Engineering Commons^™

Emerging Computing Based Novel Solutions For Design Of Low Power Circuits, Azhar Mohammad

Theses and Dissertations--Electrical and Computer Engineering

The growing applications for IoT devices have caused an increase in the study of low power consuming circuit design to meet the requirement of devices to operate for various months without external power supply. Scaling down the conventional CMOS causes various complications to design due to CMOS properties, therefore various non-conventional CMOS design techniques are being proposed that overcome the limitations. This thesis focuses on some of those emerging and novel low power design technique namely Adiabatic logic and low power devices like Magnetic Tunnel Junction (MTJ) and Carbon Nanotube Field Effect transistor (CNFET). Circuits that are used for large …

Energy-Efficient And Secure Hardware For Internet Of Things (Iot) Devices, Dinesh Kumar Selvakumaran

Theses and Dissertations--Electrical and Computer Engineering

Internet of Things (IoT) is a network of devices that are connected through the Internet to exchange the data for intelligent applications. Though IoT devices provide several advantages to improve the quality of life, they also present challenges related to security. The security issues related to IoT devices include leakage of information through Differential Power Analysis (DPA) based side channel attacks, authentication, piracy, etc. DPA is a type of side-channel attack where the attacker monitors the power consumption of the device to guess the secret key stored in it. There are several countermeasures to overcome DPA attacks. However, most of …

Validating Spray Coverage Rate Using Liquid Mass On A Spray Card, Michael P. Sama, Austin M. Weiss, Emma K. Benedict

Biosystems and Agricultural Engineering Faculty Publications

Validation of agricultural sprayers is important for quantifying as-applied coverage rates under field conditions. The complexity of modern sprayer control systems presents a challenge for precise field validation due to the use of nozzle control technologies, such as pulse width modulation, to meter chemical flow rates at individual nozzles. Non-uniform flow over time may result in local variations at high spatial resolutions that are ignored when estimating as-applied coverage rates across a field. The purpose of this study was to test several methods for estimating the mass of water applied to a water-sensitive paper spray card target using steady-state and …

Application Of Acoustic Emission And Machine Learning To Detect Codling Moth Infested Apples, Mengxing Li, Nader Ekramirad, Ahmed Rady, Akinbode A. Adedeji

Biosystems and Agricultural Engineering Faculty Publications

Incidence of codling moth (CM) (Cydia pomonella L.) infestation in apples has been a major concern in North America for decades. CM larvae bore deep into the fruit, making it unmarketable. An effective noninvasive method to detect larvae-infested apples is necessary to ensure that apples are CM-free in post-harvest processing. In this study, a novel approach using an acoustic emission (AE) system and subsequent machine learning methods was applied to classify larvae-infested apples from intact apples. 'GoldRush‘ apples were infested with CM neonates and stored at the same conditions as intact apples. The AE system was used to collect …

Hydraulic Properties Of Baled Switchgrass And Miscanthus, Drew F. Schiavone, Michael D. Montross

Biosystems and Agricultural Engineering Faculty Publications

This study characterized the hydraulic properties within baled switchgrass ( Panicum virgatum L., variety Alamo) and miscanthus (Miscanthus x giganteus), thereby enabling a better understanding of moisture changes in baled biomass during on-farm storage and/or high-solids bioconversion. Fully saturated bales were drained by gravity, and the moisture content was determined over 60 h. The average initial moisture content ranged between 55.9% and 71.9% (w.b.) for switchgrass and between 60.5% and 73.9% (w.b.) for miscanthus bales depending on the dry bale density. As the bale drained by gravity, rapid leaching of water was observed within the first 0.1 h, …

Improving In-Stream Nutrient Routines In Water Quality Models Using Stable Isotope Tracers: A Review And Synthesis, Alexandria K. Jensen, William I. Ford, James F. Fox, Admin Husic

Biosystems and Agricultural Engineering Faculty Publications

Water quality models serve as an economically feasible alternative to quantify fluxes of nutrient pollution and to simulate effective mitigation strategies; however, their applicability is often questioned due to broad uncertainties in model structure and parameterization, leading to uncertain outputs. We argue that reduction of uncertainty is partially achieved by integrating stable isotope data streams within the water quality model architecture. This article outlines the use of stable isotopes as a response variable within water quality models to improve the model boundary conditions associated with nutrient source provenance, constrain model parameterization, and elucidate shortcomings in the model structure. To assist …

Two Essays On Whole Farm Modeling And Crop Marketing In Western Kentucky, Benjamin A. Martin

Theses and Dissertations--Agricultural Economics

This thesis is composed of two essays that investigate whole farm planning and crop marketing in western Kentucky. In the first essay, contracting decisions between food corn producers and a mill are analyzed to observe factors affecting the bushel amount farmers contract. Unbalanced panel data containing seven years’ worth of pricing and contract information are used with a fixed-effects model to generate parameter estimates and quantify their effect on bushels contracted. It was found that contract attributes, market condition, and relationship-specific assets had a significant effect on producers’ food corn contracting decisions. The second essay utilizes mixed-integer programming to optimize …

Nanoparticle Orientation To Control Rna Loading And Ligand Display On Extracellular Vesicles For Cancer Regression, Fengmei Pi, Daniel W. Binzel, Tae Jin Lee, Zhefeng Li, Meiyan Sun, Piotr G. Rychahou, Hui Li, Farzin Haque, Shaoying Wang, Carlo M. Croce, Bin Guo, B. Mark Evers, Peixuan Guo

Markey Cancer Center Faculty Publications

Nanotechnology offers many benefits, and here we report an advantage of applying RNA nanotechnology for directional control. The orientation of arrow-shaped RNA was altered to control ligand display on extracellular vesicle membranes for specific cell targeting, or to regulate intracellular trafficking of small interfering RNA (siRNA) or microRNA (miRNA). Placing membrane-anchoring cholesterol at the tail of the arrow results in display of RNA aptamer or folate on the outer surface of the extracellular vesicle. In contrast, placing the cholesterol at the arrowhead results in partial loading of RNA nanoparticles into the extracellular vesicles. Taking advantage of the RNA ligand for …

Real-Time Image Pattern Sensor For Weld Pool Penetration Through Reflection In Gtaw, Yu-Ting Chen

Theses and Dissertations--Electrical and Computer Engineering

In gas tungsten arc welding (GTAW), weld pool surface contains crucial information for welding development. In this research, simulate skilled welders to control the welding process and determine the penetration stages based on the weld pool reaction.

This study focuses on solving the uncertainty of the liquid weld pool in joint bases. The weld pool penetration process is highly depending on how the weld pool surface shape. To observe the weld pool, reflect the weld pool surface by the laser and image on the shield glass. The experiments show that the penetration can’t be determine by the reflecting grayness due …

Design Of A Machine Vision Camera For Spatial Augmented Reality, Matt Phillip Ruffner

Theses and Dissertations--Electrical and Computer Engineering

Structured Light Imaging (SLI) is a means of digital reconstruction, or Three-Dimensional (3D) scanning, and has uses that span many disciplines. A projector, camera and Personal Computer (PC) are required to perform such 3D scans. Slight variances in synchronization between these three devices can cause malfunctions in the process due to the limitations of PC graphics processors as real-time systems. Previous work used a Field Programmable Gate Array (FPGA) to both drive the projector and trigger the camera, eliminating these timing issues, but still needing an external camera. This thesis proposes the incorporation of the camera with the FPGA SLI …

Economic Operation Of Typical Microgrids, Yuanzhen Guo

Theses and Dissertations--Electrical and Computer Engineering

A microgrid is a subnetwork of power system that consists of a group of distributed energy sources and loads. It is designed to integrate distributed generation, loads, energy storage devices, converters, and monitoring and protection devices. Generally, a successful microgrid could run both in island mode (off-grid) and in grid-connected mode (on-grid), being able to convert between two modes at any time. With continuous development of the power system, distributed renewable generation unit accounts for an increasing proportion, since microgrid could effectively connect these generation units to the main grid, thereby improving the energy efficiency and the energy structure. Microgrid …

A Redundant Monitoring System For Human Welder Operation Using Imu And Vision Sensors, Rui Yu

Theses and Dissertations--Electrical and Computer Engineering

In manual control, the welding gun’s moving speed can significantly influence the welding results and critical welding operations usually require welders to concentrate consistently in order to react rapidly and accurately. However, human welders always have some habitual action which can have some subtle influence the welding process. It takes countless hours to train an experienced human welder. Using vision and IMU sensor will be able to set up a system and allow the worker got more accurate visual feedback like an experienced worker.

The problem is that monitor and measuring of the control process not always easy under a …

Magneto-Optical Properties Of Thin Permalloy Films: A Study Of The Magneto-Optical Generation Of Light Carrying Angular Momentum, Patrick D. Montgomery

Theses and Dissertations--Electrical and Computer Engineering

Magneto-optical materials such as permalloy can be used to create artificial spin- ice (ASI) lattices with antiferromagnetic ordering. Magneto-optical materials used to create diffraction lattices are known to exhibit magnetic scattering at the half- order Bragg peak while in the ground state. The significant drawbacks of studying the magneto-optical generation of OAM using x-rays are cost, time, and access to proper equipment. In this work, it is shown that the possibility of studying OAM and magneto-optical materials in the spectrum of visible light at or around 2 eV is viable. Using spectroscopic ellipsometry it is possible to detect a change …

Self-Image Multimedia Technologies For Feedforward Observational Learning, Nkiruka M. A. Uzuegbunam

Theses and Dissertations--Electrical and Computer Engineering

This dissertation investigates the development and use of self-images in augmented reality systems for learning and learning-based activities. This work focuses on self- modeling, a particular form of learning, actively employed in various settings for therapy or teaching. In particular, this work aims to develop novel multimedia systems to support the display and rendering of augmented self-images. It aims to use interactivity (via games) as a means of obtaining imagery for use in creating augmented self-images. Two multimedia systems are developed, discussed and analyzed. The proposed systems are validated in terms of their technical innovation and their clinical efficacy in …

Stability Analysis And Design Of A Tracking Filter For Variable Frequency Applications, Pranav Aramane

Theses and Dissertations--Electrical and Computer Engineering

The work presented in this thesis is a frequency adaptive tracking filter that can be used in exact tracking of power frequencies and rejection of unwanted harmonics introduced during power disturbances. The power synchronization process includes power converters and other equipment that have many non-linear components that introduce unwanted harmonics. This new design is motivated by the requirement of a filter that can filter all the harmonics and exactly track a rapidly varying fundamental frequency with little time delay and phase error. This thesis analyzes the proposed filter mathematically based on Lyapunov theory and simulations are presented to show the …

Parameters Affecting The Resistivity Of Lp-Ebid Deposited Copper Nanowires, Gabriel Smith

Theses and Dissertations--Electrical and Computer Engineering

Electron Beam Induced Deposition (EBID) is a direct write fabrication process with applications in circuit edit and debug, mask repair, and rapid prototyping. However, it suffers from significant drawbacks, most notably low purity. Work over the last several years has demonstrated that deposition from bulk liquid precursors, rather than organometallic gaseous precursors, results in high purity deposits of low resistivity (LPEBID). In this work, it is shown that the deposits resulting from LP-EBID are only highly conductive when deposited at line doses below 25μC/cm. When the dose exceeds this value, the resulting structure is highly porous providing a poor conductive …

Distribution System Optimization With Integrated Distributed Generation, Sarmad Khaleel Ibrahim

Theses and Dissertations--Electrical and Computer Engineering

In this dissertation, several volt-var optimization methods have been proposed to improve the expected performance of the distribution system using distributed renewable energy sources and conventional volt-var control equipment: photovoltaic inverter reactive power control for chance-constrained distribution system performance optimisation, integrated distribution system optimization using a chance-constrained formulation, integrated control of distribution system equipment and distributed generation inverters, and coordination of PV inverters and voltage regulators considering generation correlation and voltage quality constraints for loss minimization. Distributed generation sources (DGs) have important benefits, including the use of renewable resources, increased customer participation, and decreased losses. However, as the penetration level …

Stability Improvements For Generalized Average-Value Model Of Dc-Dc Converters, Mahsen Salah Al-Ani

Theses and Dissertations--Electrical and Computer Engineering

Power electronics have a significant role in modern electrical devices, for instance, hybrid electric vehicles. Power electronics are the technology in between the source and the load circuits and can convert the power from dc to ac or from dc to ac. There are also many types of dc-dc converters, like such as boost and buck converters, which exhibit switching ripple behavior. A boost converter increases the output voltage (with respect to the input voltage) and reduces the output current. A buck converter decreases the output voltage and increases the output current. Many models are used to predict the behavior …

A Fault Location Algorithm For Unbalanced Distribution System Without Fault Type Information, Yizhe Li

Theses and Dissertations--Electrical and Computer Engineering

Power system faults normally result in system damage, profit loss and consumer dissatisfaction. Consequently, there is a strong demand on precise and fast fault location estimation for power system to minimize the system restoration time.

This paper examines a method to locate short-circuit faults on a distribution system with unbalanced loads without fault type information. Bus impedance matrix technique was harnessed in the fault location estimation algorithm. The system data including line impedances, source impedance and distribution system layout was assumed to be known factors, hence pre-fault bus impedance can be calculated and implemented into the algorithm. Corresponding methods to …

Intelligent Uav Scouting For Field Condition Monitoring, Hasan Seyyedhasani

Theses and Dissertations--Electrical and Computer Engineering

Precision agriculture requires detailed and timely information about field condition. In less than the short flight time a UAV (Unmanned Aerial Vehicle) can provide, an entire field can be scanned at the highest allowed altitude. The resulting NDVI (Normalized Difference Vegetation Index) imagery can then be used to classify each point in the field using a FIS (Fuzzy Inference System). This identifies areas that are expected to be similar, but only closer inspection can quantify and diagnose crop properties. In the remaining flight time, the goal is to scout a set of representative points maximizing the quality of actionable information …

Speaker And Gender Identification Using Bioacoustic Data Sets, Neenu Jose

Theses and Dissertations--Electrical and Computer Engineering

Acoustic analysis of animal vocalizations has been widely used to identify the presence of individual species, classify vocalizations, identify individuals, and determine gender. In this work automatic identification of speaker and gender of mice from ultrasonic vocalizations and speaker identification of meerkats from their Close calls is investigated. Feature extraction was implemented using Greenwood Function Cepstral Coefficients (GFCC), designed exclusively for extracting features from animal vocalizations. Mice ultrasonic vocalizations were analyzed using Gaussian Mixture Models (GMM) which yielded an accuracy of 78.3% for speaker identification and 93.2% for gender identification. Meerkat speaker identification with Close calls was implemented using Gaussian …

High-Order Integral Equation Methods For Quasi-Magnetostatic And Corrosion-Related Field Analysis With Maritime Applications, Robert Pfeiffer

Theses and Dissertations--Electrical and Computer Engineering

This dissertation presents techniques for high-order simulation of electromagnetic fields, particularly for problems involving ships with ferromagnetic hulls and active corrosion-protection systems.

A set of numerically constrained hexahedral basis functions for volume integral equation discretization is presented in a method-of-moments context. Test simulations demonstrate the accuracy achievable with these functions as well as the improvement brought about in system conditioning when compared to other basis sets.

A general method for converting between a locally-corrected Nyström discretization of an integral equation and a method-of-moments discretization is presented next. Several problems involving conducting and magnetic-conducting materials are solved to verify the accuracy …

Affect-Preserving Visual Privacy Protection, Wanxin Xu

Theses and Dissertations--Electrical and Computer Engineering

The prevalence of wireless networks and the convenience of mobile cameras enable many new video applications other than security and entertainment. From behavioral diagnosis to wellness monitoring, cameras are increasing used for observations in various educational and medical settings. Videos collected for such applications are considered protected health information under privacy laws in many countries. Visual privacy protection techniques, such as blurring or object removal, can be used to mitigate privacy concern, but they also obliterate important visual cues of affect and social behaviors that are crucial for the target applications. In this dissertation, we propose to balance the privacy …

Intelligent Methods For Optimum Online Adaptive Coordination Of Overcurrent Relays, Ke Xu

Theses and Dissertations--Electrical and Computer Engineering

During the operation in a modern power distribution system, some abnormal events may happen, such as over-voltage, faults, under-frequency and overloading, and so on. These abnormal events may cause a power outage in a distribution system or damages on the equipment in a distribution system. Hence these abnormal events should be identified and isolated by protection systems as quickly as possible to make sure we can maintain a stable and reliable distribution system to supply adequate electric power to the largest number of consumers as we can. To sum up, we need stable and reliable protection systems to satisfy this …

Fabrication And Characterization Of Organic-Inorganic Hybrid Perovskite Solar Cells, Hojjatollah Sarvari

Theses and Dissertations--Electrical and Computer Engineering

Solar energy as the most abundant source of energy is clean, non-pollutant, and completely renewable, which provides energy security, independence, and reliability. Organic-inorganic hybrid perovskite solar cells (PSCs) revolutionized the photovoltaics field not only by showing high efficiency of above 22% in just a few years but also by providing cheap and facile fabrication methods.

In this dissertation, fabrication of PSCs in both ambient air conditions and environmentally controlled N₂-filled glove-box are studied. Several characterization methods such as SEM, XRD, EDS, Profilometry, four-point probe measurement, EQE, and current-voltage measurements were employed to examine the quality of thin films …

Advanced Synchronous Machine Modeling, Yuqi Zhang

Theses and Dissertations--Electrical and Computer Engineering

The synchronous machine is one of the critical components of electric power systems. Modeling of synchronous machines is essential for power systems analyses. Electric machines are often interfaced with power electronic components. This work presents an advanced synchronous machine modeling, which emphasis on the modeling and simulation of systems that contain a mixture of synchronous machines and power electronic components. Such systems can be found in electric drive systems, dc power systems, renewable energy, and conventional synchronous machine excitation. Numerous models and formulations have been used to study synchronous machines in different applications. Herein, a unified derivation of the various …

Engineering Zinc Oxide Nanoparticles To Be Used As Nanofertilizers, Zeinah Elhaj Baddar

Theses and Dissertations--Plant and Soil Sciences

Zinc deficient soils, or soils with low Zn bioavailability, are widespread, which exacerbates Zn deficiency in human as crops grown on these soils have low Zn content. Often crop yields are also compromised. Fertilizers based on soluble Zn salts often have limited efficacy in such soils. In this research, we evaluate the performance of polymer coated and bare ZnO nanoparticles (NPs) in an attempt to overcome limitations of soluble Zn salts in alkaline soils. We first synthesized 20-30 nm bare ZnO NPs with different surface chemistries to impart colloidal stability to the particles. Bare ZnO were treated in phosphate solution …

Surface Engineering And Monomer Design For Light-Mediated Ring Opening Metathesis Polymerization, Ishan A. Fursule

Theses and Dissertations--Chemical and Materials Engineering

Stimuli-responsive materials are changing the landscape of actuated materials, optoelectronics, molecular machines, solar cells, temporary memory storage, and biomedical materials. Specifically, photo-responsive polymers have gained acceleration in research and application since the last two decades in the form of a surface coating and micro-patterns. Light as a stimulus can be coherent, mono or polychromatic, tunable for power (intensity) and energy (wavelength), and has precise spatiotemporal control. Conventional surface coating techniques such as spin coating are unable to impart properties to the coatings in terms of sturdiness, homogeneity, uniformity over the complex surface, post deposition modification, and process efficiency. Also, in …

Understanding Carbohydrate Recognition Mechanisms In Non-Catalytic Proteins Through Molecular Simulations, Abhishek A. Kognole

Theses and Dissertations--Chemical and Materials Engineering

Non-catalytic protein-carbohydrate interactions are an essential element of various biological events. This dissertation presents the work on understanding carbohydrate recognition mechanisms and their physical significance in two groups of non-catalytic proteins, also called lectins, which play key roles in major applications such as cellulosic biofuel production and drug delivery pathways. A computational approach using molecular modeling, molecular dynamic simulations and free energy calculations was used to study molecular-level protein-carbohydrate and protein-protein interactions. Various microorganisms like bacteria and fungi secret multi-modular enzymes to deconstruct cellulosic biomass into fermentable sugars. The carbohydrate binding modules (CBM) are non-catalytic domains of such enzymes that …

Application Of Process Systems Engineering Tools And Methods To Fermentation-Based Biorefineries, Kwabena Darkwah

Theses and Dissertations--Chemical and Materials Engineering

Biofuels produced from lignocellulosic biomass via the fermentation platform are sustainable energy alternatives to fossil fuels. Process Systems Engineering (PSE) uses computer-based tools and methods to design, simulate and optimize processes. Application of PSE tools to the design of economic biorefinery processes requires the development of simulation approaches that can be integrated with existing, mature PSE tools used to optimize traditional refineries, such as Aspen Plus. Current unit operation models lack the ability to describe unsteady state fermentation processes, link unsteady state fermentation with in situ separations, and optimize these processes for competing factors (e.g., yield and productivity). This work …