Engineering Commons^™

In-Situ Calibrated Modeling Of Residual Stresses Induced In Machining Under Various Cooling And Lubricating Environments, Julius M. Schoop

Mechanical Engineering Faculty Publications

Although many functional characteristics, such as fatigue life and damage resistance depend on residual stresses, there are currently no industrially viable ‘Digital Process Twin’ models (DPTs) capable of efficiently and quickly predicting machining-induced stresses. By leveraging advances in ultra-high-speed in-situ experimental characterization of machining and finishing processes under plane strain (orthogonal/2D) conditions, we have developed a set of physics-based semi-analytical models to predict residual stress evolution in light of the extreme gradients of stress, strain and temperature, which are unique to these thermo-mechanical processes. Initial validation trials of this novel paradigm were carried out in Ti-6Al4V and AISI 4340 alloy …

Initial Project Estimates For Design, Right Of Way, Utilities, And Construction, Christopher Van Dyke, Bryan Gibson, Jeff Jasper, Bob Lewis, Doug Kreis

Kentucky Transportation Center Research Report

Estimating the cost of highway construction projects is among the more challenging tasks state transportation agencies routinely deal with. Developing accurate estimates is a particularly fraught exercise during the planning and scoping phases, when projects have not been thoroughly defined and information on specifics is in short supply. While the Kentucky Transportation Cabinet (KYTC) has used several methodologies to generate initial cost estimates for design, right of way, utilities, and construction (DRUC), approaches vary between the agency’s districts. This report proposes a framework for estimating DRUC-related expenses that can be adopted throughout the state. Kentucky Transportation Center (KTC) researchers developed …

Volcanic Emissions And Atmospheric Pollution: A Study Of Nanoparticles, Erika M. Trejos, Luis F. O. Silva, James C. Hower, Eriko M. M. Flores, Carlos Mario González, Jorge E. Pachón, Beatriz H. Aristizábal

Center for Applied Energy Research Faculty and Staff Publications

The influence of emissions of an active volcano on the composition of nanoparticles and ultrafine road dust was identified in an urban area of the Andes. Although many cities are close to active volcanoes, few studies have evaluated their influence in road dust composition. Air quality in urban areas is significantly affected by non-exhaust emissions (e.g. road dust, brake wear, tire wear), however, natural sources such as volcanoes also impact the chemical composition of the particles. In this study, elements from volcanic emissions such as Si > Al > Fe > Ca > K > Mg, and Si—Al with K were identified as complex hydrates. …

Non-Nuclear Methods For Compaction Control Of Unbound Soil And Granular Layers, Brad Rister, Charlie Sun, Kean H. Ashurst Jr., Tim Jones, Christopher Van Dyke

Kentucky Transportation Center Research Report

In highway construction, the nuclear density gauge (NDG) is the industry standard for measuring soil density and moisture. They are widely used at state transportation agencies, however, because of their reliance on radiation, NDGs are expensive to maintain and have unique storage requirements. Operators must also earn specialized certifications and adhere to rigorous safety protocols. Equipment manufacturers have developed several non-nuclear density gauges which are more user friendly, however, their accuracy has sometimes not equaled NDGs. This comparative study evaluated the performance of the eGauge (a relatively new device) to NDGs. Over 100 soil density and moisture measurements were collected …

Fluid Separation And Network Deformation In Wetting Of Soft And Swollen Surfaces, Zhuoyun Cai, Artem Skabeev, Svetlana Morozova, Jonathan T. Pham

Chemical and Materials Engineering Faculty Publications

When a water drop is placed onto a soft polymer network, a wetting ridge develops at the drop periphery. The height of this wetting ridge is typically governed by the drop surface tension balanced by elastic restoring forces of the polymer network. However, the situation is more complex when the network is swollen with fluid, because the fluid may separate from the network at the contact line. Here we study the fluid separation and network deformation at the contact line of a soft polydimethylsiloxane (PDMS) network, swollen with silicone oil. By controlling both the degrees of crosslinking and swelling, we …

Transforming Corn Stover To Useful Transport Fuel Blends In Resource-Limited Settings, Nicholas Munu, Noble Banadda, Nicholas Kiggundu, Ahamada Zziwa, Isa Kabenge, Jeffrey Seay, Robert Kambugu, Joshua Wanyama, Albrecht Schmidt

Chemical and Materials Engineering Faculty Publications

Development of local technologies is crucial to the sustainable energy agenda in resource-limited countries and the world. Strengthening local green technologies and promoting local utilization will reduce carbon emissions that could be generated during transportation and delivery of green products from one country to another. In this paper we developed bio-oil/diesel blends using a low-tech pyrolysis system designed for smallholder farmers in developing countries and tested their appropriateness for diesel engines using standard ASTM methods. Corn stover retrieved from smallholder farmers in Gayaza, Uganda were pyrolyzed in a batch rocket stove reactor at 350 °C and liquid bio-oil harvested. Bio-oil …

Open-Field Scale-Model Experiments Of Fire Whirls Over L-Shaped Line Fires, Yuto Iga, Kazunori Kuwana, Kozo Sekimoto, Yuji Nakamura

Progress in Scale Modeling, an International Journal

This paper presents the results of open-field scale-model experiments of fire-whirl formation over line fires. L-shaped line fires were burned in crosswinds, and the processes of fire-whirl formation were observed. The flame height was measured using an image-processing technique, while two-dimensional velocity components were measured at two different locations using ultrasonic anemometers. Two tests were selected for comparison: test A, in which intense fire whirls repeatedly formed, and test B, in which no whirls were observed. In test A, the wind flow was bent by the fire plume, creating swirling flows near the burning area, thereby forming fire whirls. On …

Effect Of Reduced Plume Entrainment On The Burning Rate Of Porous Fuel Beds, Sara Mcallister

Progress in Scale Modeling, an International Journal

Large outdoor fires often exhibit unexpected fire behavior, particularly compared with much smaller fires. Understanding the difference between large- and small-scale fires is of importance for both fire behavior predictions and safety. Large fires are often characterized by very tall plumes that can extend to the stratosphere. Particularly as the actively burning area increases, plumes in large-scale fires likely entrain relatively little and may act in a similar fashion to a chimney. To explore the possible changes in burning rate due to the chimney effect, experiments were conducted with wood cribs burned with a chimney of variable height. The burning …

Scale Model Test To Estimate Thermal Damage By Fire In Aircraft Cargo, Jian Gao, Tsuneyoshi Matsuoka, Yuji Nakamura

Progress in Scale Modeling, an International Journal

The Federal Aviation Administration (FAA) requires fire detectors to alarm within one minute of the start of a fire in cargo compartments of airplanes. To determine whether such alarm timing works, investigations of the thermal damage to ceilings and other structures during the early stage of a fire were accomplished to demonstrate compliance with these FAA regulations. The objective was to test the feasibility of predicting convective heat transfer in early stage of a cargo compartment fire by conducting reduced scale (lab scale) experiments. First, the scaling laws was derived and validated. Then, full-scale and half-scale experiments were performed with …

Extinguishment Of Diffusion Flames Formed Over A Porous Plate Burner Using Rubber Balloons Filled With Inert Gases, Hiroyuki Torikai, Shinya Kudo

Progress in Scale Modeling, an International Journal

We have proposed an inert gas, rubber-balloon extinguishing method which might increase the effectiveness of extinguishing flames and decreasing the amounts of agents needed for fire suppression. Hence, extinguishing experiments have been performed to further clarify possible extinguishing characteristics, mechanisms and scaling effects of this method. Carbon dioxide, nitrogen, argon and helium gases were used as the extinguishing agents. Methane-air and propane-air diffusion flames were formed on two different diameter, round porous plate burner and used as the targets for extinguishment. The extinguishing probabilities were measured, and the extinguishing processes were observed with a high-speed camera. As a result, an …

Biodegradable Cellulose Film Prepared From Banana Pseudo-Stem Using An Ionic Liquid For Mango Preservation, Binling Ai, Lili Zheng, Wenqi Li, Xiaoyan Zheng, Yang Yang, Dao Xiao, Jian Shi, Zhanwu Sheng

Biosystems and Agricultural Engineering Faculty Publications

The excessive use and disposal of plastic packaging materials have drawn increasing concerns from the society because of the detrimental effect on environment and ecosystems. As the most widely used fruit packing material, polyethylene (PE) film is not suitable for long-term preservation of some tropical fruits, such as mangos, due to its inferior gas permeability. Cellulose based film can be made from renewable resources and is biodegradable and environmental-friendly, which makes it a promising alternative to PE as a packaging material. In this study, cellulose film synthesized from delignified banana stem fibers via an ionic liquid 1-Allyl-3-methylimidazolium chloride ([AMIm][Cl]) were …

Effects Of Dimensionless Numbers On Decomposition Of Methane Hydrate, Shoma Shimizu, Genichiro Kushida

Progress in Scale Modeling, an International Journal

It is necessary to elucidate the decomposition and combustion of methane hydrate for fire safety during transportation and storage to utilize it for commercial practice. The amount of methane evolved during the decomposition of methane hydrates is affected by the conditions such as the initial temperature, initial density and ambient temperature. In the present study, the internal temperature of methane hydrate and the amount of methane evolved during its decomposition were investigated by a dimensionless numerical analysis using a transient one-dimensional conduction model from a symmetrical methane hydrate ball heated by ambient air. The numerically calculated central temperature and the …

Copper Oxide Nanoparticle Diameter Mediates Serum-Sensitive Toxicity In Beas-2b Cells, Angie S. Morris, Brittany E. Givens, Aaron Silva, Aliasger K. Salem

Chemical and Materials Engineering Faculty Publications

Copper oxide (CuO) nanoparticles (NPs) are abundant in manufacturing processes, but they are an airway irritant. In vitro pulmonary toxicity of CuO NPs has been modeled using cell lines such as human bronchial epithelial cell line BEAS-2B. In 2D in vitro culture, BEAS-2B undergoes squamous differentiation due to the presence of serum. Differentiation is part of the repair process of lung cells in vivo that helps to preserve the epithelial lining of the respiratory tract. Herein, the effects of serum on the hydrodynamic diameter, cellular viability, cellular differentiation, and cellular uptake of 5 and 35 nm CuO NPs are investigated, …

A Study On Fire Hazards Of Oil Tanks In Urban Areas With Scale Model Experiments, Ho Yin Ng, Yu Wan, Wan Ki Chow

Progress in Scale Modeling, an International Journal

Large fuel tanks are located in an urban area of Tsing Yi in Hong Kong, giving potentially high risks to people living nearby if a fire was to occur. Scale modeling experiments were carried out to investigate the potential of fire hazards. Propanol pool fires with five different scales of oil tanks were studied first. Appropriate tank sizes were then put in a 1/2500 architectural scale model on the Tsing Yi Island to study a fuel tank fire. Results show that the heat and smoke from a fire would affect occupants staying in areas near to the fuel tanks. Fire …

Fingering Behavior Of Flame Spread Over Solid Combustibles, Tsuneyoshi Matsuoka, Kentaro Nakashima, Takuma Kajimoto, Akihiro Yoshimasa, Yuji Nakamura

Progress in Scale Modeling, an International Journal

In this study, the fingering pattern formation and the following flamelet spreading over three different kinds of thick combustibles, i.e., Poly methacrylate (PMMA), Poly ethylene (PE) and Poly carbonate (PC) were observed and the effective Lewis number correlation was validated. Experiments were performed with a narrow channel apparatus. In addition to the kinds of solid fuel materials, the channel height and the oxidizer velocity were varied as experimental parameters. An image analysis method was developed to quantify the number, diameter and spread rate of the flamelets. Replacing the fuel thickness into the thermal thickness, the effective Lewis number which is …

Evaluation Of Orange Pavement Striping For Use In Work Zones, Erin Lammers-Staats, William Staats, Ken Agent

Kentucky Transportation Center Research Report

Interstate widening projects are commonplace in Kentucky, and safety is of primary concern within the project work zone. Past experience with long work zones revealed two critical safety issues: driver confusion due to unclear pavement markings and a lack of continuous work zone signage for motorists indicating they are still within a work zone. This concern is heightened in transition and taper areas. Highly visible markings in an alternative color other than standard yellow or white might better distinguish the proper travel path for motorists and prevent drivers from returning to normal driving behavior and speeds once they get through …

Fiscal Year 2019 Fhwa-536 Report For The Kentucky Transportation Cabinet, Doug Kreis, Candice Wallace, Bryan Gibson, Sarah Mccormack

Kentucky Transportation Center Research Report

The Federal Highway Administration (FHWA) requires state transportation agencies to submit a biennial report on local highway finances. The purpose of these reports is to provide FHWA with the data it needs to capture the financing of highway activities at the local level. Based on this information, it can identify trends in revenue, expenditures, investments, and program development, and in turn make decisions about future investments. The report, FHWA-536, asks agencies to report on four areas of local highway finance: 1) disposition of highway-user revenues; 2) revenues used for roads and streets identified by source and funding type; 3) road …

Development, Implementation, And Tracking Of Preventative Safety Metrics, Zamaan Al-Shabbani, Ashtarout Ammar, Hala Nassereddine, Gabriel B. Dadi

Kentucky Transportation Center Research Report

What gets measured, gets improved. With respect to the safety and health of Kentucky Transportation Cabinet (KYTC) employees, the primary metric used has been the OSHA recordable incident rate. This incident rate measures how often a Cabinet employee sustains an injury that demands more than basic first aid. This metric is important for understanding injury frequencies, but it does not assist with management of the safety, health, and overall well-being of KYTC personnel. Based on a review of leading safety indicators adopted by various industries, this study devised a comprehensive list of safety metrics the Cabinet will benefit from tracking. …

Commercial Driver’S License Prosecution, Adjudication, And Data Transmission, Andrew Martin, Jeeyen Koo, Jennifer Walton

Kentucky Transportation Center Research Report

The Kentucky Transportation Center research team examined law enforcement and adjudication of traffic offenses committed by commercial driver’s license holders. The objectives were to identify states that would provide the data, collect information about their court systems, analyze enforcement and/or adjudication data, and make some general observations about trends. Many state agencies were not able to provide their traffic offense data and therefore, the team focused primarily on data from Kentucky and Washington State.

The study focused on enforcement trends and adjudication of safety-related offenses. Overall, conviction rates remain higher than dismissal and amended rates. In recent years, dismissal and …

Data-Driven Tools Guided By First-Principles For Scale Modeling, Sadegh Poozesh

Progress in Scale Modeling, an International Journal

For decades, traditional scale-modeling techniques have been relying on first-principles models (FPMs). FPMs have been used to find non-dimensional numbers (PIs) and identify normalized underlying forces and energies behind the phenomenon in focus. The two main challenges with FPM-based PIs extraction are finding the relevant PIs and proper correlations between PIs. The emergence and surge of data-driven modeling (DDM) provide a new opportunity to leverage experimental data in model development across scales/plants. In this paper, first, the two mentioned issues in PIs development will be elaborated to reveal the gap, and second, a new insight into scale modeling and similarity …

Radiation‐Induced Oral Mucositis Hamster Model Using A Linear Accelerator Enhances Clinical Relevance Of Preclinical Studies For Treatment Strategy Investigation, Carolyn T. Jordan, Emily M. Bradford, Dennis C. Cheek, Mahesh R. Kudrimoti, Craig S. Miller, Molly H. Smith, J. Zach Hilt, Thomas D. Dziubla

Radiation Medicine Faculty Publications

Translational animal models for oral mucositis (OM) are necessary to simulate and assess the bioclinical effects and response in humans. These models should simulate high levels of radiation exposure that leads to oxidative stress and inflammatory‐initiated tissue changes. Hamster models have been extensively studied to observe pathological effects of radiation exposure and help in the development of effective treatments. To successfully evaluate the potential for treatment regimens with consistency and relevance, a radiation‐induced OM hamster model was developed using a clinical linear accelerator utilized by cancer patients daily. The dose exposure to the isolated, everted cheek pouch of a hamster, …

Blowing Curtain Face Ventilation System For Extended Cut Mining Using Passive Regulator, Andrzej M. Wala, Todor P. Petrov

Mining Engineering Faculty Patents

A ventilation system for an underground mine includes a blowing curtain, a passive regulator in a shape of an airfoil and an airflow ventilation source. The passive regulator is positioned in the air path adjacent a discharge end of the blowing curtain.

Broad Kinase Inhibition Mitigates Early Neuronal Dysfunction In Tauopathy, Shon A. Koren, Matthew J. Hamm, Ryan Cloyd, Sarah N. Fontaine, Emad Chishti, Chiara Lanzillotta, Jennifer Rodriguez-Rivera, Alexandria Ingram, Michelle Bell, Sara M. Galvis-Escobar, Nicholas Zulia, Fabio Di Domenico, Duc Duong, Nicholas T. Seyfried, David K. Powell, Moriel Vandsburger, Tal Frolinger, Anika M. S. Hartz, John Koren Iii, Jeffrey M. Axten, Nicholas J. Laping, Jose F. Abisambra

Sanders-Brown Center on Aging Faculty Publications

Tauopathies are a group of more than twenty known disorders that involve progressive neurodegeneration, cognitive decline and pathological tau accumulation. Current therapeutic strategies provide only limited, late-stage symptomatic treatment. This is partly due to lack of understanding of the molecular mechanisms linking tau and cellular dysfunction, especially during the early stages of disease progression. In this study, we treated early stage tau transgenic mice with a multi-target kinase inhibitor to identify novel substrates that contribute to cognitive impairment and exhibit therapeutic potential. Drug treatment significantly ameliorated brain atrophy and cognitive function as determined by behavioral testing and a sensitive imaging …

An Ultrabroadband 3d Achromatic Metalens, Fatih Balli, Mansoor A. Sultan, Aytekin Ozdemir, J. Todd Hastings

Electrical and Computer Engineering Faculty Publications

We design and fabricate ultra-broadband achromatic metalenses operating from the visible into the short-wave infrared, 450–1700 nm, with diffraction-limited performance. A hybrid 3D architecture, which combines nanoholes with a phase plate, allows realization in low refractive index materials. As a result, two-photon lithography can be used for prototyping while molding can be used for mass production. Experimentally, a 0.27 numerical aperture (NA) metalens exhibits 60% average focusing efficiency and 6% maximum focal length error over the entire bandwidth. In addition, a 200 μm diameter, 0.04 NA metalens was used to demonstrate achromatic imaging over the same broad spectral range. These …

An Advanced Machine Learning Based Energy Management Of Renewable Microgrids Considering Hybrid Electric Vehicles’ Charging Demand, Tianze Lan, Kittisak Jermsittiparsert, Sara T. Al-Rashood, Mostafa Rezaei, Loiy Al-Ghussain, Mohammed A. Mohammed

Mechanical Engineering Graduate Research

Renewable microgrids are new solutions for enhanced security, improved reliability and boosted power quality and operation in power systems. By deploying different sources of renewables such as solar panels and wind units, renewable microgrids can enhance reducing the greenhouse gasses and improve the efficiency. This paper proposes a machine learning based approach for energy management in renewable microgrids considering a reconfigurable structure based on remote switching of tie and sectionalizing. The suggested method considers the advanced support vector machine for modeling and estimating the charging demand of hybrid electric vehicles (HEVs). In order to mitigate the charging effects of HEVs …

Peak Reduction And Long Term Load Forecasting For Large Residential Communities Including Smart Homes With Energy Storage, Huangjie Gong, Vandana Rallabandi, Michael L. Mcintyre, Eklas Hossain, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

Domestic load profiles in the residential sectors are being modified with the adoption of smart home management systems and solar generation. In addition, houses with rooftop PV behave like local generators, contributing to the growth of the penetration of PV energy. Hence, the demand for power is declining day by day. However, the increasing PV penetration causes technical challenges for the power system, such as the “duck curve”. This can be addressed through home energy management (HEM) techniques including peak shaving, load shifting with smart home devices. In this regard, electric water heaters (EWH), with high thermal mass and being …

New Mechanism Insight For The Hydrogenation Of Co/Co2 Gas Mixtures To Hydrocarbons Over Iron-Based Catalyst, Sandeep Badoga, Michela Martinelli, Muthu Kumaran Gnanamani, Young Koh, Wilson D. Shafer

Center for Applied Energy Research Faculty and Staff Publications

Iron-based catalysts are the most suitable candidates for converting CO₂ or CO₂-rich syngas to hydrocarbons. However, several issues about the mechanism of CO₂ hydrogenation are still unclear. In this work, we investigated the performance of an iron-based catalyst with H₂/CO₂, H₂/CO/N₂ and H₂/CO/¹³CO₂/N₂ gas mixtures at the same process conditions (T = 270°C, P = 175 psi and SV = 3 NL/h/g_cat). The CO₂ hydrogenation rate was much lower than that observed for CO hydrogenation. ¹³CO_{2 …}

Clinical Evaluation Of Respiratory Rate Measurements On Copd (Male) Patients Using Wearable Inkjet-Printed Sensor, Ala'aldeen Al-Halhouli, Loiy Al-Ghussain, Osama Khallouf, Alexander Rabadi, Jafar Alawadi, Haipeng Liu, Khaled Al Oweidat, Fei Chen, Dingchang Zheng

Mechanical Engineering Graduate Research

Introduction: Chronic Obstructive Pulmonary Disease (COPD) is a progressive disease that causes long-term breathing problems. The reliable monitoring of respiratory rate (RR) is very important for the treatment and management of COPD. Based on inkjet printing technology, we have developed a stretchable and wearable sensor that can accurately measure RR on normal subjects. Currently, there is a lack of comprehensive evaluation of stretchable sensors in the monitoring of RR on COPD patients. We aimed to investigate the measurement accuracy of our sensor on COPD patients. Methodology: Thirty-five patients (Mean ± SD of age: 55.25 ± 13.76 years) in different stages …

Effects Of Racing Surface And Turn Radius On Fatal Limb Fractures In Thoroughbred Racehorses, Michael L. Peterson, Wayne T. Sanderson, Nurlan Kussainov, Sarah Jane Hobbs, Patti Miles, Mary C. Scollay, Hilary M. Clayton

Biosystems and Agricultural Engineering Faculty Publications

North American Thoroughbred racing is conducted on three types of surfaces—dirt, turf, and synthetic. The tracks are oval, and races are run counterclockwise. The loading on right and left limbs is expected to differ as a function of turn radius, banking, surface, and gait asymmetry. Hind limbs and forelimbs also have different functions related to propulsion and turning, respectively. This study uses the Equine Injury Database for race starts from 1 January 2009 through 31 December 2014, to compare injury rates across participating North American racetracks. The data are limited to catastrophic injuries in which horses died or were euthanized …

Corrosion Protective Film Formation On Mg Alloys Az 31 By Exposure To Dilute Selenite Solutions, Zhiyuan Feng, Charles C. Xu, Dadi Zhang, Rudolph Buchheit

Chemical and Materials Engineering Faculty Publications

The study of protective film formation on Mg alloys by exposure to sodium selenite solutions was conducted. Anodic polarization studies, electrochemical impedance spectroscopy studies, morphological analysis, and Energy-dispersive X-ray spectroscopy were performed on AZ31 Mg alloy after coating treatment in different concentrations of sodium selenite. The corrosion resistance was improved by around 5 times compared with control. Improved resistance to localized corrosion was observed in the coatings treated by 5 mM or 10 mM sodium selenite. The protection mechanism was ascribed to the transformation of selenite to insoluble selenium, the formation of insoluble MgSeO₃ hydrate, and polymerization of amorphous …