Engineering Commons^™

Reconfigurable Antenna With Elevation And Azimuth Beam Switching, S. Shynu, Max Ammann

Articles

A reconfigurable microstrip antenna is proposed for low-cost adaptive beam-switching applications. A small patch-slot-ring structure is used as the radiating element where an asymmetrical arrangement of p-i-n diodes is employed to switch the pattern in four directions. The antenna provides pattern switching of 65° and 45° in its fundamental mode for the elevation and azimuth planes, respectively. By maintaining the resonant frequency and beamwidth as relatively constant, beam switching is realized using a single feed point.

Power Quality In Grid Connected Renewable Energy Systems: Role Of Custom Power Devices, Shafiuzzaman Khan Khadem, Malabika Basu, Michael Conlon

Conference papers

This paper deals with the technical review of power quality problems associated with the renewable based distributed generation systems and how the custom power devices like STATCOM, DVR and UPQC play important role in power quality improvement. IEEE and IEC standard for the grid connected renewable energy systems are one of the critical point of interest for the selection of custom power devices. Special attention has been given on the compensation of reactive power, harmonic current and voltage fluctuation during the interconnected as well as islanding mode of operation. As the solar and wind are the most abundant resources therefore …

The Control Of Rotor Side And Grid Side Converters In A Dfig During Network Voltage Unbalance Conditions Using Resonant Current Controllers., Joseph Kearney, Michael Conlon, Eugene Coyle

Conference papers

This paper implements control techniques to enable improved operation of DFIG’s when subjected to the effects of network voltage unbalance conditions. The control scheme involves the integration of a resonant regulator into the PI controllers of both the rotor side and grid side converters in a DFIG. The resonant controller is tuned to twice the network frequency (2ω_e) and designed to mitigate against the oscillations in a DFIG due to network voltage unbalance conditions. The grid side converter controller also incorporates a second resonant controller tuned to three times the grid frequency (3ω_e) to alleviate the …

Measuring Variations Of Mimicry By Means Of Prosodic Cues In Task-Based Scenarios And Conversational Speech, Brian Vaughan, Celine De Looze

Other resources

Here, we address the measurement of mimicry, that is when speakers’ speech variations look like parallel patterns.

As a definition of mimicry, we often read in the literature description such as mimicry is “The situation where the observed behaviours of two inter-actants although dissimilar at the start of the interaction are moving towards behavioral matching”. These types of descriptions imply that mimicry is a linear phenomenon and that speakers tend to imitate over time. However, it can be assumed, especially when studying spontaneous speech, that there are rather phases of mimicry and non-mimicry and that mimicry should be rather …

A Linear Finite Element Acoustic Fluid-Structure Model Of Ultrasonic Angioplasty In Vivo, Mark Wylie, Garrett Mcguinness, Graham Gavin

Articles

The delivery of high-power ultrasonic energy via small diameter wire waveguides represents a new alternative therapy for the treatment of chronic totally occluded arteries (CTOs). This type of energy manifests itself as a mechanical vibration at the distal-tip of the waveguide with amplitudes of vibration up to 60 µm and at frequencies of 20- 50 kHz. Disruption of diseased tissue is reported to be a result of direct mechanical ablation, cavitation, pressure components and acoustic streaming and that ablation was only evident above the cavitation threshold. This work presents a linear finite element acoustic fluid-structure model of an ultrasonic angioplasty …

Evidence Based Evaluation Research In Engineering, Kevin Kelly

Other resources

No abstract provided.

Building A Successful Transatlantic Collaboration In Engineering/Technological Education; Lessons From A Six Year Journey, Donal Mchale, Mark Mcgrath, John Lawlor

Conference Papers

This paper reflects on key learning’s from the first six-years (2004-2010) of the development of a collaborative journey of two trans-Atlantic higher-educational institutions. It describes the progress towards building a sustainable and innovative international educational partnership in Engineering/Technological education between the Technological University Dublin,DublinIrelandandPurdue University,Indiana,USA.

In particular, the paper provides insight into the iterative stages of development of this relationship. It reflects on some of the key challenges and it recognises the critical enablers of success. It focuses on challenges and solutions in the following six important areas

(i) The partnership initiation stage. Key considerations and important enablers of future …

Rebuilding After Disaster - Engineering Lessons From The 2004 Tsunami, Liam Mccarton

Articles

On 26th December 2004 a magnitude 9 earthquake occurred off the west coast of northern Sumatra, Indonesia. The sudden and violent vertical displacement of the sea floor caused a disturbance to the overlying water column, which generated waves (tsunami) that propagated rapidly across the whole of the Indian Ocean. Typically, in open ocean waters, these waves have long wavelengths of the order of 200km and low trough to crest amplitudes. These properties allow them to conserve energy as they propagate over large distances. As the waves enter the shallower waters of coastal areas, their amplitude increases dramatically and their velocity …

An Intriguing Monument, Muiris O'Sullivan, Frank Prendergast, Geraldine Stout

Articles

No abstract provided.

Simulation Of Traffic Loading On Highway Bridges, Bernard Enright

Other resources

This work is based on weigh-in-motion measurements for approximately three million trucks obtained from sites in five European countries. Techniques have been developed, supported by photographic evidence, for filtering the measurements to identify and remove unreliable values, and for the classification of extremely heavy vehicles. The collected measurements have been used as the basis for building and calibrating a Monte Carlo simulation model for bridge loading. Two-lane traffic is simulated – either two lanes in the same direction or one lane in each direction. The model allows for vehicles that are both heavier and have more axles than in the …

Links With Canada Benefit Dit Prosthesis Research, Colm O'Kane

Articles

Colm O’Kane is a lecturer in the School of Manufacturing and Design Engineering and a member of the DIT Biomedical Device and Assistive Technology Research Group. He is currently engaged in PhD research in the field of knee prosthesis development, focused on developing optimised strategies for partial and total joint replacements used in treatment of osteoarthritis of the knee joint. This article is an account of a research scholarship sponsored by the CHC Helicopter Corporation and awarded by the Ireland Canada University Foundation (ICUF). This foundation awards annual scholarships for research visits between Ireland and Canada with the aspiration of …

Novel Ac Side P&O Maximum Power Transfer Control For Grid Connected Photovoltaic Systems, Mohamed Moin Hanif, Malabika Basu, Kevin Gaughan

Conference papers

Grid connected Photovoltaic inverters can convert PV energy into electricity with very high efficiencies. Power from the PV panels fluctuates depending on various weather conditions. PV inverters usually include a maximum power point tracker (MPPT) to track this varying power, in order to transfer all the available power to the grid efficiently. Control of power transferred to the grid along with the MPPT plays a crucial role in determining the efficiency of a PV system. This paper discusses about the basic power transfer theory between sources (PV and Grid) and focuses on the need of a DC-DC boost circuit, along …

Evidence Based Evaluation Research In Building Services Engineering, Kevin Kelly

Conference papers

This paper highlights the importance of research in the present volatile external environment in order to improve value to clients. It is focused at Building Services Engineers in Ireland.

Bs News March/April

Building Services Engineering

No abstract provided.

Predicting Neointimal Hyperplasia In Stented Arteries Using Time-Dependant Computational Fluid Dynamics: A Review, Jonathan Murphy, Fergal Boyle

Articles

This paper reviews the recent literature regarding the time-dependant computational fluid dynamics (CFD) analyses of blood flow through implanted coronary stents. The in vivo processes which result in arterial restenosis are identified. The definition and range of the computationally predicted variables which are believed to stimulate the restenosis processes are evaluated. The reviewed literature is subdivided into effect-based in which the effects of altering the flow model are investigated and design-based in which different geometric stent configurations are compared. Finally, conclusions are made regarding the body of work reviewed and recommendations are provided for future work in this field.

Tidal Energy Update 2009, Fergal O'Rourke, Fergal Boyle, Anthony Reynolds

Articles

Tidal energy has the potential to play a valuable part in a sustainable energy future. It is an extremely predictable energy source, depending only on the gravitational pull of the moon and the sun and the centrifugal forces created by the rotation of the earth-moon system. Tidal energy has been exploited on a significant scale since the construction of the La Rance tidal barrage in France in 1967. A tidal barrage utilises the potential energy of the tide and has proven to be very successful, despite opposition from environmental groups. Kinetic energy can also be harnessed from tidal currents to …

Fourier Transform Infrared Microspectroscopy And Multivariate Methods For Radiobiological Dosimetry, Aidan Meade, Colin Clarke, Hugh Byrne, Fiona Lyng

Articles

The scientific literature contains an ever-growing number of reports of applications of vibrational spectroscopy as a multivariate non-invasive tool for analysis of biological effects at the molecular level. Recently, Fourier transform infrared microspectroscopy (FTIRM) has been demonstrated to be sensitive to molecular events occurring in cells and tissue after exposure to ionizing radiation. In this work the application of FTIRM in the examination of dose-dependent molecular effects occurring in skin cells after exposure to ionizing radiation with the use of partial least-squares regression (PLSR) and generalized regression neural networks (GRNN) was studied. The methodology is shown to be sensitive to …

Miniature Ceramic Pifa For Uwb Band Group 3 And 6, David Kearney, Matthias John, Max Ammann

Articles

A ceramic chip planar inverted-F antenna (PIFA) is proposed for integration into a mobile handset providing UWB functionality across band groups 3 and 6. The antenna design exhibits a total efficiency of greater than 50% across the entire 6.39 GHz bandwidth while maintaining a very small volume of 57.6 mm^3 . The antenna uses a combination of the normal PIFA resonance and a second resonance due to the ceramic block to achieve a broad ultrawideband (UWB) bandwidth.

A Multi-Variable Analysis Of Transient Near-Wall Haemodynamics In A Stented Coronary Artery, Jonathan Murphy, Fergal Boyle

Conference Papers

No abstract provided.

Thermal Robotic Arm Controlled Spraying Via Robotic Arm And Vision System, Dermot Breen

Doctoral

The Tribology Surface Engineering industry is a worldwide multi billion euro industry with significant health and safety risks. The thermal spraying sector of this industry employs the technique of applying molten surface coating material to a substrate via a thermal spray process which is implemented either by manual spraying or pre-programmed robotic systems. The development of autonomous robotic systems for thermal spraying surface coating would significantly improve production and profitability over pre-programmed systems and improve health and safety over manual spraying. The aim of this research was to investigate and develop through software simulation, physical modelling and testing the development …

Towards An Integrated Approach To Engineering Ethics, Eddie Conlon

Conference papers

There is an increasing diversity in approaches to teaching engineering ethics due to increasing dissatisfaction with the dominant approach which uses case studies focused on moral dilemmas confronting individual engineers. There has been a demand for a greater consideration of the organisational and social context in which engineers work and for a shift in focus from micro ethics issues concerning individuals to macro issues of concern to the engineering profession. Further, there has been a demand that engineers focus on societal decision making about technology and their role in policy development. Drawing on the work of the American sociologist George …

The Use Of Novel Non-Destructive Methods For Quality Control And Performance Evaluation Of Concrete Structures, Sree Nanukuttan, Niall Holmes, Sudarsan Srininvasan, Lulu Basheer, Muhammed Basheer, John Mccarter, Gerry Starrs

Conference papers

Concrete cover provides the first line of defense against the ingress of many deleterious substances into the concrete. Therefore, a measure of its transport properties is vital in assessing its long term performance in a given exposure condition. In new structures the rate of ingress of the deleterious substances could be monitored using array of electrical sensors that are embedded in the cover concrete. For structures that are currently in service, tests can be performed by removing cores from the structure (lab based tests) or by using tests that can be performed on the surface (in situ tests). Results relating …

On The Use Of A Dynamic Hybrid Tempo Detection Model For Beat Tracking, Mikel Gainza

Conference papers

In this paper, an approach that estimates the times at which musical beats occur is presented. The system uses a hybrid multi-band decomposition in order to estimate the music tempo. Following this, beat events are tracked by using a dynamic programming approach, which is updated by using short time tempo estimates. The hybrid decomposition is used in order to calculate the tempo by using different onset detection functions in different frequency bands. In addition, a method that estimates which frequency bands provide reliable periodicities is also presented. The accuracy of the model is evaluated by comparing the presented system against …

The Size Ellect On The Infrared Spectra Of Condensed Media Under Conditions Of Id, 2d And 3d Dielectric Confinement, Igor I. Shaganov, Tatiana S. Perova, Vasily A. Melnikov, Kevin Berwick

Articles

A general expression for the dielectric loss spectrum of an absorbing composite medium was obtained from a Maxwell-Garnett general equation. This expression was simplified for the cases of one, two and three dimensional dielectric confinement in both ordered and disordered thin layers, rods (wires) and spheres of absorbing medium which are considered as mesoparticles or mesoscopic molecules. This theoretical approach was verified experimentally using high purity organic liquids with strong absorption bands in the infrared range. Three organic liquids, namely benzene, chloroform and carbon disulphide, were measured in various dielectric confinement configurations using Fourier Transform Infrared (FTIR) spectroscopy with a …

Double Quantum Dot Photoluminescence Mediated By Incoherent Reversible Energy Transport, S. Yu Kruchinin, A. V. Federov, A. V. Baranov, T. S. Perova, Kevin Berwick

Articles

We present a theoretical study of the stationary photoluminescence of two, direct-gap, semiconductor nanocrystals, taking into account electronic excitation energy-transfer processes due to electrostatic interaction. The results obtained here allow for the incoherent reversible energy transport that occurs when the intraband relaxation rate in a quantum dot acceptor is comparable to, or less than, the energy-transfer rate. We investigate the secondary emission of two different electronic level schemes that can be realized experimentally, obtain analytical expressions for the luminescence differential cross section, and perform an analysis of its spectrum. It is shown that when excitation is not in resonance with …

A Macrobending Singlemode Fiber Refractive Index Sensor For Low Refractive Index Liquids, Pengfei Wang, Yuliya Semenova, Yong Li, Qiang Wu, Gerald Farrell

Articles

An all-fiber refractive index sensor with a simple configuration is proposed and investigated. The proposed fiber refractometer consists of a full-loop structure of bare high-bend loss singlemode fiber-1060XP, employing the well-known whispering gallery mode (WGM) effect induced by the evanescent wave excitation to measure the refractive index of an external medium. A competitive sensitivity is achieved (average 725.76nm/RIU at a bend diameter of 19.3mm) compared with other fiber-optic sensors, plus benefits resulting from simplicity, low cost and ease of fabrication.

Study Of The Effect Of Source Signal Bandwidth On Ratiometric Wavelength Measurement, Qiang Wu, Yuliya Semenova, Ginu Rajan, Pengfei Wang, Gerald Farrell

Articles

We derive an analytic equation for a ratiometric wavelength measurement system and analyze the influence of the optical source signal bandwidth. Our investigation shows that in a particular optical sensing system, the higher the bandwidth of the optical signal, the better resolution the system will achieve. Experiments based on two types of optical signals (output signal of a tunable laser and a fiber Bragg grating) were carried out, and experimental results verified both the simulation results and the theoretical analysis.

The Effects Of Harmonics On Power Quality And Energy Efficiency, Alan Harrison

Other resources

By making our electricity supply more secure, reliable and versatile will mean that we reduce our reliance upon oil, gas and solid fuels, which mostly exist outside of Ireland and the European community. The majority of our fuel is imported and this makes our economy dependent on outside interests and out of our control. Even more importantly as the world’s fossil fuel reserves are running out and electricity demand is ever increasing.

If we make our electricity networks secure and designed to the highest standards we can import and export electrical energy more easily as our demands change, for example …

Social Enterprise: An Overlooked Approach To Promoting Sustainable Economic Regeneration, Gerard Doyle

Reports

Across Europe, social enterprises are making a significant impact on communities, particularly those blighted by high levels of unemployment, poverty and disadvantage. According to the European Commission, they represent 2 million enterprises (i.e. 10 per cent of all European businesses) and employ over 11 million paid employees (the equivalent of 6 per cent of the working population of the EU). Social enterprises are present in almost every sector of the economy, such as banking, insurance, agriculture, craft, various commercial services, and health and social services. The benefits of social enterprises are many, but in economic terms, they can support the …

Cloud Computing And Its Application In The Irish Construction Industry, Alan V. Hore, Roger West, Alan Redmond

Conference papers

The significance of Irish Small to Medium Size Enterprises (SMEs) being more effective and efficient with eBusiness solutions in the construction industry has never been more evident than in today’s global economy. Through the development of a strong and proactive network the Construction IT Alliance (CITA) hope to create a platform for implementing the use of eBusiness in the SME community. This network will provide SME companies with a direction on how to improve their efficiency and effectiveness through the use of technology. At present CITA has identified a potential business solution that would make construction software more accessible by …