Engineering Commons^™

Prediction Of Deflection Of Helical Anchors Under Load, Andre Stephen Hawks

Doctoral Dissertations

”As the sophistication of modern structural design methods has improved over time, the ability to accurately predict and model foundation stiffness has become increasingly more important. In complicated structural systems with deep foundations, correct calculation of the distribution of load and serviceability requires proper modeling of axial load-deflection characteristics. To keep pace with advances in structural analysis, there is much need for more practical and scientific work on the load-deflection prediction of deep foundations including Helical Anchors.

The load-settlement mechanism of an axially loaded helical pile is a complex soil-structure interaction problem influenced by helical pile dimensions, installation method, and …

Thermal And Mechanical Properties Of Novel Carbide Materials, Evan Charles Schwind

Doctoral Dissertations

"This research focuses on studying the thermal and mechanical properties of novel carbide materials at room and elevated temperatures. The novel carbide materials investigated include zeta phase tantalum carbide (ζ-Ta₄C_3-x) and a high entropy (Ta,Hf,Nb,Zr)C carbide. The electrical resistivity and thermal conductivity of zeta phase tantalum carbide (~96 wt.%) were measured as 160 ± 4.2 μΩ-cm and 9.6 W/m•K. These are higher and lower (respectively) than for cubic tantalum carbide, most likely due to planes of carbon vacancies present in the ζ-Ta₄C_3-x crystal structure. The thermal conductivity of (Ta,Hf,Nb,Zr)C was lower than any …

Assessment Of Rib Failure Mechanisms Using Discontinuum Mechanics Based Modeling Approach, Maurice Nuonituo Sunkpal

Doctoral Dissertations

"Coal mine rib failures are major safety and health challenge for coal mines worldwide. The need for clear procedures to evaluate mine rib behavior and to provide an efficient, reliable, and consistent rib control protocol is needed. Understanding coal rib geomechanics is essential for improving rib stability and eliminating fatality and injury trends due to rib failures. This knowledge is also vital to determine support requirements.

The rib control practices used in the 21st Century in most countries originated in roof control techniques. Understandably, applying roof control methods to coal rib does not yield desirable results. The geology of structures …

Computational Intelligent Impact Force Modeling And Monitoring In Hislo Conditions For Maximizing Surface Mining Efficiency, Safety, And Health, Danish Ali

Doctoral Dissertations

"Shovel-truck systems are the most widely employed excavation and material handling systems for surface mining operations. During this process, a high-impact shovel loading operation (HISLO) produces large forces that cause extreme whole body vibrations (WBV) that can severely affect the safety and health of haul truck operators. Previously developed solutions have failed to produce satisfactory results as the vibrations at the truck operator seat still exceed the “Extremely Uncomfortable Limits”. This study was a novel effort in developing deep learning-based solution to the HISLO problem.

This research study developed a rigorous mathematical model and a 3D virtual simulation model to …

Investigating The Effect Of Operating Condition On Esd-Induced Soft-Failures, Omid Hoseini Izadi

Doctoral Dissertations

"Conflicting observations have been found in the literature regarding the effect of operating conditions on ESD (electrostatic discharge) susceptibility. While some studies have suggested a strong correlation between the two, others observed little to no correlation. In this work, a systematic study has been carried out suggesting the existence of a strong correlation between the ESD susceptibility and operating conditions. It is found that the root cause of this conflict is random ESD noise injection. A measurement approach is proposed to synchronize the noise injection with the system activity such as high/low CPU load. In this approach, the current consumption …

Exposure Assessment Of Emerging Contaminants: Rapid Screening And Modeling Of Plant Uptake, Majid Bagheri

Doctoral Dissertations

"With the advent of new chemicals and their increasing uses in every aspect of our life, considerable number of emerging contaminants are introduced to environment yearly. Emerging contaminants in forms of pharmaceuticals, detergents, biosolids, and reclaimed wastewater can cross plant roots and translocate to various parts of the plants. Long-term human exposure to emerging contaminants through food consumption is assumed to be a pathway of interest. Thus, uptake and translocation of emerging contaminants in plants are important for the assessment of health risks associated with human exposure to emerging contaminants. To have a better understanding over fate of emerging contaminants …

Fiber Reinforced Polymer Bar Investigation: Long-Term In-Situ Durability And Bond Strength Assessment In Conventional And Sustainable Concrete, Ali Fadhil Al-Khafaji

Doctoral Dissertations

"Corrosion of steel reinforcement and carbon dioxide emissions are two major global problems. Different methods, techniques, and materials have been implemented to mitigate these problems. Glass fiber-reinforced polymer (GFRP) bar presents itself as a solid alternative to replace conventional steel reinforcement owing to its fantastic features in resisting corrosion. Its demand is progressively increasing. Cement-based concrete, on the other hand, is not eco-friendly due to the excessive amount of carbon dioxide (CO₂) emissions yielded from its cement production. One of the alternatives used to mitigate the use of cement in concrete is fly ash. Fly ash is considered …

Evaluation Of Excavated Surface Irregularities And Hardness Of Mechanical Excavations And Their Relationship With Excavator Performance, Prosper Evaristus Akansah Ayawah

Doctoral Dissertations

"This research involved lab and numerical excavation of a clastic sedimentary rock (Roubidoux Sandstone) using a long-bladed disc cutter in a Linear Rock Cutting Machine (LCM) with the aim of establishing relationships between the cutting parameters, excavated surface parameters (underbreaks, overbreaks and hardness), and performance parameters (specific energy and cutting rate). Three-dimensional cutting forces were recorded during the linear cutting. A structured laser imaging system was used to image the excavated surfaces for the estimation of the irregularities (ridge volumes (RV) and overbreak volumes (OV)). The excavated surface hardness was measured using the N-type Schmidt hammer. The numerical simulation was …

Fabrication, Characterization Of High-Entropy Alloys And Deep Learning-Based Inspection In Metal Additive Manufacturing, Wenyuan Cui

Doctoral Dissertations

"Alloying has been used to confer desirable properties to materials. It typically involves the addition of small amounts of secondary elements to a primary element. In the past decade, however, a new alloying strategy that involves the combination of multiple principal elements in high concentrations to create new materials called high- entropy alloys (HEAs) has been in vogue. In the first part, the investigation focused on the fabrication process and property assessment of the additive manufactured HEA to broaden its engineering applications. Additive manufacturing (AM) is based on manufacturing philosophy through the layer-by-layer method and accomplish the near net-shaped components …

Thermophysical Properties Of Nominally Phase Pure Boride Ceramics, Austin D. Stanfield

Doctoral Dissertations

"This research focusses on the thermophysical properties of nominally phase pure boride ceramics. As interest in ultra high temperature ceramics increases due to a renewed interest in hypersonic flight vehicles and with the expanding materials design space accompanying interest in high entropy materials, it is imperative to understand the intrinsic properties of boride ceramics. By reducing Hf content in ZrB₂ from the natural abundance, ~1.75 at% in this case, to ~100 ppm, thermal conductivity increased from 88 W/m·K to 141 W/m·K. Removal of Hf allowed the thermal conductivity of ZrB₂ with small transition metal solute additions to be …

Integrated Solar And Ess Ac/Dc Systems For Various Grid Applications, Phani Ratna Vanamali Marthi

Doctoral Dissertations

"Modular multilevel converters (MMC) have gained prominence for high power applications in recent years due to their technical merits such as voltage scalability, harmonic performance, and high efficiency. Integration of renewable energy sources such as solar photovoltaic (PV) systems and energy storage systems (ESS) to the grid using power electronic (PE) resources is increasing due to the techno-economic successes achieved by such systems. Following these developments, the integration of MMCs with PV plants and ESS systems is one of the dynamic research avenues being pursued. Along these lines, an integrated development of PV plants, ESS, and alternating- and direct-current (ac/dc) …

Theoretical Study Of Magnetic Particles In A Shear Flow Subjected To A Uniform Magnetic Field, Christopher A. Sobecki

Doctoral Dissertations

"Magnetic manipulation of non-spherical magnetic microparticles is important for applications in shape-based and magnetic-based separations such as waste management, disease diagnostics, drug delivery, and mining. Manipulations of magnetic microparticles also include chain formation to assemble compositions for electronics, drug loading designs, and magnetorheological fluids for smart armor, hydraulic brakes, and dampers. In microfluidic devices, separation-formation-effectiveness depends on the shape of the channel, the shear rate, and the magnetic field strength and direction.

Particle separation and chain formation involved highly complex and computational expense-demanding studies in microfluidic devices, magnetic fields, and particle- particle/wall interactions. This research took complex experimental studies and …

Stability Analysis Of Microgrids Using Markov Jump Linear Systems, Gilles Mpembele

Doctoral Dissertations

"This research discusses stochastic models for a microgrid operating between standalone and grid-tied modes. The transitions between different modes are modeled as a continuous-time Markov chain (CTMC). In each operating mode, the system is modeled using conventional differential algebraic equations (DAEs), linearized around some equilibrium point.

In Topic-I, a model is developed using the Stochastic Hybrid Systems (SHSs) formulation. The microgrid is modeled as a Markov jump linear system (MJLS), which is a type of SHS in which the discrete events evolve according to a Continuous Time Markov Chain (CTMC). The model allows for the derivation of Ordinary Differential Equations …

Fiber Optic Sensors For Industry And Military Applications, Yiyang Zhuang

Doctoral Dissertations

"Fiber optic sensors (FOSs) have been widely used for measuring various physical and chemical measurands owing to their unique advantages over traditional sensors such as small size, high resolution, distributed sensing capabilities, and immunity to electromagnetic interference. This dissertation focuses on the development of robust FOSs with ultrahigh sensitivity and their applications in industry and military areas.

Firstly, novel fiber-optic extrinsic Fabry-Perot interferometer (EFPI) inclinometers for one- and two-dimensional tilt measurements with 20 nrad resolution were demonstrated. Compared to in-line fiber optic inclinometers, an extrinsic sensing motif was used in our prototype inclinometer. The variations in tilt angle of the …

Agent-Based Model Of Broadband Adoption In Unserved And Underserved Areas, Ankit Agarwal

Masters Theses

"In the last two decades, demand for broadband internet has far outpaced its availability. The Federal Communications Commission’s (FCC) 2020 Broadband Deployment report suggests that at least 22 million Americans living in rural areas lack access to broadband internet. With the COVID-19 pandemic affecting normal life, there is an overwhelming need to enable unserved and underserved communities to adapt to the “new normal”. To address this challenge, federal and state agencies are funding internet service providers (ISPs) to deploy infrastructure in rural communities. However, policymakers and ISPs need open-source tools to predict take-rates of broadband service and formulate effective strategies …

Investigation Of Post-Acid Stimulation Impacts On Well Performance Using Fracture Modeling And Reservoir Simulation In A Jurassic Carbonate Reservoir, Muaath Alansari

Masters Theses

"Well stimulation (well fracturing) became an essential tool in the Oil and Gas industry to unlock the potential of unconventional reservoirs all over the world and especially in the Middle East. In Kuwait, well stimulation is obligatory when dealing with deep Jurassic carbonate reservoirs. Thus, the well fracture designing process plays a very critical role in determining the success of the stimulation job and the improvement of the recovery.

Several wells stimulated with 20% HCL have shown wide variations in both short and long term well production performance. The research aims to investigate and identify the possible reasons causing these …

Power Generation From Waste Heat During Oil Production, Subrahmanya Chandra Bhamidipati

Masters Theses

"The increase in the world population is causing a significant increase in the global demand for energy. This rise in demand is generally met with the use of fossil fuels. But there is considerable pressure to lessen the release of carbon through the combustion of fossil fuels. One way that the oil and gas industry can provide increased energy without carbon combustion is by extracting the latent heat energy contained in produced oil, gas and water from producing reservoirs, and from water which is cycled through depleted, end-of-life or abandoned reservoirs. Extracting this energy and using it to provide direct …

Mechanical Activation And Cation Site Disorder Of Spinel-Based Ceramics, Cole A. Corlett

Masters Theses

"This research focuses on the processing and the effects that has on the cation disorder of magnesium-aluminate spinel based (MgAl₂O₄) ceramics. The first goal of this project was to determine the effects of high-energy milling, i.e., mechanical activation, on cation disorder (inversion) within the spinel structure. First, 1:1 molar ratios of MgO:Al₂O₃ ceramics were processed using two green processing methods, ball milling (XD) and SPEX milling (mechanical activation, MA) followed by a subsequent annealing treatment in air to form a single spinel phase in each powder sample. Neutron diffraction analysis was employed to …

The Field Coupling Mechanism Study For Near Field Probe, Shun Liu

Masters Theses

"In this part, the radius of the loop is used to predict the voltage induced by the E- field in the circular loop antenna. The thin rectangle loop and thick rectangle loop have been investigated. The equivalent radius of the rectangle loop is estimated by the average of the one over the distance between the points on the loop to the center of the loop. The estimation matches with the numerical simulation"--Abstract, page iv.

Toward Understanding Commercial Additives For Zincate Electrogalvanizing, Margaret Scott

Masters Theses

"Cyanide zinc electrogalvanizing has been used for many years to produce high quality and uniform zinc coatings. Due to toxicity concerns, a significant amount of research has occurred to remove the use of cyanide while still producing a similar deposit. One of the resulting plating chemistries is the alkaline zincate bath.

Alkaline zincate plating has the advantages of low startup cost, low toxicity, and low corrosion rate. Despite these advantages, alkaline bath conditions do not produce acceptable zinc deposits without the use of plating additives, which can promote lustrous, smooth deposits. This research aims to: (1) generate fundamental electrochemical data …

The Role Of Psychological Reactance In Smart Home Energy Management Systems, Matthew Thomas Heatherly

Masters Theses

“With an ever-growing demand for energy, our increasing consumption is producing more greenhouse gases and other pollutants, impacting climate change. One approach to reducing residential energy consumption is through the use of smart energy management systems. However, automation from smart technology inherently removes a certain amount of control from the user. If loss of control is perceived as a loss of freedom, this may lead users to experience psychological reactance when using these products. A set of experiments was conducted to assess how three features of a message notification from smart home energy management systems may induce reactance in users. …

Development Of Complex Lattice Cell In Benchmark Model Of Particle Bed Critical System, Elijah Chamberlain Lutz

Masters Theses

“Criticality safety benchmark evaluations require the creation of models that most accurately represent the experiment being evaluated. In some cases this can be relatively trivial with experiments containing rather simple or standard geometry. In others, such as packed bed systems, this becomes unique and a more difficult process. The importance of accurate modeling of packed bed systems for the use of criticality safety benchmark evaluations was looked at. Four models were created of various complexities and accuracy. First the multi-particle bed, consisting of a fuel particle (UC_1.7 kernel with C shell) and two filler particles (Zircaloy-4 and C + …

Investigation Of The Sensitivity Of Human Arm To Small Interaction Forces During Physical Human-Robot Interaction (Phri), Fazlur Rashid

Masters Theses

“Understanding the human motor control strategy during physical interaction tasks is crucial for developing future robots for physical human-robot interaction (pHRI). Effective pHRI depends on humans communicating their intentions for movement with robots. In physical human-human interaction (pHHI), small interaction forces are known to convey their intent between the partners. It is speculated that small interaction forces contain significant information to convey the movement intention of pHHI. However, the mechanism underlying this interaction strategy is largely unknown. Hence, the aim of this work was to investigate what affects humans’ sensitivity to the interaction forces. The hypothesis was that small interaction …

A Compact Wavelength Meter Using A Multimode Fiber, Ogbole Collins Inalegwu

Masters Theses

“Wavelength meters are very important for precision measurements of both pulses and continuous-wave optical sources. Conventional wavelength meters employ gratings, prisms, interferometers, and other wavelength-sensitive materials in their design. Here, we report a simple and compact wavelength meter based on a section of multimode fiber and a camera. The concept is to correlate the multimodal interference pattern (i.e., speckle pattern) at the end-face of a multimode fiber with the wavelength of the input lightsource. Through a series of experiments, specklegrams from the end face of a multimode fiber as captured by a charge-coupled device (CCD) camera were recorded; the images …

Research And Development Of A Laser Hot Wire Deposition Process, Christopher Croft

Masters Theses

“Laser hot wire directed energy deposition (DED) is an increasingly popular method for improving deposition rates and overall reduction of build times in DED processing. While there is clear benefit, it is important to fully understand the impact of preheating the wire. This work focuses on developing a model that describes bead geometry output using all factors including the wire preheat. The model was fit with over 150 data points that explored a large range of each factor. The resulting model was then leveraged to evaluate a process control variable. The technique chosen used feedback from the hot wire system …

Analysis And Design Of Dc-Link Capacitor In Cascaded H-Bridge Multilevel Active Front-End Converter, Muhammad Shehroz Malik

Masters Theses

Medium-voltage grid-tied systems often use a cascaded H-bridge multi-level active front-end. In this converter, dc link bus capacitors play an important role in stabilizing the converter and enabling both active and reactive power injections. The present work provides analytical expressions for the capacitor current, which are essential for optimizing system design (especially capacitor size vs. lifetime). Then, the expression is incorporated into the grid connected bidirectional power system model. Consequently, this work contributes to the guiding principles to choose accurate dc link capacitor ratings against grid-side power delivery requirements.

DC-link capacitors come with an expiration date which is dependent on …

Numerical Behavior Of Steel H-Plies Repaired Using Layered Concrete Jacket, Fareh Waleed Abudawaba

Masters Theses

“This study developed finite element models (FEMs), using LS-Dyna software, to investigate the repair of corroded steel H-piles using concrete jacket. The concrete modeled as a layered material simulating 3D printed concrete. 3DPC is a new technology that can be used to repair or build structures without formwork by depositing concrete mixture layer by layer. For the 3DPC, this study investigated the feasibility of using alkali-activated concrete (AAC) synthesized using class C fly ash as the main binder. The fresh properties, extrudability, and buildability of the proposed concrete were investigated through open time and deformation tests, respectively. Hardened properties were …

Neural Network Supervised And Reinforcement Learning For Neurological, Diagnostic, And Modeling Problems, Donald Wunsch Iii

Masters Theses

“As the medical world becomes increasingly intertwined with the tech sphere, machine learning on medical datasets and mathematical models becomes an attractive application. This research looks at the predictive capabilities of neural networks and other machine learning algorithms, and assesses the validity of several feature selection strategies to reduce the negative effects of high dataset dimensionality. Our results indicate that several feature selection methods can maintain high validation and test accuracy on classification tasks, with neural networks performing best, for both single class and multi-class classification applications. This research also evaluates a proof-of-concept application of a deep-Q-learning network (DQN) to …

Axial Performance Of Self-Consolidating Concrete-Filled Fiber Tubes, Joshua David Carter

Masters Theses

"Concrete filled fiber tubes can be used to increase ductility and strength of a concrete member and self-consolidating concrete is an ideal material to use in practical applications of concrete-filled fiber tubular columns. However, the propensity of self-consolidating concrete to autogenous shrinkage could reduce the effectiveness of the concrete confinement. This research investigates the use of self-consolidating concrete in pre-cast FRP tubes and various methods of shrinkage reduction and compensation to increase the axial performance of said self-consolidating concrete-filled fiber tubes. Axial compression tests were performed under monotonic and cyclic conditions to determine the stress-strain relationship of the self-consolidating concrete …

Simulation And Modeling Of Hypersonic Turbulent Boundary Layers Subject To Adverse Pressure Gradients Due To Concave Streamline Curvature, Gary L. Nicholson, Junji Huang, Lian Duan, Meelan M. Choudhari

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Direct numerical simulations (DNS) of adverse-pressure-gradient turbulent boundary layers over a planar concave wall are presented for a nominal freestream Mach number of 5, with the objective of assessing the limitations of the currently available Reynolds-averaged Navier-Stokes (RANS) models. The wall geometry and flow conditions of the DNS are representative of the experimental data for a Mach 4.9 turbulent boundary layer that was tested on a two-dimensional planar concave wall model in the high-speed blow-down wind tunnel located at the National Aerothermochemistry Laboratory at Texas A&M University (TAMU). The DNS was validated against the experimental results of TAMU for the …