Engineering Commons^™

Geochemical Assessment Of Mineral Sequestration Of Carbon Dioxide In The Midcontinent Rift, Alsedik Abousif, David J. Wronkiewicz, Abdelmoniem Masoud

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

This Study Examines The Potential Of Midcontinent Rift Rocks To Facilitate Long-Term CO2 Sequestration By Providing The Necessary Ca And Mg For Carbonate Mineralization. Surface Samples Were Collected From The Oronto And Bayfield-Jacobsville Groups Around Lake Superior And Used For Petrography And X-Ray Diffraction To Determine Their Mineral Composition. Also, X-Ray Fluorescence Was Also Used To Assess Their Bulk Chemical Composition. The Samples Were Then Exposed To CO2 And Deionized Water In Teflon-Lined Vessels At 90°C, And The Resulting Leachate Fluids Were Analyzed For The Cation Released During The Testing. SEM Microscopy Was Used To Examine The Samples For Potential …

Would Self-Supported Fracture Contribute To The Hydrocarbon Production In Shale Reservoir Besides Proppant-Supported Fracture, Y. Sun, G. Li, S. Zeng, J. Wu, J. Liu, M. Xu, C. Dai, Baojun Bai

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

During hydraulic fracturing in deep shale gas reservoirs, it is difficult to pump proppants long distances, and self-supported fractures are formed at the far and upper ends of the fractures. The self-supported fracture could hold the fracture space by its surface structure again fracture closure. However, it faces various aspects of impairment during shale gas reservoir development, which affect its conductivity. Among the impairment, long-term production results in a decline of bottom hole pressure, which will compact the fracture space, and self-supported fractures without proppant are more sensitive than those with proppant. In this paper, we conducted a series of …

Circular Economy Strategies For Reducing Embodied Carbon In Us Commercial Building Stocks: A System Dynamics Modeling Approach, Radwa Eissa, Islam H. El-Adaway

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Environmental concerns over embodied carbon - which is generated during the extraction, transportation, manufacturing, construction, and disposal of building materials - have been increasing as the industry shifts to renewable energy and grid decarbonization efforts prevail. Commercial buildings, a rapidly growing sector and a major source of embodied carbon, can contribute immensely to the national climate goals by transitioning into a circular economy (CE). Nevertheless, embodied carbon research is rather dispersed, with sparse data on the actual impact of different CE strategies and how they scale on nationwide commercial building stocks. To address this research need, the goal of this …

The Impact Of Journalistic Cultures On Social Media Discourse: Us Primary Debates In Cross-Lingual Online Spaces, Lea Hellmueller, Lindita Camaj, Sebastián Vallejo Vera, Peggy Lindner

Engineering Management and Systems Engineering Faculty Research & Creative Works

This cross-lingual project examines how social media posts of Spanish- and English-language media impact incivility in user comments during the 2020 primary political debates in the United States. We analyzed Facebook posts of news organizations that hosted the debates and used a state-of-the-art machine-learning model to analyze the corresponding comments. Our findings reveal distinct journalistic cultures on the post-level: English-language media are significantly more likely to use interpretation while Spanish-language media employ more audience-engagement and factual reporting strategies. We argue that in order to understand incivility in social media discourse during political debates, we need to consider journalistic cultures: While …

Fe-Ni-Cu-Pge Sulfide Transport Mechanisms And Carbon-Sulfur Interactions In Lower Crustal Magmatic Settings: A Study From The Valmaggia Ultramafic Pipe, Ivrea-Verbano Zone, Italy, Shelby Leann Clark

Masters Theses

"Constraining the processes that control the transport and deposition of sulfides in the deep lithosphere is an important step in expanding ore deposit exploration search space to include exhumed lower crustal rocks. The ultramafic sulfide ore-bearing Valmaggia pipe in the Ivrea-Verbano Zone of NW Italy, an exhumed cross section of the overlying lower continental crust and subcontinental lithospheric mantle, gives critical insight into metallogenic processes in lower crustal settings. The ~300 m wide metasomatized pipe hosts Fe-Ni-Cu-(PGE±Co±Au) sulfide mineralization that is commonly associated with locally abundant carbonates and hydrous silicates (phlogopite, amphibole). Previous studies suggested that sulfides were physically transported …

A Systematic Review Of Phenotypic And Epigenetic Clocks Used For Aging And Mortality Quantification In Humans, Brandon Warner, Edward Ratner, Anirban Datta, Amaury Lendasse

Engineering Management and Systems Engineering Faculty Research & Creative Works

Aging is the leading driver of disease in humans and has profound impacts on mortality. Biological clocks are used to measure the aging process in the hopes of identifying possible interventions. Biological clocks may be categorized as phenotypic or epigenetic, where phenotypic clocks use easily measurable clinical biomarkers, and epigenetic clocks use cellular methylation data. In recent years, methylation clocks have attained phenomenal performance when predicting chronological age and have been linked to various age-related diseases. Additionally, phenotypic clocks have been proven to be able to predict mortality better than chronological age, providing intracellular insights into the aging process. This …

Lidar Technology For Future Wireless Networks: Use Cases And Challenges, Omar Rinchi, Ahmad Alsharoa

Electrical and Computer Engineering Faculty Research & Creative Works

Next-generation wireless networks are beset with challenges such as line-of-sight (LoS) shadowing and multipath scattering, significantly impacting service quality and reliability. Despite technological advances aimed at mitigating these issues, achieving consistent quality of service (QoS) standards continues to be an uphill task, particularly within the ever-changing urban landscapes and the intricate process of melding new technologies with pre-existing infrastructures. This paper delves into the integration of light detection and ranging (LiDAR) sensors as a novel solution to these persistent problems. We explore two potential use cases of LiDAR integration in wireless networks, offering detailed insights into the underlying motivation, technical …

Generation Of Micro-Fracture Clouds In Rocks: Mechanisms And Applications, U. Mutlu, G. Boitnott, A. Lisjak, O. Mahabadi, Taghi Sherizadeh, D. Guner, S. Nowak, A. Ghassemi

Mining Engineering Faculty Research & Creative Works

Volume increasing or decreasing processes in rocks can lead to inter or intragranular fractures in subsurface formations. The volume change can be caused by chemical reactions involving fluid, reactive transport, and coupling with the mechanical deformation of the grains. Depending on stress, material properties and coupled thermo-hydro-mechanical-chemical (THMC) conditions, grain scale fractures may propagate and coalesce, forming a cloud of well-connected fracture networks. The mechanisms responsible for propagation, coalescence and inhibition of cloud fractures are not well known. In this study, we review coupled micro-fracture network generation mechanisms as published in the literature and observed in field, experiments, and models. …

Quantifying The Impact Of A Constructed Wetland On Downstream Nitrate Concentrations And Loads In The U.S. Midwest, Elliot Anderson, Keith E. Schilling, Craig L. Just, Bong Chul Seo

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Constructed wetlands are standard conservation practices used to reduce nitrate loads in agricultural watersheds. Many studies have examined the efficiency of denitrification in wetlands under various scenarios, but quantifying the watershed-scale impact of wetlands on downstream nitrate levels is rarely done using field observations. In this study, we estimated nitrate removal in a constructed wetland in the headwaters of Mud Creek, a HUC12 watershed in eastern Iowa, from May–September 2022 and May–September 2023 (a ten-month period). We also measured nitrate loads at four successive downstream sites, three along Mud Creek and one below its confluence with the larger Cedar River. …

Iterative Power Flow Control Architecture For Dc-Ac-Ac Triple Active Bridge Converters: Design, Simulation, And Hardware Testing, Jonathan Henri Saelens

Masters Theses

Driven by widespread electrification and escalating energy demands, efficient and cost-effective converter systems are necessary to maintain and improve our nation's electrical grid. Facilitating this necessity are power electronic converters in applications such as smart grids, renewable energy integration, and electric vehicles. Guided by the demand for improved converter topologies and conversion efficiency, much research has been conducted on varying designs, development, and control implementations. One such topology gaining significant research attention is the triple active bridge (TAB) converter. The TAB is a three-port power converter enabling both bidirectional power flow on each port and galvanic isolation for safety and …

Identifying The Job Characteristics Affecting Construction Firm Employee Turnover Intention, Seog Jae Choi

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Researchers have proved that employees who have the intention to quit the organization, called turnover intention, have decreased productivity and may not fulfill their duties properly. The turnover intention has a negative relationship with the quality of core job characteristics of the organization. As the construction industry has distinctive characteristics compared to other industries, the job characteristics that influence turnover intention need to be explored separately. This study identifies job characteristics of the construction industry that can affect turnover intention. Through the literature review, autonomy, task identity, required skill variety, task significance, justification in assigning work location, and job security …

Achieving Project Objectives And Improving Functions: The Benefits Of Ai And Construction Technologies, Fareed Salih, Islam H. El-Adaway

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The Construction Industry Is Increasingly Incorporating Artificial Intelligence (AI) And Construction Technologies Into Projects. However, It Lags Behind Other Industries In Terms Of Digital Transformation. One Of The Reasons For This Disparity Is The Lack Of Evidence-Based Information On AI And Technologies In Construction Projects. Hence, This Research Aims To Comprehensively Understand The Benefits Of AI Techniques And Construction Technologies And Their Role In Achieving Objectives And Improving Functions. To This End, The Authors Followed A Three-Step Research Methodology. Firstly, An Extensive Literature Review Was Conducted To Identify 4 AI Techniques, 13 Construction Technologies, And 28 Benefits Relevant To Their …

Minerrouter : Effective Message Routing Using Contact-Graphs And Location Prediction In Underground Mine, Abhay Goyal, Sanjay Madria, Samuel Frimpong

Computer Science Faculty Research & Creative Works

Location-based distributed communication in underground mines has been a hard problem to solve due to unreliable centralized architecture such as leaky feeder systems, high attenuation, and the unavailability of GPS signals. Delay Tolerant Networks (DTN) enable decentralized message routing using the store-carry-forward method that can help in creating situational awareness needed to handle emergency and disaster scenarios. The ability to predict where the DTN nodes (miner) might have been at/are headed to (with respect to the mine regions and pillars) at different times, combined with contact-based routing and intelligent handling of buffer, can be used for better delivery of messages. …

Characterization Of The Kansas River Alluvial Aquifer Using Towed Transient Electromagnetic Geophysical Method, Jonathon Daniel Voss

Masters Theses

"Forecasted urban development areas west of Kansas City, Kansas in the coming decades has caused an increase of research into water resources (Butler et al. 2022). A location of investigation has been the Kansas River Alluvial Aquifer (KRAA) for shallow ground water resources. To investigate the KRAA structure and grain texture, the towed transient electromagnetic system (tTEM) in conjunction with direct push electrical conductivity logs and lithology wells were used to investigate four locations between Lawrence and Manhattan, Kansas. In total, 110 line-kilometers of tTEM data was collected. The tTEM data collected were high quality and through inversions of the …

Dig Limits Optimization Using Binary Integer Linear Programming Method In Open Pit Mines, Hussam Naif Altalhi

Masters Theses

"Dig limits optimization is the process for classifying different materials (e.g., ore, stockpile material, and waste) into appropriately sized contiguous zones for open pit mining. The efficient determination of dig-limits is crucial for profitable and sustainable resource extraction in mining. Previous research has focused on defining dig-limits manually or using optimization approaches, but these methods are limited to only handling two material destinations (ore and waste). Thus, there is a need for operations research methods that consider the selectivity of mining equipment and can optimize dig-limits for metal mining operations with more than two material destinations. Consequently, the objective of …

Validation Of Athlet With Purdue University Multi-Dimensional Integral Test Assembly (Puma) Test, Emin Fatih Ozdem

Masters Theses

"Following the Three Mile Island Unit 2 (TMI-2) disaster, the development of a diagnostic system for emergency situations in a nuclear power plant was identified as an essential research area to strengthen the safety of nuclear power plants. A real-time estimation system of vital safety parameters on the main side of a PWR (Pressurized Water Reactor) facility was investigated since precise post-event scenario estimations are thought to be a crucial component of the diagnostic system. The alarm system of the plant can detect an SB-LOCA (Small Break Loss-Of-Coolant-Accident), but there were a couple of potential long-term transient occurrences. The accident …

High Strain Rate Analysis Of 3d Printed Concrete As Compared To Conventionally Cast Concrete, Weston Mcleod Thomsen

Masters Theses

"3D Printed Concrete (3DPC) is a developing method of construction that has advantages over conventional methods, including formwork reduction, complex geometry, and expedited construction. This technology has potential benefits for the military when considering the austere environments that forward operating bases are built in. This study aims to assess 3DPC applications in protective structures that protect critical assets from explosive blasts. These protective structures experience a high-strain rate response during blast loading of the structure, and the effects of this have yet to be analyzed in the literature concerning 3DPC. With the lack of prior research, the focus here will …

Fiber Assisted Re-Assembly Preformed Particle Gel For Conformance Control, Zhe Sun

Masters Theses

"In Enhanced Oil Recovery technology today, gel treatments have been implemented as a cost-effective method to improve the oil sweep efficiency in reservoirs by plugging the high permeability zones. This study presents a novel gel composition to be used in conformance control in order to improve oil recovery for mature oilfields.

The product is a fiber-assist re-assembly preformed particle gel which could be generalized to the preformed particle gels (PPG). The product developed in this study could be injected into the reservoir act as a conformance control agent by plugging water thief zones and channels in the beginning process. Due …

Investigation Of The Relationships Between Hydraulic, Physical, And Biological Soil Parameters At A Vineyard In Saint James, Missouri, Lyndsey Bennett

Masters Theses

"Soil is a living, dynamic system that performs vital functions such as crop production, organic matter decomposition, and the flow and transport of water. Given the pressures of food and in some locales water security, climate change, and sustainability, farmers, scientists, and other related specialists and stakeholders must have access to understandable soil health indicators as well as the soil hydraulic function parameters to maximize crop growth while maintaining soil health. Although biological and physical soil parameters are different, we aim to evaluate their relationship at the field scale. Hydraulic conductivity in the vadose zone may be especially important, as …

Directed Energy Deposition Processing-Performance Relationship Of Af9628, Mianqing Yang

Masters Theses

"AF9628 low alloy steel is a novel steel known for its low cost, high hardness, and outstanding tensile performance. However, the processing methods of AF9628 have been less studied in the additive manufacturing field. As the balance of hardness and tensile results is closely related to the cooling process during manufacturing process window and its relationship to resultant tensile properties is explored. By using the DED method, specimens of this steel are successfully fabricated, and tensile test results are obtained. The AF9628 steel can be manufactured for tailored properties with the DED process by controlling the cooling method. This work …

High-Pressure Infiltration Process For Additively Manufactured Ceramic Matrix Composites, Samuel Weiler

Masters Theses

"Ceramic matrix composites were developed in order to increase the fracture toughness, thermal shock resistance, and elongation of ceramic materials, while maintaining the very high temperature capabilities of these materials. A renewed focus has been placed on ceramic matrix composites due to the need for materials that maintain good mechanical strength at very high temperatures, for use in the extreme environments encountered by hypersonic vehicles, jet turbine blades, and the like. However, conventional methods to manufacture CMCs are costly and time consuming. The aim of this work is to develop a method for creating additively manufactured ceramic matrix composites using …

Low Finesse Extrinsic Fabry-Perot Interferometer (Efpi) Demodulation For High Temperature Gap Measurements, Abhishek Prakash Hungund

Masters Theses

"In continuous casting steel industries, mold flux is added to provide thermal and chemical insulation for molten steel. The mold flux absorbs detrimental inclusions from the steel and promotes uniform heat distribution to prevent sticking. To promote flux infiltration, mold oscillation is used, but this creates oscillation marks that reduce local shell growth and increase temperatures. Wide (2-3 mm) and deep (0.5-0.9 mm) oscillation marks with areas of 1.1-2.5 mm² are observed, affecting the steel quality, which results in a loss of 6% per billet to the industry. To address this challenge, we propose an extrinsic Fabry-Perot interferometer (EFPI) sensor …

Laboratory Scale Experimental Analysis Of The Effect Of Surfactants On Acid Mist Suppression During Copper Electrowinning, Thurman Kollie Elgin

Masters Theses

"The reduction in acid mist generation is an industrial occupational objective in the electrowinning industry of base metals. The technology of electrowinning as an extractive metallurgical technique of metals proficiently contributed to the recovery of pure base metals. During the process of electrowinning, oxygen bubbles are generated on the anode of the electrowinning cell because of the over potential in the cell due to high voltage. The bubbles formed tend to contain sulfuric acid of the electrolyte in the form of liquid-gas ascending particles of the solution. As these bubbles ascend to the surface of the solution, they burst at …

Processing & Properties Of Zirconium Carbide Manufactured By Ceramic On-Demand Extrusion, Clare Sabata

Masters Theses

"This research focuses on the development of a zirconium carbide (ZrC) paste for use in material extrusion direct ink write additive manufacturing (AM) followed by the pressure less densification of ZrC and the mechanical and thermal characterization of the resulting ceramics. A highly loaded, aqueous paste was developed using commercial ZrC powder ball milled to ~1 μm. Optimal dispersant, binder, and solids loading were found by rheological characterization. The paste composition consisted of 46-47 vol% ZrC, 43.5 vol% distilled water, 8.1 vol% dispersant, and 1.6 vol% binder. A yield stress of ~8 Pa allowed for shape retention upon removal of …

Microwave Materials Characterization Of Geopolymers, Jared Sinkey

Masters Theses

"The purpose of this work was to develop a process for studying geopolymer materials using a microwave materials characterization approach. Such an approach is known to provide information about chemical and physical properties of materials. As such, in this work, the focus is on the role of water in the geopolymer curing process. To do this, specimens were prepared and cast and microwave measurements conducted throughout the curing process using a short-circuited rectangular waveguide (SC-RWG) measurement technique. In this technique, the complex reflection properties/coefficient of the sample are measured. The effect of sample length and dielectric properties on materials characterization …

Investigating Accident-Tolerant Cladding In A Molten Salt-Cooled Micro-Reactor Using Multi-Physics Analysis And Uncertainty Quantification, Alexander Niles Foutch

Masters Theses

"Renewed interest in nuclear safety has resulted in development of accident-tolerant materials, such as cladding. Although developed for light water reactors, their use in more advanced reactors would save time and development costs for other new materials. This paper performed a Multiphysics investigation into the power profile, thermodynamics, heat transfer, and tensor mechanics of four candidate materials (Haynes 230, Zircaloy-4, FeCrAl, and SiC-SiC), using the highly benchmarked Kilo power design as an example of a high-temperature, highly enriched, sodium-cooled microreactor environment.

From neutronic code MCNP, no significant difference in power profile was found among the four. Using finite element software …

Discrete Event Simulation (Des) In Swapping/Charging Of Battery Electric Vehicles In Underground Mining, Albert Einstein Amponsem

Masters Theses

"With climate change concerns escalating, international agreements such as the Kyoto Protocol, the US Presidential Policy, and the Paris Agreement aim to reduce greenhouse gas (GHG) emissions, targeting significant reductions by 2050. The mining sector, a notable contributor to GHG emissions primarily through diesel-powered material haulage, emits approximately 68 million tons of CO₂ annually. Transitioning to Battery Electric Trucks (BETs) presents a viable mitigation strategy by replacing diesel trucks with electric alternatives, thus eliminating CO₂ emissions.

However, the effectiveness of BETs hinges on optimized battery swapping and charging procedures. This study employs Discrete Event Simulation (DES), a computational …

Development Of A Particulate Matter Sensor Network For Air Quality Monitoring In Indoor Settings And In Mines, Abdulrahman Bani

Masters Theses

"The importance of indoor air quality (IAQ), especially concerning particulate matter (PM), has become increasingly recognized due to its substantial impact on public health. Individuals spend a significant portion of their time indoors, where PM concentrations can exceed that of outdoors, leading to potential adverse health effects ranging from immediate irritation to long-term respiratory and cardiovascular diseases. The dynamic nature of indoor environments, combined with the diversity of PM sources, presents considerable challenges for effective IAQ monitoring and management. Traditional approaches to IAQ assessment often fall short, lacking the granularity and immediacy required to address these challenges adequately.

This abstract …

The Graduation Walk: Pareto Optimization Of Degree Paths, Arianna Gail Sy Chaves

Masters Theses

"A student’s academic history, course availability at their institution, and the overall degree of difficulty of the schedule for each semester are all critical factors in their academic success and experience. This thesis proposes an advanced recommendation algorithm that considers these real and conflicting factors that are involved in identifying a prudent degree path - a semester-by-semester course schedule to graduation - for each student. The original contribution of this work is the use of weighted-sum multi-objective constraint programming to minimize an increased number of optimization criteria and identify Pareto-optimal degree paths to be recommended to the student. The conflicting …

Evaluating Electromagnetic Interference On Gnss Receivers, Giorgi Tsintsadze

Masters Theses

"Due to high power and efficiency requirements of modern electrical drive system, inverters are utilizing fast-edge pulses as a drive signal. The high frequency pulses contain higher order harmonics can radiate electromagnetic interference above accepted levels. Modelling and understanding the mechanism that causes the radiation is studied, modelled and presented as gray-box model which contains circuit level modelling of coupling between electrical machine phase windings and low power sensor harness. The thesis consists of two main papers. In the first paper, radiated emissions from an electrical drive system is charac- terized thru gray-box modelling where coupling between electrical machine phase …