Engineering Commons^™

Physical Properties Of Wave Scattering By Chiral Periodic Structure, Xiaomin Yang

Electronic Theses and Dissertations

Attention has been focused on electromagnetic chirality and its potential applications to microwave, millimeter wave and optical wave devices. In this work, wave propagation through a chiral periodic structure with arbitrary shape is investigated. Although perturbation theory and coupled-mode theory have been used to analyze chiral periodic structure, those are approximate methods and can only be used for low frequency applications. In this work, the rigorous mode-matching method is used to solve the problem. Staircase approximation is introduced to change the curved structure to a multilayer structure. The field solutions in the uniform air regions and unbounded air-chiral periodic array …

Design Of Sea Water Heat Exchanger For Miniature Vapor Compression Cycle, James Hughes

Electronic Theses and Dissertations

Recent advances in the development of miniature vapor compression cycle components have created unique opportunities for heating and cooling applications, specifically to human physiological requirements that arise in extreme environments. Diving in very cold water between 1.7 and 5°C requires active heating because passive thermal insulation has proven inadequate for long durations. To maintain diver mobility and cognitive performance, it is desirable to provide 250 to 300 W of heat from an untethered power source. The use of a miniature vapor compression cycle reduces the amount of power (batteries or fuel cell) that the diver must carry by 2.5 times …

Silicon Carbide And Agile Optics Based Sensors For Power Plant Gas Turbines, Laser Beam Analysis And Biomedicine, Mumtaz Sheikh

Electronic Theses and Dissertations

Proposed are novel sensors for extreme environment power plants, laser beam analysis and biomedicine. A hybrid wireless-wired extreme environment temperature sensor using a thick single-crystal Silicon Carbide (SiC) chip embedded inside a sintered SiC probe design is investigated and experimentally demonstrated. The sensor probe employs the SiC chip as a Fabry-Perot (FP) interferometer to measure the change in refractive index and thickness of SiC with temperature. A novel temperature sensing method that combines wavelength-tuned signal processing for coarse measurements and classical FP etalon peak shift for fine measurements is proposed and demonstrated. This method gives direct unambiguous temperature measurements with …

Droplet Flows In Microchannels Using Lattice Boltzmann Method, Amit Gupta

Electronic Theses and Dissertations

Microelectromechanical systems (MEMS) have widespread applications in medical, electronical and mechanical devices. These devices are characterized by the smallest dimension which is at least one micrometer and utmost one millimeter. Rapid progress in the manufacture and utilization of these microdevices has been achieved in the last decade. Current manufacturing techniques of such devices and channels include surface silicon micromachining; bulk silicon micromachining; lithography; electrodeposition and plastic molding; and electrodischarge machining (EDM). In recent years, electrostatic, magnetic, electromagnetic and thermal actuators, valves, gears and diaphragms of dimensions of hundred microns or less have been fabricated successfully. Sensors have been manufactured that …

Study Of The Effects Of Sodium And Absorber Microstructure For The Development Of Cuin1-Xgaxse2-Ysy Thin Film Solar Cell Using An Alternative Selenium Precursor, Vinaykumar Hadagali

Electronic Theses and Dissertations

Thin film solar cells have the potential to be an important contributor to the world energy demand in the 21st century. CuInGaSe2 thin film solar cells have achieved the highest efficiency among all the thin film technologies. A steady progress has been made in the research and development of CuInSe2 based thin film solar cells. However, there are many issues that need to be addressed for the development of CuInSe2 based thin films solar cells. High price of PV modules has been a biggest factor impeding the growth of photovoltaic modules for terrestrial application. This thesis tries to address the …

Physical Ergonomic And Mental Workload Factors Of Mobile Learning Affecting Performance Of Adult Distance Learners: Student Pers, Rochelle Jones

Electronic Theses and Dissertations

Distance education is the fastest growing educational modality because of advances information technology has made over the past 25 years. Adult learners have become the fastest growing population in distance education. Adult learners, through technical tools and devices they use on the job, have become more digitally literate and mobile, making the ability to access class work on the go a necessity. Mobile learning or m-learning (learning that uses wireless, portable, mobile computing, and communication devices) is becoming an extension of distance learning, providing a channel for students to learn, communicate, and access educational material outside the traditional classroom environment. …

A Direct Compensator Profile Optimization Approach For Intensity Modulated Radiation Treatment Planning, Kevin Erhart

Electronic Theses and Dissertations

Radiation therapy accounts for treatment of over one million cancer patients each year in the United States alone, and its use will continue to grow rapidly in the coming years. Recently, many important advancements have been developed that greatly improve the outcomes and effectiveness of this treatment technique, the most notable being Intensity Modulated Radiation Therapy (IMRT). IMRT is a sophisticated treatment technique where the radiation dose is conformed to the tumor volume, thereby sparing nearby healthy tissue from excessive radiation dose. While IMRT is a valuable tool in the planning of radiation treatments, it is not without its difficulties. …

Efficient Techniques For Relevance Feedback Processing In Content-Based Image Retrieval, Danzhou Liu

Electronic Theses and Dissertations

In content-based image retrieval (CBIR) systems, there are two general types of search: target search and category search. Unlike queries in traditional database systems, users in most cases cannot specify an ideal query to retrieve the desired results for either target search or category search in multimedia database systems, and have to rely on iterative feedback to refine their query. Efficient evaluation of such iterative queries can be a challenge, especially when the multimedia database contains a large number of entries, and the search needs many iterations, and when the underlying distance measure is computationally expensive. The overall processing costs, …

Learning Semantic Features For Visual Recognition, Jingen Liu

Electronic Theses and Dissertations

Visual recognition (e.g., object, scene and action recognition) is an active area of research in computer vision due to its increasing number of real-world applications such as video (image) indexing and search, intelligent surveillance, human-machine interaction, robot navigation, etc. Effective modeling of the objects, scenes and actions is critical for visual recognition. Recently, bag of visual words (BoVW) representation, in which the image patches or video cuboids are quantized into visual words (i.e., mid-level features) based on their appearance similarity using clustering, has been widely and successfully explored. The advantages of this representation are: no explicit detection of objects or …

Water Vapor And Carbon Dioxide Species Measurement In Narrow Channels, Derek Lambe

Electronic Theses and Dissertations

A novel method has been implemented for measuring the concentration of gas species, water vapor and carbon dioxide, within a narrow channel flow field non-invasively using tunable diode laser absorption spectroscopy (TDLAS) in conjunction with a laser modulated at a high frequency [Wavelength Modulation Spectroscopy (WMS)] tuned to the ro-vibrational transition of the species. This technique measures the absorption profile which is a strong function of the species concentration across short path lengths and small time spans, as in PEM fuel cells during high load cycles. This method has been verified in a transparent circular flow 12 cm path length …

Realnav: Exploring Natural User Interfaces For Locomotion In Video Games, Brian Williamson

Electronic Theses and Dissertations

We present an exploration into realistic locomotion interfaces in video games using spatially convenient input hardware. In particular, we use Nintendo Wii Remotes to create natural mappings between user actions and their representation in a video game. Targeting American Football video games, we used the role of the quarterback as an exemplar since the game player needs to maneuver effectively in a small area, run down the field, and perform evasive gestures such as spinning, jumping, or the "juke". In our study, we developed three locomotion techniques. The first technique used a single Wii Remote, placed anywhere on the user's …

New Computational Approaches For Multiple Rna Alignment And Rna Search, Daniel Deblasio

Electronic Theses and Dissertations

In this thesis we explore the the theory and history behind RNA alignment. Normal sequence alignments as studied by computer scientists can be completed in O(n2) time in the naive case. The process involves taking two input sequences and finding the list of edits that can transform one sequence into the other. This process is applied to biology in many forms, such as the creation of multiple alignments and the search of genomic sequences. When you take into account the RNA sequence structure the problem becomes even harder. Multiple RNA structure alignment is particularly challenging because covarying mutations make sequence …

Reaction Velocities In Free Standing Aluminum And Cooper Oxide This Films, Matthew Erickson

Electronic Theses and Dissertations

In this work we investigate the reaction propagation velocity of aluminum and copper oxide Metastable Intermolecular Composites (MIC's). All samples were deposited in a magnetron sputtering system using 2 aluminum targets and 2 copper targets. The copper is sputtered in an oxygen rich environment in order to obtain copper oxide rich films. Three different layer structures are used for various measurements that are composed of alternating 20 layer pairs, 30 layer pairs, and 40 layer pairs. All layer pairs maintain a constant total thickness of 3.2 microns. Each layer structure can be prepared independent of a substrate and is measured …

Wavefront Sensor For Eye Aberrations Measurements, Costin Curatu

Electronic Theses and Dissertations

Ocular wavefront sensing is vital to improving our understanding of the human eye and to developing advanced vision correction methods, such as adaptive optics, customized contact lenses, and customized laser refractive surgery. It is also a necessary technique for high-resolution imaging of the retina. The most commonly used wavefront sensing method is based on the Shack-Hartmann wavefront sensor. Since Junzhong Liang's first application of Shack-Hartmann wavefront sensing for the human eye in 1994, the method has quickly gained acceptance and popularity in the ophthalmic industry. Several commercial Shack-Hartmann eye aberrometers are currently available. While the existing aberrometers offer reasonable measurement …

Optical Nonlinear Interactions In Dielectric Nano-Suspensions, Ramy El-Ganainy

Electronic Theses and Dissertations

This work is divided into two main parts. In the first part (chapters 2-7) we consider the nonlinear response of nano-particle colloidal systems. Starting from the Nernst-Planck and Smoluchowski equations, we demonstrate that in these arrangements the underlying nonlinearities as well as the nonlinear Rayleigh losses depend exponentially on optical intensity. Two different nonlinear regimes are identified depending on the refractive index contrast of the nanoparticles involved and the interesting prospect of self-induced transparency is demonstrated. Soliton stability is systematically analyzed for both 1D and 2D configurations and their propagation dynamics in the presence of Rayleigh losses is examined. We …

Wavelength-Division-Multiplexed Transmission Using Semiconductor Optical Amplifiers And Electronic Impairment Compensation, Xiaoxu Li

Electronic Theses and Dissertations

Over the last decade, rapid growth of broadband services necessitated research aimed at increasing transmission capacity in fiber-optic communication systems. Wavelength division multiplexing (WDM) technology has been widely used in fiber-optic systems to fully utilize fiber transmission bandwidth. Among optical amplifiers for WDM transmission, semiconductor optical amplifier (SOA) is a promising candidate, thanks to its broad bandwidth, compact size, and low cost. In transmission systems using SOAs, due to their large noise figures, high signal launching powers are required to ensure reasonable optical signal-to-noise ratio of the received signals. Hence the SOAs are operated in the saturation region and the …

Gabor Domain Optical Coherence Microscopy, Supraja Murali

Electronic Theses and Dissertations

Time domain Optical Coherence Tomography (TD-OCT), first reported in 1991, makes use of the low temporal coherence properties of a NIR broadband laser to create depth sectioning of up to 2mm under the surface using optical interferometry and point to point scanning. Prior and ongoing work in OCT in the research community has concentrated on improving axial resolution through the development of broadband sources and speed of image acquisition through new techniques such as Spectral domain OCT (SD-OCT). In SD-OCT, an entire depth scan is acquired at once with a low numerical aperture (NA) objective lens focused at a fixed …

Nonlinear Femtosecond Near Infrared Laser Structuring In Oxide Glasses, Arnaud Royon

Electronic Theses and Dissertations

Three-dimensional femtosecond laser structuring has a growing interest because of its ease of implementation and the numerous possible applications in the domain of photonic components. Structures such as waveguides, diffraction gratings, optical memories or photonic crystals can be fabricated thanks to this technique. Its use with oxide glasses is promising because of several advantages; they are resistant to flux and ageing, their chemical composition can easily be changed to fit the well-defined requirements of an application. They can already be found in Raman amplifiers, optical fibers, fiber lasers, and other devices. This thesis is based on two axes. The first …

Design And Fabrication Of Space Variant Micro Optical Elements, Pradeep Srinivasan

Electronic Theses and Dissertations

A wide range of applications currently utilize conventional optical elements to individually transform the phase, polarization, and spectral transmission/reflection of the incident radiation to realize the desired system level function. The material properties and the feasibility of fabrication primarily impact the device and system functionality that can be realized. With the advancement in micro/nano patterning, growth, deposition and etching technology, devices with novel and multiplexed optical functionalities have become feasible. As a result, it has become possible to engineer the device response in the near and far field by controlling the phase, polarization or spectral response at the micro scale. …

Femtosecond Laser Written Volumetric Diffractive Optical Elements And Their Applications, Jiyeon Choi

Electronic Theses and Dissertations

Since the first demonstration of femtosecond laser written waveguides in 1996, femtosecond laser direct writing (FLDW) has been providing a versatile means to fabricate embedded 3-D microstructures in transparent materials. The key mechanisms are nonlinear absorption processes that occur when a laser beam is tightly focused into a material and the intensity of the focused beam reaches the range creating enough free electrons to induce structural modification. One of the most useful features that can be exploited in fabricating photonic structures is the refractive index change which results from the localized energy deposition. The laser processing system for FLDW can …

A Gasoline Demand Model For The United States Light Vehicle Fleet, Diana Rey

Electronic Theses and Dissertations

The United States is the world's largest oil consumer demanding about twenty five percent of the total world oil production. Whenever there are difficulties to supply the increasing quantities of oil demanded by the market, the price of oil escalates leading to what is known as oil price spikes or oil price shocks. The last oil price shock which was the longest sustained oil price run up in history, began its course in year 2004, and ended in 2008. This last oil price shock initiated recognizable changes in transportation dynamics: transit operators realized that commuters switched to transit as a …

Energy Conservation In The Trinidad Tourist Industry Training Program, Florida Solar Energy Center, William Young

FSEC Energy Research Center®

This Final Report summarizes the work performed by the Florida Solar Energy Center/University of Central Florida on the contract entitled "Energy Conservation in the Trinidad Tourist Industry Training Program". This program was performed for the Ministry of Tourism, Trinidad and Tobago, WI. (MoTTT) for the period September 1 to November 1, 2008. The MoTTT established a program for the tourist industry to facilitate learning about energy conservation and renewable energy technologies appropriate for resort applications on the Island of Trinidad. The Florida Solar Energy Center provided assistance through consulting, in education about energy technologies. FSEC modified existing energy training courses …

Green And High Performance Factory Crafted Housing, Florida Solar Energy Center, Stephanie Thomas-Rees

FSEC Energy Research Center®

In the U.S., factory-built housing greater than 400 square feet is built either to the U.S. Department of Housing and Urban Development (HUD) code for mobile homes or site-built codes for modular housing. During the last few years, as the production of HUD code housing has dwindled, many leading edge factory builders have started building modular homes to compete with site-built housing and stay in business. As part of the Building America Industrialized Housing Partnership (BAIHP) we have assisted in the design and construction of several 'green' and high performance modular homes that Palm Harbor Homes, Florida Division (PHH) has …

Energy Impacts Of Various Residential Mechanical Ventilation Strategies, Florida Solar Energy Center, Robin Vieira

FSEC Energy Research Center®

The Building America program has been working with home builders for more than a decade using a variety of strategies for bringing fresh air into the homes. Many of these strategies utilize the central air handler fan from the HVAC system to ventilate when the system runs. Controllers can be purchased to force the air to enter for minimum periods of time or to shut off outside air dampers after some period of runtime. EnergyGauge USA, a detailed hourly residential simulation program, has been modified to simulate the various runtime strategies, as well as supply- or exhaust-only ventilation strategies and …

An Overview Of Building America Industrialized Housing Partnership (Baihp) Activities In Hot-Humid Climates, Florida Solar Energy Center, Subrato Chandra

FSEC Energy Research Center®

BAIHP (www.baihp.org ) conducts systems research and technical assistance activities for new housing. Hot-humid climate efforts described here include:

Systems research: NightCool – A hybrid cooling and dehumidification strategy employing radiative cooling and desiccant materials. Interior Duct Systems in Manufactured Houses – Tests are ongoing in an occupied prototype home in Alabama and the FSEC manufactured housing lab. Ventilation and Dehumidification – A new strategy has been developed to hook up a whole-house dehumidifier so that it only runs when the air conditioning compressor is off. Plug Load Reduction – Whole house feedback devices and security system based plug load …

Research Results From A Few Alternate Methods Of Interior Duct Systems In Factory Built Housing Located In The Hot Humid Climate, Florida Solar Energy Center, Neil Moyer

FSEC Energy Research Center®

The U.S. Department of Energy's (DOE) Building America Industrialized Housing Partnership (BAIHP) has collaborated with two of its industry partners to work on a portion of the project that relates to the construction and evaluation of prototype interior duct systems. In 2006, work began on a duct system design that would locate the entire length of duct work within the air and thermal barriers of the envelope. One of these designs incorporated a high-side supply register that connects to the conventional floor duct. The other design utilized a single soffit located within the conditioned space at the marriage line. The …

Assessment Of The Effectiveness And Energy Efficiency Of Humidity Control Approaches In Vacant Florida Homes, Florida Solar Energy Center, James Cummings

FSEC Energy Research Center®

In a hot and humid climate such as Florida, 'snowbirds' that leave their homes for extended summer periods need guidance on effective and energy efficient methods of humidity control. Experiments were performed in seven residences to evaluate various approaches to humidity control, including providing no mechanical system control. A humidity target was identified to maintain indoor relative humidity (RH) at 65% or lower most of the time. Providing no mechanical conditioning (letting the building 'float') yields relative humidity at 65% or below during hot and sunny weather in some homes, but not during cloudy weather. Setting the AC system thermostat …

Case Study Of An Innovative Hvac System With Integral Dehumidifier, Florida Solar Energy Center, Richard Raustad

FSEC Energy Research Center®

In most applications, heating, ventilating, and air conditioning (HVAC) equipment is controlled to maintain an indoor dry-bulb set point temperature. Moisture removal by the HVAC system is considered to be an operational byproduct. During summer months, the operation of the HVAC system is usually sufficient to meet both the sensible and latent cooling loads. However, during other times of the year when sensible loads are reduced, the moisture load can be significantly higher than the available moisture removal capacity of the air conditioning system. This can lead to elevated indoor relative humidity levels and an uncomfortable indoor environment. In many …

Energy Performance Aspects Of A Florida Green Roof, Part 2, Florida Solar Energy Center, Jeffrey Sonne

FSEC Energy Research Center®

This monitored study is an evaluation of summer and winter energy performance aspects of a green roof on a 2-story central Florida university building addition that was completed in 2005. An earlier report on this study was published through the 2006 Symposium on Improving Building Systems in Hot and Humid Climates. This report reviews these earlier results and provides second-summer results which show significant performance improvements for the green roof compared with the first summer results.

Ac System Equipment Specification, Installation And Operational Options For Improved Indoor Humidity Control, Florida Solar Energy Center, Don B. Shirey Iii

FSEC Energy Research Center®

High-efficiency home designs have significantly reduced sensible cooling loads, and some building codes and IAQ standards have begun requiring continuous outdoor ventilation air. These trends have led to an increased prevalence of high indoor humidity conditions (Rudd and Henderson 2007). This paper presents a summary of low-cost or no-cost equipment selection and operation options for conventional residential air-conditioning equipment than can result in lower indoor humidity levels. These options should be evaluated and employed to the extent possible prior to considering the added first cost and operating costs of separate dehumidification equipment.