Engineering Commons^™

Formulation And Testing Of Biodegradable Polymeric Coating On Zinc Wires In Cardiovascular Stent Application, Avishan Arab Shomali

Dissertations, Master's Theses and Master's Reports

Biodegradable and biocompatible poly (L-lactic-acid) (PLLA) coating was applied on a modified zinc (Zn) substrate by dip coating, with the intent to delay the bio-corrosion and slow the degradation rate of zinc substrate. 3-(Trimethoxysilyl) propyl methacrylate (MPS) was used for modification of the zinc substrate for promoting the adhesion between the metallic substrate and the polymer coating. It is hypothesized that the delay in Zn biodegradation could be useful in the first several weeks to prevent the early loss of mechanical integrity of the endovascular stent and to improve the healing process of the diseased vascular site. The PLLA coating …

Heat Transfer Analysis In A Paddle Reactor For Biomass Fast Pyrolyis, Ankith Ullal

Dissertations, Master's Theses and Master's Reports

Heat transfer analysis was performed on a novel auger reactor for biomass fast pyrolysis. As part of this analysis, correlations for specific heat capacity and heat transfer coefficients for biomass (sawdust) and sand (used as heat transfer medium) were developed. For sand, the heat transfer coefficient followed a power law distribution with reactor fill level and temperature. For raw biomass, the heat transfer coefficient also showed similar dependence on fill level, but was independent of temperature up to 300°C. These correlations were used in a one dimensional heat transfer model developed to calculate the heating time and heating rate of …

Detecting Overpressure Zones By Using Model Based Inversion In Kupe Field, New Zealand, Timucin Cakir

Dissertations, Master's Theses and Master's Reports

Overpressure is a significant parameter during a drilling process in oil exploration. This phenomenon happens when pore pressure exceeds the limit of hydrostatic pressure in a formation and causes drastic hazards such as blow outs while drilling. This thesis focuses on the determination of possible overpressure areas and studies at three wells in Kupe Field, which is considered to be a natural-gas field in Taranaki Basin. In an effort to identify potential overpressure zones at the Kupe Field, acoustic impedance responses of 3D seismic data for three wells, along with their well log responses were evaluated.

Seismic inversion plays an …

Computational Ultrasound Elastography: A Feasibility Study, Yu Wang

Dissertations, Master's Theses and Master's Reports

Ultrasound Elastography (UE) is an emerging set of imaging modalities used to assess the biomechanical properties of soft tissues. UE has been applied to numerous clinical applications. Particularly, results from clinical trials of UE in breast lesion differentiation and staging liver fibrosis indicated that there was a lack of confidence in UE measurements or image interpretation. Confidence on UE measurements interpretation is critically important for improving the clinical utility of UE. The primary objective of my thesis is to develop a computational simulation platform based on open-source software packages including Field II, VTK, FEBio and Tetgen. The proposed virtual simulation …

Controlling Properties Of Agglomerates For Chemical Processes, Joseph A. Halt

Dissertations, Master's Theses and Master's Reports

Iron ore pellets are hard spheres made from powdered ore and binders. Pellets are used to make iron, mainly in blast furnaces. Around the time that the pelletizing process was developed, starch was proposed as a binder because it’s viscous, adheres well to iron oxides, does not contaminate pellets and is relatively cheap. In practice, however, starch leads to weak pellets with rough surfaces – these increase the amount of dust generated within process equipment and during pellet shipping and handling. Thus, even though the usual binder (bentonite clay) contaminates pellets, pelletizers prefer it to starch or other organics.

This …

Blossomsttm Hub – An Online Tool For Designing Sttm Vectors And Visualizing Phenotypic Changes Of Sttm Transgenic Lines, Avinash Subramanian

Dissertations, Master's Theses and Master's Reports

Small RNAs including microRNAs (miRNAs) and short interfering RNAs (siRNAs) are widely present in plants. They are transcribed from non-coding small RNA genes and then play as regulators to modulate the levels of messenger RNAs (mRNAs) of protein-coding genes via sequence pairings. This is because a paired complementary double sequence helix structure can trigger mRNA degradation or interfere with mRNA translation. Short Tandem Target Mimic (STTM) is a recently developed technology that can be used to produce a complementary sequence to a miRNA and destroy it or reduce the expression level of this miRNA via the formation of paired double-strand …

Position Control Of An Unmanned Aerial Vehicle From A Mobile Ground Vehicle, Astha Tiwari

Dissertations, Master's Theses and Master's Reports

Quadcopters have been developed with controls providing good maneuverability, simple mechanics, and the ability to hover, take-off and land vertically with precision. Due to their small size, they can get close to targets of interest and furthermore stay undetected at lower heights. The main drawbacks of a quadcopter are its high-power consumption and payload restriction, due to which, the number of onboard sensors is constrained. To overcome this limitation, vision-based localization techniques and remote control for the quadcopter are essential areas of current research. The core objective of this research is to develop a closed loop feedback system between an …

Surface Enabled Lab-On-A-Chip (Loc) Device For Protein Detection And Separation, Zhichao Wang

Dissertations, Master's Theses and Master's Reports

Sensitive and selective chemical/biological detection/analysis for proteins is essential for applications such as disease diagnosis, species phenotype identification, product quality control, and sample examination. Lab-on-a-chip (LOC) device provides advantages of fast analysis, reduced amount of sample requirements, and low cost, to magnificently facilitate protein detection research. Isoelectric focusing (IEF) is a strong and reliable electrophoretic technique capable of discerning proteins from complex mixtures based on the isoelectric point (pI) differences. It has experienced plenty of fruitful developments during previous decades which has given it the capability of performing with highly robust and reproducible analysis. This progress has made IEF devices …

Fea Analysis And Optimization Of Differential Housing For Fatigue Stresses And Fatigue Test Design To Study Skin Effect In Ductile Iron, Swapnil A. Pandey

Dissertations, Master's Theses and Master's Reports

Automotive emission standards are getting more stringent day by day and governments worldwide are moving to reduce emissions from automobiles. In this scenario reducing the weight of automobile components becomes an important design objective to reduce emissions. A 10% reduction of weight in the complete automobile leads to 6-8 percent improvement in mileage (Mhapankar 2015). Also, powertrain components make up for approximately 27% of the total automobile weight and thus optimizing the design of components in the powertrain is an important task (Mhapankar 2015). Statistics show that 26% of component failures in automobiles are part of powertrain and 21% of …

Research And Development Of Industrial Integrated Robotic Workcell And Robotrun Software For Academic Curriculum, Siddharth Y. Parmar

Dissertations, Master's Theses and Master's Reports

Robotic automation is consuming the laborious tasks performed by workers all over industry. The increasing demand for trained robotic engineers to implement and maintain industrial robots has led to the development of various courses in academia. Michigan Tech is a FANUC Authorized Certified Education Training Center for industrial robot training. This report discusses the research and development of an integrated robotic workcell consisting of three Fanuc robots, Allen Bradley programmable logic controller (PLC), Mini-Mover belt conveyor and Fanuc iR-vision system. The workcell allows students to explore an environment similar to industry and intended to be used for laboratory hands-on activities …

Tightening The Loop On The Circular Economy: Distributed Plastic Recycling With An Open Source Recyclebot, Shan Zhong

Dissertations, Master's Theses and Master's Reports

Following the goals of a circular economy, the growth of both plastic consumption and prosumer 3-D printing are driving an interest in producing 3-D printer filament from waste plastic. However, traditional recycling can have a significant environmental impact as it demands the collection and transportation of relatively low-density waste plastics to collection centers and reclamation facilities for separation and reconstruction. Compared to the traditional recycling, distributed recycling (where consumers directly recycle their own waste) has the potential to reduce energy consumption because it can save the energy for transportation needed in conventional recycling. A promising method of such distributed plastic …

Simulation Of Human Ankle Trajectory During Stance Phase Of Gait, Leslie Castelino

Dissertations, Master's Theses and Master's Reports

A simulation was developed which mimics the human gait characteristics based on the input of an individual’s gait trajectory. This simulation also estimates the impedance of the human ankle based on the ground reaction forces measured by the force plate. This simulation will accept alterations of the following parameters: total body weight, weight of the shank, weight of the foot, trajectories of the shank and foot of the individual and orientation of the force plate, which would generate a new gait trajectory for the ankle during the stance phase of gait. The goal of this simulation was to validate the …

An Algorithm For Reconstructing Three-Dimensional Images From Overlapping Two-Dimensional Intensity Measurements With Relaxed Camera Positioning Requirements, With Application To Additive Manufacturing, Siranee Nuchitprasitchai

Dissertations, Master's Theses and Master's Reports

Cameras are everywhere for security purposes and there are often many cameras installed close to each other to cover areas of interest, such as airport passenger terminals. These systems are often designed to have overlapping fields of view to provide different aspects of the scene to review when, for example, law enforcement issues arise. However, these cameras are rarely, if ever positioned in a way that would be conducive to conventional stereo image processing. To address this, issue an algorithm was developed to rectify images measured under such conditions, and then perform stereo image reconstruction. The initial experiments described here …

Mse Annual Report 2017, Department Of Materials Science And Engineering, Michigan Technological University

Department of Materials Science and Engineering Annual Reports

Table of Contents

• Faculty and Staff News
• Faculty Research
• Student News
• Senior Design Teams
• Graduate Student News
• Outreach
• Alumni News
• By the Numbers
• Scholarships

2016-2017 Che Newsletter, Department Of Chemical Engineering, Michigan Technological University

Department of Chemical Engineering Newsletters

Table of Contents

• Department
• Convocation
• Student News
• Faculty
• Alumni & Friends

Electrical And Computer Engineering Annual Report 2017, Department Of Electrical And Computer Engineering, Michigan Technological University

Department of Electrical and Computer Engineering Annual Reports

• Early Career Awards
• Faculty Directory
• Faculty Highlights
• Special Report: Mobility at Michigan Tech
• Faculty Publications
• Staff Profile & Directory
• Graduate Student Research
• Accelerated Master's Degree
• Graduate Student Awards & Degrees
• Undergraduate Highlights
• Senior Design
• Enterprise
• Undergraduate Student Awards & Advisory
• Grants & Contracts
• Departmental Statistics
• A Pioneer's Story

The Circuit, Spring 2017, Department Of Electrical And Computer Engineering, Michigan Technological University

Department of Electrical and Computer Engineering Newsletters

Table of Contents:

• Early Career Awards
• Spotlighting: Leonard Bohman
• Visiting Faculty
• Bridging Past and Future Through Automation
• Robotics Systems Enterprise
• Inspiring the Next Generation
• Tech Team Wins Team Tech
• Ramping Up Automotive Controls
• Bucheger Moves Senior Design Forward
• Student News
• Alumni News

Multi-Time Scale Control Of Demand Flexibility In Smart Distribution Networks, Bishnu P. Bhattarai, Kurt S. Myers, Birgitte Bak-Jensen, Sumit Paudyal

Michigan Tech Publications, Part 1

This paper presents a multi-timescale control strategy to deploy electric vehicle (EV) demand flexibility for simultaneously providing power balancing, grid congestion management, and economic benefits to participating actors. First, an EV charging problem is investigated from consumer, aggregator, and distribution system operator’s perspectives. A hierarchical control architecture (HCA) comprising scheduling, coordinative, and adaptive layers is then designed to realize their coordinative goal. This is realized by integrating multi-time scale controls that work from a day-ahead scheduling up to real-time adaptive control. The performance of the developed method is investigated with high EV penetration in a typical residential distribution grid. The …

Quantitating Active Photosystem Ii Reaction Center Content From Fluorescence Induction Transients, Cole D. Murphy, Guangyan Ni, Gang Li, Audrey Barnett, Kui Xu, Jessica Grant-Burt, Justin D. Liefer, David J. Suggett, Douglas A. Campbell

Michigan Tech Publications, Part 1

Photosystem II (PSII) is a pigment-protein complex that photochemically extracts electrons from water, generating the reductant that supports biological productivity in all biomes. Estimating the content of active PSII reaction centers in a liquid sample is a key input for estimating aquatic photosynthesis rates, as well as for analyzing phytoplankton stress responses. Established procedures for PSII content quantification based on oxygen evolution are slow, imprecise and require dense cell suspensions, and are thus inapplicable to many laboratory or field studies. A new approach uses baseline chlorophyll fluorescence emission divided by the effective absorbance cross section for PSII photochemistry, with both …

Human Centered Design Of An Open-Drum, Treadle Thresher For Quinoa Farmers In The Andes Of Northern Peru, Robert A. Hayes

Dissertations, Master's Theses and Master's Reports

Growing international demand for quinoa in recent years has led to increased production throughout its South American range, including the Peruvian Andes. Small-scale farmers, who are among the poorest Peruvians, are increasingly growing quinoa for both food security and economic benefit; however, manual harvesting activities, such as threshing, are labor-intensive and time-consuming. This report documents the design, construction and operation of prototype quinoa thresher in a rural village in Northern Peru. In addition, an overview of the history and evolutionary approach to design for the developing world is presented. From this overview, a series of criteria is considered for the …

A Host Board Design For An Experiment System Of Underwater Wireless Sensor Networks, He Huang

Dissertations, Master's Theses and Master's Reports

Evaluation of theoretical innovation in field experiments plays an important role for research in Underwater Wireless Sensor Networks (UWSNs). During the experiments, the problems of power consumption, costs, and assembly of underwater nodes concern researchers all the time. This project develops a host board for an UWSNs field experiment system. This host board solves the above problems by deploying power management module, utilizing cheap and low power consumption chips (Raspberry Pi and MSP430), and rationalizing layout.

The main functions of the host board include battery monitoring, on-board DC converters, remotely power supply control, data ports bridge, and pluggable module for …

Using Lower Extremity Muscle Activations To Estimate Human Ankle Impedance In The External-Internal Direction, Lauren N. Knop

Dissertations, Master's Theses and Master's Reports

For millions of people, mobility has been afflicted by lower limb amputation. Lower extremity prostheses have been used to improve the mobility of an amputee; however, they often require additional compensation from other joints and do not allow for natural maneuverability. To improve upon the functionality of ankle-foot prostheses, it is necessary to understand the role of different muscle activations in the modulation of mechanical impedance of a healthy human ankle. This report presents the results of using artificial neural networks (ANN) to determine the functional relationship between lower extremity electromyography (EMG) signals and ankle impedance in the transverse plane. …

The Role Of Active Flow-Control Devices In The Dynamic Aeroelastic Response Of Wind Turbine Rotors, Muraleekrishnan Menon Menon Muraleedharan Nair

Dissertations, Master's Theses and Master's Reports

The significance of wind as a renewable source of power is growing with the increasing capacity of individual utility-scale wind turbines. Contemporary wind turbines are capable of producing up to 8 MW and consequently, their rotor sizes are rapidly growing in size. This has led to an increased emphasis on studies related to improvements and innovations in load-control methodologies. Most often than not, controlling the loads on an operational turbine is a precarious scenario, especially under high wind loading. The up-scaling of turbine rotors would thus benefit from a rationale change in load control through methodologies such as variable-speed stall, …

Multi-Modal And Short-Range Transmission Loss In Ice-Covered, Near-Shore Arctic Waters, Miles B. Penhale

Dissertations, Master's Theses and Master's Reports

In the past century, extensive research has been done regarding the sound propagation in arctic ice sheets. The majority of this research has focused on low frequency propagation over long distances. One of the most commonly used excitation methods for air-ice-water layers has been explosives. However, environmental regulation has become more stringent, disallowing the use of almost all explosive excitation types. Due to changing climate conditions in these environments, new experimentation is warranted to determine sound propagation characteristics in, through, and under thin ice sheets, in shallow water, over short distances. In April, 2016 several experiments were conducted approximately 2 …

Continuous Hydrologic Modeling For Analyzing The Effects Of Drought On The Lower Colorado River In Texas, Khalid Samady

Dissertations, Master's Theses and Master's Reports

A physically based hydrologic model, the HEC-Hydrologic Modeling System (HMS), developed by the U.S. Army Corps of Engineers, has been parameterized using the Soil Moisture Accounting (SMA) algorithm, calibrated, and validated for the Lake Travis and Lake Lyndon B. Johnson (LBJ) contributing basins in central Texas. The basins are divided into a total of 15 sub-basins, and HEC-HMS with the SMA algorithm represents each sub-basin with five water storage layers involving twelve parameters--surface depression storage, canopy interception storage, upper zone soil storage, tension zone soil storage, infiltration rate, and soil percolation rate, along with storage depths, storage coefficients and percolation …

The Emission And Particulate Matter Oxidation Performance Of A Scr Catalyst On A Diesel Particulate Filter With A Downstream Scr, Sagar Sharma

Dissertations, Master's Theses and Master's Reports

Selective catalytic reduction (SCR) systems along with a NH₃ slip control catalyst (ASC) offers NOₓ conversion efficiency >90 % with NH₃ slip < 20 ppm. However, future heavy duty diesel (HDD) engines are designed for higher engine-out NOₓ to improve fuel consumption. Consequently, there is a strong desire to further improve the NOₓ reduction performance of SCR systems, to meet the 2015 California Optional Low NOₓ Standard. SCR catalysts on a diesel particulate filter provide an effective solution to reduce NOₓ and PM using a single aftertreatment device. It also provides an opportunity to increase the SCR volume to achieve NOₓ conversion efficiency >95 %. A downstream SCR catalyst substrate can be used to get additional NO_x conversion by using the SCRF^® outlet NH₃ to increase the cumulative NOₓ conversion of the system.

In this study, NOₓ reduction, NH₃ slip and PM oxidation performance of a Cu-zeolite SCRF^® with a downstream Cu-zeolite SCR were investigated based on engine experimental data at steady state conditions. The experimental data were collected at varying SCRF^® inlet temperatures, space velocities, inlet …

Air Injection As A Scour Countermeasure At Bridge Piers, Ravi Teja Reddy Tippireddy

Dissertations, Master's Theses and Master's Reports

Local scour is a major cause of concern for the stability of bridge piers and the safety of the public using the bridges. Structural countermeasures and flow-altering devices have been developed to deal with local scour. Many armoring structural countermeasures are very effective and efficient in clear water conditions but are susceptible to moving bed forms and leaching. The flow-altering devices are effective in both clear water conditions and moving bed forms, but are prone to clogging, less efficient in changing flow direction, etc. This study aims to reduce the local scour by injecting air in order to reduce the …

The Visual And Performing Arts In The Technical Communication Classroom: Reinforcing The University's Internal Community Literacy Via Service-Learning, Richard L. Ward

Dissertations, Master's Theses and Master's Reports

This report details a class taught that was an exploration into the value of STEAM or science, technology, engineering, arts, and mathematics within the confines of Technical Communication as it applies to the business and industry of theatre. It was an experiment in service learning as it could be tied into the Arts via differing technai, as described by John Wild in “Plato’s Theory of Texnh a Phenomenological Interpretation,” demonstrating a necessity for Arts as they pertain to STEM-centric universities. This report discusses a section of Technical and Professional Communication taught at Michigan technological University that consisted of twenty-five students …

Impact Of Natural Gas Direct Injection On Thermal Efficinecy In A Spark Ignition Engine, James Sevik

Dissertations, Master's Theses and Master's Reports

Interest in natural gas as an internal combustion engine fuel has been renewed due to its increasing domestic availability and stable price relative to other petroleum fuel sources. Natural gas, comprised mainly of methane, allows for up to a 25% reduction in engine out CO2 emissions due to a more favorable hydrogen-to-carbon ratio, relative to traditional petroleum sources. Traditional methods of injecting natural gas can lead to poor part-load performance, as well as a power density loss at full load due to air displacement in the intake manifold. Natural gas direct injection, which allows the fuel to be injected directly …

Techno-Economic And Life Cycle Assessments Of Biofuel Production From Woody Biomass Through Torrefaction-Fast Pyrolysis And Catalytic Upgrading, Olumide Winjobi

Dissertations, Master's Theses and Master's Reports

Biofuel production through fast pyrolysis of biomass is a promising conversion route in the production of biofuels compatible with existing technology. The bio-oil produced from fast pyrolysis is a versatile feedstock that can be used as a heating oil or upgraded to a transportation hydrocarbon biofuel. Comparative study of a one-step, fast pyrolysis only pathway and a two-step torrefaction-fast pyrolysis pathway was carried out to evaluate the effect of torrefcation on (i) the minimum selling price of biofuel and (ii) the potential life cycle GHG emissions of the biofuel production pathway.

To produce bio-oil which can serve as a substitute …