Engineering Commons^™

Displacement Derived Energy Levels For Harvard Miniature Compaction, Ana Laura Errigo, Julia Loshelder

Civil Engineering Undergraduate Honors Theses

Previously, the amount of energy provided by the Harvard Miniature tamper was adjusted by changing the number of blows per lift or the number of lifts or was not adjusted at all. However, this research was conducted to investigate the effect of adjusting the displacement of the spring (increased or decreased) to change the potential energy of the spring and therefore change the compacive effort with a specific type of soil. Thus, the objective was to match the compaction energies using the Harvard miniature method with the compaction energies obtained using the Proctor method. Specifically, the goal was to show …

Microextrusion 3d Printing Of Optical Waveguides And Microheaters, Edidiong Nseowo Udofia

Graduate Theses and Dissertations

The drive for smaller and more compact devices presents several challenges in materials and fabrication strategies. Although photolithography is a well-developed method for creating microdevices, the disparate requirements in fabrication strategies, material choices, equipment and process complexities have limited its applications. Microextrusion printing (μEP) provides a promising alternative for microfabrication. Compared to the traditional techniques, the attractions lie in the wide range of printable material choice, greater design freedom, fewer processing steps, lower cost for customized production, and the plurality of compatible substrates. However, while extrusion-based 3D printing processes have been successfully applied at the macroscale, this seeming simplicity belies …

Development Of A Multimode Instrument For Remote Measurements Of Unsaturated Soil Properties, Sean Elliott Salazar

Graduate Theses and Dissertations

The hydromechanical behavior of soil is governed by parameters that include the moisture content, soil matric potential, texture, and the mineralogical composition of the soil. Remote characterization of these and other key properties of the soil offers advantages over conventional in situ or laboratory-based measurements: information may be acquired rapidly over large, or inaccessible areas; samples do not need to be collected; and the measurements are non-destructive. A field-deployable, ground-based remote sensor, designated the Soil Observation Laser Absorption Spectrometer (SOLAS), was developed to infer parameters of bare soils and other natural surfaces over intermediate (100 m) and long (1,000 m) …

The Development Of Initial Asphalt Mixture Acceptance Criteria Using The Scb Test And The I-Fit Test, Nathan Delman Parnell

Graduate Theses and Dissertations

Cracking has become the primary asphalt pavement distress in Arkansas. Arkansas along with other states have implemented a test to measure rutting resistance. This paper presents research to implement a cracking resistance test to further modify the Superpave volumetric asphalt mixture design method in Arkansas. The Illinois Flexibility Index Test (I-FIT) was the test chosen to analyze for this research. Two aging methods were tested, a short term oven aging (AASHTO R30 ST) and a long term oven aging (NCAT) method. Six asphalt mixtures were selected to be tested. The mixtures testes were recreated from Arkansas Department of Transportation (ARDOT) …

Generation Of A Ccl2 Knockout Using Crispr/Cas9 And Lipid Mediated Transfection In Ct-26 Murine Colon Carcinoma Cells, Emma Sullivan

Biomedical Engineering Undergraduate Honors Theses

CCL2 is an inflammatory mediator that is released by tumor cells to activate and direct immune cell species, especially macrophages, to inflammatory sites within the body. The goal of this project was to successfully generate knockout the CCL2 ligand gene using a CRISPR/Cas9 complex delivered via lipid mediated transfection. The sgRNA and Cas9 mRNA were introduced into the cells via lipid-mediated transfection. The cells were incubated for 4 days, before being analyzed using PCR and gel electrophoresis. We expected to see one band on the first gel and two bands on the second gel. Two bands appeared on the first …

Dynamic Prediction Of Treatment Outcomes For Recurrent Tuberculosis Patients, Nicole Hayes

Industrial Engineering Undergraduate Honors Theses

Tuberculosis (TB) is a disease that affects people around the world, especially people in underdeveloped countries. TB is one of the top ten causes of death globally so improvement in understanding diagnosis and treatment of TB affected patients could lead to major improvements in world health. This thesis research evaluated relapse patients specifically, deeming a relapse patient as one who has either been cured or completed their last treatment and then is diagnosed with TB again.

This research uses dynamic predictive modeling, based upon the random forest algorithm, to predict treatment outcomes for recurrent TB patients using demographic and follow-up …

Development Of A Ground-Based Aerial-Tracking Instrument For Open-Path Spectroscopy To Monitor Atmospheric Constituents, Haden Hodges

Civil Engineering Undergraduate Honors Theses

A ground-based aerial-tracking instrument, known as the Ground Tracker, designed to provide spectral data to quantify greenhouse gases is under development. The Ground Tracker includes an Optical System including a high power rifle scope, video camera, and spectrometer used to locate an active light source from the Emitter, and collect spectral data by utilizing an actuating mirror. The implementation of this instrument could be made low cost by utilizing existing weather balloon infrastructure to allow the Emitter to be placed into the lower stratosphere. The recovery of the emitter will be possible by tracking the GPS coordinates. Weather balloon instrument …

A Simulation Tool For Evaluating The Environmental Impacts Of Management Scenarios For Modern Broiler Production Systems, Martin Andrew Christie

Graduate Theses and Dissertations

The purpose of this work is to provide a simulation tool that allows broiler production practitioners and researchers to simulate the effects of farm design and management practices on resource consumption and environmental impacts. This tool allows the user to design unique farms and simulates on farm processes required to raise broiler chicks to a marketable age. The use can input data such as farm location, broiler breed, flock size, ration type, barn dimensions, and climate control equipment specifications. The algorithms used to simulate broiler breed specific feed intake, broiler weight gain, and other on farm processes such as heating, …

Backstepping Control And Transformation Of Multi-Input Multi-Output Affine Nonlinear Systems Into A Strict Feedback Form, Khalid Salim D. Alharbi

Graduate Theses and Dissertations

This dissertation presents an improved method for controlling multi-input multi-output affine nonlinear systems. A method based on Lie derivatives of the system's outputs is proposed to transform the system into an equivalent strict feedback form. This enables using backstepping control approaches based on Lyapunov stability and integrator backstepping theory to be applied. The geometrical coordinate transformation of multi-input multi-output affine nonlinear systems into strict feedback form has not been detailed in previous publications. In this research, a new approach is presented that extends the transformation process of single-input single-output nonlinear. A general algorithm of the transformation process is formulated. The …

Toolpath Planning Methodology For Multi-Gantry Fused Filament Fabrication 3d Printing, Hieu Trung Bui

Graduate Theses and Dissertations

Additive manufacturing (AM) has revolutionized the way industries manufacture and prototype products. Fused filament fabrication (FFF) is one of the most popular processes in AM as it is inexpensive, requires low maintenance, and has high material utilization. However, the biggest drawback that prevents FFF printing from being widely implemented in large-scale production is the cycle time. The most practical approach is to allow multiple collaborating printheads to work simultaneously on different parts of the same object. However, little research has been introduced to support the aforementioned approach. Hence a new toolpath planning methodology is proposed in this paper. The objectives …

Automatic Methods To Enhance The Quality Of Colonoscopy Video, Nidhal Kareem Shukur Azawi

Graduate Theses and Dissertations

Colonoscopy is a form of endoscopy because it uses colonoscopy device to help the doctor to understand a colon patient. Enhancing the quality of Colonoscopy images is a challenge because of the wet and dynamic environment inside the colon causes many problems even the colonoscope devise has a good quality. Some of these problems are blurriness, specular highlights shiny areas.

In this work, different kinds of techniques have been investigated in order to improve the quality of colonoscopy images. Also, variety of preprocessing approaches (removing bad images, resizing images, median filtration with and without image resizing) have been conducted to …

Polarization Properties Of Airy And Ince-Gaussian Laser Beams, Sean Michael Nomoto

Graduate Theses and Dissertations

The description of polarization states of laser light as linear, circular polarization within the paraxial scalar wave approximation is adequate for most applications. However, this description falls short when considering laser light as an electromagnetic wave satisfying Maxwell's equations. An electric field with a constant unit vector for direction of the field and a space dependent complex scalar amplitude in the paraxial wave approximation does not satisfy Maxwell equations which, in general, requires all three Cartesian components of electric and magnetic fields associated for a nonzero laser beam to be nonzero.

Physical observation of passing a linearly polarized laser through …

Five-Level Flying Capacitor Converter Used As A Static Compensator For Current Unbalances In Three-Phase Distribution Systems, Rafael Franceschi

Graduate Theses and Dissertations

This thesis presents and evaluates a solution for unbalanced current loading in three-phase distribution systems. The proposed solution uses the flying capacitor multilevel converter as its main topology for an application known as Unbalanced Current Static Compensator. The fundamental theory, controller design and prototype construction will be presented along with the experimental results. The Unbalanced Current Static Compensator main objective is the balancing of the up-stream currents from the installation point to eliminate the negative- and zero-sequence currents originated by unbalanced single-phase loads.

Three separate single-phase flying capacitor converters are controlled independently using a d-q rotating reference frame algorithm to …

A Study Of Protein And Peptide-Directed Nanoparticle Synthesis For Catalytic Materials, Abdollah Mosleh

Graduate Theses and Dissertations

Nanoparticles have received much attentions due to their unique properties that makes them suitable candidates for a broad range of applications. As the size of particles decreases, their surface area-to-volume ratio would increase which is the main cause of much attention. In addition to the size, their morphologies and compositions may also play important roles for defining unique properties. Nanoparticle synthesis include both bottom-up and top-down strategies. To control the process of inorganic nanoparticles synthesis one could follow the bottom-up approach to have atom-level control over their compositions, morphologies, phases, and sizes which is the subject of this work. Due …

Bioengineering Extracellular Matrix Scaffolds For Volumetric Muscle Loss, Kevin Roberts

Graduate Theses and Dissertations

Volumetric muscle loss overwhelms skeletal muscle’s ordinarily capable regenerative machinery, resulting in fibrosis and severe functional deficits which have defied clinical repair strategies. My work spans the design and preclinical evaluation of implants intended to drive the cell community of injured muscle toward a regenerative state, as well as the development of an understanding of the molecular responses of this cell community to biomaterial interventions. I demonstrate a new class of biomaterial by leveraging the productive capacity of sacrificial hollow fiber membrane cell culture; I show specifically that unique threads of whole extracellular matrix can be isolated by solvent degradation …

Investigation Of The Effect Of Age On Regenerative Outcomes Following Treatment Of Volumetric Muscle Loss Injuries, John Taehwan Kim

Graduate Theses and Dissertations

Volumetric muscle loss (VML) is a traumatic injury in skeletal muscle resulting in the bulk loss of more than 20% of the muscle’s volume. Included in the bulk loss of muscle is the skeletal muscle niche comprised of nerve bundles, vasculature, local progenitor cells, basal lamina, and muscle fibers, overwhelming innate repair mechanisms. The hallmark of VML injury is the excessive accumulation of non-contractile, fibrotic tissue and permanent functional deficits. Though predominant in the younger demographic, the elderly population is also captured within VML injuries. There are many factors that change with aging in skeletal muscle that may further hinder …

Visualizing Ischemic Skin Flap Necrosis Through Phasor Analysis Of Autofluorescence Lifetime Images, Hallie Ramser Toomer

Graduate Theses and Dissertations

Necrotic skin flaps are difficult to predict and treat due to the lack of quantitative biomarkers. Label-free multiphoton microscopy is well suited for non-invasively monitoring skin metabolism through NAD(P)H and other intrinsic fluorophores, and offers immediate future directions for assessing necrosis in the clinic. The objective of this study was to assess whether phasor FLIM could be used to evaluate skin flap status and treatment efficacy in ex vivo skin sections. Phasor maps revealed differences in growth factor treatment and region, but changes in skin flap autofluorescence at 755nm excitation and 460nm emission were not just related to NAD(P)H. A …

Engineered Carbon-Nanocatalyst Composites And Carbon Mixed ‎Matrix Membranes ‎For Water And Wastewater Treatment ‎, Mojtaba Abolhassani

Graduate Theses and Dissertations

Carbonaceous materials such as graphene oxide, and activated ‎carbon have a wide range of ‎applications in water and wastewater treatment due to the high surface ‎area, unique structure, ‎and chemical and thermal stability. Carbon-based materials can be used as a ‎membrane, an ‎adsorbent, a support for nanomaterials, or ‎as a filler within membranes to remove contaminants ‎from water. In this research, the specific carbon materials and how their properties influence their ‎use and performance in ‎specific engineering applications is explored. ‎

Here, membrane filtration and adsorption/degradation of the water and wastewater using carbon-‎based material are investigated. The research firstly focuses …

Probabilistic Models For Order-Picking Operations With Multiple In-The-Aisle Pick Positions, Jingming Liu

Graduate Theses and Dissertations

The development of probability density functions (pdfs) for travel time of a narrow aisle lift truck (NALT) and an automated storage and retrieval (AS/R) machine is the focus of the dissertation. The multiple in-the-aisle pick positions (MIAPP) order picking system can be modeled as an M/G/1 queueing problem in which storage and retrieval requests are the customers and the vehicle (NALT or AS/R machine) is the server. Service time is the sum of travel time and the deterministic time to pick up and deposit a pallet (TPD).

Our first contribution is the development of travel time pdfs for retrieval operations …

Switching Trajectory Control For High Voltage Silicon Carbide Power Devices With Novel Active Gate Drivers, Shuang Zhao

Graduate Theses and Dissertations

The penetration of silicon carbide (SiC) semiconductor devices is increasing in the power industry due to their lower parasitics, higher blocking voltage, and higher thermal conductivity over their silicon (Si) counterparts. Applications of high voltage SiC power devices, generally 10 kV or higher, can significantly reduce the amount of the cascaded levels of converters in the distributed system, simplify the system by reducing the number of the semiconductor devices, and increase the system reliability.

However, the gate drivers for high voltage SiC devices are not available on the market. Also, the characteristics of the third generation 10 kV SiC MOSFETs …

Modification And Optimization Of Conducting Polymer-Modified, Redox-Magnetohydrodynamics (R-Mhd) Pumping For Enhanced And Sustained Microfluidics Applications, Md Foysal Zahid Khan

Graduate Theses and Dissertations

In this work, a novel microfluidic pumping approach, redox-magnetohydrodynamics (R-MHD) has improved by materials and device optimization to use in lab-on-a-chip applications. In R-MHD, magnetic flux (B) and ionic current density (j) interacts to generate body force (FB) in between active electrodes, according to the equation FB = j×B. This unique fluid pumping approach is scalable, tunable, generates flat flow profile, and does not require any channels or valves. Pumping performance, such as speed scales with the ionic current density (j) and duration depends on the total charge (Q). The ionic current density (j) results from the conversion of electronic …

Growth Of Indium Nitride Quantum Dots By Molecular Beam Epitaxy, Steven P. Minor

Graduate Theses and Dissertations

Over the last decade, the evolution of the global consciousness in response to decreasing environmental conditions from global warming and pollution has led to an outcry for finding new alternative/clean methods for harvesting energy and determining ways to minimize energy consumption. III-nitride materials are of interest for optoelectronic and electronic device applications such as high efficiency solar cells, solid state lighting (LEDs), and blue laser (Blu-ray Technology) applications. The wide range of direct band gaps covered by its alloys (0.7eV-6.2eV) best illustrates the versatility of III-nitride materials. This wide range has enabled applications extending from the ultraviolet to the near …

Energy Transformation And Conservation Investigation, Mike Jackson, Holly Haney

High School Lesson Plans

Students will use a thermoelectric generator module to analyze the relationship between thermal and electrical energies. Using data collection sensors and analysis software, students will investigate the relationship between the temperature gradient across a thermoelectric generator module and the resulting electrical potential. Students will then use their data and analysis to solve problems relating to waste thermal energy in electrical systems and communicate their work to their peers and teacher.

Different Approaches To Blurring Digital Images And Their Effect On Facial Detection, Erich-Matthew Pulfer

Computer Science and Computer Engineering Undergraduate Honors Theses

The purpose of this thesis is to analyze the usage of multiple image blurring techniques and determine their effectiveness in combatting facial detection algorithms. This type of analysis is anticipated to reveal potential flaws in the privacy expected from blurring images or, rather, portions of images. Three different blurring algorithms were designed and implemented: a box blurring method, a Gaussian blurring method, and a differential privacy-based pixilation method. Datasets of images were collected from multiple sources, including the AT&T Database of Faces. Each of these three methods were implemented via their own original method, but, because of how common they …

Very Low Power Cockcroft-Walton Voltage Multiplier For Rf Energy Harvesting Applications, Trace Langdon

Electrical Engineering Undergraduate Honors Theses

A device was required that could harvest the electromagnetic energy present in ambient radio frequency (RF) signals. A part of this device must convert the AC RF signal received by the antenna into a DC signal that can be used in an embedded application. Since the RF signal amplitude is small, it must first be amplified and rectified to become a usable signal. The Cockcroft-Walton voltage multiplier is a subsystem of the design which ideally converts a 100 mV AC signal coming from the antenna to a 350 mV DC signal. The output of the voltage multiplier is used to …

Design Of Two-Stage Operational Amplifier Using Indirect Feedback Frequency Compensation, Roderick Gomez

Electrical Engineering Undergraduate Honors Theses

This thesis work details the designing process of two silicon two-stage operational amplifiers with indirect feedback compensation and with Miller compensation technique. The main objective of this thesis is to study the advantages of indirect feedback compensation in comparison with Miller compensation and how this technique can be applied to meet certain design specifications. The operational amplifiers are designed with 130 nm Silicon Germanium CMOS process ideally for temperature range of 25°C to 300°C. The two op-amps are designed to have a DC gain of about 70 dB and 60 degrees of phase margin. The indirect feedback compensation design showed …

The Influence Of Citric Acid On Setting Time And Temperature Behavior Of Calcium Sulfoaluminate-Belite Cement, Edgar Soriano

Civil Engineering Undergraduate Honors Theses

Today the need to opt for alternative cementitious materials is growing due to environmental reasons and construction time frames that portland cement cannot always satisfy. Calcium Sulfoaluminate (CSA) cements are a strong candidate to supplement or replace portland cement in the construction field for certain applications. In the United States, CSA cement has been limited mostly to pavement repairs because of its rapid initial setting time. The chemical compound responsible for this phenomenon is the alumina. This compound and sulfate are present in larger proportions compared to portland cement. The purpose of this research is to study how the use …

Asphalt Concrete As A Flooring Material, Aleinys Villarreal

Civil Engineering Undergraduate Honors Theses

The need for having a good quality flooring has become something very important in order to enhance people’s spaces and living lifestyle. Some of the most common tile materials are cork, vinyl, concrete, and ceramic. While these four materials mentioned before are still capable materials, asphalt concrete has a distinct pattern that may be an attractive alternative to the standard tile types. To try and find solutions to these problems and give people another material option, asphalt concrete was evaluated as a flooring material.

The reason why asphalt concrete could have this new application is based on the outstanding properties …

Optical Response Analysis Of Thz Photoconductive Antenna Using Comsol Multiphysics, Jose Isaac Santos Batista

Electrical Engineering Undergraduate Honors Theses

A THz photoconductive antenna consists of antenna pads laid over a photoconductive substrate. These types of antennas are excited through the application of an optical pump (laser), which generates carriers inside the semiconductor. The acceleration and recombination of these carriers produce photocurrent that excites the antenna and generates THz pulse. This thesis focuses on analyzing the optical response of a photoconductive antenna, which consist of the interaction of the incident electric field of a laser pump with the radiating device. It develops the amplitude modulation process of a plane wave of light into a laser pump. It also takes into …

Designing, Simulating, And Layout Of An Rfic Mixer In A 130 Nm Sige Process, Logan Walz

Electrical Engineering Undergraduate Honors Theses

Wireless devices are becoming increasingly popular each day ranging from smartphones to Amazon Echo’s to wireless sensors in industry. While all of these devices are quite different in their functions and purposes, they all rely on wireless communication heavily and signal modulation techniques. One component typically seen in wireless applications like this are mixers, which are used to modulate the signal being sent and received. This thesis details the design, simulation, and layout of a radio frequency integrated circuit mixer in a 130 nanometer silicon germanium process. While the fabricated mixer did not perform to standards, many things were learned …