Engineering Commons^™

Power, Divergence, And Stability Factors Affecting The Use Of A Krypton Laser As A Multispectral Illumination Source, David Perry Owsley

Masters Theses

"Specific performance characteristics of a krypton laser were measured. Evaluation criteria were dictated by the proposed use of the laser as a multi-wavelength illumination source. The laser output power, spectral power distribution, and output stability were measured as a function of wavelength and transverse mode order, to determine optimal operation characteristics. Data are presented defining the compromise between laser output power and beam divergence when the laser is operated multi-wavelength, and in several low-order transverse modes. There is an advantage of increased output power when the laser is operated in transverse modes higher in order than TEM₀₀, but …

Nucleate Pool Boiling Of Refrigerant-Oil Mixtures From Tubes, R. L. Dougherty

Masters Theses

"This experimental investigation was conducted to provide design heat transfer data for applications involving the nucleate pool boiling of Refrigerants 11 and 113 from the external surfaces of tubes. Tests were conducted with 0.625-in. o.d. and 1.125-in. o.d. commercial copper tubing; at 1 and 2 atmospheres pressure; and with refrigerant-oil compositions from 0 to 10 percent oil by weight. Results show that each of these parameters can affect the heat transfer coefficient"--Abstract, page ii.

The Effect Of Porosity On Strength Degradation In Thermally Shocked Alumina, Russell David Smith

Masters Theses

"Strength degradation and crack propagation in Al₂O₃ are shown to depend on the initial strength and porosity of the material. Specimens were fabricated containing between 0 and 5% induced cylindrical, two dimensional, and spherical porosity. The strengths of the various porosity samples decreased discontinuously at a critical quenching temperature. No difference was observed in the critical temperature for the various aluminas; initial strength decrease occurred between 165°C and 175°C temperature differential. The strength retained after thermal shock decreased with increasing initial strength. The degree of damage sustained upon shocking was also characterized by crack density and crack …

Calculation Of Gamma-Ray Albedo Using The Monte Carlo Method, Ezatholah Aslani-Amoli

Masters Theses

"Gamma-ray number, energy and dose albedo are calculated with the Monte Carlo technique. A plane monoenergetic beam was considered at normal incidence upon single material shields at initial gamma energy up to 10 MeV. Aluminum, iron and lead are used as shield material. The contribution of secondary photons which are produced as a result of various photon interactions in the shield are taken into account. These secondary photons are annihilation gammas, X rays and bremsstrahlung gammas. In certain cases, they constitute a considerable fraction of the reflected radiation.

Annihilation gammas predominate in the reflected radiation for all energies above 1.02 …

Nutation Control During Precession Of A Spin-Stabilized Spacecraft, Richard James Donner

Masters Theses

"The effects of precession thrust pulses and energy dissipation upon nutation of a spin-stabilized spacecraft are studied. Methods for controlling nutation during a precession maneuver are proposed and examined. In particular, a precession modulation control law is developed which uses precession thrust pulses to control nutation. Digital simulations show that precession control with separate nutation control is the fastest precessing system; however, the precession modulation method is only fractionally slower while not requiring a separate nutation control system"--Abstract, page ii.

Parametric Resonance Of A Beam Subjected To A Sawtooth, Axial Force, Alfred George Richardson

Masters Theses

"This study considers the response of a perfectly elastic straight beam subjected to a periodic, non-harmonic, axial load. A two-mode solution is sought and the effects of axial inertia are included in the analysis. General equations of motion for the beam are developed and their stability is studied with the aid of an analog computer. Results are presented in graphical form. Regions of instability are defined for both modes. A region of combination resonance is also found to occur for the case of a two-mode solution with axial inertia. Typical response curves are presented and the effects of axial inertia …

A Travelling-Wave Transistor Amplifier, Manit Kovintha

Masters Theses

"This thesis discusses a steady-state analysis and design of a coupled uniform travelling-wave transistor amplifier. A solution to the problem is given in closed form and a numerical method for evaluating the solution is discussed.

Practical line parameters and different terminations are used in frequency response calculations. The amplifier power gain variations due to parameter variations are considered and shown in full"--Abstract, page ii.

Mass Transfer Coefficients Determined By Simplex Optimization Techniques, Charles Ferris Callihan

Masters Theses

"The objective of this thesis is to develop a method for obtaining individual mass transfer coefficients in absorption columns. There are two assumptions which apply throughout the thesis. The first assumption is "plug flow." The second assumption is that the axial concentrations can be measured accurately enough.

The problem is approached by simulating data generated from a mathematical model of an absorption column. A response surface is defined which is a function of the individual mass transfer coefficients. The lowest point on the surface locates the individual mass transfer coefficients for the system in question.

The mathematical model of the …

Pollution Abatement Of Mining Effluents In The New Lead Belt Of Missouri, Walter Armando Escalera

Masters Theses

"The mining and milling effluents from the Buick Mine of the AMAX Lead Company of Missouri have produced undesirable algal growths in Strother Creek below their tailings pond. A field and laboratory study was performed to determine the characteristics of the mining and milling wastewaters, and to study the effects of heavy metals and nutrients on algal growths. Laboratory studies included: Physico-chemical analysis of the wastewater; determination of heavy metal concentrations; algal growth studies in an experimental model; and microscopic examinations of the algal growths. Field work comprised: A study of the mining and milling operations; in-plant investigations of the …

The Effect Of Gating On Soundness Of Al-Alloy Permanent Mold Castings, Dinesh Shantilal Patel

Masters Theses

"This thesis describes the step by step approach to the design of a gating system for the production of sound plate castings in permanent molds. Castings of different thicknesses were produced, utilizing various gating systems, and examined radiographically to evaluate the effectiveness of these gating systems in the production of sound castings. A gating system which allows metal to enter the mold cavity with no turbulence and which establishes proper temperature gradients in the casting will produce sound permanent mold castings"--Abstract, page ii.

Neutronics Calculations Of Two Fusion Reactor Blankets, James Edward Struve

Masters Theses

"At the present state of engineering development, the most probable fusion reactor fuel cycle will use deuterium and tritium in the reaction ²₁D + ³ ₁T → ¹₀n + ⁴₂He. This reaction is exothermic and provides 17.6 Mev of energy of which 14.1 Mev are given to the neutron. The reaction will take place in a plasma environment inside an evacuated chamber. This chamber will be surrounded by a "blanket" which will serve to transform the kinetic energy of the neutron into heat and produce tritium for subsequent use in the fuel cycle. …

Marshall Properties Of Asphaltic Concrete Containing Glass-Rich Fractions, James Joseph Schneider

Masters Theses

"The use of crushed waste glass as an aggregate in asphaltic concrete has been suggested as a means for re-using glass separated from municipal refuse. Laboratory studies and field installations have generally utilized clean glass obtained by hand sorting bottles from the other refuse and crushing them to produce a desired gradation. For this type of asphalt to be economical though, the glass fraction must be separated mechanically. For mechanically separated materials, the glass-rich fraction also contains such items as metal, bone, rubber and other non-glass materials.

The objective of the study was to determine the effects upon Marshall properties …

Sintering And Microstructure Control Of A Ferrimagnetic Mn-Zn Ferrite Spinel, Joel Keith Michel

Masters Theses

"The effect of minor additions of CaO dopant to a manganese zinc ferrite – Zn_.25Mn_.75 Fe_2.17 O_4.0 - on its grain growth and densification kinetics in air at 1250°C., 1300°C., and 1350°C. was studied. Grain growth was controlled over a range of dopant levels. At a sintering temperature of 1350°C. and time of six hours a ferrite with the smallest dopant addition was sintered to the highest density - 98% of theoretical. Under the same sintering conditions ferrites with higher dopant levels also sintered with normal growth but sintered to lower densities.

Due to discontinuous …

Stability Of Filled Cylindrical Shell Columns, Yu Wen Tsao

Masters Theses

"This experimental investigation was conducted to study the stability of filled cylindrical shell columns. Two kinds of filler materials, flower clay (florist clay) and silica sand, were investigated. The cylindrical shells were made of 2024-T3 Reynolds aluminum tubing. Uniaxial compressive loading was applied directly to the filler materials through two loading rams, one at each end of the cylinder, (no loading was applied directly to the shell). Tests for investigating the load transmitting characteristics of the filler materials were performed, and the states of the stresses existing in the cylindrical shells were then obtained.

The buckling formula for thin-walled cylindrical …

Digital Fault Calculations Of Large Systems Using Matrix Language And Generalized Equations, Saeed Abdel-Halim Khalifa

Masters Theses

"A new short circuit program has been developed for a large system. Several features have been provided to simplify handling of the system data. Various study cases are performed, efficiently, within the available computer memory. A master data bank is established from bus, feeder and transformer data. They can be modified internally to simulate various system configurations. Matrix formation is accomplished using a new sorting method and the IBM/360 Matrix Language MATLAN. A generalized set of ii ·equations have been developed and applied to calculate four types of faults.

The program consists of two phases of operations. In phase-1, input …

Break-Even Criteria For A Pulsed D-T Reactor, Kenneth Franklin Keller

Masters Theses

"To those who keep track of such things and are in a position to make predictions, it appears that the use of controlled thermonuclear reactions to economically produce electric power is well within a lifetime from now. Indeed, experiments presently being conducted are putting us closer and closer to the development and construction of demonstration fusion reactors. Understandably, the people working on such products and processes are optimistic about their results. This is as it should be if our nation is to avoid major energy shortages in the future.

Unfortunately, the tenor of this paper is pessimistic. This is not …

Use Of Radioactive Iodine Evolved Into Reactor Cooling Water To Locate Defective Fuel Elements, Carl Mozel Stroud

Masters Theses

"The relative amount of radioactive iodine evolved in reactor cooling water by each fuel element provides an excellent indication of defective cladding on fuel elements. The radioactive iodine evolved into the reactor cooling water from a defective fuel element should be higher than the average radioactive iodine evolved by other fuel elements into the cooling water by an order of magnitude or more.

Radioactive iodine with non-radioactive iodine carrier is adsorbed on DOWEX SBR resin in the iodide form. The iodide is eluted from the resin with sodium hypochlorite and extracted into carbon tetrachloride. The iodine is reduced to iodide …

A Survey Of Missouri's Water Resources Involvement, Frank R. Ellis Ii

Masters Theses

"A survey of the procedures for development of water resources in the State of Missouri reveals shortcomings in many areas. Recommended improvements include: 1) revising and publishing a statewide water plan, 2) improving methods of project evaluation and priority establishment, 3) expanding methods of citizen involvement, and 4) reorganization of state agencies and legal authority. The paper examines the history of water resource involvement by the State of Missouri, and current jurisdiction of state agencies, including procedures for review of environmental impact statements"--Abstract, page iv.

Heat Transfer Of A High Prandtl Number Oil In Laminar Flow, John Robert Lee Iii

Masters Theses

"A numerical model was developed for the purpose of studying the flow and heat transfer of a hypothetical oil in laminar flow within a horizontal pipeline. Free convection, work of compression, and axial conduction were neglected, but the fluid properties - i.e., density, specific heat, viscosity, and thermal conductivity - were allowed to vary and the effect of viscous dissipation was included in the analysis of the system.

The mathematical forms of the momentum, continuity, and energy equations require that numerical solutions be obtained with a digital computer. These numerical approximations of the partial differential equations are presented and the …

Analysis And Design For Semi-Automatic And Automatic Control Of Vehicles By Permanent Magnets, Hari K. Mehta

Masters Theses

"The analysis and design carried out in this study relates to automatic or semi-automatic lateral control of a vehicle. This is one of the three essential subsystems needed for a complete automatic control system. The other two subsystems provide longitudinal control, and intersection or lane-changing control.

The system studied employs a series of permanent magnets which have been embedded vertically in the road and spaced at an interval to be used for position reference, leading to discontinuous error signal. This system has been analyzed by classical Z-transform analysis and control models have been developed for two kinds of controls. First, …

Thermal Radiative Properties Of A Semi-Infinite Absorbing-Emitting And Isotropically Scattering Medium, Tung-Ting Lam

Masters Theses

"The development and the approximate solution to the transport equation for a semi-infinite, absorbing, and isotropically scattering medium with a refractive index other than unity is presented. The general boundary condition of diffuse and collimated incidence at the interface with emission from the medium was considered by superimposing the individual effects. In each case the apparent properties, directional and hemispherical emittance, reflectance and transmittance, were evaluated as a function of the scattering albedo and the refractive index.

An exponential kernel substitution was developed and used to obtain the approximate solution. The method was evaluated by a comparison with existing but …

Approximate Normal Mode Method To Determine The Response Of Certain Nondiagonalizabel Vibratory Systems, Jayaram Seshadri

Masters Theses

"An approximate normal mode method is developed which permits certain normally nondiagonalizable, nonconservative systems to be solved by superposition of uncoupled coordinates.

An approximate solution for a nonproportionally damped, multi-degree of freedom system is obtained by using a perturbation technique. The system is then reduced to a proportionally damped system by means of a modification to the damping factor so that the effect of the off-diagonal terms of the modal damping matrix is included. This modification produces a damping matrix that can be diagonalized by the normal mode technique. An approximate criterion is used for the determination of the modified …

A New And Direct Process For The Reduction Of Lead Sulfide, Rolando Oscar Fernandez

Masters Theses

"The direct reduction of lead sulfide concentrates by iron was investigated. An oxygen-bearing flux was shown to be a necessary ingredient for complete reduction of the concentrate. The effects of time and temperature on lead recovery were studied. Only a trace amount of sulfur dioxide is evolved during reduction, which is in agreement with thermochemical calculations"--Abstract, page ii.

Breakdown Of The Laminar Flow Regime In Permeable-Walled Ducts, E. M. Sparrow, G. S. Beavers, T. S. Chen, J. R. Lloyd

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The stability of laminar flow in a parallel-plate channel having one permeable bounding wall is investigated by means of linear theory. The analysis lakes account of the coupling of the disturbance, fields in the channel and in the permeable material and of velocity slip at the surface of the permeable wall. Complementary experiments are performed in which the breakdown of the laminar regime in flat rectangular ducts is identified from pressure-drop measurements and from flow visualization studies. The experiments cover the range of slip velocities from 15-30 percent of the mean velocity and, in addition, the case of zero slip …

Decision-Directed Detector For Overlapping Pcm/Nrz Signals, Cheng Wang, Thomas L. Noack

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A decision-directed (DD) technique for the detection of overlapping PCM/NRZ signals in the presence of white Gaussian noise is investigated. The performance of the DD detector is represented by probability of error PE versus input signal-to-noise ratio (SNR). To examine how much improvement in performance can be achieved with this technique, PE's with and without DD feedback are evaluated in parallel. Further, analytical results are compared with those found by Monte Carlo simulations. The results are shown in good agreement. © 1973, IEEE. All rights reserved.

Letters To The Editor, J. T. Mason, Orrin K. Crosser, Robert D. Gunn, C. Judson King

Chemical and Biochemical Engineering Faculty Research & Creative Works

No abstract provided.

A Study Of Medium And High Internal Phase Ratio Water/Polymer Emulsions, Kenneth J. Lissant, Kenneth G. Mayhan

Chemical and Biochemical Engineering Faculty Research & Creative Works

Medium and high internal phase ratio water/polymer emulsions were studied utilizing scanning electron microscope techniques. Results are reported for the geometry and distribution of droplets for water/polymer ratios from 1 1 to 9 1. Electron micrographs confirm those models which predicts polyhedral droplet formation at high internal phase ratios. © 1973.

Experimental Analysis Of V-Belt Tensile Loads, John Mark Wiesehan

Masters Theses

"An experimental investigation was conducted to determine the magnitude of v-belt stresses in automotive drive situations. A constant tension belt test apparatus was designed and fabricated using a variable speed cradled D.C. motor for power and two automotive alternators for absorption.

Free span stresses on the dynamic torque loaded belt drive were determined from the equations governing a pivoted drive system. Centrifugal stress was determined by a theoretical analysis of belt motion. Bending stresses were obtained from a static test employing strain gages mounted on the top of belts with exposed cord layers. The variation in load stress around the …

Parameter Identification Applied To Linear Quadratic Differential Games, John D. Corrigan

Doctoral Dissertations

"A two player zero-sum linear quadratic differential game is investigated for the case in which one of the players has incomplete a priori knowledge of the parameters of his opponent's dynamic system. This incomplete system parameter information game is shown to be playable since the ignorant player can make limiting estimates of the unknown parameters from the relative controllability condition for the game. Performance from the ignorant player's point of view is suboptimal.

It is also shown that parameter identification techniques can be applied by the ignorant player in order to directly identify the smart player's closed-loop parameters in the …

A Digital Simulation Of A Single Articulated Rotor Helicopter, Joseph William Klahs Jr.

Masters Theses

"The investigation was concerned with the development of a complete digital computer simulation of a single articulated rotor helicopter. The simulation program was executed on an IBM model 360-50 digital computer.

The main rotor was analyzed by the consideration of a continuous rigid blade at six azimuth stations, while the airframe aerodynamics were treated in the conventional manner. The differential equations of motion of the airframe were solved in a step-wise fashion by approximating time dependent functions with cubic interpolation polynomials.

The study concluded that there was strong evidence that suggested the possibility of treating main rotor flapping as a …