Engineering Commons^™

A Comprehensive Traffic Survey Of Phelps County, Missouri, Clifford D. Muir

Masters Theses

"The purpose of this study is two fold. The first of these purposes is to serve as a pattern or guide for any county or township wishing to conduct a comprehensive traffic survey. The second purpose of this study is to provide traffic classification and other data on a typical county system of rural roads. Today, many counties in the United States are faced with the problem of inadequate roads, due to the modernization of the American farm. While they realize this problem exists, may county governments have developed no organized method of studying and determining their needs...When the author …

A Study Of Missouri Flint Clay, Edmond Preston Hyatt

Masters Theses

"The problem is one of attempting to explain the peculiar nature of Missouri Flint Clay and to expand the knowledge concerning it. Among the questions for which answers are sought are: What makes Missouri Flint Clay so hard? What happens to Missouri Flint Clay when it is ground? What is the mineralogical constitution of Missouri Flint clay?"--Introduction, The Problem, page 1.

Temperature Fluctuations Within A Solid Of Finite Thickness, William Sanford Hogan

Masters Theses

"The object of this thesis is to determine by analytical methods the temperatures within a homogeneous plate of finite thickness subjected to a constant temperature on one side and a periodically fluctuating temperature on the opposite side. The heat flow in the other two directions is considered negligible in this problem. Periodic changes of temperature are frequent in nature and in engineering. The surface of the earth is heated periodically by the sun in its daily and annual cycle and the periodic temperature changes below the surface and the question to which depth these changes are appreciable were dealt with …

The Effect Of Calcium Chloride On Air-Entrained Concrete, Gerard Francis Hofstaedter

Masters Theses

"The essence of the problem is not fully set forth in the title in that all aspects are not covered. In this case, the term "effect" means how the compressive strength and the modulus of elasticity vary with the addition of calcium chloride...Many pages will be found concerning the relative merits of plain concrete versus air-entrained concrete. All phases of the problem have been covered thoroughly. Investigations have been conducted on both plain and air-entrained concrete to determine the compressive strength, flexural strength, durability and workability"--Introduction, page 1.

Separation Of Copper And Zinc On Synthetic Resins, Ernest Joseph Breton

Masters Theses

"It was desired to know whether ion exchange resins could be of value to the metallurgist in the recovery and separation of metals. The recovery and separation of copper and zinc from dilute solutions on Amberlite IRC-50, a carboxylic resin, and Amberlite IR-120, a nuclear sulfonic resin, were investigated. It was found that Amberlite IRC-50 could effectively remove copper ions from a solution of copper and zinc. Amberlite IR-120, due to the strong sulfonic acid groups, exhibited only a slight preference for copper as compared to zinc. It would seem that a judicious choice of resins coupled with appropriate chemistry …

Thermal Recovery Of Petroleum By Electrical Heating, Harold Roy Coffer

Masters Theses

"It is the purpose of this investigation to study the feasibility of recovering oil from laboratory size cores by passing electric current through the formation. If a voltage of sufficient magnitude could be applied to the formation to cause a flow of current, the formation would be heated. This heat should stimulate the flow of oil. The expansion of any gas present in the core together with the formation of hydrocarbon vapors should provide sufficient expulsive force to drive oil from the core. The effect of power expenditure, the necessary voltages, the changes of conductivity and power factor of the …

Rockbursts, Christian Maurice Colson

Masters Theses

"This paper does not pretend to originality; it is an attempt to bring to light the causes and the mechanism of rockbursts, as exposed in the literature. Furthermore, an endeavor has been made to give a comprehensive picture of the prediction, prevention, and control methods of rockbursts. Briefly, what has been done in the field of rockbursts, and what remains open to investigation is submitted to the reader. The choice of rockbursts as a thesis subject appears to be justified by the geologic interest of the question. Detailed geologic observations, and particularly the recording of all the structural features which …

A High-Temperature X-Ray Diffraction Camera And Its Application To Copper And Titanium, Robert R. Penman

Masters Theses

"The purpose of this research was threefold, and consists of the following sections: 1. Effective use of a high temperature x-ray camera, capable of reaching temperatures of 1000 ºC. 2. Investigation of the thermal dilation of certain cubic metals. 3. Accurate determination of the lattice constant (aₒ) of Beta Titanium at 900 ºC "--Introduction, page 1.

Torque-Stress Relations In Bolts With National Fine Threads, Eugene Casper Chase

Masters Theses

"Stresses, in bolts, caused by initial tightening have long been a problem to machine designers. To take care of these unknown stresses, produced by initial tightening, designers have used empirical formulas. These formulas originally used for National Coarse Threads, have been carried over into the field of National Fine Threaded bolts. No known tests have been conducted to determine whether or not these formulas hold in the initial tightening of Fine Threaded bolts. Initial tightening stresses may be caused by one of two ways. First, consider two flat ground plates to be held together by bolts to form a steam …

Solid Solution In The Series Sodium Tungsten Bronze, Lithium Tungsten Bronze And Tungstic Oxide, Godrej F. Doctor

Masters Theses

"The tungsten bronzes are a series of anionic substitutional solid solutions of alkali metal metatungstates and tungstic oxide. They are neither alloys nor intermetallic compounds, the term tungsten bronzes was adopted because of their remarkable metallic properties, e.g. luster, specific gravity and especially high electrical conductivity, which resembles to that of graphite. Due to its chemical inactivity and beautiful shades of color, it is used as a coating, especially in the plastic industry and for other ornamental products. The properties and the structure of these bronzes have not been investigated entirely satisfactory; within the last twenty years, only a few …

Effects Of Wave Action Upon The Design Of The Breakwater For Istanbul Harbor, Melih Suat Durusan

Masters Theses

"The city of Istanbul is situated on the southern entrance of the Bosphorus which separates Asia from Europe; at the same time it is the only strait that leads to the Black Sea. Istanbul is the city that connects Europe-Asia highways and railways. These features show that Istanbul is a very important port. The Golden Horn and the southern end of the Bosphorus constitute a natural harbor which has been in use for many years. Although the natural harbor has served its purpose in the past, the present conditions necessitate the presence of a new harbor...One economical method of improving …

Separation Of Cobalt From Zinc Sulfate Solutions By Synthetic Cation Exchange Resins, Wen-Hsiang Chang

Masters Theses

"The purpose of the present research is primarily to investigate the possibility of the separation and recovery of cobalt from zinc sulfate solutions by means of cation exchange resins. It is thought that such an investigation, seemingly of academic interest, might throw some light on determining the possibility of processing some industrial solutions containing both cobalt and zinc. Cobalt, for instance, has been well known as one of the most detrimental impurities in zinc electrolytic solutions. In spite of various purification treatments, small amounts of cobalt are often present in the electrolytic solution, causing a reduction in current efficiency and …

A Survey To Determine The Most Economic Design For Concrete Runways Of A Class 4 Airport, Yani Triandafilidis

Masters Theses

"This study is for the purpose of determining the most economical design for the runways of the Yesilkoy airport in Istanbul, Turkey. The discussion will include different design methods for the runways and the longitudinal and transverse joints that will be used in each case to provide crack control in the runway surfacing.

The city of Istanbul has a population of about one million. It is a growing city, being the industrial center of Turkey, and it also serves as a terminal for transcontinental airway systems. For these reasons it was decided to construct a class 4 airport for the …

The Potassium Tungsten Bronzes, Ching Hou Ma

Masters Theses

"The tungsten bronzes are a series of substitutional solid solutions of alkali or alkaline earth metatungstates and tungstic oxides. They are not really metallic alloys or intermetallic compounds but they possess some marked metallic properties such as metallic luster, good electric conductivity, high specific gravity, etc. For this reason the name of "bronzes" is applied to them"--Introduction, page 1.

Calibration Of Weirs By Means Of Critical Flow And Specific Energy, Robert A. Rapp

Masters Theses

"For many years man has been relying more each day upon metering devices to measure the flow of fluids in industry. The orifice, orifice meter, venturi meter, pitot tube, nozzle, flume and the weir have been employed, each having its own particular advantage.

In this parade of metering progress, the contracted weir has long been the forgotten brother of the suppressed weir. In almost every textbook on hydraulics or fluid mechanics, the following words appear, "end contractions are to be avoided where the weir cannot be calibrated". This skepticism and the length or absurdity of some contracted weir formulas led …

The Effect Of Pressure Prehydration On The Strength Of Hydraulic Cement Concrete, Thomas Holmes Whitfield Jr.

Masters Theses

"It appears that the rapidity of curing and the degree or ultimate strength of concrete can be influenced by both chemical and physical factors. The main function of the physical factors involved seems to be the creating of a more intimate combination of the cement and water which are the active ingredients. For example, finer grinding of the cement would present more surface area to the water; the application of heat would decrease the amount of surface tension of the water, in addition to speeding the chemical reaction, steam under pressure would force water into the porous particles of cement; …

Effects Of Higher Speed Explosives In Drift Rounds, Harve Preston Nelson

Masters Theses

"There is much still to be learned of what takes place in the actual explosive zone of a rock blast. Many factors, both known and unknown, have individual and collective effects. A program is now in progress by the Mining Department of Missouri School of Mines and Metallurgy for developing and preserving information about some of the factors affecting the use of explosives. Some work has been done. More is now being completed by Messrs. R. J. Jones and J. B. H. Fitz-William. Present plans call for continuing the research and gathering data on this subject which is so important …

Investigation Of The Effect Of Absorption Tower Size Upon Overall Mass Transfer Coefficients, James Robert Murrell

Masters Theses

"The purpose of this research project was to obtain data and determine whether or not a correlation exists between tower size and the overall mass transfer coefficient for a packed tower. A constant ratio of tower diameter to packing diameter of twelve to one was maintained. Three absorption towers were used; a twelve inch diameter iron tower, a six inch diameter iron tower, and a three inch diameter glass tower. One inch, one-half inch, and one-fourth inch Raschig rings were used in the corresponding towers as packing. The system used was the absorption of acetone by water from an acetone-air …

The Transformation Of The Aluminum-Zinc Eutectoid Alloy At Subcritical Temperatures, Thomas Joseph Burke

Masters Theses

"Interest in the mechanism of the austenite eutectoid transformation in iron-carbon alloys, especially as produced by the isothermal sub-critical techniques introduced by Davenport and Bain, has resulted in the application of similar heat treatment studies to the eutectoid transformations in other alloy systems. The study of the eutectoid transformation is of both fundamental and industrial interest because past experience has shown that these studies yielded much information concerning the nature and mechanism of the changes in eutectoid alloys during the decomposition of the phase stable at high temperatures and has also contributed much toward the development of new properties to …

Safety And Health In Mining, John Philip Lacke

Masters Theses

"The mining industry has long been criticised severely because of its high rate of accident occurrence. Statistics, which, however, are not strictly comparable show that the accident-frequency rate in all mining is currently about three times and the accident severity rate is about seven times as great as the average for general industrial work in the United States. Figures such as these are by no means comforting to mining men. They constitute a challenge to the industry that cannot be ignored.

It must be remembered that any type of mining is more hazardous than most or the other major occupations. …

The Development Of Plans For A National Airport For Ankara, Turkey, Mehmet Ragip Samli

Masters Theses

"'The present rapid development of general interest in aviation has brought to the front a new field of engineering. Development of the airplane has already reached a stage where the limit of its usefulness seems fixed only by the places which may be provided for taking off and landing. Due to the newness of the problem, not every one on whom responsibility rests recognizes the fact that the selection of the proper site and location for an airport is just as much an engineering problem as are its design and construction.'

The Turkish government began construction or the Ankara-Esenboga airport …

Construction And Operation Of A Vacuum Retort Pilot-Plant For Distillation Of Alloys, Robert Frederick Doelling

Masters Theses

"The widespread appearance of large scale vacuum systems operating commercially in the micron range of pressures has initiated a new field of industrial endeavor, vacuum engineering. The ever increasing number of applications of vacuo in commercial processes and laboratory research has stimulated the design and improvement of vacuum equipment, and at the present time equipment may be obtained to meet practically any need. In turn, the variety of available tools has directed the engineers attention to improving old processes and developing new ones through the utilization of vacuum techniques ... The possibility of producing a relatively high purity silver in …

The Freezing Temperatures Of The System Aniline-Ortho Toluidine, Ray W. Fahien

Masters Theses

"The purpose of this investigation was to determine the freezing temperatures of the system aniline-ortho toluidine and to speculate on the theoretical significance of these results. The properties of this system are of considerable practical engineering interest since the system falls in a class of low-freezing organic mixtures which may have value as fuels for jet propulsion devices required to operate at extreme altitudes or in Arctic regions. Since nitric acid has been found to be a very effective and convenient oxidizer, the search for a suitable fuel to be used in combination led to aniline as having the most …

Grouting And Freezing Unconsolidated And Water-Bearing Strata, Robert Walter Heins

Masters Theses

"The process of grouting has undergone many changes in recent years. A definition must, therefore, be inclusive. "Grouting" is the process of injecting, under pressure, into soil and rock through boreholes or other openings, any solution or suspension containing materials that harden, stiffen, or swell in void spaces to produce a solid or semi-solid impermeable mass. Various cements, chemicals, asphalts and clays are the materials used in the grouting process. The use of tailings is also considered a type of grouting, since some hardening or stiffening takes place. Cement grout relies on chemical reaction to bring about setting or hardening …

A Determination Of The Economic Feasibility Of Producing Marginal Gas Wells, Horace Tharp Mann

Masters Theses

"The purpose of this investigation is to show that it is economically feasible to produce marginal gas wells in such a manner that all the gas from the edge of the field will be captured by the first row of wells. In this problem the permeability of the sand is to be variable but known, and the effects of this variable permeability on the pressure distribution, and resulting gas production, will be discussed.

In many gas fields the point at which it is generally considered unprofitable to drill new wells is well inside the boundary of the reservoir. This is …

A Study Of Relative Ionic Mobility Of Alkali Ions In Dilute Alkali-Boron Trioxide Glasses As Deduced From Space Charge Considerations, Theodore J. Planje

Doctoral Dissertations

"The extensive investigations in the past have conclusively established that the alkali ions are responsible for the electrical conductivity of glass in both the brittle and viscous states; however, with the exception of one investigation in the brittle state, little consideration has been given to determination of the mobility of the alkali ion in such glassy systems. A review of the literature pertaining to the electrical conductivity of glass is presented.

A method, based on the rate of development of the ionic space charge responsible for polarization of conductivity cell employing direct current voltages, is proposed as a means for …

A Study Of The Dissolution Of Titanium In Acids With Emphasis On Hydrofluoric Acid, Ping-Chao Chen

Doctoral Dissertations

"Titanium is practically a new metal. Although it was discovered by W. Gregor in 1791, the pure metal was not prepared until 1910 by M. A. Hunter, and it is only very recently that tremendous interest has been focused on this new metal, as evidenced by the activities of numerous leading laboratories and pilot plants.

The reasons that Ti is gaining increasing attention may be attributed to the natural abundance of Ti ores in reasonable concentration and, what is more important, to its unusual combination of physical and chemical properties. According to F. W. Clark’s classical geochemical data, Ti amounts …

Measurement Of Flotation Rate As A Function Of Particle Size, Thomas Martin Morris

Doctoral Dissertations

“The Problem. The rate of flotation of solid particles determines the percentage recovery of these particles which can be obtained during a given time interval. An examination of operating data from a flotation plant shows that percentage recovery varies with the size of particle.

Many investigators have explored the problem of measuring flotation rate. In most cases the results obtained were expressed qualitatively. The results obtained by one worker were often at variance with results reported by another worker.

This investigation was undertaken with the object of (1) quantitatively measuring the rate of flotation of various sizes of particles and …

A Report On The Reduction Of Sphalerite Under Reduced Pressure, John H. Fuqua, William H. Magruder

Missouri School of Mines and Metallurgy Reports

During the last war, with the increased demand for magnesium metal and the general disregard for costs, a number of plants were constructed for the production of magnesium by vacuum metallurgical methods. (Both the Carbothermic Process and the Pidgeon Ferrosilicon Process employ vacuum systems for the production of metallic Mg.)

At the close of the war several of the government built plants were forced to suspend operations because of the economic impossibility of producing magnesium in competition with the Dow Chemical Company. It was with the availability of these plants in mind that experimentation with the possibilities of producing metallic …

Light Gage Steel Design Manual, American Iron And Steel Institute

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.