Engineering Commons^™

Computational Design Of The Electrical And Mechanical Performance Of Steerable Mems Antennas, Morgan Andrew Roddy

Graduate Theses and Dissertations

This thesis describes the origins, improvements, and variations of a broadband microwave antenna that can be beam-steered by a micro-electromechanical system (MEMS). The steerable MEMS antenna of this work was comprised of a planar antenna on top of a Silicon membrane. The membrane is etched to create a gimbal hinge structure and a platform which supported the antenna and gave it one or two degrees of freedom of rotation. The antennas presented were broadband and fed by a coplanar waveguide (CPW) transmission line which traversed the hinge structure. The antenna's orientation in space was designed to be changed through electrostatic …

A Characterization And Measurement System For Propylene Glycol Properties (Means Of Attitude Control In Space), Abdoul Maiga

Mechanical Engineering Undergraduate Honors Theses

Recently, engineers have been able to design smaller satellites called Nano-satellites. Nano-satellites (1-10kg) also known as “Cube Sat” are based nominally on multiples of a unit cube of 10 centimeters on each side. The basic cube shape is known as 1U CubeSat. A major obstacle when designing the nano-satellites is to choose a propulsion system that would be safe, effective, low cost, and could easily function with a resistojet. The proposed system uses Propylene Glycol (C3H8O2) as a safe propellant for a resistojet. In order to predict the behavior of the propellant, the property to be characterized is its surface …

Evaluation Of Shock Induced Spallation In Nanocrystalline Copper, Chase Philpot

Mechanical Engineering Undergraduate Honors Theses

This research uses atomistic simulations to examine the behavior of nanocrystalline Cu under impact at ballistic speeds. The advantage of using atomistic simulations to study shock induced deformation is that a real-time picture of the evolution of the microstructure can be attained, whereas experimentally this is not possible. Specifically, molecular dynamics simulations are used to build models of the material and run the simulations. Six cases are explored: Single crystal Cu loaded along the <100>, <110>, and <111> directions, and nanocrystalline samples with average grain diameters of 5, 10, and 15 nm. The target to flyer ratio is varied to generate …

Design Of A Pretreatment And Enzymatic Saccharification Scheme Of Understory From Managed Pine Forest For A Biochemical-Refinery Platform: The Example Of The Sweetgum Tree, Angele Djioleu

Graduate Theses and Dissertations

The possibility of using sweetgum from southern pine dominated forests as a biobased refinery feedstock was investigated. First, a baseline hydrolysis scheme for sweetgum wood and bark was designed. Sweetgum wood and bark were pretreated with 0.98% (v/v) sulfuric acid at 140°C for 30, 40, 50, 60 or 70 min and at 160°C for 30, 40, 50 or 60 min. The water insoluble solid (WIS) fraction was hydrolyzed with a cellulase enzyme cocktail. Results showed that maximum xylose and glucose yields from the wood were 82 and 86%, respectively. Similarly, the respective maximum yields of xylose and glucose from the …

The Effects Of Temperature On Indicator Species Tests For Water Quality, Maranda Guinn

Civil Engineering Undergraduate Honors Theses

This study sought to investigate the different response of two indicator species tests: Hach® PathoScreenâ„¢ Field Test and IDEXX Colilert® using the Quanti-Tray/2000® enumeration method. Both tests were carried out according to the instructions enclosed in the packages using diluted water samples taken from the secondary clarifier at the West Side Waste Water Treatment Plant in Fayetteville, AR. The tests were carried out at various temperatures in an attempt to reflect conditions that could be encountered in the field, where electricity, equipment, and expertise may not be available. The PathoScreenâ„¢ test responded adequately at a relatively wide range of temperatures, …

The Effect Of Mortar Strength On The Standard Test For Strand Bond, Cameron Murray

Civil Engineering Undergraduate Honors Theses

The prestressed industry is moving towards adopting the Standard Test for Strand Bond (STSB) to quantify the bond capacity of prestressing strand. In the test, strand is pulled through an 18 in. cylindrical casing filled with mortar. The force corresponding to the dead end displacement of 0.1 in. is recorded and this value is used to quantify strand bond. One of the concerns of the test is the requirement of a mean mortar strength of 4,500 to 5,000 psi during testing. There is concern that this 500 psi range may be too difficult to achieve. A study was conducted to …

Design And Analysis Of An Adaptive Asynchronous System Architecture For Energy Efficiency, Brent Michael Hollosi

Graduate Theses and Dissertations

Power has become a critical design parameter for digital CMOS integrated circuits. With performance still garnering much concern, a central idea has emerged: minimizing power consumption while maintaining performance. The use of dynamic voltage scaling (DVS) with parallelism has shown to be an effective way of saving power while maintaining performance. However, the potency of DVS and parallelism in traditional, clocked synchronous systems is limited because of the strict timing requirements such systems must comply with. Delay-insensitive (DI) asynchronous systems have the potential to benefit more from these techniques due to their flexible timing requirements and high modularity. This dissertation …

Titanium Aluminum Nitride Films Deposited By Ac Reactive Magnetron Sputtering: Study Of Positioning Effect In An Inverted Cylindrical Magentron Sputtering System, George C. Vandross Ii

Graduate Theses and Dissertations

TiAlN films were deposited on glass substrates by AC magnetron sputtering at 2 kW with constant Argon and Nitrogen gas flow rates to study the effects of positioning on the deposited films. The deposition system used was an ICM-10 IsoFlux cylindrical magnetron sputtering chamber. The samples were placed in different positions and tilts with respect to the location of the Titanium and Aluminum targets in the chamber. It was found that with change in position and application of tilts, deposited films acquired different physical and chemical properties. It is believed that the differences in these properties were caused by to …

On The Maintenance Modeling And Optimization Of Repairable Systems: Two Different Scenarios, Suzan Alaswad

Graduate Theses and Dissertations

The use of mathematical modeling for the purpose of analyzing and optimizing the performance of repairable systems is widely studied in the literature. In this dissertation, we study two different scenarios on the maintenance modeling and optimization of repairable systems. First, we study the long-run availability of a traditional repairable system that is subjected to imperfect corrective maintenance. We use Kijima's second virtual age model to describe the imperfect repair process. Because of the complexity of the underlying probability models, we use simulation modeling to estimate availability performance and meta-modeling to convert the reliability and maintainability parameters of the repairable …

Topics On Light-Emitting-Diode Driver Research, Jaber Hasan

Graduate Theses and Dissertations

In this dissertation, light-emitting-diode (LED) drivers are investigated for efficiency issues related to driving Red-Green-Blue (RGB) pixels and multiple LED strings in parallel. A high-efficiency digitally controlled RGB LED driver was designed for driving a 3x3 RGB LED display panel. A multiplexer was used to sense the voltage drop across the current controllers. This driver maintained a minimum drive voltage across the RGB LED pixels required to keep it in regulation leading to a reduction of unwanted power losses in the RGB LED pixels by selecting the minimum drop across the current-controllers as the reference voltage of the digital controller. …

Energy And Spectral Efficient Wireless Communications, Guoqing Zhou

Graduate Theses and Dissertations

Energy and spectrum are two precious commodities for wireless communications. How to improve the energy and spectrum efficiency has become two critical issues for the designs of wireless communication systems. This dissertation is devoted to the development of energy and spectral efficient wireless communications. The developed techniques can be applied to a wide range of wireless communication systems, such as wireless sensor network (WSN) designed for structure health monitoring (SHM), medium access control (MAC) for multi-user systems, and cooperative spectrum sensing in cognitive radio systems.

First, to improve the energy efficiency in SHM WSN, a new ultra low power (ULP) …

Thermal And Electrical Parasitic Modeling For Multi-Chip Power Module Layout Synthesis, Zihao Gong

Graduate Theses and Dissertations

This thesis presents thermal and electrical parasitic modeling approaches for layout synthesis of Multi-Chip Power Modules (MCPMs). MCPMs integrate power semiconductor devices and drive electronics into a single package. As the switching frequency of power devices increases, the size of the passive components are greatly reduced leading to gains in efficiency and cost reduction. In order to increase switching frequency, electrical parasitics in MCPMs need to be reduced through tighter electronic integrations and smaller packages. As package size is decreased, temperature increases due to less heat dissipation capability. Thus, it is crucial to consider both thermal and electrical parasitics in …

Study Of Current Optocoupler Techniques And Applications For Isolation Of Sensing And Control Signals In Dc-Dc Converters, Jake Williams

Graduate Theses and Dissertations

There is a need for power switches that can operate at high voltage, high temperature, and high switching frequencies with low losses. Power switches fabricated from wide bandgap materials such as silicon carbide (SiC) or gallium nitride (GaN) can outperform conventional silicon switches due to material property advantages. Another common problem in grid-connected applications is the need for high voltage-isolation of gate drivers and control circuitry while operating efficiently at the high switching frequencies, high power density, and high temperatures made possible by wide bandgap devices. Transformers cannot operate at the temperatures of these wide bandgap devices and a new …

Refractive Index Chemical Sensing With Noble Metal Nanoparticles, Phillip Blake

Graduate Theses and Dissertations

Chemical sensing is a key component in modern society, especially in engineering applications. Because of their widespread impact, improvements to chemical sensors are a significant area of research. One class of sensors, plasmonic sensors, is being heavily researched because of their ability to detect low levels of analyte in near real time without destroying the analyte. This work studies a new class of plasmonic sensor that utilizes diffractive coupling to improve sensor performance. Specifically, this work outlines the first study of diffractive coupling sensors with typical nanoparticle shapes. Sensitivity of this new class of sensor is directly compared to typical …

The Development And Packaging Of A High-Density, Three-Phase, Silicon Carbide (Sic) Motor Drive, Jared Hornberger

Graduate Theses and Dissertations

Technology advances within the power electronics field are resulting in systems characterized by higher operating efficiencies, reduced footprint, minimal form factor, and decreasing mass. In particular, these attributes and characteristics are being inserted into numerous consumer applications, such as light-emitting diode lighting, compact fluorescent lighting, smart phones, and tablet PCs, to industrial applications that include hybrid, electric, and plug-in electric vehicles and more electric aircraft. To achieve the increase in energy efficiency and significant reduction in size and mass of these systems, power semiconductor device manufacturers are developing silicon carbide (SiC) semiconductor technology.

In this dissertation, the author discusses the …

Optimization Of Nonlinear Switch Cells For Switching Converters, Bradley Alan Reese

Graduate Theses and Dissertations

Switch cells consist of an array of power switches and passive components which can replace the main switches alone in many power topologies, allowing reduced switching loss without altering the power topology directly. This thesis discusses the development of a switch cell topology that utilizes a saturable resonant inductor to reduce the size and power loss of the cell. Additionally, the cell transfers energy stored in the inductor into a capacitor for efficient energy storage during the cell's conduction region. This energy is then transferred back to the system when the cell turns off, thus reducing the total switching energy.

Capillary And Microchip Electrophoresis For The Monitoring Of Disease Causing Amyloid Proteins, Elizabeth Nancy Pryor

Graduate Theses and Dissertations

The detection of oligomers and aggregates formed by two amyloid proteins, insulin and amyloid-beta (AB), is of particular importance due to the role which these species play in Diabetes and Alzheimer's disease, respectively. However, existing techniques are limited in the ability to detect insulin and AB; oligomers due to the fact that these early aggregates are transient, present at low concentrations, and difficult to isolate. Improvements must be made to existing techniques or alternative techniques must be explored in order to identify and quantify the size of these oligomeric and aggregate species without disrupting their structure.

Capillary and microchip electrophoresis …

A Silicon Carbide Based Solid-State Fault Current Limiter For Modern Power Distribution Systems, Erik Darnell Johnson

Graduate Theses and Dissertations

The fault current limiter represents a developing technology which will greatly improve the reliability and stability of the power grid. By reducing the magnitude of fault currents in distribution systems, fault current limiters can alleviate much of the damage imposed by these events. Solid-state fault current limiters in particular offer many improved capabilities in comparison to the power system protection equipment which is currently being used for fault current mitigation. The use of silicon carbide power semiconductor devices in solid-state fault current limiters produces a system that would help to advance the infrastructure of the electric grid.

A solid-state fault …

Plasmonic And Photonic Designs For Light Trapping In Thin Film Solar Cells, Liming Ji

Graduate Theses and Dissertations

Thin film solar cells are promising to realize cheap solar energy. Compared to conventional wafer cells, they can reduce the use of semiconductor material by 90%. The efficiency of thin film solar cells, however, is limited due to insufficient light absorption. Sufficient light absorption at the bandgap of semiconductor requires a light path more than 10x the thickness of the semiconductor. Advanced designs for light trapping are necessary for solar cells to absorb sufficient light within a limited volume of semiconductor. The goal is to convert the incident light into a trapped mode in the semiconductor layer.

In this dissertation, …

Risk Analysis And Reliability Improvement Of Mechanistic-Empirical Pavement Design, Xingqiang Danny Xiao

Graduate Theses and Dissertations

Reliability used in the Mechanistic Empirical Pavement Design Guide (MEPDG) is a congregated indicator defined as the probability that each of the key distress types and smoothness will be less than a selected critical level over the design period. For such a complex system as the MEPDG which does not have closed-form design equations, classic reliability methods are not applicable. A robust reliability analysis can rely on Monte Carlo Simulation (MCS). The ultimate goal of this study was to improve the reliability model of the MEPDG using surrogate modeling techniques and Monte Carlo simulation.

To achieve this goal, four tasks …

Effects Of Testing Time On Anaerobic Toxicity Assessment, Omolola Atinuke Akintomide

Graduate Theses and Dissertations

Anaerobic digestion has been widely used for wastewater treatment for decades. Several Anaerobic Toxicity tests have been developed to screen wastewater for toxicity and assess the treatability of such toxicants. However, past research and reviews on Biochemical Methane Potential (BMP) test and Anaerobic Toxicity Assay (ATA) were considered in this study.

The experimental tests included ammonium-nitrogen and sodium chloride toxicity tests with varied concentration and solid retention time. These tests were designed to demonstrate the impact of ammonia- nitrogen and sodium chloride on the biological degradation process. The anaerobic test set-up includes bench-scale test reactors and respirometers used for measuring …

Magnitude And Frequency Of Floods For Rural, Unregulated Streams Of Tennessee By L-Moments Method, Hongxiang Yan

Graduate Theses and Dissertations

This study presents a regional frequency analysis of Tennessee using the well-known Bulletin-17B method standardly used in the United States and the relatively new and developing L-Moments methods. Flood frequency characteristics were defined for 416 gaging stations located primarily in rural and lightly developed areas of Tennessee. All the gaging stations have 10 or more years of record through 2006. Using the L-Moments method, the generalized extreme value distribution was identified as the most robust distribution for each of four hydrologic areas. Multiple regression equations were also calculated for estimating the flood frequency of ungaged, unregulated, rural streams in each …

The Development Of A High Performance Concrete To Store Thermal Energy For Concentrating Solar Power Plants, Emerson Esmond John

Graduate Theses and Dissertations

In recent years, due to rising energy costs as well as an increased awareness of the environmental effects of greenhouse gas emissions produced through traditional forms of energy production, there is great interest in developing alternative sources of energy. One of the most viable alternative energy sources is solar energy. In particular, concentrating solar power (CSP) technologies have been identified as an option for meeting utility needs in the U.S. Southwest. These systems are required to produce electricity not only during periods of high solar radiation but also during times of reduced radiation due to cloud cover, and even extend …

Investigating The Bond Of Prestressing Strands In Lightweight Self-Consolidating Concrete, Royce Woodrow Floyd

Graduate Theses and Dissertations

Lightweight self-consolidating concrete (LWSCC) is a relatively recent advancement in concrete technology. The reduced dead load from lightweight concrete is beneficial for precast elements and for elements where dead load is a significant portion of the total load, such as prestressed bridge girders. Self-consolidating concrete (SCC) is a specially proportioned concrete mixture that consolidates under its own weight without the need for vibration. The combination of lightweight concrete and self-consolidating behavior provides the benefits of both. Bond of prestressing steel has been a much debated topic since the 1950s. Limited data are available on the transfer and development length of …

Improved Protocols For Automated Wheelpath Crack Detection In Pavements, Daniel Patrick Byram

Graduate Theses and Dissertations

Roadway pavement distress evaluations are vital to understanding the mechanics of pavement stability, determining the distribution of rehabilitation costs, and knowing the appropriate rehabilitation strategies. Advancements in technology over the past two decades have changed the way these surveys have been performed by means of automated data collection and interpretation. More and more state agencies have invested in automated road analyzing vehicles that are able to collect high resolution images of the pavement. Fewer have adopted automated data processing software with the ability to interpret road distresses due to the common discrepancies in distress classification algorithms.

In addition to automated …

New Insights Into Disinfection Byproduct Formation And Control: Assessing Dissolved Organic Matter Diffusivity And Chemical Functionality, Ashley Pifer

Graduate Theses and Dissertations

Methods were developed for application of asymmetric flow field-flow fractionation (AF4) and fluorescence parallel factor (PARAFAC) analysis to raw and treated samples from drinking water sources to improve characterizations of dissolved organic matter (DOM) and discover DOM properties correlated to disinfection byproduct (DBP) formation potential (FP). Raw water samples were collected from a reservoir, adjusted to pH 6, 7, and 8 and subjected to (1) jar tests using aluminum sulfate (alum) and (2) treatment with magnetic ion exchange (MIEX^®) resin. Both treatments were followed by DBPFP tests at pH 7. AF4 was used to size DOM in raw …

Wheel Path Wandering Based On Field Data, Wenting Luo

Graduate Theses and Dissertations

The position and width of wheel path on a pavement lane is an important consideration in conducting pavement distress survey, especially for distinguishing longitudinal cracking from fatigue cracking. Currently, the widely used wheel path definition is derived from the LTPP distress manual with fixed width and position, in which the influence of traffic wander on wheel path was overlooked. This thesis attempts to develop a new wheel path definition based on the lateral placement investigation of heavy vehicles' wandering in the field. Generally, the factors influencing vehicle lateral placement can be divided into seven categories, but only four factors are …

Modeling The Adoption Of Identification Standards Within The Healthcare Supply Chain, Angelica Burbano

Graduate Theses and Dissertations

The adoption of identification standards and its associated technology in the healthcare supply chain has been slow over the past twenty five years, despite the evidence of the benefits that can be achieved. The widespread use of identification standards in the form of barcode labeled medical products can contribute to the reduction of point of care errors and can increase the efficiency of healthcare supply chain related processes. This research is focused on the analysis of the adoption of identification standards in the healthcare supply chain with a particular focus on the healthcare provider adoption challenges. The research is divided …

Characterization And Quantification Of Monomers, Oligomers, And By-Products From Xylan During Biomass Pretreatment, Ching-Shuan Lau

Graduate Theses and Dissertations

Biomass pretreatment generates inhibitory products, which reduce the overall yield of xylose for ethanol production. Understanding of hemicellulose depolymerization into xylose is essential to identify the pretreatment conditions that maximize xylose formation, but minimize the generation of these inhibitory products, such as formic acid and furfural. Thus, the goal of this project is to understand how dilute acid pretreatment parameters affect hemicellulose depolymerization, maximize xylose concentrations, and minimize by-products formation.

To progress towards this goal, rates and mechanisms of hemicellulose release must be determined. Birchwood xylan was used as the starting material to produce xylose oligomers. The hydrolyzed birchwood xylan …

Locating And Protecting Facilities Subject To Random Disruptions And Attacks, Hugh Medal

Graduate Theses and Dissertations

Recent events such as the 2011 Tohoku earthquake and tsunami in Japan have revealed the vulnerability of networks such as supply chains to disruptive events. In particular, it has become apparent that the failure of a few elements of an infrastructure system can cause a system-wide disruption. Thus, it is important to learn more about which elements of infrastructure systems are most critical and how to protect an infrastructure system from the effects of a disruption. This dissertation seeks to enhance the understanding of how to design and protect networked infrastructure systems from disruptions by developing new mathematical models and …