Open Access. Powered by Scholars. Published by Universities.®

Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

University of Central Florida

Discipline
Keyword
Publication Year
Publication
Publication Type
File Type

Articles 2791 - 2820 of 4566

Full-Text Articles in Engineering

Preparation And Characterisation Of Stabilized Nafion/Phosphotungstic Acid Composite Membranes For Proton Exchange Membrane Fuel Cell (Pemfc) Automobile Engines, Rohit Agarwal Jan 2008

Preparation And Characterisation Of Stabilized Nafion/Phosphotungstic Acid Composite Membranes For Proton Exchange Membrane Fuel Cell (Pemfc) Automobile Engines, Rohit Agarwal

Electronic Theses and Dissertations

Membrane durability is one of the limiting factors for proton exchange membrane fuel cell (PEMFC) commercialisation by limiting the lifetime of the membrane via electrochemical / mechanical / thermal degradation. Lower internal humidity in the membrane at high temperature ( > 100 °C) and low relative humidity (25-50 %RH) operating conditions leads to increased resistance, lowering of performance and higher degradation rate. One of the promising candidates is composite proton exchange membranes (CPEMs) which have heteropoly acid (HPA) e.g. Phosphotungstic acid (PTA) doped throughout the Nafion® matrix. HPA is primarily responsible for carrying intrinsic water which reduces the external water dependence. …

Go to article

Synthesis And Characterization Of Polymer-Derived Porous Sicn Ceramics, Yun Wei Jan 2008

Synthesis And Characterization Of Polymer-Derived Porous Sicn Ceramics, Yun Wei

Electronic Theses and Dissertations

The synthesis and characterization of porous SiCN ceramics produced by the method of polymer-derived ceramics were studied in this work. The polymer-to-ceramic conversion technique is a novel revolution in the methods for fabricating porous materials with controlled morphologies and tailored properties. The porous SiCN ceramics can be successfully prepared from thermal decomposition of polymeric precursors (polysilazane) and the pore former (polyvinyl alcohol (PVA)). The fabrication procedures involved the mixing of the pre-ceramic precursor with appropriate concentration of the PVA, curing, pyrolysis and subsequent PVA removal, leaving pores in the ceramic matrix. The material obtained revealed a homogeneous amorphous microstructure consisting …

Go to article

A Comparative Analysis Of Green Roof Designs Including Depth Of Media, Drainage Layer Materials, And Pollution Control Media, Matt Kelly Jan 2008

A Comparative Analysis Of Green Roof Designs Including Depth Of Media, Drainage Layer Materials, And Pollution Control Media, Matt Kelly

Electronic Theses and Dissertations

Population growth has lead to an increase in development and impervious areas in urban settings. Post-development conditions cause several problems for stormwater management such as limited space for stormwater storage systems and the conveyance of pollution picked up by runoff to near by water bodies. Green Roofs with cisterns have been shown to attenuate the peak flow of storm events and reduce the pollution load leaving a site and entering nearby water bodies. The purpose of this research is to expand the available research data on green roofs with cisterns by investigating the water quality and hydrology effects of different …

Go to article

Finite Element Modeling Of Tides And Currents Of The Pascagoula River, Qing Wang Jan 2008

Finite Element Modeling Of Tides And Currents Of The Pascagoula River, Qing Wang

Electronic Theses and Dissertations

This thesis focuses on the simulation of astronomic tides of the Pascagoula River. The work is comprised of five steps: 1) Production of a digital elevation model describing the entire Pascagoula River system; 2) Development of an inlet-based, unstructured mesh for inbank flow to better understand the basis of the hydrodynamics within the Pascagoula riverine system. In order to assist in the mesh development, a toolbox was constructed to implement one-dimensional river cross sections into the two-dimensional model; 3) Implementation of a sensitivity analysis of the Pascagoula River two inlet system to examine the inlet effects on tidal propagation; 4) …

Go to article

Real-Time Trajectory Planning For Groundand Aerial Vehicles In A Dynamic Environment, Jian Yang Jan 2008

Real-Time Trajectory Planning For Groundand Aerial Vehicles In A Dynamic Environment, Jian Yang

Electronic Theses and Dissertations

In this dissertation, a novel and generic solution of trajectory generation is developed and evaluated for ground and aerial vehicles in a dynamic environment. By explicitly considering a kinematic model of the ground vehicles, the family of feasible trajectories and their corresponding steering controls are derived in a closed form and are expressed in terms of one adjustable parameter for the purpose of collision avoidance. A collision-avoidance condition is developed for the dynamically changing environment, which consists of a time criterion and a geometrical criterion. By imposing this condition, one can determine a family of collision-free paths in a closed …

Go to article

Amorphous Phase Formation In Mechanically Alloyed Fe-Based Systems., Satyajeet Sharma Jan 2008

Amorphous Phase Formation In Mechanically Alloyed Fe-Based Systems., Satyajeet Sharma

Electronic Theses and Dissertations

Bulk metallic glasses have interesting combination of physical, chemical, mechanical, and magnetic properties which make them attractive for a variety of applications. Consequently there has been a lot of interest in understanding the structure and properties of these materials. More varied applications can be sought if one understands the reasons for glass formation and the methods to control them. The glass-forming ability (GFA) of alloys can be substantially increased by a proper selection of alloying elements and the chemical composition of the alloy. High GFA will enable in obtaining large section thickness of amorphous alloys. Ability to produce glassy alloys …

Go to article

Drive-Based Modeling And Visualization Of Crew Race Strategy And Performance, Jeffrey Cornett Jan 2008

Drive-Based Modeling And Visualization Of Crew Race Strategy And Performance, Jeffrey Cornett

Electronic Theses and Dissertations

Crew race strategy is typically formulated by coaches based on rowing tradition and years of experience. However, coaching strategies are not generally supported by empirical evidence and decision-support models. Previous models of crew race strategy have been constrained by the sparse information published on crew race performance (quarterly 500-meter splits). Empirical research has merely summarized which quarterly splits averaged the fastest and slowest relative to the other splits and relative to the average speed of the other competitors. Video records of crew race world championships provide a rich source of data for those capable and patient enough to mine this …

Go to article

Numerical Modeling Of Wave Propagation In Nonlinear Photonic Crystal Fiber, Md. Kaisar Khan Jan 2008

Numerical Modeling Of Wave Propagation In Nonlinear Photonic Crystal Fiber, Md. Kaisar Khan

Electronic Theses and Dissertations

In this dissertation, we propose numerical techniques to explain physical phenomenon of nonlinear photonic crystal fiber (PCF). We explain novel physical effects occurred in PCF subjected to very short duration pulses including soliton. To overcome the limitations in the analytical formulation for PCF, an accurate and efficient numerical analysis is required to explain both linear and nonlinear physical characteristics. A vector finite element based model was developed to precisely synthesize the guided modes in order to evaluate coupling coefficients, nonlinear coefficient and higher order dispersions of PCFs. This finite element model (FEM) is capable of evaluating coupling length of directional …

Go to article

A High-Resolution Storm Surge Model For The Pascagoula Region, Mississippi, Naeko Takahashi Jan 2008

A High-Resolution Storm Surge Model For The Pascagoula Region, Mississippi, Naeko Takahashi

Electronic Theses and Dissertations

The city of Pascagoula and its coastal areas along the United States Gulf Coast have experienced many catastrophic hurricanes and were devastated by high storm surges caused by Hurricane Katrina (August 23 to 30, 2005). The National Hurricane Center reported high water marks exceeding 6 meters near the port of Pascagoula with a near 10-meter high water mark recorded near the Hurricane Katrina landfall location in Waveland, MS. Although the Pascagoula River is located 105 km east of the landfall location of Hurricane Katrina, the area was devastated by storm surge-induced inundation because of its low elevation. Building on a …

Go to article

Phase-Shifting Haar Wavelets For Image-Based Rendering Applications, Mais Alnasser Jan 2008

Phase-Shifting Haar Wavelets For Image-Based Rendering Applications, Mais Alnasser

Electronic Theses and Dissertations

In this thesis, we establish the underlying research background necessary for tackling the problem of phase-shifting in the wavelet transform domain. Solving this problem is the key to reducing the redundancy and huge storage requirement in Image-Based Rendering (IBR) applications, which utilize wavelets. Image-based methods for rendering of dynamic glossy objects do not truly scale to all possible frequencies and high sampling rates without trading storage, glossiness, or computational time, while varying both lighting and viewpoint. This is due to the fact that current approaches are limited to precomputed radiance transfer (PRT), which is prohibitively expensive in terms of memory …

Go to article

Improving Airline Schedule Reliability Using A Strategic Multi-Objective Runway Slot Assignment Search Heuristic, Florian Hafner Jan 2008

Improving Airline Schedule Reliability Using A Strategic Multi-Objective Runway Slot Assignment Search Heuristic, Florian Hafner

Electronic Theses and Dissertations

Improving the predictability of airline schedules in the National Airspace System (NAS) has been a constant endeavor, particularly as system delays grow with ever-increasing demand. Airline schedules need to be resistant to perturbations in the system including Ground Delay Programs (GDPs) and inclement weather. The strategic search heuristic proposed in this dissertation significantly improves airline schedule reliability by assigning airport departure and arrival slots to each flight in the schedule across a network of airports. This is performed using a multi-objective optimization approach that is primarily based on historical flight and taxi times but also includes certain airline, airport, and …

Go to article

Optimizing The Level Of Customization For Products In Mass Customization Systems, Sami Spahi Jan 2008

Optimizing The Level Of Customization For Products In Mass Customization Systems, Sami Spahi

Electronic Theses and Dissertations

Mass customization (MC) was developed to capitalize on the combined benefits of economies of scale and economies of scope. Balancing the tradeoffs involved in an MC system warrants the determination of the degree or the extent of customization. Most of the literature views the degree of customization as how early or how far the customer is integrated in the production cycle, which is defined as the order decoupling point. In this study we are addressing the degree of customization from a product structural perspective. There are two objectives in this research. The first is to develop a unit of measurement …

Go to article

A Customer Programmable Microfluidic System, Miao Liu Jan 2008

A Customer Programmable Microfluidic System, Miao Liu

Electronic Theses and Dissertations

Microfluidics is both a science and a technology offering great and perhaps even revolutionary capabilities to impact the society in the future. However, due to the scaling effects there are unknown phenomena and technology barriers about fluidics in microchannel, material properties in microscale and interactions with fluids are still missing. A systematic investigation has been performed aiming to develop "A Customer Programmable Microfluidic System". This innovative Polydimethylsiloxane (PDMS)-based microfluidic system provides a bio-compatible platform for bio-analysis systems such as Lab-on-a-chip, micro-total-analysis system and biosensors as well as the applications such as micromirrors. The system consists of an array of microfluidic …

Go to article

Effect Of Pressure Gradient And Wake On Endwall Film Cooling Effectiveness, Sylvette Rodriguez Jan 2008

Effect Of Pressure Gradient And Wake On Endwall Film Cooling Effectiveness, Sylvette Rodriguez

Electronic Theses and Dissertations

Endwall film cooling is a necessity in modern gas turbines for safe and reliable operation. Performance of endwall film cooling is strongly influenced by the hot gas flow field, among other factors. For example, aerodynamic design determines secondary flow vortices such as passage vortices and corner vortices in the endwall region. Moreover blockage presented by the leading edge of the airfoil subjects the incoming flow to a stagnating pressure gradient leading to roll-up of the approaching boundary layer and horseshoe vortices. In addition, for a number of heavy frame power generation gas turbines that use cannular combustors, the hot and …

Go to article

Optical Solitons In Periodic Structures, Konstantinos Makris Jan 2008

Optical Solitons In Periodic Structures, Konstantinos Makris

Electronic Theses and Dissertations

By nature discrete solitons represent self-trapped wavepackets in nonlinear periodic structures and result from the interplay between lattice diffraction (or dispersion) and material nonlinearity. In optics, this class of self-localized states has been successfully observed in both one-and two-dimensional nonlinear waveguide arrays. In recent years such lattice structures have been implemented or induced in a variety of material systems including those with cubic (Kerr), quadratic, photorefractive, and liquid-crystal nonlinearities. In all cases the underlying periodicity or discreteness leads to new families of optical solitons that have no counterpart whatsoever in continuous systems. In the first part of this dissertation, a …

Go to article

High Temperature Packaging For Wide Bandgap Semiconductor Devices, Brian Grummel Jan 2008

High Temperature Packaging For Wide Bandgap Semiconductor Devices, Brian Grummel

Electronic Theses and Dissertations

Currently, wide bandgap semiconductor devices feature increased efficiency, higher current handling capabilities, and higher reverse blocking voltages than silicon devices while recent fabrication advances have them drawing near to the marketplace. However these new semiconductors are in need of new packaging that will allow for their application in several important uses including hybrid electrical vehicles, new and existing energy sources, and increased efficiency in multiple new and existing technologies. Also, current power module designs for silicon devices are rife with problems that must be enhanced to improve reliability. This thesis introduces new packaging that is thermally resilient and has reduced …

Go to article

Design And Optimization Of Nanostructured Optical Filters, Jeremiah Brown Jan 2008

Design And Optimization Of Nanostructured Optical Filters, Jeremiah Brown

Electronic Theses and Dissertations

Optical filters encompass a vast array of devices and structures for a wide variety of applications. Generally speaking, an optical filter is some structure that applies a designed amplitude and phase transform to an incident signal. Different classes of filters have vastly divergent characteristics, and one of the challenges in the optical design process is identifying the ideal filter for a given application and optimizing it to obtain a specific response. In particular, it is highly advantageous to obtain a filter that can be seamlessly integrated into an overall device package without requiring exotic fabrication steps, extremely sensitive alignments, or …

Go to article

Value Mapping Framework Involving Stakeholders For Supply Chain Improvement When Implementing Information Technology Projects, Karla Moore Jan 2008

Value Mapping Framework Involving Stakeholders For Supply Chain Improvement When Implementing Information Technology Projects, Karla Moore

Electronic Theses and Dissertations

Successful Supply Chain Management (SCM) depends on how well an organization performs internal and external communications with trading partners, executes the logistics component, and understands/monitors related costs of conducting its business. The use of information technology (IT) is considered a prerequisite for the effective control of today's complex supply chains. Increased communication technology has redefined how businesses work together, raised customer expectations, and placed new demands on supply chain performance. IT components with proven and rapid return-on-investment are favored to support critical supply chain processes such as leaner manufacturing processes, consumer-driven supply chains, and customer responsiveness. The use of IT …

Go to article

Design Of An Adaptive Autopilot For An Expendable Launch Vehicle, Clinton Plaisted Jan 2008

Design Of An Adaptive Autopilot For An Expendable Launch Vehicle, Clinton Plaisted

Electronic Theses and Dissertations

This study investigates the use of a Model Reference Adaptive Control (MRAC) direct approach to solve the attitude control problem of an Expendable Launch Vehicle (ELV) during its boost phase of flight. The adaptive autopilot design is based on Lyapunov Stability Theory and provides a useful means for controlling the ELV in the presence of environmental and dynamical uncertainties. Several different basis functions are employed to approximate the nonlinear parametric uncertainties in the system dynamics. The control system is designed so that the desire dresponse to a reference model would be tracked by the closed-loop system. The reference model is …

Go to article

An Adaptive Multiobjective Evolutionary Approach To Optimize Artmap Neural Networks, Assem Kaylani Jan 2008

An Adaptive Multiobjective Evolutionary Approach To Optimize Artmap Neural Networks, Assem Kaylani

Electronic Theses and Dissertations

This dissertation deals with the evolutionary optimization of ART neural network architectures. ART (adaptive resonance theory) was introduced by a Grossberg in 1976. In the last 20 years (1987-2007) a number of ART neural network architectures were introduced into the literature (Fuzzy ARTMAP (1992), Gaussian ARTMAP (1996 and 1997) and Ellipsoidal ARTMAP (2001)). In this dissertation, we focus on the evolutionary optimization of ART neural network architectures with the intent of optimizing the size and the generalization performance of the ART neural network. A number of researchers have focused on the evolutionary optimization of neural networks, but no research has …

Go to article

Prevention Of Environmentally Induced Degradation In Carbon/Epoxy Composite Material Via Implementation Of A Polymer Based Coati, Bradford Tipton Jan 2008

Prevention Of Environmentally Induced Degradation In Carbon/Epoxy Composite Material Via Implementation Of A Polymer Based Coati, Bradford Tipton

Electronic Theses and Dissertations

As the use of fiber reinforced plastics increases in such industries as aerospace, wind energy, and sporting goods, factors effecting long-term durability, such as environmental exposure, are of increasing interest. The primary objectives of this study were to examine the effects of extensive environmental exposure (specifically UV radiation and moisture) on carbon/epoxy composite laminate structures and to determine the relative effectiveness of polymer-based coatings at mitigating degradation incurred due to such exposure. Carbon/epoxy composite specimens, both coated and uncoated, were subjected to accelerated weathering in which prolonged outdoor exposure was simulated by controlling the radiation wavelength (in the UV region), …

Go to article

Improving Business Performance Through The Integration Of Human Factors Engineering Into Organizations Using A Systems Engineeri, Monica Philippart Jan 2008

Improving Business Performance Through The Integration Of Human Factors Engineering Into Organizations Using A Systems Engineeri, Monica Philippart

Electronic Theses and Dissertations

Most organizations today understand the valuable contribution employees as people (rather than simply bodies) provide to their overall performance. Although efforts are made to make the most of the human in organizations, there is still much room for improvement. Focus in the reduction of employee injuries such as cumulative trauma disorders rose in the 80 s. Attempts at increasing performance by addressing employee satisfaction through various methods have also been ongoing for several years now. Knowledge Management is one of the most recent attempts at controlling and making the best use of employees knowledge. All of these efforts and more …

Go to article

Low Reynolds Number Water Flow Characteristics Through Rectangular Micro Diffusers/Nozzles With A Primary Focus On Major/Minor P, Kyle Hallenbeck Jan 2008

Low Reynolds Number Water Flow Characteristics Through Rectangular Micro Diffusers/Nozzles With A Primary Focus On Major/Minor P, Kyle Hallenbeck

Electronic Theses and Dissertations

The field of microfluidics has recently been gathering a lot of attention due to the enormous demand for devices that work in the micro scale. The problem facing many researchers and designers is the uncertainty in using macro scaled theory, as it seems in some situations they are incorrect. The general idea of this work was to decide whether or not the flow through micro diffusers and nozzles follow the same trends seen in macro scale theory. Four testing wafers were fabricated using PDMS soft lithography including 38 diffuser/nozzle channels a piece. Each nozzle and diffuser consisted of a throat …

Go to article

Empirical Relationships Betweenload Test Data And Predicted Compression Capacity Of Augered Cast-In-Place Piles In Predominantly, Donald Mccarthy Jan 2008

Empirical Relationships Betweenload Test Data And Predicted Compression Capacity Of Augered Cast-In-Place Piles In Predominantly, Donald Mccarthy

Electronic Theses and Dissertations

Augered Cast-In-Place (ACIP) Piles are used in areas were the loading from a superstructure exceeds the soil bearing capacity for usage of a shallow foundation. In Northwest Florida and along the Gulf Coast, ACIP piles are often utilized as foundation alternatives for multi-story condominium projects. Data from 25 compression load tests at 13 different project sites in Florida and Alabama were analyzed to determine their individual relationships between anticipated and determined compression load capacity. The anticipated capacity of the ACIP pile is routinely overestimated due to uncertainties involved with the process of estimating the compressive capacity and procedures of placing …

Go to article

Low Noise, High Repetition Rate Semiconductor-Based Mode-Locked Lasers For Signal Processing And Coherent Communications, Franklyn Quinlan Jan 2008

Low Noise, High Repetition Rate Semiconductor-Based Mode-Locked Lasers For Signal Processing And Coherent Communications, Franklyn Quinlan

Electronic Theses and Dissertations

This dissertation details work on high repetition rate semiconductor mode-locked lasers. The qualities of stable pulse trains and stable optical frequency content are the focus of the work performed. First, applications of such lasers are reviewed with particular attention to applications only realizable with laser performance such as presented in this dissertation. Sources of timing jitter are also reviewed, as are techniques by which the timing jitter of a 10 GHz optical pulse train may be measured. Experimental results begin with an exploration of the consequences on the timing and amplitude jitter of the phase noise of an RF source …

Go to article

Ultrashort Laser Pulse Interaction With Photo-Thermo-Refractive Glass, Leo Siiman Jan 2008

Ultrashort Laser Pulse Interaction With Photo-Thermo-Refractive Glass, Leo Siiman

Electronic Theses and Dissertations

Photo-thermo-refractive (PTR) glass is an ideal photosensitive material for recording phase volume holograms. It is a homogeneous multi-component silicate glass that demonstrates all the advantages of optical glass: thermal stability, high laser damage threshold, and a wide transparency range. Moreover the ability to record phase patterns (i.e. spatial refractive index variations) into PTR glass has resulted in the fabrication of volume holograms with diffraction efficiency greater than 99%. The conventional method of recording a hologram in PTR glass relies on exposure to continuous-wave ultraviolet laser radiation. In this dissertation the interaction between infrared ultrashort laser pulses and PTR glass is …

Go to article

Cholesteric Liquid Crystal Photonic Crystal Lasers And Photonic Devices, Ying Zhou Jan 2008

Cholesteric Liquid Crystal Photonic Crystal Lasers And Photonic Devices, Ying Zhou

Electronic Theses and Dissertations

This dissertation discusses cholesteric liquid crystals (CLCs) and polymers based photonic devices including one-dimensional (1D) photonic crystal lasers and broadband circular polarizers. CLCs showing unique self-organized chiral structures have been widely used in bistable displays, flexible displays, and reflectors. However, the photonic band gap they exhibit opens a new way for generating laser light at the photonic band edge (PBE) or inside the band gap. When doped with an emissive laser dye, cholesteric liquid crystals provide distributed feedback so that mirrorless lasing is hence possible. Due to the limited surface anchoring, the thickness of gain medium and feedback length is …

Go to article

Integrated Optical Spr (Surface Plasmon Resonance) Sensor Based On Optoelectronic Platform, Hyungseok Bang Jan 2008

Integrated Optical Spr (Surface Plasmon Resonance) Sensor Based On Optoelectronic Platform, Hyungseok Bang

Electronic Theses and Dissertations

Current major demands in SPR sensor development are system miniaturization and throughput improvement. Structuring an array of integrated optical SPR sensor heads on a semiconductor based optoelectronic platform could be a promising solution for those issues, since integrated optical waveguides have highly miniaturized dimension and the optoelectronic platform enables on-chip optical-to-electrical signal conversion. Utilizing a semiconductor based platform to achieve optoelectronic functionality poses requirements to the senor head; the sensor head needs to have reasonably small size while it should have reasonable sensitivity and fabrication tolerance. This research proposes a novel type of SPR sensor head and demonstrates a fabricated …

Go to article

Extended Focus Range High Resolution Endoscopic Optical Coherence Tomography, Kye-Sung Lee Jan 2008

Extended Focus Range High Resolution Endoscopic Optical Coherence Tomography, Kye-Sung Lee

Electronic Theses and Dissertations

Today, medical imaging is playing an important role in medicine as it provides the techniques and processes used to create images of the human body or parts thereof for clinical purposes (medical procedures seeking to reveal, diagnose or examine disease) or medical science (including the study of normal anatomy and function). Modalities are developing over time to achieve the highest possible resolution, speed of image acquisition, sensitivity, and specificity. In the past decade, advances in optics, fiber, as well as laser technology have enabled the development of noninvasive optical biomedical imaging technology that can also be applied to endoscopy to …

Go to article

Improved Duct Systems Task Report With Stagegate 2 Analysis, Florida Solar Energy Center, Neil Moyer Dec 2007

Improved Duct Systems Task Report With Stagegate 2 Analysis, Florida Solar Energy Center, Neil Moyer

FSEC Energy Research Center®

The Building America Industrialized Housing Partnership's work with two industry partners, Cavalier Homes and Southern Energy Homes, in constructing and evaluating prototype interior duct systems will be summarized. Issues of energy performance, comfort, DAPIA approval, manufacturability and cost will be addressed. A stage gate 2 analysis will address the current status of project showing that there are still refinements needed to the process of incorporating all of the ducts within the air and thermal boundaries of the envelope.

Go to article

First Prev Next Last