Open Access. Powered by Scholars. Published by Universities.®

Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

Missouri University of Science and Technology

Discipline
Keyword
Publication Year
Publication
Publication Type
File Type

Articles 19441 - 19470 of 21777

Full-Text Articles in Engineering

Mass Transfer From Spherical Gas Bubbles And Liquid Droplets Moving Through Power-Law Fluids In The Laminar Flow Regime, Robert M. Wellek, Cheng Chun Huang Jan 1970

Mass Transfer From Spherical Gas Bubbles And Liquid Droplets Moving Through Power-Law Fluids In The Laminar Flow Regime, Robert M. Wellek, Cheng Chun Huang

Chemical and Biochemical Engineering Faculty Research & Creative Works

Calculated mass transfer coefficients for the continuous phase are presented for internally circulating spheres of a Newtonian fluid traveling through a power-law-type continuous phase in the so-called creeping-flow region. The Nakano and Tien stream functions allow the Sherwood number to be computed as a function of the Peclet number, power-law index, and a viscosity ratio parameter. The Hirose and Moo-Young relation is shown to be a limiting case of this numerical solution. Mass transfer rates increase as the fluids become more pseudoplastic and/or the continuous phase consistency index increases, all other factors held constant. © 1970, American Chemical Society. All …

Go to article

On The Longitudinal Impact Of Two, Thin, Viscoelastic Rods, A. G. Behring, R. B. Oetting Jan 1970

On The Longitudinal Impact Of Two, Thin, Viscoelastic Rods, A. G. Behring, R. B. Oetting

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A one-dimensional representation of the distribution of stress and strain resulting from the longitudinal impact of two elastic rods is developed. A form of the "correspondence principle" is then used to obtain series solutions for stress and strain distributions resulting from the longitudinal impact of two rods of a "Maxwell material." Results of the viscoelastic solutions, obtained by use of nondimensional variables, are presented graphically. © 1970 by ASME.

Go to article

Excitation Requirement For Rectified Output Ac Generators, Richard Thomas Smith Jan 1970

Excitation Requirement For Rectified Output Ac Generators, Richard Thomas Smith

Electrical and Computer Engineering Faculty Research & Creative Works

This paper develops a method for calculating the required dc field current of a three-phase synchronous ac generator for known dc load conditions and machine characteristics. The method is simple to apply and has shown good agreement with test data. The method is of utility for preliminary design and analysis of rectified output alternators, such as may be used in excitation systems of the largest ac generators, space vehicle power applications, or high-power industrial rectification. Copyright © 1971 by The Institute of Electrical and Electronics Engineers, Inc.

Go to article

The Cathodic Reduction Of Bromate Ions On Mercury In Neutral And Basic Solutions, Jaw-Shin Chang Jan 1970

The Cathodic Reduction Of Bromate Ions On Mercury In Neutral And Basic Solutions, Jaw-Shin Chang

Masters Theses

"The reduction of BrO⁻₃ was studied in neutral and basic solutions on a stationary Hg surface under activation controlled conditions. Coulombic efficiency studies showed that BrO⁻₃; was reduced to Br⁻ with high efficiencies. The polarization measurements lead to a proposed reaction scheme which is consistent with the experimental observations"--Abstract, page 1.

Go to article

On The Flow Near An Enclosed Rotating Blade In The Neighborhood Of The Ground, Tze-Lien Liang Jan 1970

On The Flow Near An Enclosed Rotating Blade In The Neighborhood Of The Ground, Tze-Lien Liang

Masters Theses

"The flow in the vicinity of an enclosed rotating blade near the ground was studied both analytically and experimentally. Experimental results were obtained by making pitot tube traverses across the face of the housing but gave only a qualitative indication of the velocity distribution. Tufts of strings were used to locate the flow directions in the vicinity of the ground and the housing. The two dimensional potential flow solution was found to yield unreasonable results for this flow configuration due to viscous and rotative effects. The three-dimensional Navier-Stokes equations were solved numerically by using the successive underrelaxation method. The results …

Go to article

Fate And Effects Of Chemically-Precipitated Phosphorus In Anaerobic Digestion, Douglas Wayne Max Jan 1970

Fate And Effects Of Chemically-Precipitated Phosphorus In Anaerobic Digestion, Douglas Wayne Max

Masters Theses

"This study was conducted to determine the fate of chemically-precipitated phosphorus during the overall wastewater treatment process under actual field conditions. Specific objectives were: to evaluate the removal of phosphorus with alum and sodium aluminate in a pilot plant activated sludge system, to determine the fate of the precipitated phosphorus incorporated into the microbial floc when placed in an anaerobic environment, and to observe the effect of aluminum on the digestion process. Five 38-gpd continuous-flow activated sludge pilot plant units were operated at the Rolla Love Creek trickling filter plant and were fed with settled domestic sewage. The sludge from …

Go to article

Electric Field Strength Dependence Of Surface Damage In Oxide Passivated Silicon Planar Transistors, C. A. Goben Jan 1970

Electric Field Strength Dependence Of Surface Damage In Oxide Passivated Silicon Planar Transistors, C. A. Goben

Electrical and Computer Engineering Faculty Research & Creative Works

A dependence of surface degradation induced by ionizing radiation in matched oxide-passivated silicon planar epitaxial transistors on junction fringing electric field strength present during exposure is reported. The electric field strength and gamma dose dependence are investigated of the decrease in the forward current gain, hFE (as reflected by the increase in the surface recombination current component), the increase in the surface recombination velocity (as reflected by the increase in the reciprocal of the minority carrier lifetime), and the increase in junction capacitance. Empirical prediction equations have been derived, for matched devices, correlating the normalized base current increase and the …

Go to article

Baseband Agc In An Am-Fm Telemetry System, Richard S. Simpson, William H. Tranter Jan 1970

Baseband Agc In An Am-Fm Telemetry System, Richard S. Simpson, William H. Tranter

Electrical and Computer Engineering Faculty Research & Creative Works

The use of AGc loops at the input and output of the FM link in an AM-FM telemetry system allows the mean-square transmitter deviation to be maintained near maximum value, even though data may be nonstationary. However, errors result because of the inability of the receiver AGc loop to track perfectly gain variations in the transmitter loop. In this paper the general characteristics of AGc are discussed, and a theoretical analysis is performed to determine the time constant, steady-state error, and tracking error for a first-order loop. Also, tracking error for first order and second-order loops is investigated by simulation. …

Go to article

Penetration In A Graded Filter, William Chuan Shen Jan 1970

Penetration In A Graded Filter, William Chuan Shen

Masters Theses

"An experimental laboratory study conducted to examine clogging within and penetration of fines into a single layer graded filter. Hydraulic gradient, filter gradation and flow direction were varied. Forty one tests gave over six hundred individual penetration depths. The magnitude of penetration in filters with considerable variation in gradation patterns correlated with an average hydraulic radius based on the volume of voids and an approximated total surface area. It has been shown than an increased thickness of poorly graded filter will stop penetration such as that caused by seepage erosion. A relationship between hydraulic radius, penetration depth and probability of …

Go to article

A Study Of The Composite Action Of Light Gage Steel Deck And Concrete, Charles Sherman Bach Jr. Jan 1970

A Study Of The Composite Action Of Light Gage Steel Deck And Concrete, Charles Sherman Bach Jr.

Masters Theses

"This thesis is on the investigation of corrugated light-gage steel sheets used as the tension reinforcement for concrete slabs. The steel sheets used had embossments placed at uniform intervals over the entire length of the sheets. The composite concrete and light-gage deck steel were tested to determine a method of design for this type of composite section from an economical, safe and practical standpoint. The investigation covered the flexural, shear and bond capacity of this type of composite section"--Abstract, page ii.

Go to article

Evaluation Of Cascaded Inertial Vibration Isolation Systems, Rajnikant Bhikhabhai Patel Jan 1970

Evaluation Of Cascaded Inertial Vibration Isolation Systems, Rajnikant Bhikhabhai Patel

Masters Theses

"Cascaded inertial vibration isolation systems are examined in this report. Systems employing one, two or three masses in series on isolators are investigated. The objective is to determine if the cascaded systems have appreciable advantages over the classical single mass system. The equations of motion for these systems are derived by applying Newton's second law of motion. The homogeneous and steady state sinusoidal excitation solutions have been established. Transmissibility of forces and moments to the foundation has been obtained for several cases of force excitation. Comparisons of the cases investigated are based upon the principal mode frequencies, mode shapes, center …

Go to article

A Systematic Study Of Instrument Variables Upon The Accuracy Of Microprobe Analysis, R. A. Parr Jan 1970

A Systematic Study Of Instrument Variables Upon The Accuracy Of Microprobe Analysis, R. A. Parr

Masters Theses

"The purpose of this investigation was to study the effect of instrument parameter changes upon X-ray intensity measurements of the copper-manganese system. The parameters utilized in this study included: (1) polished, contaminated, and 600 grit surfaces ; (2) constant sample current and constant beam current modes; and (3) 15 KV, 20 KV, and 25 KV accelerating potentials. Inspection of the data disclosed three interesting points: (1) copper and manganese X-ray intensity measurements appear to be a linear function of composition in the 15 KV through 25 KV accelerating potential range; (2) electron backscatter measurements consistently show in a limited range …

Go to article

Influence Of Film Thickness On The Performance Of Solid Lubricants, Sunil Vishwanath Mahale Jan 1970

Influence Of Film Thickness On The Performance Of Solid Lubricants, Sunil Vishwanath Mahale

Masters Theses

"The object of this investigation was to determine the effect of lubricant film thickness on the coefficient of friction and on the wear life of solid lubricants. Bonded molybdenum disulphide and bonded graphite were the lubricants tested. Dow Corning's LFW-1 and Falex lubricant tester were the two machines used for testing these lubricants. The lubricants were sprayed on the specimen surface. Pretreatment, spraying and curlng were done according to standard or manufacturer's recommended procedures. During the entire research, the procedure for experimentation was followed according to ASTM No. 2625 on Falex and CRC recommendations on LFW-1 machine. It was found …

Go to article

Analysis Of Elastic Thermal Stresses By Station-Function Collocation Methods, Jaw-Kuang Wang Jan 1970

Analysis Of Elastic Thermal Stresses By Station-Function Collocation Methods, Jaw-Kuang Wang

Masters Theses

"An approximate method for the solution of thermal stress problems is presented. The method makes use of polynomial approximations to reduce the partial differential equation to a system of linear algebraic equations or a set of first-order ordinary differential equations. This results in satisfying the differential equation at a finite number of stations. The boundary conditions are satisfied identically. Two examples of the method, presented in detail, indicate that the solutions of the biharmonic equation for the stress function and the Fourier equation for the temperature distribution have good accuracy with a minimum of labor. A generalized method is derived …

Go to article

An Sem Surface Study Of Nucleate Pool Boiling Heat Transfer To Saturated Liquid Nitrogen Reduced Pressures From 0.1 To 0.9, David Virgil Porchey Jan 1970

An Sem Surface Study Of Nucleate Pool Boiling Heat Transfer To Saturated Liquid Nitrogen Reduced Pressures From 0.1 To 0.9, David Virgil Porchey

Doctoral Dissertations

"This study constituted an examination of both nucleate boiling and maximum heat flux characteristics of liquid nitrogen boiling from characterized surfaces. Several textures of gold plated copper surfaces were studied in addition to silver and silver oxide surfaces. Data were taken over a wide range of reduced pressures. All surfaces were examined using a Scanning Electron Microscope (SEM). Data and micrograph comparison revealed that both surface chemistry and surface roughness affect the nucleate boiling characteristics of liquid nitrogen. These effects are separated from each other showing that nucleate boiling is a function of both surface chemistry and topography. Surface roughness …

Go to article

A Study Of The Anodic Oxidation Of 1, 3-Butadiene On Platinum And Gold Electrodes, Arun Kumar Agrawal Jan 1970

A Study Of The Anodic Oxidation Of 1, 3-Butadiene On Platinum And Gold Electrodes, Arun Kumar Agrawal

Doctoral Dissertations

"The anodic oxidation of 1,3-butadiene on Pt and Au electrodes was studied at 70°C in solutions of H₂SO₄, K₂SO₄, K₂CO₃, and KOH with pH's ranging from 0.35 to 12.5. Reaction rates (current) were measured as a function of potential, pH, temperature, and butadiene partial pressure. A transition region (apparently a shift in the rate determining step) in case of Pt was observed in the Tafel plots. The coulombic efficiencies of oxidation to CO₂ were 85 percent in 1 N H₂SO₄ on Pt, 93 percent in 1 N KOH on Pt, and 72 percent in 1 N KOH on Au"--Abstract, Page …

Go to article

Abandoned Automobiles :A Case History Of Land Pollution, Robert William Arden Jan 1970

Abandoned Automobiles :A Case History Of Land Pollution, Robert William Arden

Masters Theses

"A study has been made of the abandoned automobile problem as it now exists throughout the United States with particular emphasis on the problem in the Saint Louis area. The primary goal of this study was to determine those factors which most influence the collection and disposal of derelict vehicles. The problem was examined in the following major areas: (1) The history of the problem in the Saint Louis area and the various attempts made to correct it, (2) the various businesses directly involved with the disposal of junk automobiles, namely, the auto wreckers and the scrap processors, and (3) …

Go to article

The Development And Analysis Of A System To Measure Transient Angular Velocity, David Lawrence Persson Jan 1970

The Development And Analysis Of A System To Measure Transient Angular Velocity, David Lawrence Persson

Masters Theses

"A measuring system was built to provide a D. C. voltage which was proportional to the angular speed of a particular rotating shaft under question. The measuring system developed has a time constant of approximately .00365 seconds. The final measuring system was developed after trying various other means which proved unsatisfactory. The final device developed would be quite satisfactory in a wide variety of applications"--Abstract, page ii.

Go to article

The Closed Cycle-External Combustion Engine And Air Pollution, Galen Lee Pearson Jan 1970

The Closed Cycle-External Combustion Engine And Air Pollution, Galen Lee Pearson

Masters Theses

"The impact of the internal combustion engine on the air pollution problem in this country was presented and alternative propulsion systems for the land transportation vehicle were investigated. The potential characteristics of the more promising closed cycle-external combustion engine concepts were established and discussed. The closed thermodynamic power cycles analyzed include the Rankine, Stirling, and Feher supercritical cycles. Thermodynamic property data on eighteen candidate working fluids for the Rankine and Feher supercritical power cycles have been assembled and were presented in a utilizable form. The thermal efficiency (ratio of the net work out to the heat input) and the many …

Go to article

The Anodic Dissolution Of Molybdenum In Acidic Nitrate Solutions, Kuan-Hsiung Hoh Jan 1970

The Anodic Dissolution Of Molybdenum In Acidic Nitrate Solutions, Kuan-Hsiung Hoh

Masters Theses

"The anodic dissolution of molybdenum in 1.0 N HNO₃ (pH = 0.3) , 0.1 N HNO₃-0.9 N KNO₃ (pH = 1.2), and 0.01 N HNO₃ -0.99 N KNO₃ (pH = 2.1) was investigated. The following conclusions were possible: 1. Mo is in general electrochemically oxidized to the Mo-VI state during anodic dissolution. 2. The resultant ions in solution are HMOO⁻₄. 3. The Mo surface in aqueous solutions is covered with an oxide whose approximate composition is Mo₂O₅. 4. The polarization curves have a linear Tafel region at potentials slightly above the rest potential. 5. There is no significant effect of …

Go to article

Dynamic Analysis Of Multistory Frames Considering Both Distributed And Lumped Mass, Mark E. Botkin Jan 1970

Dynamic Analysis Of Multistory Frames Considering Both Distributed And Lumped Mass, Mark E. Botkin

Masters Theses

"Two types of dynamic analysis of multistory structures are presented in this thesis . First presented is the dynamic stiffness matrix method in which the masses are distributed along the constituent members. This method is composed of statics, stiffness and loading matrices. The statics matrices are established from the structural configurations, the stiffness coefficients are formulated from the elastic properties of the members, and the loading matrices are functions of the time dependent forces or time dependent foundation movements. The applied forces may be uniform, concentrated, triangular or joint forces. Computer programs are given to carry out the laborious calculations …

Go to article

An Analysis Of A Synchronization Scheme For 180° Biphase Modulated Signals, James Joseph Spence Jan 1970

An Analysis Of A Synchronization Scheme For 180° Biphase Modulated Signals, James Joseph Spence

Masters Theses

"The problem of analyzing a synchronization system for demodulation of 180° biphase modulated signals is considered in this thesis. The system considered utilizes the so-called squaring loop technique. Techniques derived from the theory of Markov processes are utilized in the analysis of the system. In particular the "fluctuation equation" approach for non-Markovian processes is used. After the analysis of the system is performed, an expression fro the bit error probability is obtained from knowledge of the phase error density function"--Abstract, Page ii.

Go to article

Anodic Dissolution Of Zinc In Potassium Bromide-Potassium Bromate Solutions, Ying-Cheh Chuang Jan 1970

Anodic Dissolution Of Zinc In Potassium Bromide-Potassium Bromate Solutions, Ying-Cheh Chuang

Masters Theses

"The purpose of this investigation was to study the anodic dissolution of zinc at a temperature of 25°C in Br⁻-BrO₃; solutions. In Br⁻ solutions, it was found that the apparent valences of zinc ions going into solution were approximately the normal value of two. Smaller values were obtained in BrO⁻₃ solutions, with the most pronounced changes occurring in the higher concentrations of BrO⁻₃. An empirical equation was derived relating the apparent valence (zi) to the current density (amp·cm⁻²) and BrO⁻₃ concentration (gmol/liter): 2- zi = 3.11 X i⁰̇̇¹³(CBrO⁻₃)⁰̇⁵⁷ The mechanism for the dissolution of zinc …

Go to article

Measurement Of Thermal Accommodation Coefficients Of Steel Surfaces, Wing On Ho Jan 1970

Measurement Of Thermal Accommodation Coefficients Of Steel Surfaces, Wing On Ho

Masters Theses

"The thermal accommodation coefficient plays an important role in low density thermal energy transfer measurement. The object of this investigation was to measure the thermal energy transfer between a heated test surface and a water cooled reference surface (flat black lacquer) consisting of two infinite concentric cylinders separated by dry air. Two machined and sanded steel cylinders with mean surface roughnesses of 25 microinches and 7.5 microinches were used as the test surfaces . Measurements were made in the pressure range of 1.2 x 10⁻⁶ mm Hg. to 1.8 x 10⁻⁶ mm Hg. and temperature range for test cylinders of …

Go to article

A Computer Simulation Of The Internal Ballistics Of Recoilless-Rifle Rocket Launchers, John Edd Mosier Jan 1970

A Computer Simulation Of The Internal Ballistics Of Recoilless-Rifle Rocket Launchers, John Edd Mosier

Masters Theses

"A computer program has been developed to simulate the basic mechanics and gas dynamics associated with launching a solid propellant rocket from a recoilless rifle. This program, entitled "KICKIT," may be used to predict the performance and evaluate many of the pertinent design parameters of both conventional recoilless rifles and a recoilless rocket launcher system. This program is a valuable analytical tool which enables the designer either to optimize the system design or predict the behavior of the system under off-design conditions"--Abstract, Page ii.

Go to article

Digital Simulation Of A Costas Loop Demodulator In Gaussian Noise And Cw Interference, Ajay Mugatlal Mehta Jan 1970

Digital Simulation Of A Costas Loop Demodulator In Gaussian Noise And Cw Interference, Ajay Mugatlal Mehta

Masters Theses

"A digital computer model of a Costas loop has been employed to study the effects of Gaussian noise and continuous-wave interference on the detection of biphase modulated signals. The dependence of bit-error probability, mean-square error between input and output, phase-error variance and threshold on signal-to-Gaussian-noise power ratio, interference-to-Gaussian-noise power ratio and frequency offset of the interference have been investigated and compared with previously obtained experimental results. The model has been verified for its accuracy in the case of no noise and when Gaussian noise is present at its input"--Abstract, Page ii.

Go to article

Study Of Neutron Reflection From A Curved Surface Using The Monte Carlo Method, Marion Jay Rackley Jan 1970

Study Of Neutron Reflection From A Curved Surface Using The Monte Carlo Method, Marion Jay Rackley

Masters Theses

"The reflection patterns for neutrons impinging on both an infinite parabola and an infinite slab were studied using the Monte Carlo method. In the first case neutrons were sent into an infinite parabola (z =x²/2) moving on the XZ plane parallel to the z axis at 5 points, namely: y = 1.5, x = -1.5; y = 1.5, x = -.75; y = 1. 5, x = 0. 0; y = 15, x =.75; y = 1.5, x = 1.5. The results were that there appeared to be a "focusing" of the scattered neutrons. In the second case, neutrons were …

Go to article

Analysis Of Parking Conditions At The University Of Missouri - Rolla And Their Comparison To Other Universities, Richard Francis Rankin Jan 1970

Analysis Of Parking Conditions At The University Of Missouri - Rolla And Their Comparison To Other Universities, Richard Francis Rankin

Masters Theses

"The existing parking facilities at the University of Missouri - Rolla are presently inadequate and parking demand will continue to increase in the coming years. Factual study of existing conditions by means of physical vehicle counts indicate that operational efficiency can be increased as a method of reducing the parking shortage. It was determined, by a faculty and staff questionnaire, that the automobile was not greatly required in order to carry out university business. A faculty residence density study indicated that the majority of the faculty members live farther than 7/10 of a mile from the campus. Present methods of …

Go to article

Z-Form Solution Of Non-Linear Differential Equations, Allen Joseph Rushing Jan 1970

Z-Form Solution Of Non-Linear Differential Equations, Allen Joseph Rushing

Masters Theses

"The "Z-Forms" developed by Boxer and Thaler from Z-Transform theory are reviewed. Iteration is shown to increase accuracy when Z-Forms are used to obtain numerical solutions to some non-linear differential equations. Machine results are presented for example problems. Error estimates and convergence conditions are discussed. The method is usable only when 2- or 3-digit accuracy is acceptable. For some classes of equations the Z-Form method compares favorably to other numerical methods in time required to set up the problem and in machine time required for solution--Abstract, Page ii.

Go to article

Fault Detection On Sequential Machines, Chung-Tao David Wang Jan 1970

Fault Detection On Sequential Machines, Chung-Tao David Wang

Masters Theses

"This paper presents an algorithm for deriving an optimum test sequence for detecting faults in a synchronous machine. In this study, the flow table is used as a tool to generate the fault detection tests. The fault stuck-at-1 (or stuck-at-0 ) is said to be present when a permanent signal valued 1 (or 0) appears on a component of the machine. Only single faults are treated . The result of the procedure is one or more test sequences guaranteed to detect a set of faults (Fp). First, sequential machines with feedback lines as memory elements are considered . …

Go to article

First Prev Next Last