Engineering Commons^™

Exploring The Feasibility Of Innovative Integration Of Phase Change Materials For Thermo-Adaptive Asphalt Pavements, Farshad Saberi Kerahroudi

Doctoral Dissertations

"Current research examined the feasibility and efficiency of employing phase change materials (PCMs) in asphalt pavement materials to result in thermo-adaptive asphalt pavement. The PCM was introduced to the asphalt materials in three different scales, including asphalt binder, asphalt mastic, and asphalt mixture. After investigating asphalt at different scales, mix blending method was found as the easiest method without any complexity to mix asphalt binder with PCM. The testing results could reveal an improvement in the high temperature performance of asphalt binder without sacrificing the low temperature performance with the presence of PCM and Gilsonite. Also, introducing PCM to asphalt …

Systematic Esd Analysis And Modeling For Electronic Device, Zhekun Peng

Doctoral Dissertations

Systematic ESD analysis provides good pre-compliance to ESD robustness evaluation on the electronic device from device level to component/system level to on-chip level. The whole process involves corona discharge on display, system level ESD analysis on PCB for race condition and transient response and 3D IC package impact to on-die ESD.

ESD to the display cover glass can damage touchscreen traces by sparkless corona discharges on the glass surface. A non-linear time dependent transmission-line model is proposed to model corona streamer propagation in terms of the coupling current and propagation speed. Results are highly promising to model the corona discharge …

Nutrient Fate, Mass Balance, Species Selection, And Plant Management Strategies With Floating Treatment Wetlands, Carla Campbell

Doctoral Dissertations

Excess nutrients in shallow urban ponds can lead to harmful algal blooms, low dissolved oxygen, and internal phosphorus cycling. These effects can compromise municipal water supplies and cause negative impacts on fisheries and recreation. Floating treatment wetlands (FTWs) show promise to mitigate surface water nutrient pollution. However, despite recent research, many aspects of FTWs remain poorly characterized. The contribution of FTW components to nutrient removal, local species selection, and plant management strategies were the focus of this dissertation. Mesocosm experiments revealed that the combination of plants and coir fiber growth media in FTWs appeared to positively affect plant biomass gain …

Radio Frequency Wave Propagation Modeling Within Obstructed Underground Mining Environments For Effective Miner Localization During Mine Emergencies, Emmanuel Atta Antwi

Doctoral Dissertations

The reliability of underground wireless communication systems remains a significant challenge, particularly during emergencies when the mine environment becomes severely obstructed by debris, dust, and humidity. These environmental and geometric conditions result in significant attenuation of electromagnetic (EM) waves and multipath effects that undermine miner localization and rescue operations. Existing Vector Parabolic Equation (VPE) models are efficient for straight or mildly curved tunnels but fail to account for the random and obstructive conditions typically encountered during underground emergencies. This research develops a novel radio propagation model for EM wave behavior in underground mine drifts under geometrically obstructed conditions. The model …

Mitigating Frost Heave And Thaw Weakening In Roads Using Wicking Geotextile, Javad Galinmoghadam

Doctoral Dissertations

"Excess water is known to be the primary cause of soil and foundation problems. In cold regions, water-related problems are exacerbated by seasonal freezing and thawing cycles. Frost heave and thaw weakening is the leading cause of premature pavement failure and consume considerable budgets of the Department of Transportations in cold regions. The first step to designing mitigation measures is the ability to predict frost heave under different conditions. This study aims to introduce a new method for quantifying frost heave using a prediction model based on the state surface approach. This proposed model addressed many inconsistencies and limitations of …

Applying Human System Integration Principles To The Investigation, Design And Validation Of Interventions For Self-Escape In Underground Mines, Eugene Adubofour Gyawu

Doctoral Dissertations

This dissertation investigates the use of human systems integration (HSI) to develop technologies for miners’ self-escape during a mine emergency, addressing barriers that compromise miner safety during emergencies.

Recognizing the inherently hazardous nature of underground mining, this study has three core objectives: (1) assessing miners' perceptions of proposed self-escape interventions, (2) designing interventions based on these insights, and (3) validating their effectiveness using experimental testing. This work evaluates self-escape interventions for both coal and metal/non-metal miners using scenario-based surveys, information design reviews, label designs and experimental testing methods varying across three distinct studies.

Results reveal that miners identified improvements to …

Mid-Field Shock And Impulse Estimation Methods For Blast Loading On Tall Targets, Ethan Allan Steward

Doctoral Dissertations

Blast resistant structural design continues to be a major research area for governments around the world due to explosive threats from both state and non-state actors. Many of the typical targets of explosive attacks, such as government buildings, commercial high rise office buildings, and apartment complexes are mid to high-occupancy buildings that present a tall profile relative to the charge size and are often clad in curtain walls. In blast resistant structural design, the origin of a shock wave is typically assumed to be in the far-field, creating a wave that is nearly planar and parallel to at least one …

Supporting Human-Ai Interaction From User Expectations To Mental Models, Harishankar Vasudevanallur Subramanian

Doctoral Dissertations

Explainable AI (XAI) aims to unravel the "black box" nature of AI systems and provide insights into the inner workings that lead to a prediction. However, the best XAI communication varies depending on the individual, task, and broader context. It is challenging to anticipate the best XAI for a particular use case. One strategy is for users to build an appropriate mental model of AI with both prediction and system level XAI. To date, little research has focused on quantitatively measuring users interacting with system-level XAI. This dissertation has three primary contributions. The first contribution is a scoping review paper …

Metal-Organic Thin Film Coated On Optical Fiber, Nahideh Salehifar

Doctoral Dissertations

This dissertation explores the development of metal-organic framework (MOF)-based optical fiber sensors for detecting volatile organic compounds (VOCs) at low concentrations (parts-per-billion to parts-per-million). In the first part of the study, theoretical calculations were performed using effective medium approximation (EMA) models, including Lorentz–Lorentz, Maxwell–Garnett, and Bruggeman equations, to predict the refractive index changes of MOFs upon gas adsorption. These models were applied to MOFs such as ZIF-7, ZIF-8, ZIF-90, MIL-101(Cr), and HKUST-1 to evaluate their potential for gas sensing.

In the second part of the dissertation, experimental work was conducted to validate the theoretical predictions. MOF-coated optical fibers were fabricated …

Evaluating And Relaxing The Limits On Flexural Reinforcement Ratio Of Masonry Shear Walls, Tousif Mahmood

Doctoral Dissertations

Reinforced masonry shear walls (RMSWs), essential for lateral and out-of-plane load-resisting systems in modern construction are constrained by TMS 402/602 code limits on reinforcement ratios ("ρ" _"max" ) and axial compressive stresses (≤10% of masonry compressive strength, f_m^'), undermining masonry’s inherent compression capacity under high axial loads. This dissertation investigates the seismic performance of reinforced masonry shear walls (RMSWs) subjected to high axial compressive stresses (10–20% of f_m^'), with a focus on walls violating the maximum reinforcement ratio ("ρ" _"max") and axial load limits of TMS 402-22. Through experimental testing of 30 large-scale fully grouted (FG) and partially grouted (PG) …

Experimental Study Of Defects In Coaxial Wire-Based Laser Metal Deposition, Remy Mathenia

Doctoral Dissertations

This work seeks to improve the usability and capability of coaxial wire-based laser metal deposition (LMD) through the experimental study of process parameters on output geometry, directional effects, and defect formation. Wire-based LMD is a directed energy deposition (DED) strategy that uses a focused laser heat source to melt and fuse metal wire as it is deposited. This process is used to build parts layer-by-layer until a desired geometry is accomplished. LMD enables the creation of complex components at a high build rate with low material and energy waste. This work focuses on the deposition of titanium wire in the …

Measurement Method And Applications Of Transfer Function In Rf Desensitization Problem, Xiangrui Su

Doctoral Dissertations

Radio frequency (RF) desensitization issues comprise two components: noise radiation sources and the transfer function from noise sources to the victim antenna. RFI is a critical challenge in modern electronic systems, particularly in densely packed environments. This work presents a comprehensive study of RFI, addressing key aspects through three novel contributions. First, a transfer function measurement method is developed for compact metallic enclosures. This method provides a precise characterization of the electromagnetic (EM) environment within confined spaces, enabling accurate identification of interference pathways. Second, an EM emission management analysis framework is proposed, leveraging transfer functions to quantify and mitigate interference …

The Structure, Properties And Dissolution Behaviors Of Phosphate Glasses, Han Zhang

Doctoral Dissertations

The poor chemical durability remains a critical challenge for the application of phosphate glasses. This study investigates the compositional influences on the structure, properties and chemical durability of Li2O-ZnO-P₂O₅ glasses. Their structural characteristics were analyzed utilizing high-performance liquid chromatography, Raman spectroscopy, and X-ray photoelectron spectroscopy. The incorporation of (Li2O+ZnO) in LZeq glasses depolymerizes the phosphate network. In LZ40P and LZ45P glasses, Li⁺ initially replaces Zn²⁺ associated with non-bridging oxygens (NBOs) in Q² tetrahedra. Once the substitution in Q² is complete, further Li⁺ incorporation leads to the replacement of Zn²⁺ in Q^{1 …}

Design Of Real-Time And Energy-Efficient Driver Assist Systems Using Electroencephalogram And Neuromorphic Computing, Nathan Alan Lutes

Doctoral Dissertations

Despite the technological breakthroughs in advanced driver assist systems, distracted driving persists as a major challenge to roadway safety. This investigation advances the body of knowledge towards a solution by developing an individualized driver-state detection method using electroencephalogram (EEG) and neuromorphic computing to provide a less invasive and more energy efficient ADAS solution. It furthermore explores the changes in brain functional connectivity under distracted conditions to better understand brain state information that could be used for neuro-feedback intervention systems. The first contribution introduces the concept of using Convolutional Spiking Neural Networks (CSNNs) for recognition of patterns with movement-intention predictive power …

Novel Nano-Formulations Based On Flash Nanoprecipitation For Ocular Drug Delivery, Lin Qi

Doctoral Dissertations

Effective ocular drug delivery has always been a challenge for clinical and research. Although many nanotechnology-based formulations have been developed and showed great potential in ocular drug delivery, this is far from enough to meet clinical requirements. These studies aimed at the design and synthesis of novel nanoparticles using multi-inlet vortex mixer (MIVM) to improve ocular drug delivery efficiency. The first project involves packaging two different anti-glaucoma drugs, brimonidine (BM) and betaxolol (BX), into solid drug nanoparticles (SDNs) by MIVM, which can achieve both functions, reducing aqueous humor production and promoting aqueous humor efflux. The studies demonstrate that the SDNs …

Higher-Order Statistics And Normalized Decay Analysis For Detector Deadtime Characterization, Abdallah Wazzan

Doctoral Dissertations

Detector deadtime limits radiation measurement accuracy at high count rates, yet current methods rely on idealized paralyzable or non-paralyzable models. Real detectors exhibit hybrid behavior requiring advanced characterization approaches. This study explores deadtime characterization using two Monte Carlo simulation approaches: higher-order statistical analysis of inter-arrival times and simplified deadtime correction with hybrid models.

Using MATLAB (PULSE-WIZ), we analyzed full decay curves spanning ~4.5 half-lives of Cobalt-60 and Vanadium-52, examining coefficient of variation (CV), skewness, and kurtosis of inter-arrival times, plus normalized decay curves with Full Width at Half Maximum (FWHM) analysis. Hybrid models incorporated paralyzable and non-paralyzable components with dead …

Development, Characterization And Testing Of Traditonal And Advanced Nuclear Fuel Cladding Materials, Joshua Eddy Rittenhouse

Doctoral Dissertations

Kanthal D and FeCrAl alloys in general, are prospective candidates as accident tolerant nuclear fuel cladding materials. The work presented herein focuses on applying two techniques of severe plastic deformation, equal channel angular pressing (ECAP) and high-pressure torsion (HPT), as means of grain refinement to improve irradiation resistance. Samples of as-received, ECAP, and HPT processed Kanthal D were exposed to neutron irradiation to a dose of 2 DPA at two different temperatures, 300 °C and 500 °C. Detailed characterization was performed including mechanical and microstructural, and several positive improvements with regards to irradiation resistance were identified in the ECAP and …

Enhanced Optimization Of Mass Transfer For Carbon Capture And Wastewater Remediation In Algal Systems Through Algorithmic And Bioprocessing Techniques, Peter Ofuje Obidi

Doctoral Dissertations

The scalability and industrial deployment of algal cultivation systems are limited by suboptimal mass transfer, constraining their effectiveness in carbon capture and wastewater remediation. This research investigated these challenges through integrated optimization methodologies that combine algorithmic frameworks with enhanced bioprocessing techniques to enhance efficiency, economy, and scalability. A System-of-Systems (SoS) meta-architecture was developed using genetic algorithms and fuzzy assessor functions to demonstrate a pathway toward cost reduction. Rigorous mechanical and chemical characterizations were quantitatively analyzed to reveal existing optimization strategies and further evaluated the best strategies to use in enhancing mass transfer for improved biomass yield. The work also integrates …

Dynamic Response, Assessment, And Retrofitting Of Prestressed Concrete Bridge Girders Subjected To Lateral Impact Loads, Haitham A. Abdelmalek

Doctoral Dissertations

Over height vehicle collisions pose a growing threat to the resilience of bridge infrastructure across the United States. According to the American Road & Transportation Builders Association (ARTBA, 2024), approximately 36% of all U.S. bridges require major repair or replacement, with an estimated cost of $400 billion. This dissertation investigates the structural dynamic response, damage assessment, and retrofitting strategies for prestressed concrete (PC) bridge girders subjected to lateral impact loading.

The research comprised two main phases: (1) numerical modeling and (2) experimental testing. A validated 3D nonlinear finite element (FE) model was developed to conduct parametric studies on impact behavior, …

Synthesis Of Graphene Using Carbonaceous Materials In An Ultrasonic Reactor, Paul Chukwuma Ani

Doctoral Dissertations

The synthesis of high-quality graphene from sustainable carbonaceous feedstocks offers an avenue to reduce the environmental and economic costs associated with conventional graphite-based production. This research investigates the co-utilization of biochar and graphite as precursors for graphene fabrication in an ultrasonic reactor. Biochar was produced from biomass via downdraft gasification at 850 °C, yielding a high fixed-carbon, partially graphitized material with favorable surface area and porosity. Graphite, selected for its crystalline structure, was investigated with biochar to assess the influence of precursor composition on exfoliation efficiency, layer thickness distribution, and defect density. Ultrasonic-assisted liquid-phase exfoliation was employed, with process parameters …

Advancements In Signal Processing And Image Reconstruction For Active Microwave Thermographic Measurements, Logan Martin Wilcox

Doctoral Dissertations

Active microwave thermography, or AMT, is a coupled electromagnetic-thermographic nondestructive testing and evaluation technique. AMT has found success in a variety of inspection needs in the aerospace, space, and infrastructure fields due to its unique type of thermal excitation. During an AMT inspection, a specimen is exposed to microwave energy from a radiating source (i.e., an antenna). This exposure to microwave energy results in dielectric/magnetic heating, which causes an increase in temperature and potential defect indications to manifest on an inspection surface (which is measured via an infrared camera). Due to the use of an antenna, there is a spatially …

Deep Learning Architecture Design For Nano-Satellite Image Super-Resolution, William Everette Symolon

Doctoral Dissertations

Increasing threats to U.S. national security satellite constellations have resulted in an increased interest in constellation resilience and satellite redundancy. NanoSats have contributed to commercial, scientific and government applications in remote sensing, communications, navigation, and research. They also have the potential to enhance satellite constellation resilience. However, the inherent size, weight, and power limitations of NanoSats enforce constraints on imaging hardware; the small lenses and short focal lengths result in imagery with low spatial resolution, which limits the utility of CubeSat images for military planning purposes and national intelligence applications. This research proposed a deep learning architecture capable of enhancing …

Investigating The Effects Of Fly Ash On The Properties Of Silica-Deficient High Alumina Materials, Sai Akshay Ponduru

Doctoral Dissertations

This research is made up of five studies mainly focused on attaining sustainability in high alumina cements like calcium aluminate cement (CAC) and calcium sulfoaluminate belite cements (CSAB) by partially replacing them with additives and supplementary cementitious materials (SCMs) like fly ash (FA). The first study focused on understanding the reaction kinetics of CAC and FA binders at different replacement levels (i.e. between 10%-to-50% by mass) and their effect on mechanical properties. It was also shown that the reactive nature of FAs can be determined by calculating a single parameter called number of constraints (nc) derived from topological constraint theory. …

Data-Driven Mulitiscale Modeling Of Electrochemical Transport, Non-Linear Electrical Contact, And Additive Manufacturing Processes, Emmanuel Olugbade

Doctoral Dissertations

The growing demand for high-efficiency energy systems and advanced manufacturing technologies requires predictive frameworks that link atomic-scale physics with engineering-scale performance. This dissertation develops a unified multiscale modeling approach that integrates molecular dynamics, density functional theory, finite-element analysis, and machine learning to connect structure, transport, and performance across materials and processes. Depending on the interactions involved, the framework employs loose coupling for parameter transfer, tight coupling for two-way feedback, and hybrid coupling where machine-learning surrogates accelerate high-fidelity simulations while retaining physical interpretability. In electrochemical systems, an XGBoost-enhanced single-particle model reproduces P2D-level electrolyte potential dynamics at roughly one-hundredth the computational cost, …

Characterization And Deportment Of Anode Impurities In Copper Electrorefining, Charles Michael Campbell

Doctoral Dissertations

The objective of this research was to study the deportment of the group 15 elements, arsenic, antimony and bismuth during copper electrorefining. Samples were collected from six industrial copper anodes with different compositions. Specimens were physically characterized and electro refined to understand the differences in the behavior of selected impurities. Inclusions in the cast metal structures were characterized using automated scanning electron microscopy and energy dispersive spectroscopy to measure and correlate their size, shape and composition. Arsenic and lead were found to have a positive correlation between concentration and size of inclusions. Using wavelength dispersive spectroscopy, multiphase inclusions were examined, …

Optical Sensor Instrumentation For Enhanced Continuous Caster Development, Hanok Wondimagegnehu Tekle

Doctoral Dissertations

Fiber-optic sensors are an emerging technology that can enhance process monitoring and control in steelmaking. They are especially valuable in the continuous caster’s harsh environment. This dissertation presents the industrial application and demonstration of three sensor types: single-mode silica fiber with Rayleigh-based Optical Frequency Domain Reflectometry (OFDR), sapphire fiber (single-crystal alumina) with Fiber Bragg Gratings (sFBG), and an in-line Raman spectroscopy probe. Each sensor served a distinct role in the continuous caster. Rayleigh OFDR sensors were embedded in tundishes for distributed thermal mapping at 7-mm spatial resolution across ≈4 m. Measurements were taken during preheating, casting, and ladle exchanges, and …

Identification Of Corrosion Damage, Vibration, And Loose Conections In Aircraft Data Transmission Lines Using Reflected And Transmitted Signals; Formulation Of Vegetable Oil-Based Nanofluids As Cutting Fluids For Mql Machining, Saidanvardzhon Valiev

Doctoral Dissertations

This research presents a novel Frequency Domain Transmitometry (FDT) method that uses transmitted signals (S21) to detect and characterize aircraft data transmission lines (ADTL) corrosion damage without additional reflectometry circuitry. Corrosion experiments were conducted according to ASTM G85-A5 over 14 weeks. Combined FDT and reflected signals (S11) analyses revealed distinct three-peak signatures associated with damage and corrosion. The square root of the Area Under the Curve (AUC) of the FDT damage peak and the Full Width at Three-Quarter Maximum (FW3QM) of the S11 damage peak is correlated with corrosion propagation depth and width. S11 signals were further used for vibration …

Effect Of Thermomechanical Processing And Heat Treatment On The Microstructure And Mechanical Properties Of Ultra-High Strength Steels, Rogerio Antao Cardoso

Doctoral Dissertations

"A martensite-based and an austenite-based Fe-Mn-Al steels were investigated aiming the pilot-scale production of steels that meet military specifications for Rolled Homogeneous Armor (RHA) and High-hardness Armor (HHA) plates. Each material underwent specific thermomechanical processes and the following hardness, Charpy V-notch (CVN) impact toughness at -40 °C and room-temperature tensile properties were correlated with the resulting microstructures.

Specimens of the martensitic steel were austenitized at 1010 °C, quenched and tempered at 150, 175, 200, 225 and 250 °C for times up to four hours. As for the Fe-Mn-Al steel, its hot rolling schedule was design to promote strain accumulation in …

Selected Topics In Blockchain-Aided Iot Inference, Yiming Jiang

Doctoral Dissertations

"Blockchain has recently been considered in the Internet of Things (IoT) to secure data exchanges and storage across various engineering applications. This newly emerging blockchain-aided IoT (BIoT) network has been applied to a great deal of security-related applications. However, the BIoT still has the vulnerability that can be exploited by attackers, potentially impairing the performance of BIoT applications. Despite this, research addressing the vulnerability has been limited. This work presents four studies aimed at addressing critical gaps in current BIoT research.

The first study introduces a Time-Restricted Double-Spending Attack (TR-DSA) model for Proof-of-Work (PoW)-based blockchains, where the adversary only conducts …

Drone-Based Multimodal Sensing On Vegetations And Data Analytics For Early Detection Of Gas Leakage From Underground Pipelines, Pengfei Ma

Doctoral Dissertations

"This study explored the feasibility of using multimodal remote sensors in the early detection of natural gas leaks from underground pipelines, as vegetation situated above pipelines can discern microbial changes in soil when affected by gas and exhibit physiological stress symptoms on leaves. Three sensors (RBG, thermal, and hyperspectral cameras) were utilized to monitor vegetation stress as an indicator of gas leaks. A laboratory experiment was conducted to evaluate the workability of vegetation for gas leak detection. Regular hyperspectral imagery was collected from test vegetations to identify gas stress and distinguish it from other environmental stressors such as salinity impact, …