Engineering Commons^™

Access Management Implementation In Kentucky – Technical Support Document And Status Report, Barry House

Kentucky Transportation Center Research Report

This report describes the efforts of the Kentucky Transportation Cabinet’s Access Management Implementation Task Force. The task force was established in May 2004 and was charged with the responsibility of reviewing and refining the recommendations in the Access Management for Kentucky research study for the purpose of implementing a comprehensive access management program for the state of Kentucky. The Kentucky Transportation Center provided technical and administrative support to the task force. This report provides documentation of the information considered by the task force, the deliberations over that information, and the decisions and recommendations made by the task force. Although a …

Evaluation Of 70 Mph Speed Limit In Kentucky, Kenneth R. Agent

Kentucky Transportation Center Research Report

The objective of this study was to document the change in operating speeds of cars and trucks on rural interstates and parkways as a result of the change in speed limit from 65 mph to 70 mph. The 85th percentile speed increased 1.3 mph for cars (74.6 to 75.9 mph) and 0.6 mph for trucks (69.8 to 70.4 mph) on rural interstates and 2.0 mph for cars (73.5 to 75.5 mph) and 1.2 mph for trucks (69.5 to 70.7 mph) on four-lane parkways. The increase in speed limits on a limited number of roads did not result in an increase …

Low-Cost Safety Measures At Signalized Intersections, Kenneth R. Agent

Kentucky Transportation Center Research Report

The objectives of this study were to: a) identify intersections with a high number of crashes involving a driver disregarding the traffic signal, b) identify types of low-cost safety measures which may be used as a countermeasure for red light running, and c) evaluate the effectiveness of the installation of some of these countermeasures at a sample of high-crash intersections. Low-cost countermeasures such as double-red signal heads and retro-reflective backplates were installed at locations either identified as a high-crash location or by district traffic engineers. Crashes decreased at these locations with a positive public response. The investigation warrants additional use …

Evaluation Of Pavement Marking Performance, Eric R. Green, Kenneth R. Agent

Kentucky Transportation Center Research Report

The objective of the investigation was to evaluate the useful life of pavement markings. The Manual on Uniform Traffic Control Devices (MUTCD) provides general guidelines for the application and installation of pavement markings. However, performance requirements for various types of pavement markings are not included. Retroreflectivity data were collected throughout Kentucky on various longitudinal pavement markings using mobile and manual techniques. Data were collected on two-year old and one-year old lines. The retroreflectivity levels were analyzed and the several recommendations were made. Minimum levels of retroreflectivity should be set for determining what roads to restripe annually. These values should be …

Poster Session, Kentucky Water Resources Research Institute, University Of Kentucky

Kentucky Water Resources Annual Symposium

• Kentucky Water Awareness Month Packet, Ashley Osborne, UK Cooperative Extension Service, ENRI Task Force
• Recent Enhancements to the Kentucky Groundwater-Quality Data Search Engine, Bart Davidson and R. Stephen Fisher, KGS
• Diatom Colonization Patterns and Carbon Stable Isotopic Ratios in Developing Periphyton at Springs of Differing Geologic Origin in Land-Between-the-Lakes, Courtney Snapp and Susan Hendricks, Water Sciences Program, Murray State University
• Seasonal Changes in Stratification and Oxygen Content of a Eutrophic Lake, Wilgreen Lake, Madison County, Kentucky, Jill Hunter and Walter Borowski, Dept of Geography and Geology, EKU
• Water Pioneers Water Quality Program 2007, Stephanie Jenkins, …

Session 2d: Pathogen Transport, Kentucky Water Resources Research Institute, University Of Kentucky

Kentucky Water Resources Annual Symposium

• Assessment of Nonpoint Source Impacts on Groundwater Quality in South Elkhorn Creek Basin, Central Kentucky, Robert J. Blair and others, Kentucky Division of Water, Frankfort
• Karst Groundwater Infiltration of the Sanitary Sewer within the Beargrass Creek Watershed, Jefferson County, Kentucky, Joseph Ray and others, Kentucky Division of Water
• Illicit Discharge into Town Branch in Lexington, Kentucky, Jim Buckles and others, Tetra Tech, Lexington
• Assessment of Water Quality Trends in the Upper Forks of the Kentucky River Basin: Focus on Pathogen Impairment, Chandramouli Viswanathan, Kentucky Water Resources Research Institute, UK

Session 2c: Water Quality, Kentucky Water Resources Research Institute, University Of Kentucky

Kentucky Water Resources Annual Symposium

• Determinations of Bioavailable Fractions in the Assessment of Metals in Big and Little Bayou Creeks……, McCracken County, Kentucky, David J. Price, Dept Biology, UK
• Creation of a Catalog of Environmental Mercury Databases in Kentucky, Caroline Chan and others, School of Public Health and Information Sciences, U of L
• Using Nitrogen Isotopes to Trace Nutrient Inputs to a Eutrophic Lake, Wilgreen Lake, Madison County, Kentucky, Walter Borowski and Theresa Aguiar, Dept of Geography and Geology, EKU
• Using Microbial Distribution and Abundance in a Eutrophic Lake as a Tracer for Nutrient Inputs, Wilgreen Lake, Madison County Kentucky, Theresa …

Session 2b: Variety, Kentucky Water Resources Research Institute, University Of Kentucky

Kentucky Water Resources Annual Symposium

• Mud, Horses and Clean Water – A BMP Demonstration Project for Suburban Horse Owners, Steve Higgins and others, Biosystems and Ag Engineering, UK
• A Topological Model of Open Channel Flows, Brian Belcher and Jimmy Fox, Dept of Civil Engineering, UK
• Rain Gardens: Restoring a Waste Water to a Priceless Treasure, H. David Gabbard, LFUCG, Richard Walker, Tetra Tech, and Sandy Camargo, CDP Engineers
• Kentucky Erosion Prevention and Sediment Control (KESPSC) – An Answer to the Question “What is a Qualified Inspector?” Shelby Jett, Kentucky Transportation Cabinet, Kevin Gibson and John Ricketts, Stantec Consulting Services, Lexington

Session 2a: Groundwater, Kentucky Water Resources Research Institute, University Of Kentucky

Kentucky Water Resources Annual Symposium

• How Close Do We Need to Sample for Appropriate Solute Transport Characterization Through the Vadose Zone? Ole Wendroth and others, Dept of Plant and Soil Sciences, UK
• Efficiently Locating and Repairing Damaged Sewer Lines in a Karst Terrane, Kevin Lyne, LFUCG and Robert Blair, KDOW
• Hydrogeologic Investigations of Pavement Subsidence in the Cumberland Gap Tunnel, Jim Dinger and others, KGS

Session 1d: Land Use, Kentucky Water Resources Research Institute, University Of Kentucky

Kentucky Water Resources Annual Symposium

• Mountaintop Mining and Sustainable Development Opportunities for Appalachia, J. Stephen Gardner, Engineering Consulting Services, Inc., Lexington
• Spatial Characterization of Kentucky’s 2005-2001 Land Cover Change, A Kentucky Landscape Census Product, Demetrio Zourarakis and others, Kentucky Division of Geographic Information
• Feasibility Study of Cover-Collapse Rate in the Western Pennyroyal Karst of Kentucky, James Currens and Randall Paylor, KGS
• Kentucky SPARROW Model and its Applications to Understanding Nutrient Loads, Tanja N. Williamson, USGS Kentucky Water Science Center

Session 1c: Student Research Projects, Kentucky Water Resources Research Institute, University Of Kentucky

Kentucky Water Resources Annual Symposium

• A 3-D Computational Fluid Dynamics Code for Simulation of Pump Stations with Vertical Plunging Jet and Air Bubble Transport, Tien Mun Yee and Scott Yost, Dept of Civil Engineering, UK
• Chemical Evolution of Groundwater in the Wilcox Aquifer of the Mississippi Embayment, Estifanos Haile and Alan Fryar, Dept of Earth and Environmental Sciences, UK
• Sediment Organic Matter Degradation within Storage Zones Deposited In-Stream, Charles Davis and Jimmy Fox, Dept of Civil Engineering, UK
• Effectiveness of Improved Skid Trail Headwater Stream Crossings, Jeffrey Stringer and Christopher Reeves, Dept of Forestry, UK

Session 1b: Education, Kentucky Water Resources Research Institute, University Of Kentucky

Kentucky Water Resources Annual Symposium

• Community Based Science, Water Quality and Nonpoint Source Pollution, Carol Hanley and others, Tracy Farmer Center for the Environment, UK
• A Stormwater Education Program to Assist Kentucky’s MS4 Phase II Communities, Yvonne Meichtry and Julie Gee, Kentucky Transportation Cabinet, Frankfort
• Water/Wastewater Technician Training Institute: A Holistic Approach to Developing a Professional Water and Wastewater Workforce, Andrew Ernest, Center for Water Resource Studies, WKU
• Geology for Everyone, New Map Products from the Kentucky Geological Survey, Daniel Carey, KGS

Session 1a: Watersheds, Kentucky Water Resources Research Institute, University Of Kentucky

Kentucky Water Resources Annual Symposium

• Cane Run Watershed Assessment and Restoration Project, Steve Higgins and others, Biosystems and Ag Engineering, UK
• Kentucky Institute for Watershed Management Support, Andrew Ernest, Center for Water Resource Studies, WKU
• Watershed Planning Guidebook for Kentucky Communities, Katie Holmes and others, Kentucky Waterways Alliance

Proceedings Of 2008 Kentucky Water Resources Annual Symposium, Kentucky Water Resources Research Institute, University Of Kentucky

Kentucky Water Resources Annual Symposium

This conference was planned and conducted as part of the state water resources research annual program with the support and collaboration of the Department of the Interior, U.S. Geological Survey and the University of Kentucky Research Foundation, under Grant Agreement Number 06HQGR0087.

The views and conclusions contained in this document and presented at the symposium are those of the abstract authors and presenters and should not be interpreted as necessarily representing the official policies, either expressed or implied, of the U.S. Government or other symposium organizers and sponsors.

Investigation Of Voids/Cracking On The I-275 Twin Bridges Over The Ohio River In Kenton County - Phase I, Brad Rister, Theodore Hopwood Ii

Kentucky Transportation Center Research Report

An evaluation of the northbound bridge approach and the abutment wall of (Combs-Hehl) bridge on I-275 in Kenton County was conducted in September 2007. The inspection consisted of using ground penetrating radar to look for potential voids beneath the concrete approach slab and a video camera inspection to inspect the void space beneath the pier cap/concrete beam in front of the abutment wall.

Results of field testing and recommendations:

A possible void approximately 1-2 inches in depth resides under the approach slab approximately 105 feet before the bridge abutment in the fast lane. It is recommended that this section be …

Evaluation Of Noise Impact Mitigation Protocols To Support Css, Ted Grossardt, Lou Cohn, Al Harris, Keiron Bailey, John Ripy

Kentucky Transportation Center Research Report

This research project developed and evaluated practical ways of involving the public in context sensitive sound mitigation strategies. The integrated use of photo montage, PowerPoint presentation, linked traffic sound files, and audience response systems demonstrated that significant visual and aural differences could be clearly portrayed and clear preferences could be expressed by citizens and professionals alike, even where the choice menu was quite complex.

Lectures On Computational Numerical Analysis Of Partial Differential Equations, James M. Mcdonough

Mechanical Engineering Textbook Gallery

From Chapter 1:

The purpose of these lectures is to present a set of straightforward numerical methods with applicability to essentially any problem associated with a partial differential equation (PDE) or system of PDEs independent of type, spatial dimension or form of nonlinearity.

Evaluation Of The Effectiveness Of Pavement Rumble Strips, Adam Kirk

Kentucky Transportation Center Research Report

This report analyzes the effectiveness of continuous shoulder rumble strips (CSRS) and center line rumble strips (CLRS) on rural two lane roads in Kentucky. This study evaluates the safety benefits, and design details associated with the application of the CSRS and CLRS. The recommended practices proposed as a result of the crash analysis have the potential to reduce both run off the road and opposite direction crashes on rural two lane roads in Kentucky. These recommendations provide benefits for narrow roadways with little to no shoulder as well as larger roadways with wider paved shoulders.

Use Of Edge Line Markings On Rural Two-Lane Highways, Kenneth R. Agent, Eric R. Green

Kentucky Transportation Center Research Report

The objective of this study was to review roadway characteristics and crash data in Kentucky and determine if revisions should be made to current guidelines for the use of edge lines. Recommendations were made concerning the use of edge lines, centerlines, and paved shoulders on rural, two-lane roadways with varying pavement widths.

Gas Sensing Properties And Transport Properties Of Multi Walled Carbon Nanotubes, Raghu Mangu

University of Kentucky Master's Theses

Multi walled carbon nanotubes (MWCNT) grown in highly ordered porous alumina templates were incorporated into a resistive gas sensor design and were evaluated for their sensitivities. The material characteristics and electrical properties of the nanotubes were analyzed. A study was undertaken to elucidate the effect of UV light on desorption characteristics and the dependence of sensitivity on (i) thickness of amorphous carbon layers and (ii) flow rates of analyte gases. These sensors were highly responsive to both oxidizing and reducing gases with steady state sensitivities of 5% and 10% for 100ppm of NH₃ and NO₂ respectively, at room …

Modular Fast Direct Analysis Using Non-Radiating Local-Global Solution Modes, Xin Xu

University of Kentucky Doctoral Dissertations

This dissertation proposes a modular fast direct (MFD) analysis method for a class of problems involving a large fixed platform region and a smaller, variable design region. A modular solution algorithm is obtained by first decomposing the problem geometry into platform and design regions. The two regions are effectively detached from one another using basic equivalence concepts. Equivalence principles allow the total system model to be constructed in terms of independent interaction modules associated with the platform and design regions. These modules include interactions with the equivalent surface that bounds the design region. This dissertation discusses how to analyze (fill …

Novel Catalysts For The Production Of Co- And Co2-Free Hydrogen And Carbon Nanotubes By Non-Oxidative Dehydrogenation Of Hydrocarbons, Wenqin Shen

University of Kentucky Doctoral Dissertations

Non-oxidative dehydrogenation of hydrocarbons is an attractive alternative route for the production of CO- and CO₂-free hydrogen. It will satisfy a major requirement for successful utilization of polymer electrolyte membrane (PEM) fuel cells (< 10 ppm CO) and sequestering carbon as a potentially valuable by-product, carbon nanotubes (CNTs). Due to the deposition of carbon on the surface of catalyst particles during the reaction, catalyst performance, life-time, and purification of the generated carbon product, are significant issues to solve in order to make the process practically feasible. The scope of this thesis includes: the development of novel Fe, Ni, and Fe-Ni catalysts supported on a Mg(Al)O support to achieve improved catalytic performance with easily-purified CNTs; evaluation of catalysts for ethane/methane dehydrogenation at moderate reaction temperatures; and study of activation and deactivation mechanisms by a variety of characterization techniques including TEM, HRTEM, XRD, Mössbauer spectroscopy, and x-ray absorption fine structure (XAFS) spectroscopy. The Mg(Al)O support was prepared by calcination of synthetic MgAl-hydrotalcite with a Mg to Al ratio of 5. The catalysts were prepared either by conventional incipient wetness method or by a novel nanoparticle impregnation method, where the monodisperse catalyst nanoparticles were prepared in advance by thermal decomposition of a metal-organic complex in an organic-phase solution and then dispersed onto the Mg(Al)O support. Dehydrogenation of undiluted methane was conducted in a fix-bed plug-flow reactor. Before reaction, the catalysts were activated by reduction in hydrogen. Fe-based catalysts exhibit a higher hydrogen yield at temperature above 600ºC compared with monometallic Ni catalyst. FeNi-9 nm/Mg(Al)O, Fe-10 nm/Mg(Al)O and Fe-5 nm/ Mg(Al)O nanoparticle catalysts show much improved performance and longer life-times compared with the corresponding FeNi IW/Mg(Al)O and Fe IW/Mg(Al)O catalysts prepared by incipient wetness. 10 nm is the optimum particle size for methane dehydrogenation. Addition of Ni to Fe forming a bimetallic FeNi alloy catalyst enhances the catalytic performance at the temperatures below 650ºC. Metallic Fe, Ni, FeNi alloy and Fe-Ni-C alloy, unstable iron carbide are all catalytically active components. Catalysts deactivation is due to the carbon encapsulation. The carbon products are in the form of stack-cone CNTs (SCNTs) and multi-walled CNTs (MWNTs), depending on the reaction temperature and catalyst composition. The growth of CNTs follows a tip growth mechanism and the purity of cleaned CNTs is more than 99.5%.

Efficient And Scalable Network Security Protocols Based On Lfsr Sequences, Saikat Chakrabarti

University of Kentucky Doctoral Dissertations

The gap between abstract, mathematics-oriented research in cryptography and the engineering approach of designing practical, network security protocols is widening. Network researchers experiment with well-known cryptographic protocols suitable for different network models. On the other hand, researchers inclined toward theory often design cryptographic schemes without considering the practical network constraints. The goal of this dissertation is to address problems in these two challenging areas: building bridges between practical network security protocols and theoretical cryptography. This dissertation presents techniques for building performance sensitive security protocols, using primitives from linear feedback register sequences (LFSR) sequences, for a variety of challenging networking applications. …

An Investigation Of Size Effects On Thin Sheet Formability For Microforming Applications, Nasr Abdelrahman Shuaib

University of Kentucky Doctoral Dissertations

The increasing demand for powerful miniaturized products for all industrial applications has prompted the industry to develop new and innovative manufacturing processes to fabricate miniature parts. One of the major challenges facing the industry is the dynamic market which requires continuous improvements in design and fabrication techniques. This means providing products with complex features while sustaining high functionality. As a result, microfabrication has gained a wide interest as the technology of the future, where tabletop machine systems exist. Microforming processes have the capability of achieving mass production while minimizing material waste. Microforming techniques can produce net-shape products with intricacy in …

Surfactant And Metal Sorption Studies By Functionalized Membranes And Quartz Crystal Microbalance, Abhay R. Ladhe

University of Kentucky Doctoral Dissertations

Functionalized membranes provide an elegant platform for selective separations and sorptions. In this dissertation, application of functionalized membranes for surfactant and metal sorption studies are discussed. Sorption behavior of surfactants is also studied using quartz crystal microbalance (QCM) and other techniques.

Adsorption of the ethoxylated surfactants on polymeric materials (cotton and polyester) and model gold surface was quantified from a non-aqueous siloxane based solvent (D5) and water. The role of ethylene oxide group and the effect of nature of polymeric materials on adsorption behavior was quantified and established. In the case of gold-water interface, the adsorption data was fitted to …

Linking The Structure And Mechanical Behavior Of Nanoporous Gold, Ye Sun

University of Kentucky Doctoral Dissertations

The structure of nanoporous gold (np-Au) provides a very limited volume for deformation to occur, and thus offers an opportunity to study the role of defects such as dislocations in nanoscale metal volumes. A practical goal is to understand mechanical properties of np-Au so that it can be can produced in stable form, for use in applications that require some mechanical integrity. Bulk and thin film np-Au have been fabricated and studied here.

Bulk np-Au was prepared by electrochemically dealloying Au-Ag alloys with 25 and 30 at.% Au. In the lower Au content material, cracks always formed during dealloying. When …

Kentucky Water Resources Research Institute Annual Technical Report Fy 2007, Kentucky Water Resources Research Institute, University Of Kentucky

KWRRI Annual Technical Reports (USGS’s 104b Grant Program)

The 2007 Annual Technical Report for Kentucky consolidates reporting requirements of the Section 104(b) base grant award into a single document that includes: 1) a synopsis of each student research enhancement project conducted during the period, 2) citations for related publications, reports, and presentations, 3) a description of information transfer activities, 4) a summary of student support during the reporting period, and 5) notable awards and achievements during the year.

Photovoltaic Cells Based On Copper Phthalocyanine And Cadmium Sulfide Heterojunction, Sandeep Kumar Marda

University of Kentucky Master's Theses

This work focuses on the solar cell based on the heterostructure formed between Copper Phthalocyanine (CuPc) and Cadmium Sulfide (CdS). Two different fabrication techniques were used for depositing the organic and inorganic layers of CuPc and CdS layers respectively. CuPc was deposited by electrodeposition while CdS was deposited by chemical bath deposition. Hybrid CdS/CuPc thin films were obtained from CdS films grown on Glass/ITO by chemical bath deposition followed by electrodeposition of CuPc onto these films and annealing at 250˚C after the deposition of each layer. The maximum open circuit voltage (V_oc) and the short circuit current density …

Packing Factors Of Feed Products In Storage Structures, Samuel G. Mcneill, Michael D. Montross, Sidney A. Thompson, I. Joseph Ross, Thomas C. Bridges

Biosystems and Agricultural Engineering Faculty Publications

Experiments were conducted to measure the changes in bulk density of cracked corn, corn meal, soybean meal, cotton seed meal, and distillers dried grain (without solubles) when subjected to simulated overburden pressures. All materials were tested at two moisture content levels (approximately 8% and 12% w.b.) and seven pressures between 0 and 69 kPa (0 and 10 psi). A mathematical model was fitted to the data to predict the bulk density of each feed ingredient as a function of pressure and moisture content. These relationships were inserted into a previously developed computer model to predict ingredient packing within conventional storage …

Airflow Resistance Of Wheat Bedding As Influenced By The Filling Method, J. Łukaszuk, M. Molenda, J. Horabik, B. Szot, Michael D. Montross

Biosystems and Agricultural Engineering Faculty Publications

A study was conducted to estimate the degree of variability of the airflow resistance in wheat caused by the filling method, compaction of the sample, and airflow direction. Two types of grain chambers were used: a cylindrical column 0.95 m high and 0.196 m in diameter, and a cubical box of 0.35 m side. All factors examined were found to influence considerably the airflow resistance. Gravitational axial filling of the grain column from three heights (0.0, 0.95 and 1.8 m) resulted in the pressure drops of 1.0, 1.3, and 1.5 kPa at the airflow velocity of 0.3 m/s. Consolidation of …