Engineering Commons^™

Test 2223: John Deere 8r 370, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2224: John Deere 8r 410, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2228: John Deere 8rx 410, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary 1194: John Deere 6145m Ft4, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Feasibility Study Of Development Of Ultra-High Performance Concrete (Uhpc) For Highway Bridge Applications In Nebraska, Flavia Ribeiro Furtado De Mendonca, Mostafa Abo El-Khier, George Morcous, Jiong Hu

Nebraska Department of Transportation: Research Reports

Ultra-high performance concrete (UHPC) is a new class of concrete that has superior mechanical, durability, and workability properties that far exceed those of conventional concrete. To achieve these properties, a specific mix design with a very dense internal structure, fiber reinforcement, and low water-to-binder ratio (w/b) is commonly used. The goal of this research is to develop a non-proprietary UHPC mix with constituent materials that are readily available in the state of Nebraska for bridge construction applications. In developing this mix, the particle packing model is used, and an experimental study of the impact of various design parameters on the …

Evaluation Of Tie-Bar Anchoring Methods: Non-Shrink Grout Vs. Epoxy, Wally Heyen, Lieska Halsey, Tim Krason, Brandon Varilek, David Hansen

Nebraska Department of Transportation: Research Reports

Tie bars are epoxy coated steel bars that connect the longitudinal joints in concrete pavement. Tie bars prevent faulting and joint separation between lanes Tie bars can be placed into the plastic concrete or inserted after curing by drilling and anchoring with epoxy or non-shrink grout. The specification for the tie bars requires the use of a No. 5 bar, 18 inches long and shall meet ASTM A775 / A775M [1], Section 1020.The Nebraska Department of Transportation “Standard Specifications for Highway Construction,” (Section 603.03) requires contractors to mechanically insert tie bars into the face of pavements during construction. Tie bars …

Influence Of Curing Conditions On Concrete Specimens (Cylinders) In Hot And Cold Weather In The Field, Wally Heyen, Lieska Halsey, Tim Krason, David Hansen

Nebraska Department of Transportation: Research Reports

No abstract provided.

Designing Shared Control Strategies For Teleoperated Robots Across Intrinsic User Qualities, Nancy Pham

School of Computing: Dissertations, Theses, and Student Research

Accounting for variance in human behavior is an integral part of interacting with robotic systems that share control between users and robots in order to reduce errors, improve performance, and maintain safety. In this work we focus on the shared control of a telepresence robot and how individual user traits may affect a person's performance while navigating the robot. This requires understanding which user qualities impact performance and cause conflicts -- with the ultimate goal of building shared controllers that adapt to those qualities. Toward this goal, we develop novel adaptive shared controllers and integrate the study of intrinsic user …

Site-Specific Irrigation Management In A Sub-Humid Climate Using A Spatial Evapotranspiration Model With Satellite And Airborne Imagery, Sandeep Bhatti, Derek M. Heeren, J. Burdette Barker, Christopher M. U. Neale, Wayne Woldt, Mitchell S. Maguire, Daran Rudnick

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Variable Rate Irrigation (VRI) considers spatial variability in soil and plant characteristics to optimize irrigation management in agricultural fields. The advent of unmanned aircraft systems (UAS) creates an opportunity to utilize high-resolution (spatial and temporal) imagery into irrigation management due to decreasing costs, ease of operation, and reduction of regulatory constraints. This research aimed to evaluate the use of UAS data for VRI, and to quantify the potential of VRI in terms of relative crop and water response. Irrigation treatments were: (1) VRI using Landsat imagery (VRI-L), (2) VRI using UAS imagery (VRI-U), (3) uniform (U), and (4) rainfed (R). …

An Automated Seepage Meter For Streams And Lakes, D. Kip Solomon, Eric Humphrey, Troy E. Gilmore, David P. Genereux, Vitaly Zlotnik

Department of Agricultural and Biological Systems Engineering: Faculty Publications

We describe a new automatic seepage meter for use in soft bottom streams and lakes. The meter utilizes a thin‐walled tube that is inserted into the streambed or lakebed. A hole in the side of the tube is fitted with an electric valve. Prior to the test, the valve is open and the water level inside the tube is the same as the water level outside the tube. The test starts with closure of the valve, and the water level inside the tube changes as it moves toward the equilibrium hydraulic head that exists at the bottom of the tube. …

Automatic Wheat Lodging Detection And Mapping In Aerial Imagery To Support High-Throughput Phenotyping And In-Season Crop Management, Biquan Zhao, Jiating Li, P. Stephen Baenziger, Vikas Belamkar, Yufeng Ge, Jian Zhang, Yeyin Shi

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Latest advances in unmanned aerial vehicle (UAV) technology and convolutional neural networks (CNNs) allow us to detect crop lodging in a more precise and accurate way. However, the performance and generalization of a model capable of detecting lodging when the plants may show different spectral and morphological signatures have not been investigated much. This study investigated and compared the performance of models trained using aerial imagery collected at two growth stages of winter wheat with different canopy phenotypes. Specifically, three CNN-based models were trained with aerial imagery collected at early grain filling stage only, at physiological maturity only, and at …

A Novel Structural Health Monitoring Method For Reinforced Concrete Bridge Decks Using Ultrasonic Guided Waves, Ece Erdogmus, Eric Garcia, Ahmad Shoaib Amiri, Michael Schuller

Durham School of Architectural Engineering and Construction: Faculty Publications

This article presents the latest improvements in a recently developed nondestructive testing (NDT) approach for early detection of various flaws (corrosion, delamination, and concrete cracking) in reinforced concrete (RC) bridge decks. The proposed method involves the use of internal steel reinforcement as a wave guide for transmitting ultrasonic waves through the system and the measurement of leaked energy from the surface of the concrete. This paper builds upon the progress made in the previously published phases of the project and aims to further explore the capabilities and practicality of the proposed NDT method. Specifically, the limits of propagation distance, effect …

Analysis Of The Variability Of Project Cost And Schedule Performance In The Design-Build Environment, Yunping Liang, Baabak Ashuri, Wei Sun

Durham School of Architectural Engineering and Construction: Faculty Publications

Design-build (DB) projects are getting more implementations in the United States. Several studies indicate that the DB project delivery system has advantages in project cost and schedule performance. Despite having comparative advantages, DB projects are found to be far from immune from cost overruns and schedule delay in those studies. It is critical to understand the effects of various factors underpinning the cost and schedule performance of DB projects. The overall objective of this research is to utilize cluster analysis and statistical analysis to identify factors with significant potentials to describe the variability of project cost and schedule performance in …

Option Value Of Contingent Finance Support In Transportation Public-Private Partnership Projects, Yunping Liang, Baabak Ashuri

Durham School of Architectural Engineering and Construction: Faculty Publications

Uncertainties about construction cost and operational revenues are two major risks in transportation public-private partnership (P3) projects. These uncertainties put projects at risk of being unable to fulfill annual debt repayment obligations. When a project generates insufficient cash flow to service the debt in a certain year, it normally has to go for short-term financing by borrowing short-term loans. With the help of revenue risk-sharing mechanisms, supported projects may be able to get rid of unexpected interest disbursement. The objectives of this paper are twofold: (1) evaluate the refinancing cost of P3 highway projects caused by cash flow shortage and …

Ground And Aerial Robots For Agricultural Production: Opportunities And Challenges, Santosh Pitla, Sreekala Bajwa, Santosh Bhusal, Tom Brumm, Tami M. Brown-Brandl, Dennis R. Buckmaster, Isabella Condotta, John Fulton, Todd J. Janzen, Manoj Karkee, Mario Lopez, Robert Moorhead, Michael Sama, Leon Schumacher, Scott Shearer, Alex Thomasson

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Crop and animal production techniques have changed significantly over the last century. In the early 1900s, animal power was replaced by tractor power that resulted in tremendous improvements in field productivity, which subsequently laid foundation for mechanized agriculture. While precision agriculture has enabled site-specific management of crop inputs for improved yields and quality, precision livestock farming has boosted efficiencies in animal and dairy industries. By 2020, highly automated systems are employed in crop and animal agriculture to increase input efficiency and agricultural output with reduced adverse impact on the environment. Ground and aerial robots combined with artificial intelligence (AI) techniques …

Impact Of Direction Parameter In Performance Of Modified Aodv In Vanet, Afsana Ahamed, Hamid Vakilzadian

Department of Electrical and Computer Engineering: Faculty Publications

A vehicular ad hoc network (VANET) is a technology in which moving cars are used as routers (nodes) to establish a reliable mobile communication network among the vehicles. Some of the drawbacks of the routing protocol, Ad hoc On-Demand Distance Vector (AODV), associated with VANETs are the end-to-end delay and packet loss. We modified the AODV routing protocols to reduce the number of route request (RREQ) and route reply (RREP) messages by adding direction parameters and two-step filtering. The two-step filtering process reduces the number of RREQ and RREP packets, reduces the packet overhead, and helps to select the stable …

Ultrafast Optical Response And Ablation Mechanisms Of Molybdenum Disulfide Under Intense Femtosecond Laser Irradiation, Changji Pan, Lan Jiang, Jingya Sun, Qingsong Wang, Feifei Wang, Ka Wang, Yongfeng Lu, Yeliang Wang, Liangti Qu, Tianhong Cui

Department of Electrical and Computer Engineering: Faculty Publications

Numerous valuable studies on electron dynamics have focussed on the extraordinary properties of molybdenum disulfide (MoS2); however, most of them were confined to the level below the damage threshold. Here the electron dynamics of MoS2 under intense ultrafast laser irradiation was investigated by experiments and simulations. Two kinds of ablation mechanisms were revealed, which led to two distinct types of electron dynamics and final ablation morphology. At a higher fluence, the emergence of superheated liquid induced a dramatic change in the transient reflectivity and micro-honeycomb structures. At a lower fluence, the material was just removed by sublimation, and the ablation …

The Covid-19 Pandemic And Transportation Engineering, Chris Hendrickson,, Laurence Rilett

Department of Civil and Environmental Engineering: Faculty Publications

The COVID-19 pandemic has been an enormous global disruption with immense economic, environmental, and social impacts throughout the world. Only world wars and the flu pandemic of 1918 are comparable in the wide range of consequences, including fatalities, over a relatively short period of time. Unfortunately, we can expect other major disruptions to occur in the future. In this editorial, we intend to discern some lessons for the transportation engineering profession that can be learned from the current catastrophe that can help us prepare for future disruptions. We will ignore nontransportation aspects of the pandemic such as the development of …

Experimental Study On The Characteristics Of Formation And Dissociation Of Co2 Hydrates In Porous Media, Amin Hosseini Zadeh, Ijung Kim, Seunghee Kim

Department of Civil and Environmental Engineering: Faculty Publications

Geologic carbon sequestration (GCS) has pursued as a feasible strategy to store the large amount of CO₂ to curb its emission to the atmosphere in an effort to mitigate the greenhouse effects. CO₂ hydrate, which can form when the pressure and temperature satisfy its stability condition, can provide a self-trapping mechanism for an offshore CO₂ geologic storage. For example, direct sequestration of CO₂ in the form of hydrate cystals an be achieved in the storage zone an potentially provide a secondary caprock. These application, however, require a thorough understanding of the formation and dissociation of CO …

An Experiential Online Training Approach For Underrepresented Engineering And Technology Students, Arefeh Mohammadi, Kevin Grosskopf, John Killingsworth

Durham School of Architectural Engineering and Construction: Faculty Publications

Workforce pipelines are essential to sustain a productive workforce in an increasingly competitive, high-tech environment. Advanced automation, sensors, materials and data analytics will increase the need for highly skilled workers in the manufacturing (and manufactured construction) sector. Attracting and developing the next-generation workforce is not without its challenges; however, students are often deficient in technical skills and generally have negative perceptions about manufacturing and construction. As a result, new education and training models have been developed to provide instruction at all levels of the educational system, with a focus on both traditional students and non-traditional students, including ethnic minorities, women, …

Evaluation Of An Interview-Based Internship Class In The Construction Management Curriculum: A Case Study Of The University Of Nebraska-Lincoln, Ali Karji, Stuart Bernstein, Mohammadsoroush Tafazzoli, Arash Arash Taghinezhad, Arefeh Mohammadi

Department of Construction Engineering and Management: Faculty Publications

Internships have been shown to be impactful tools to connect students’ learning in academia with real-world industrial needs. To help the students to get more out of their internship experience, some universities provide a summer internship class in which students do class assignments based on their experiences during their internship. There have been numerous studies on the benefits of internships. However, the benefits of a potential internship class for students in construction management (CM) programs at universities have not yet been investigated. This paper demonstrates the structure of an interview-based internship class and investigates its effectiveness. We have focused on …

Global Technology Economic Analysis Paradigm, Iwasan D. Kejawa Ed.D

School of Computing: Faculty Publications

Abstract

Is true that it is not only the consumers that make the economy prospers? Business and government also play a role in the economy of a country and corporation. “The GLOBAL technology economy is driven perhaps by the example of a consumer-based society and capital driven citizenry," according to the article in the investor guide of 2013. The role of the government is very important in businesses, organizations and consumers alike depending on the decisions made by the government officials spending of the government. Research have indicated that dependencies of government, organizations, businesses and consumers are intertwine or intermediary. …

Far-Field Transient Absorption Nanoscopy With Sub-50 Nm Optical Super-Resolution, Yali Bi, Chi Yang, Lei Tong, Haozheng Li, Boyu Yu, Shuai Yan, Guang Yang, Meng Deng, Yi Wang, Wei Bao, Lei Ye, Ping Wang

Department of Electrical and Computer Engineering: Faculty Publications

Nanoscopic imaging or characterizing is the mainstay of the development of advanced materials. Despite great progress in electronic and atomic force microscopies, label-free and far-field characterization of materials with deep sub- wavelength spatial resolution has long been highly desired. Herein, we demonstrate far-field super-resolution transient absorption (TA) imaging of two-dimensional material with a spatial resolution of sub-50 nm. By introducing a donut- shaped blue saturation laser, we effectively suppress the TA transition driven by near-infrared (NIR) pump–probe photons, and push the NIR-TA microscopy to sub-diffraction-limited resolution. Specifically, we demonstrate that our method can image the individual nano-grains in graphene with …

Precursor-Surface Interactions Revealed During Plasma-Enhanced Atomic Layer Deposition Of Metal Oxide Thin Films By In-Situ Spectroscopic Ellipsometry, Ufuk Kilic, Alyssa Mock, Derek Sekora, Simeon Gilbert, Shah R. Valloppilly, Natale J. Ianno, Marjorie Langell, Eva Schubert, Mathias Schubert

Department of Electrical and Computer Engineering: Faculty Publications

We find that a five-phase (substrate, mixed native oxide and roughness interface layer, metal oxide thin film layer, surface ligand layer, ambient) model with two-dynamic (metal oxide thin film layer thickness and surface ligand layer void fraction) parameters (dynamic dual box model) is sufficient to explain in-situ spectroscopic ellipsometry data measured within and across multiple cycles during plasma-enhanced atomic layer deposition of metal oxide thin films. We demonstrate our dynamic dual box model for analysis of in-situ spectroscopic ellipsometry data in the photon energy range of 0.7–3.4 eV measured with time resolution of few seconds over large numbers of cycles …

Transcriptional Analysis Of Cleft Palate In Tgfβ3 Mutant Mice, J. Liu, S.K. Chanumolu, K.M. White, M. Albahrani, Hasan H. Otu, A. Nawshad

Department of Electrical and Computer Engineering: Faculty Publications

Cleft palate (CP) is one of the most common craniofacial birth defects, impacting about 1 in 800 births in the USA. Tgf-β3 plays a critical role in regulating murine palate development, and Tgf-β3 null mutants develop cleft palate with 100% penetrance. In this study, we compared global palatal transcriptomes of wild type (WT) and Tgf-β3 −/− homozygous (HM) mouse embryos at the crucial palatogenesis stages of E14.5, and E16.5, using RNA-seq data. We found 1,809 and 2,127 differentially expressed genes at E16.5 vs. E14.5 in the WT and HM groups, respectively (adjusted p < 0.05; |fold change|> 2.0). We focused on the genes that …

Scalable Universalspace Vector Pulse Width Modulation Scheme For Multilevel Inverters, Wei Qiao, Fa Chen, Liyan Qu

Department of Electrical and Computer Engineering: Faculty Publications

A scalable universal space vector pulse-width modulation (SVPWM) scheme for multilevel inverters is disclosed. In the disclosed SVPWM scheme, the modulation triangle is quickly identified based on a coordinate transformation from an a-ß coordinate system to a 120° oblique coordinate system. Then, the duty cycles and switching states of the three vertices of the modulation triangle are determined by simple algebric computations. In a switching period, any vertex of the modulation triangle can be flexibly selected as the start point to optimize the switching sequence with flexibly adjustable duty cycles(s) for the redundant switching state(s) according to specific applications.

Detecting Faults In Wind Turbines, Wei Qiao, Xiang Gong

Department of Electrical and Computer Engineering: Faculty Publications

A wind turbine generator faultdetection method is described.The method includes acquiring curent data from a wind turbine generator during operation, determining frequency demodulated signals and amplitude demodulated signals by frequency demodulating and amplitude demodulating the current data, resampling the frequency and amplitude demodulated signals corresponding to the current data, monitoring a frequency spectra of the resampled frequency and amplitude demodulated signals corresponding to the current data to identify one or more excitations in the frequency spectra. In response to identifying one or more excitations in the frequnecy spectra at one or more of the variable fault characteristic frequecies, the method …

Long-Term Tracking Of Group-Housed Livestock Using Keypoint Detection And Map Estimation For Individual Animal Identification, Eric T. Psota, Ty Schmidt, Benny Mote, Lance C. Pérez

Department of Electrical and Computer Engineering: Faculty Publications

Tracking individual animals in a group setting is a exigent task for computer vision and animal science researchers. When the objective is months of uninterrupted tracking and the targeted animals lack discernible differences in their physical characteristics, this task introduces significant challenges. To address these challenges, a probabilistic tracking-by-detection method is proposed. The tracking method uses, as input, visible keypoints of individual animals provided by a fully-convolutional detector. Individual animals are also equipped with ear tags that are used by a classification network to assign unique identification to instances. The fixed cardinality of the targets is leveraged to create a …

Ieee Access Special Section Editorial: Security And Privacy For Cloud And Iot, Kuo-Hui Yeh, Weizhi Meng, Sk Hafizul Islam, Kuan Zhang, Ennan Zhai

Department of Electrical and Computer Engineering: Faculty Publications

No abstract provided.

Ieee Access Special Section Editorial: Energy Management In Buildings, Kun Wang, Yi Qian, Joel J.P.C. Rodrigues, Fei Richard Yu, Peng Li

Department of Electrical and Computer Engineering: Faculty Publications

No abstract provided.