For example, the current from a MEA made from PEEK membrane at 0.6 V and 120°C was 0.50 A/cm2 when run on pure hydrogen and 0.45 A/cm2 when run on reformate ~50% H2 , 1300 ppm CO, and balance N2). The current density from a MEA made from Nafion at 0.6 V and 120°C was 0.61 A/cm2 when run on pure hydrogen. The main difference between …

Go to article

Identity Management, Duncan A. Buell, Ravi Sandhu Jan 2003

Identity Management, Duncan A. Buell, Ravi Sandhu

Faculty Publications

No abstract provided.

Go to article

The Sentient Web, Michael N. Huhns Jan 2003

The Sentient Web, Michael N. Huhns

Faculty Publications

In a startling revelation, a team of university scientists has reported that a network of computers has become conscious and sentient, and is beginning to assume control of online information system. In spite of the ominous tone typically chosen for dramatic effect, a sentient Web would be more helpful and much easier for people to use. An agent is an active, persistent software component that perceives, reasons, and acts, and whose actions include communication. Agents inherently take intentional actions based on sensory information and memories of past actions. All agents have necessary communication ability, but they do not necessarily possess …

Go to article

The Zen Of The Web, Jeff Heflin, Michael N. Huhns Jan 2003

The Zen Of The Web, Jeff Heflin, Michael N. Huhns

Faculty Publications

No abstract provided.

Go to article

Commitments Among Agents, Ashok U. Mallya, Michael N. Huhns Jan 2003

Commitments Among Agents, Ashok U. Mallya, Michael N. Huhns

Faculty Publications

Commitments are a powerful representation for modeling multiagent interactions. Previous approaches have considered the semantics of commitments and how to check compliance with them. However, these approaches do not capture some of the subtleties that arise in real-life applications such as e-commerce, in which contracts and institutions have implicit temporal references. In this column, we describe a rich representation for the temporal content of commitments that lets us capture realistic contracts and avoid ambiguities. Consequently, this approach lets us reason about whether, and at what point, a commitment is satisfied or breached, and whether it is or ever becomes unenforceable.

Go to article

Being And Acting Rational, Michael N. Huhns Jan 2003

Being And Acting Rational, Michael N. Huhns

Faculty Publications

Rationality alone is insufficient to specify agent design. Using economic theory, we can program agents to behave in ways that maximize their utility while responding to environmental changes. However, economic models for agents, although general in principle, are typically limited in practice because the value functions that are tractable essentially reduce an agent to acting selfishly. Building a stable social system from a collection of agents motivated by self-serving interests is difficult. Finally, understanding rationality and knowledge requires interdisciplinary results from artificial intelligence, distributed.

Go to article

Massive Deliberation, William H. Turkett Jr., John R. Rose, Michael N. Huhns Jan 2003

Massive Deliberation, William H. Turkett Jr., John R. Rose, Michael N. Huhns

Faculty Publications

Agents are proliferating on the Web, making it conceivable that their collective reasoning ability might someday be harnessed for robust decision-making. The hope is that massive deliberation power can soon help solve problems that require knowledge, reasoning, and intelligence. Until recently, working individually or in small groups, agents across the Web could barely communicate and could only reason under conditions of severely bounded rationality. Projects such as Agentcities showed that widespread heterogeneous agents could collaborate on specific predefined tasks and provide diverse agent-based services. When the tasks are dynamic, of long duration, and ill defined, however, success requires planning that …

Go to article

Theoretical Analysis For Obtaining Physical Properties Of Composite Electrodes, Parthasarathy M. Gomadam, John W. Weidner, Thomas A. Zawodzinski, Andrew P. Saab Jan 2003

Theoretical Analysis For Obtaining Physical Properties Of Composite Electrodes, Parthasarathy M. Gomadam, John W. Weidner, Thomas A. Zawodzinski, Andrew P. Saab

Faculty Publications

A theoretical analysis is presented that allows in situ measurements of the physical properties of a composite electrode, namely, the electronic conductivity, the ionic conductivity, the exchange-current density, and the double-layer capacitance. Use is made of the current-voltage responses of the composite electrode to dc and ac polarizations under three different experimental configurations. This analysis allows the physical properties to be obtained even when the various resistances in the composite (e.g., ionic, electronic, and charge-transfer) are of comparable values.

Go to article

Modeling Heat Conduction In Spiral Geometries, Parthasarathy M. Gomadam, Ralph E. White, John W. Weidner Jan 2003

Modeling Heat Conduction In Spiral Geometries, Parthasarathy M. Gomadam, Ralph E. White, John W. Weidner

Faculty Publications

A two-dimensional (2-D) energy balance (the 2D model) is reduced to a one-dimensioanl (1-D) energy balance (the 1D-radial-spiral model) by a coordinate transformation approach. The 1D-radial-spiral model, even though 1-D, captures both radial and spiral heat conductions over a wide range of design parameters. By comparing the temperature predictions of the 1D-radial-spiral model and the 2D model, parameter ranges were identified where spiral conduction was important and where the 1D-radial-spiral model held. The 1D-radial-spiral model provided a sixtyfold savings in computation time over the 2D model. When coupled to electrochemistry, the 2D model took approximately 20 h to simulate a …

Go to article

Analysis Of Molten Carbonate Fuel Cell Performance Using A Three-Phase Homogeneous Model, N. Subramanian, B. S. Haran, P. Ganesan, Ralph E. White, Branko N. Popov Jan 2003

Analysis Of Molten Carbonate Fuel Cell Performance Using A Three-Phase Homogeneous Model, N. Subramanian, B. S. Haran, P. Ganesan, Ralph E. White, Branko N. Popov

Faculty Publications

In this study a three-phase homogeneous model was developed to simulate the performance of the molten carbonate fuel cell (MCFC) cathode. The homogeneous model is based on volume averaging of different variables in the three phases over a small volume element. This approach can be used to model porous electrodes as it represents the real system much better than the conventional agglomerate model. Using the homogeneous model the polarization characteristics of the MCFC cathode was studied under different operating conditions.

Go to article

A Mathematical Model Of Oxide/Carbon Composite Electrode For Supercapacitors, Hansung Kim, Branko N. Popov Jan 2003

A Mathematical Model Of Oxide/Carbon Composite Electrode For Supercapacitors, Hansung Kim, Branko N. Popov

Faculty Publications

A pseudo two-dimensional model is developed for the general application of supercapacitors consisting of an oxide/carbon composite electrode. The model takes into account the diffusion of protons in the oxide particle by employing the method of superposition. RuO2/carbon system is modeled as a specific example. From the simulation data, it is found that the oxide particle size and proton diffusion coefficient have an enormous effect on the performance at high discharge rate due to the limitation of proton transport into RuO2 particles. With increasing carbon ratio, the porosity of electrode increases, which causes the potential drop in …

Go to article

A Novel Electrodeposition Process For Plating Zn-Ni-Cd Alloys, Hansung Kim, Branko N. Popov, Ken S. Chen Jan 2003

A Novel Electrodeposition Process For Plating Zn-Ni-Cd Alloys, Hansung Kim, Branko N. Popov, Ken S. Chen

Faculty Publications

Zn-Ni-Cd alloy was electrodeposited from an alkaline electrolytic bath under potentiostatic conditions. Bath analyses using a pH concentration diagram reveal that addition of a complexing agent is essential to maintain the bath stability. Introduction of a low concentration of CdSO4 reduces the anomalous nature of the Zn-Ni deposit. Deposits obtained from the electrolytic bath which contains 60 g/L of ZnSO4·7H2O, 40 g/L of NiSO4·6H2O, 1 g/L of CdSO4, and 80 g/L of (NH4)2SO4 in the presence of additives and ammonium hydroxide at pH 9.3 …

Go to article

Consensus Software: Robustness And Social Good, Michael N. Huhns Jan 2003

Consensus Software: Robustness And Social Good, Michael N. Huhns

Faculty Publications

In this column I explore some far-reaching issues of software development that lie at the intersection of robust software and sociopolitical systems. These two areas might seem unrelated-and most software developers would likely be horrified to have politics intrude on their programming efforts-but the intersection occurs through these premises: software systems administer and control much of our societal infrastructure; people would appreciate and better accept that control if they had input into the nature of the control and the systems' behavior; designers can make software systems more robust through redundancy, in which different versions of software components might cover for …

Go to article

Motion Planning Using Potential Fields, Randal W. Beard, Timothy W. Mclain Jan 2003

Motion Planning Using Potential Fields, Randal W. Beard, Timothy W. Mclain

Faculty Publications

The objective of these notes is to describe a reactive approach to motion planning for mobile robots. In a reactive approach, trajectories are not planned explicitly. Rather, robot interactions are defined explicitly and the robot motion is said to "emerge." The drawback of reactive methods is that it is sometimes difficult to get the robot to do exactly what you want. The reactive approach that will be described in these notes is called the "virtual fields" method and is commonly used in robotics.

Go to article

High-Pressure Intrinsic Oxidation Kinetics Of Two Coal Chars, William C. Hecker, Peter M. Madsen, Michael R. Sherman, Jared W. Allen, Rebecca J. Sawaya, Thomas H. Fletcher Jan 2003

High-Pressure Intrinsic Oxidation Kinetics Of Two Coal Chars, William C. Hecker, Peter M. Madsen, Michael R. Sherman, Jared W. Allen, Rebecca J. Sawaya, Thomas H. Fletcher

Faculty Publications

Chars were produced from two coals (North Dakota lignite and Pittsburgh No. 8 hva bituminous coal) in a flat flame burner at atmospheric pressure. Intrinsic char reactivities to oxygen were then measured in a high-pressure thermogravimetric analyzer as a function of temperature, total pressure, and partial pressure of oxygen. Care was taken to avoid mass transfer effects. Reactivities were normalized by the available mass of char at any given time (g/(gavailâs)). Reactivity data were obtained over a wide range of char burnout and were found to be independent of burnout level between char burnouts of 20 and 60%. Data were …

Go to article

High-Pressure Coal Pyrolysis In A Drop Tube Furnace, Koichi Matsuoka, Zhi-Xin Ma, Hiroyuki Akiho, Zhan-Guo Zhang, Akira Tomita, Thomas H. Fletcher, Marek A. Wojtowicz, Stephen Niksa Jan 2003

High-Pressure Coal Pyrolysis In A Drop Tube Furnace, Koichi Matsuoka, Zhi-Xin Ma, Hiroyuki Akiho, Zhan-Guo Zhang, Akira Tomita, Thomas H. Fletcher, Marek A. Wojtowicz, Stephen Niksa

Faculty Publications

To obtain useful and reliable pyrolysis data under high pressures, continuous pyrolysis experiments were carried out using a drop tube furnace. To ascertain the reliability of data, a mass balance during pyrolysis was carefully checked. The pyrolysis data obtained in this equipment was compared with previous results, and it was found that the weight loss observed in the drop tube furnace was somewhat larger than those obtained with other apparatuses. The experimental results were compared with those predicted by three pyrolysis models. Although discrepancies between predictions and experimental results were observed under a certain condition, the agreement between the experimental …

Go to article

Milliwatt Power Deep Ultraviolet Light-Emitting Diodes Over Sapphire With Emission At 278 Nm, J. P. Zhang, A. Chitnis, V. Adivarahan, S. Wu, V. Mandavilli, R. Pachipulusu, M. Shatalov, Grigory Simin, J. W. Yang, M. Asif Khan Dec 2002

Milliwatt Power Deep Ultraviolet Light-Emitting Diodes Over Sapphire With Emission At 278 Nm, J. P. Zhang, A. Chitnis, V. Adivarahan, S. Wu, V. Mandavilli, R. Pachipulusu, M. Shatalov, Grigory Simin, J. W. Yang, M. Asif Khan

Faculty Publications

We report on AlGaN multiple-quantum-well (MQW)-based deep ultraviolet light-emitting diodes over sapphire with peak emission at 278 nm. A new buffer layer growth process was used to reduce the number of defects and hence the nonradiative recombination. The improved material quality and carrier confinement resulted in pulsed powers as high as 3 mW at 278 nm and a significantly reduced deep-level-assisted long-wavelength emission.

Go to article

On-Chip Actuation Of An In-Plane Compliant Bistable Micromechanism, Michael S. Baker, Larry L. Howell Dec 2002

On-Chip Actuation Of An In-Plane Compliant Bistable Micromechanism, Michael S. Baker, Larry L. Howell

Faculty Publications

A compliant bistable micromechanism has been developed which can be switched in either direction using on-chip thermal actuation. The energy storage and bistable behavior of the mechanism is achieved through the elastic deflection of compliant segments. The Pseudo-Rigid-Body Model was used for the compliant mechanism design, and for analysis of the large deflection flexible segments. To achieve on-chip actuation, the mechanism design was optimized to allow it to be switched using linear motion thermal actuators. The modeling theory and analysis are presented for three design iterations, with two iterations fabricated in the MUMP's process and the third in the SUMMiT …

Go to article

An Assessment Of Seawinds On Quikscat Wind Retrieval, David Draper, David G. Long Dec 2002

An Assessment Of Seawinds On Quikscat Wind Retrieval, David Draper, David G. Long

Faculty Publications

The scatterometer ocean wind retrieval process produces several possible solutions or ambiguities at each point, requiring a separate ambiguity selection step to infer a unique wind vector field. An ambiguity selection error occurs when the selected wind vector is not the closest ambiguity to the true wind. The current ambiguity selection routine for SeaWinds is ad hoc, but performs well under most circumstances. Factors such as instrument noise and rain can also cause the estimated wind flow to deviate from the true wind. A quality assurance (QA) analysis is performed to assess the ambiguity selection effectiveness and noise level of …

Go to article

Polarization Effects In Photoluminescence Of C- And M-Plane Gan/Algan Multiple Quantum Wells, E. Kuokstis, C. Q. Chen, M. E. Gaevski, W. H. Sun, J. W. Yang, Grigory Simin, M. Asif Khan, H. P. Maruska, D. W. Hill, M. C. Chou, J. J. Gallagher, B. Chai Nov 2002

Polarization Effects In Photoluminescence Of C- And M-Plane Gan/Algan Multiple Quantum Wells, E. Kuokstis, C. Q. Chen, M. E. Gaevski, W. H. Sun, J. W. Yang, Grigory Simin, M. Asif Khan, H. P. Maruska, D. W. Hill, M. C. Chou, J. J. Gallagher, B. Chai

Faculty Publications

Polarizationeffects have been studied in GaN/AlGaN multiple quantum wells(MQWs) with different c-axis orientation by means of excitation-dependent photoluminescence(PL) analysis. Quantum structures were grown on [0001]-oriented sapphire substrates (C plane) and single-crystalline [11̄00]-oriented freestanding GaN (M plane) using the metalorganic chemical vapor deposition technique. Strong PL spectrum line blueshifts (up to 140 meV) which are correlated with the excitation intensity have been obtained for C-plane MQWs, whereas no shift has been observed for M-plane MQWs.Theoretical calculations and comparison with the PL data confirm that the built-in electric field for C-plane structures is much stronger than the field present for M-plane MQWs. …

Go to article

Mapping The Mesoscale Interface Structure In Polycrystalline Materials, Brent L. Adams, C. L. Bauer, D. Casasent, A. Morawiec, S. Ozdemir, A. Talukder, Chialin T. Wu Nov 2002

Mapping The Mesoscale Interface Structure In Polycrystalline Materials, Brent L. Adams, C. L. Bauer, D. Casasent, A. Morawiec, S. Ozdemir, A. Talukder, Chialin T. Wu

Faculty Publications

This work was supported primarily by the MRSEC Program of the National Science Foundation under Award Numbers DMR-9632556 and DMR-0079996. A new experimental approach to the quantitative characterization of polycrystalline microstructure by scanning electron microscopy is described. Combining automated electron backscattering diffraction with conventional scanning contrast imaging and with calibrated serial sectioning, the new method (Mesoscale Interface Mapping System, MIMS) recovers precision estimates of the 3-dimensional idealized aggregate function G(x). This function embodies a description of lattice phase and orientation (limiting resolution ~ 1 degree) at each point x (limiting spatial resolution ~ 100 nanometers), and therefore contains a complete …

Go to article

Distributions Of Nobel Metal Pd And Pt In Mesoporous Silica, J. Arbiol, A. Cabot, J. R. Morante, Fanglin Chen, Meilin Liu Oct 2002

Distributions Of Nobel Metal Pd And Pt In Mesoporous Silica, J. Arbiol, A. Cabot, J. R. Morante, Fanglin Chen, Meilin Liu

Faculty Publications

Mesoporous silicananostructures have been synthesized and loaded with Pd and Pt catalytic noble metals. It is found that Pd forms small nanoclusters (3–5 nm) on the surface of the mesoporous structure whereas Pt impregnation results in the inclusion of Pt nanostructures within the silica hexagonal pores (from nanoclusters to nanowires). It is observed that these materials have high catalyticproperties for CO–CH4CO–CH4CO–CH4 combustion, even in a thick film form. In particular, results indicate that the Pt and Pd dispersed in mesoporous silica are catalytically active as a selective filter for gas sensors.

Go to article

Distributions Of Noble Metal Pd And Pt In Mesoporous Silica, J. Arbiol, A. Cabot, J. R. Morante, Fanglin Chen, Meilin Liu Oct 2002

Distributions Of Noble Metal Pd And Pt In Mesoporous Silica, J. Arbiol, A. Cabot, J. R. Morante, Fanglin Chen, Meilin Liu

Faculty Publications

Mesoporous silica nanostructures have been synthesized and loaded with Pd and Pt catalytic noble metals. It is found that Pd forms small nanoclusters (3–5 nm) on the surface of the mesoporous structure whereas Pt impregnation results in the inclusion of Pt nanostructures within the silica hexagonal pores (from nanoclusters to nanowires). It is observed that these materials have high catalytic properties for CO–CH4 combustion, even in a thick film form. In particular, results indicate that the Pt and Pd dispersed in mesoporous silica are catalytically active as a selective filter for gas sensors.

Go to article

Gan Homoepitaxy On Freestanding (11̄00) Oriented Gan Substrates, C. Q. Chen, M. E. Gaevski, W. H. Sun, E. Kuokstis, J. P. Zhang, R. S. Q. Fareed, H. M. Wang, J. W. Yang, Grigory Simin, M. A. Khan, Herbert-Paul Maruska, David W. Hill, Mitch M. C. Chou, Bruce Chai Oct 2002

Gan Homoepitaxy On Freestanding (11̄00) Oriented Gan Substrates, C. Q. Chen, M. E. Gaevski, W. H. Sun, E. Kuokstis, J. P. Zhang, R. S. Q. Fareed, H. M. Wang, J. W. Yang, Grigory Simin, M. A. Khan, Herbert-Paul Maruska, David W. Hill, Mitch M. C. Chou, Bruce Chai

Faculty Publications

We report homoepitaxialGaNgrowth on freestanding (11̄00) oriented (M-plane GaN) substrates using low-pressure metalorganic chemical vapor deposition.Scanning electron microscopy,atomic-force microscopy, and photoluminescence were used to study the influence of growth conditions such as the V/III molar ratio and temperature on the surface morphology and optical properties of the epilayers. Optimized growth conditions led to high quality (11̄00) oriented GaN epilayers with a smooth surface morphology and strong band-edge emission. These layers also exhibited strong room temperature stimulated emission under high intensity pulsed optical pumping. Since for III-N materials the (11̄00) crystal orientation is free from piezoelectric or spontaneous polarization electric fields, …

Go to article

Low-Temperature Operation Of Alfan Single-Quantum-Well Light-Emitting Diodes With Deep Ultraviolet Emission At 285 Nm, A. Chitnis, R. Pachipulusu, V. Mandavilli, M. Shatalov, E. Kuokstis, J. P. Zhang, V. Adivarahan, S. Wu, Grigory Simin, M. Asif Khan Oct 2002

Low-Temperature Operation Of Alfan Single-Quantum-Well Light-Emitting Diodes With Deep Ultraviolet Emission At 285 Nm, A. Chitnis, R. Pachipulusu, V. Mandavilli, M. Shatalov, E. Kuokstis, J. P. Zhang, V. Adivarahan, S. Wu, Grigory Simin, M. Asif Khan

Faculty Publications

We present a study of the electrical and optical characteristics of 285 nm emission deep ultraviolet light-emitting diodes(LED) at temperatures from 10 to 300 K. At low bias, our data show the tunneling carrier transport to be the dominant conduction mechanism. The room-temperature performance is shown to be limited mostly by poor electron confinement in the active region and a pronounced deep level assisted recombination but not by the hole injection into the active region. At temperatures below 100 K, the electroluminescence peak intensity increases by more than one order of magnitude indicating that with a proper device design and …

Go to article

First Prev Next Last