Engineering Commons^™

Comparative Analysis Of Single And Double Dwell Acquisition Schemes, Gurinder Singh Ahluwalia

Theses

Single and double dwell pseudonoise (PN) acquisition systems are described, explained and analyzed. These systems are designed to synchronize a locally generated PN signal with a received PN signal of unknown phase in the presence of noise. The mean, variance and an approximate probability distribution function (PDF) of the acquisition time for the single and double dwell PN acquisition schemes is developed. Intuitively, the double dwell acquisition system should be superior to the single dwell system because of the ability to quickly dismiss incorrect cells and further verify probable hits. It is shown analytically that this is in fact true …

Improving The Throughput Of Plasticating Extruders : Measurement Of The Interparticulate Friction Coefficient For Polymeric Particulates With Circular And Profiled Cross Sections, Aiping Chen

Theses

This thesis deals with the coefficient of friction between individual polymeric pellets, the interparticulate friction coefficient (IPFC). It has been measured using a shear cell for a wide variety of circular and profiled cross?section pellets for a variery of polymeric materials. First, the thesis explains the reasons why it is desirable to enhance the IPFC based on the melting mechanisms in a single screw plasticating extruder. By making pellets with profiled cross?section pellets, the IPFC is greater than for pellets of circular cross?section. Second, it describes the test apparatus for measuring the IPFC and the method for calculating the IPFC. …

Point Pattern Matching By A Genetic Algroithm, Minghwang Chen

Theses

The problem we consider is to find a subset of points in a pattern that best match to a subset of points in another pattern through a transformation in a least squares sense. Exhaustive search to find the best assignment mapping one set of points to another set is, if the number of points that are to be matched is large, computationally expensive. We develop a genetic algorithm which searches for the best ("almost the best") assignment efficiently. To map the point pattern matching into the framework of a genetic algorithm, we use a fitness function which inversely proportional to …

Performance Evaluation Of Consumer Electronic Bus, Sairaj R. Pakkam

Theses

This thesis describes the performance evaluation of the Consumer Electronic Bus proposed by the Electronic Industries Association. To study the behaviour of CEBUS under different traffic conditions, a simulation program was developed modelling the layer architecture of CEBUS. The CEBUS is based on the ISO/OSI model of layered architecture. The simulation results have shown that, when the throughput of the network is small, the delay is bounded for all messages of all priorities. As the throughput of the network increases, under the presence of more high priority messages, the lower priority messages get queued at their nodes. It is also …

Hardware Algorithms For Computing Transcendental Functions, Xin-Pei Gong

Theses

The COordinate Rotation Digital Computer(CORDIC) is a special-purpose digital computer for real-time airborne computation. In this computer, a unique computing technique is employed which is especially suitable for solving the trigonometric relationships. A new computing technique based on the CORDIC algorithm is developed to reduce the number of iterations by one half for each input angle. This improvement is accomplished. by scanning multiple bits of the input angle(in our case, two) at a time. The CORDIC equations are rewritten accordingly and a hardware implementation structure is also presented. The results of the software simulation of the new algorithm are as …

A Critical Analysis On Cogeneration Policy, R. Tjahjokartiko Gondokusumo

Theses

It could be difficult to understand electricity problems without knowing its history; how a combine of legal, administration, and financial means effects electricity in the development. The recent public law on energy-related issues traceable by this study is the Renewable Energy and Energy Efficiency Technology Competitiveness Act of 1989.

In short, cogeneration was proposed to utility (as public property) from industry (as private property) under PURPA (of which National Energy Act is the legislative history). Thus, it should be clear that the problems of cogeneration is not pro or contra issues. It is a national issue. Then, a cogeneration planner …

Conditional Artificial Dielectric Waveguide, Hsien-Wen Ho

Theses

A thin layer of semiconductor ( the guest material ) is sandwiched between two polymeric films ( the host material ) to form an artificial dielectric waveguide. An artificial dielectric is a composite material consisting of a dielectric with a large number of conducting particles arranged in a three-dimensional pattern. The particle dimensions are smaller than the optical wavelength of interest. A beam of light with a photon energy above the band-gap of the semiconductor ( pump light ) induces electric and magnetic dipoles which affect the propagation of light with a photon energy below the band-gap ( probe light …

Small Disturbance Stability As Affected By Excitation Controls, Alfredo Flores

Theses

The effect of excitation control systems on the power system's small disturbance stability limits has been investigated in this thesis. Three excitation control schemes namely the proportional, fast?acting and the modified fast?acting have been studied.

The stability results were predicted directly in terms of the AVR gain controlling parameters following one?dimensional and two?dimensional frequency domain separation technique. The necessary algorithms and computer simulation programs have been developed.

In case of a modified fast?acting excitation control with three unknown variables, a procedure has been proposed to obtain the stability results by extending the two?dimensional frequency domain separation technique.

Effect Of Moisture On Microcircuit Failure, Chandrabala D. Patel

Theses

Stability and reliability of microcircuit is dependent on its design, fabrication, testing, storage and use.

In this thesis emphasis is given on various failure mechanisms of Integrated Circuits in humid environment and techniques of improving reliability. Other factors which affect the failure of integrated circuits are also discussed. Moisture induced failure modes, semi-reversible failures and irreversible failures (surface leakage current and corrosion-causing interruption of interconnection lines) are also reviewed.

Controlling the contaminants and moisture related corrosion are also covered. The quickest way to evaluate the reliability of microcircuit is by accelerated aging test and by selection of meaningful criteria of …

Damage Effects To Si-Sio2 Structures Due To Reactive Ion Etching, Moshe D. Bunyan

Theses

This thesis presents the damage effects to the Si ? SiO₂ structures due to Reactive Ion Etching (RIE). The research was carried out on Si ? SiO₂ MOS capacitors which were fabricated using RIE and wet etch (Hydrofluoric acid etch (HFE)) Process. The experiment was carried out using CV technique and Ellipsometry. Various electrical parameters were measured from CV *curves of these MOS capacitors. It was observed that the CV curve obtained for the RIE etched sample showed considerable deviation from that of the control sample. This indicates the presence of excess of interface trap charge density which …

Improving Solids Conveying In Plasticating Extruders : An Investigation Into Manufacturing Processes And Manufacturing Systems For Profiled Thermoplastic Pellets, Oommen Cherian

Theses

The objective of the thesis is the manufacture of thermoplastic bilobal and trilobal profiled pellets for the determination of the interparticulate co-efficient of friction exhibited by solid beds of such pellets. The enhancement of the interparticulate coefficient of friction is expected to lead to ameliorated solids conveying rates in plasticating extruders.

Predicting the product shape from a profile die is very difficult due to the elastic memory of plastics and the complex boundary conditions. Consequently the cost involved in experimenting with different profile dies is high. Therefore a standard die with several die inserts of varying cross-sections were used to …

Functional Requirements For Computer Conferencing And Computer Mediated Communications, Computerized Conferencing & Communications Center, Murray Turoff, Starr Roxanne Hiltz, James Whitescarver, John Foster

Computerized Conferencing and Communications Center Reports

This paper is a compilation of the desirable functionality for Computerized Conferencing Systems. It is based upon the research and evaluation activities of the Conferencing Center at NJIT and can he considered as an overall set of objectives for the development of its Conferencing Systems.

Computer Aided Localization Of Neurological Diseases, Yusuf Parlar

Dissertations

Computers in medicine has brought new dimensions and better understanding of uncertainties in the field of medical sciences in the last decade. This thesis is focused upon the localization of neurological lesions in the human nervous system. It relates clinical neurological test outcomes to pathways of function or malfunction. Certain methods are proposed-empirical. stochastic. Deterministic-to estimate the spatial distributions of lesion probabilities.

First. a Bayesian model is presented to estimate the posterior probability of lesion from a priori information, based on the test outcomes. Due to unavailable data alternative methods and models are presented: Regression Analysis. Monte Carlo simulation, and …

On The Performance Of Minimum Redundancy Array For Multisource Direction Finding, Byung-Seub Lee

Dissertations

As an application of power spectrum estimation, the multi-source direction finding has been evolved from conventional FFT method to Superresolution methods such as Multiple Signal Classification(MUSIC) algorithm. Uniform Regular Array(URA) was mainly used in all these approaches.

The Minimum Redundancy array(MRA); a non-uniform thinned array which results in an input signals covariance matrix with minimum redundancy has been shown to have certain interesting properties for spectrum estimation. Only recently it was suggested to use the MRA for spatial estimation. The purpose of this research was to study the performance of this array in multi-source direction finding estimation and compare it …

Computer Modeling And Analysis Of Biological Rhythms, Shi Xiong Yang

Dissertations

Biological rhythms are an important phenomenon and feature of physiologic systems. Indirect means have to be employed for their description and exploration due to the unclear internal nature of the system. This study analyzed and developed several possible mathematical models using single or multidimensional nonlinear differential equations to approach the experimental circadian data. The numerical solutions of the models were obtained by computer simulation and the simulated and experimental acquired circadian data were analyzed in both the time and frequency domains. Phase plane plots, phase response curves and power spectrum analysis were employed to determine the nonlinearity of the system …

Mass Transfer Of Hazardous Organic Compounds In Soil Matrices Relevant To Thermal Desorption/Incineration, Jong-In Dong

Dissertations

Soils contaminated with hazardous organic compounds have been known to threaten human health both directly through various contact mechanisms and indirectly through leaching or transfer to the food chain. Thermal desorption of contaminated soil matrices with secondary treatment of the effluent gases (collection, incineration, etc) is one of most feasible and developing technologies for cleaning of contaminated soils. There is, however, little known about the mass transfer principles of organic contaminants through the heated soil matrices. The objectives of this study is, therefore, to learn and understand details of the mass transfer processes of organic compounds in these soil matrices. …

A Comparative Study Of Edge Detection Techniques, Jaskaran Singh Dhaliwal

Theses

The problem of detecting edges in gray level digital images is considered. A literature survey of the existing methods is presented. Based on the survey, two methods that are well accepted by a majority of investigators are identified. The methods selected are: 1) Laplacian of Gaussian (LoG) operator, and 2) An optimal detector based on maxima in gradient magnitude of a Gaussian-smoothed image. The latter has been proposed by Canny[], and will be referred as Canny's method. The purpose of the thesis is to compare the performance of these popular methods. In order to increase the scope of such comparison, …

An Artificial Neural Network For Redundant Robot Inverse Kinematics Computation, Wibawa Utama

Theses

A redundant manipulator can be defined as a manipulator that has more degrees of freedom than necessary to determine the position and orientation of the end effector. Such a manipulator has dexterity, flexibility, and the ability to maneuver in presence of obstacles. One important and necessary step in utilizing a redundant robot is to relate the joint coordinates of the manipulator with the position and orientation of the end-effector. This specification is termed as the direct kinematics problem and can be written as x = f(q)
where x is a vector representing the position and orientation of the end-effector, q …

Design And Analysis Of Movable Boundary Allocation Protocol, Karun Sekhri

Theses

The increasing digital communications traffic will require very high speed networks. The use of high communication speed increases the ratio between end to end propagation delay and the packet transmission time. This increase causes rapid performance deterioration and restricts the utilization of the high system bandwidth in broadcast channel based systems. Using several parallel channels in place of a single channel improves this ratio. For a given system bandwidth the total system capacity is increased by bandwidth division and parallel communication. FTDMA protocols have been suggested for the parallel channel network and these protocols are suitable for different loads. In …

Statistical Process Control For High Precision Deep Drawn Sheet Metal Parts, Sunil S. Shah

Theses

In today's world, industrial expertise has come to be judged in terms of the quality of the product. Good quality has become the ultimate aim in a manufacturing environment, which leads to many innovations for ease in the inspection of parts. In considering a metal working company like Hudson Tool & Die Company, a study of the various operations and the application of Statistical Process Control to the forming operations is performed using STORM software. Important characteristics have been carefully studied with regards to metal forming like uniform metal thickness, radius of the bend, depth of the drawing operation. In-depth …

Control Of Stress In Silicon Nitride Thin Films, Ajay Krishnan

Theses

Silicon nitride thin films of varying composition and thickness were deposited on silicon substrates by reactive rf diode sputtering of a silicon target using an argon/nitrogen gas mixture. Film stoichiometry could be controlled by varying the partial pressure of nitrogen, the total sputtering gas pressure and the target rf power. Films with refractive index of 2.01, the value for stoichiometric silicon nitride, could be obtained. Film stress was measured by wafer curvature; refractive index and thickness of deposited films were obtained by ellipsometry and interferometry measurements. The etch rate in buffered HF for films with refractive index 2.05 was 29A/min; …

Construction Cost Estimating In Project Management, Kalpit N. Patel

Theses

The primary objective of Cost Estimating is to support the timely generation of bid or alternative estimates. Cost Estimating also supports management analysis of estimate accuracy, reasonableness and project risk through the generation of summary reports and analysis. Estimates also provide a base of information during construction for such items as scope changes to the contract, variations in costs of the project cost, total project cost, feedback for scheduling etc.

Contruction cost estimating is the process of identifying and compiling the many items of cost that will enter into a construction project. This is a procedure that requires very detailed …

Experimental Evaluation Of Process Zone Deformation In Concrete, Cherng-Maou Meng

Theses

Concrete structures are often subjected to a variety of loading conditions. Under ultimate load design, concrete structures can resist these loads without evident deformation. However, under service, tension cracks will develop and depending on their location, they may impair load carrying capacity.

It is generally believed that microcrack development is preceeded by formation of a relatively long microcracked region. A large number of studies have indicated that due to formation of this process zone (microcracked zone), Linear Elastic Fracture Mechanics (LEFM) principles are not applicable to concrete. However, a number of nonlinear models can be developed if the length of …

Configuring Maps For A Satellite Communication Network By Self- Organization, Yizhong Chen

Theses

There are several management tasks in a telecommunication network. Among which traffic management is one of the most important and difficult tasks. It is concerned with maximizing network efficiency when the network is under stress either due to overload or failure. New attempts to automate this task such as expert system based approach are yet to be perfected. In this thesis, we advocate a new concept of traffic management. Our scheme consists of two levels. At the first level, we introduce a Self-organization model to dynamically configure a map for a satellite communication network. The second level is a routing …

Prestressed Concrete Columns Under Bending And Axial Load, Ajit Chiplunkar

Theses

A general analysis and design equation for slender and nonslender prestressed concrete columns subjected to uniaxial or biaxial moments combined with axial load is proposed. The proposed equation is an extension to the one developed by Hsu for reinforced concrete columns. The analytical results of the ultimate loads of eccentrically loaded slender prestressed columns are compared with the experimental results reported by Brown and Hall and Aroni respectively. The comparative study shows that the proposed equation of interaction diagram is in good agreement with the actual tests.

The ultimate loads of biaxially loaded short columns are also compared with the …

Three Dimensional Finite Element Analysis Of A Tibial Ankle Prosthesis, Harrison Philip Crowell Iii

Theses

In this study, three dimensional finite element analysis is used to evaluate and compare partially and fully porous coated tibial components, of an ankle prosthesis, implanted in the distal tibia. The geometry of the distal tibia is determined from measurements of cross sections of a human tibia. From the measurements, solid models of the cancellous and cortical bone are created. A solid model of the tibial component is created and positioned in the solid model of the bone. From the solid model, a finite element model is created for the partially coated case and for the fully coated case. Each …

The Application Of Microwave Technology To The Remediation Of Non- Volatile Organic-Contaminated Soil, Huiping Gu

Theses

The application of microwave technology to the remediation of soils contaminated with non-volatile organic chemicals is the subject of this thesis. It had been previously shown in this laboratory that volatile and semi-volatile organics could be steam distilled from soil. This study has been focussed on the applicability of microwave treatment of soil contaminated with non-volatile organics at relatively low temperatures achievable by in situ microwave treatment. Non-volatile toxics, like dioxin, pose their greatest danger when excavated and transported, according to the EPA, therefore, there is an urgent need for an in situ remediation process. Microwave treatment is one of …

Non-Parametric Dominant Point Detection Algorithms, Kuo-Wei Huang

Theses

Dominant point detection is one of the most important preprocessing steps for landmark-based shape recognition and point-based motion estimation. Two new methods for detecting dominant points are presented. Both methods do not require any input parameter and the dominant points obtained by these methods remain relatively the same even when the object curve is scaled or rotated.

In the first method, for each boundary point, a support region is assigned to the point based on its local properties. Each point is then smoothed by a Gaussian filter with a width proportional to its determined support region. A significance measure for …

Adhesion Effects In Micro Mechanisms, Dennis Alan Kalgren

Theses

Dielectric resonators (DR) are suitably shaped objects made of high dielectric constant materials like TiO2, BaO, ZnO, and accessory ingredients, which can function as electrical resonators covering a very wide frequency range upto 40GHz. The physical dimensions of dielectric resonators are in mm range. High dielectric constant material resonators seem to be ideally suited for microwave applications because of their miniature size, low loss, insensitivity to magnetic dc biasing fields, and ability to concentrate large RF magnetic fields in small volumes. However temperature stabilization of dielectric resonators is an important consideration as the center frequency is a function of temperature. …

An Mcs Basic-52 Sbc Using Anything But An 8052ah-Basic, Hyunyeop Lee

Theses

This thesis exploits the ways to develop a new MCS BASIC-52 SBC using anything but an 8052AH-BASIC microcontroller. The 8052AH-BASIC based SBC offers short development time and low system cost; it is advantageous for numerous applications especially in the instrumentation, measurement and process control. However, the 8052AH-BASIC is no longer officially supported by INTEL and could disappear. Also, this SBC is not adequate for applications where power consumption is an important factor because the 8052AH-BASIC, a MOS product, draws a considerable amount of current.

To solve these problems we demonstrate how the 8052AH-BASIC can be replaced by any of a …