Engineering Commons^™

Biosolids-Derived Biochar For Micropollutant Removal From Wastewater, Lee Kimbell

Master's Theses (2009 -)

Trace organic compounds including antibiotics, hormones, pharmaceuticals and personal care products are discharged to the environment with liquid and solid effluent streams from water resource recovery facilities. These compounds are referred to as micropollutants, and can have negative impacts in receiving waters. Current wastewater treatment processes are not specifically designed to remove micropollutants, and many of these compounds are recalcitrant to conventional treatment technologies. Triclosan (TCS) was selected as a representative micropollutant in this study due to frequent detection in liquid effluents, residual biosolids, and surface waters. Pyrolysis - the thermochemical decomposition of organic matter at elevated temperatures in the …

Rapid In Vivo Detection Of Rat Spinal Cord Injury With Double-Diffusion-Encoded Magnetic Resonance Spectroscopy, Nathan P. Skinner, Shekar N. Kurpad, Brian D. Schmit, L. Tugan Muftuler, Matthew D. Budde

Biomedical Engineering Faculty Research and Publications

Purpose

Diffusion-weighted imaging is a common experimental tool for evaluating spinal cord injury (SCI), yet it suffers from complications that decrease its clinical effectiveness. The most commonly used technique, diffusion tensor imaging (DTI), is often confounded by effects of edema accompanying acute SCI, limiting its sensitivity to the important functional status marker of axonal integrity. The purpose of this study is to introduce a novel diffusion-acquisition method with the goal of overcoming these limitations.

Methods

A double diffusion encoding (DDE) pulse sequence was implemented with a diffusion-weighted filter orthogonal to the spinal cord for suppressing nonneural signals prior to diffusion …

An Efficient And Cost Effective Fpga Based Implementation Of The Viola-Jones Face Detection Algorithm, Peter Irgens, Curtis Bader, Theresa Lé, Devansh Saxena, Cristinel Ababei

Electrical and Computer Engineering Faculty Research and Publications

We present an field programmable gate arrays (FPGA) based implementation of the popular Viola-Jones face detection algorithm, which is an essential building block in many applications such as video surveillance and tracking. Our implementation is a complete system level hardware design described in a hardware description language and validated on the affordable DE2-115 evaluation board. Our primary objective is to study the achievable performance with a low-end FPGA chip based implementation. In addition, we release to the public domain the entire project. We hope that this will enable other researchers to easily replicate and compare their results to ours and …

Special Section On Electrical Contacts, Ronald A. Coutu Jr., Ravi Mahajan

Electrical and Computer Engineering Faculty Research and Publications

Welcome to the Special Topics Section dedicated to the 2015 Holm Conference on Electrical Contacts. This Special Section contains six high-quality papers that comprehensively describe the state of the art and potential future directions for topics of great interest to our readers. The Editor-in-Chief (EIC), in consultation with the other EICs, Associate Editors (AEs), and domain experts, selects the topics for the Special Sections, and a Guest Editor or AE (GE/AE) who is a leading expert in the technical area then directs the solicitation and peer review of the papers. In cases where the GE/AE is also an author, the …

Thz Metamaterial Characterization Using Thz-Tds, Christopher H. Kodama, Ronald A. Coutu Jr.

Electrical and Computer Engineering Faculty Research and Publications

The purpose of this chapter is to familiarize the reader with metamaterials and describe terahertz (THz) spectroscopy within metamaterials research. The introduction provides key background information on metamaterials, describes their history and their unique properties. These properties include negative refraction, backwards phase propagation, and the reversed Doppler Effect. The history and theory of metamaterials are discussed, starting with Veselago’s negative index materials work and Pendry’s publications on physical realization of metamaterials. The next sections cover measurement and analyses of THz metamaterials. THz Time-domain spectroscopy (THz-TDS) will be the key measurement tool used to describe the THz metamaterial measurement process. Sample …

Correlating Methane Production To Microbiota In Anaerobic Digesters Fed Synthetic Wastewater, Kaushik Venkiteshwaran, K. Milferstedt, M. Fujimoto, M. Johnson, Daniel Zitomer

Civil and Environmental Engineering Faculty Research and Publications

A quantitative structure activity relationship (QSAR) between relative abundance values and digester methane production rate was developed. For this, 50 triplicate anaerobic digester sets (150 total digesters) were each seeded with different methanogenic biomass samples obtained from full-scale, engineered methanogenic systems. Although all digesters were operated identically for at least 5 solids retention times (SRTs), their quasi steady-state function varied significantly, with average daily methane production rates ranging from 0.09 ± 0.004 to 1 ± 0.05 L-CH₄/L_R-day (L_R = Liter of reactor volume) (average ± standard deviation). Digester microbial community structure was analyzed using more …

Image-Based Multi-Target Tracking Through Multi-Bernoulli Filtering With Interactive Likelihoods, Anthony B. Hoak, Henry P. Medeiros, Richard J. Povinelli

Electrical and Computer Engineering Faculty Research and Publications

We develop an interactive likelihood (ILH) for sequential Monte Carlo (SMC) methods for image-based multiple target tracking applications. The purpose of the ILH is to improve tracking accuracy by reducing the need for data association. In addition, we integrate a recently developed deep neural network for pedestrian detection along with the ILH with a multi-Bernoulli filter. We evaluate the performance of the multi-Bernoulli filter with the ILH and the pedestrian detector in a number of publicly available datasets (2003 PETS INMOVE, Australian Rules Football League (AFL) and TUD-Stadtmitte) using standard, well-known multi-target tracking metrics (optimal sub-pattern assignment (OSPA) and classification …

Evaluation Of Whole-Brain Resting-State Functional Connectivity In Spinal Cord Injury - A Large-Scale Network Analysis Using Network Based Statistic, Mayank Kaushal, Akinwunmi Oni-Orisan, Gang Chen, Wenjun Li, Jack Leschke, B. Douglas Ward, Benjamin Kalinosky, Matthew D. Budde, Brian D. Schmit, Shi-Jiang Li, Viashnavi Muqeet, Shekar N. Kurpad

Biomedical Engineering Faculty Research and Publications

Large-scale network analysis characterizes the brain as a complex network of nodes and edges to evaluate functional connectivity patterns. The utility of graph-based techniques has been demonstrated in an increasing number of restingstate functional MRI (rs-fMRI) studies in the normal and diseased brain. However, to our knowledge, graph theory has not been used to study the reorganization pattern of resting-state brain networks in patients with traumatic complete spinal cord injury (SCI). In the present analysis, we applied a graph-theoretical approach to explore changes to global brain network architecture as a result of SCI. Fifteen subjects with chronic (> 2 years) …

A Fault-Tolerant T-Type Multilevel Inverter Topology With Increased Overload Capability And Soft-Switching Characteristics, Jiangbiao He, Ramin Katebi, Nathan Weise, Nabeel Demerdash, Lixiang Wei

Electrical and Computer Engineering Faculty Research and Publications

he performance of a novel three-phase four-leg fault-tolerant T-type inverter topology is introduced in this paper. This inverter topology provides a fault-tolerant solution to any open-circuit and certain short-circuit switching faults in the power devices. During any of the fault-tolerant operation modes for these device faults, there is no derating required in the inverter output voltage or output power. In addition, overload capability is increased in this new T-type inverter compared to that in the conventional three-level T-type inverter. Such increase in inverter overload capability is due to the utilization of the redundant leg for overload current sharing with other …

The Effect Of Plant Water Storage On Water Fluxes Within The Coupled Soil–Plant System, Cheng-Wei Huang, Jean-Christopher Domec, Eric J. Ward, Tomer Duman, Gabriele Manolia, Anthony J. Parolari, Gabriel Katul

Civil and Environmental Engineering Faculty Research and Publications

In addition to buffering plants from water stress during severe droughts, plant water storage (PWS) alters many features of the spatio-temporal dynamics of water movement in the soil–plant system. How PWS impacts water dynamics and drought resilience is explored using a multi-layer porous media model.

Spatio-Temporal Patterning In Primary Motor Cortex At Movement Onset, Matthew D. Best, Aaron J. Suminski, Kazutaka Takahashi, Kevin A. Brown, Nicholas G. Hatsopoulos

Biomedical Engineering Faculty Research and Publications

Voluntary movement initiation involves the engagement of large populations of motor cortical neurons around movement onset. Despite knowledge of the temporal dynamics that lead to movement, the spatial structure of these dynamics across the cortical surface remains unknown. In data from 4 rhesus macaques, we show that the timing of attenuation of beta frequency local field potential oscillations, a correlate of locally activated cortex, forms a spatial gradient across primary motor cortex (MI). We show that these spatio-temporal dynamics are recapitulated in the engagement order of ensembles of MI neurons. We demonstrate that these patterns are unique to movement onset …

Developing A Low-Cost Force Treadmill Via Dynamic Modeling, Chih-Yuan Hong, Lan-Yuen Guo, Rong Song, Mark L. Nagurka, Jia-Li Sung, Chen-Wen Yen

Mechanical Engineering Faculty Research and Publications

By incorporating force transducers into treadmills, force platform-instrumented treadmills (commonly called force treadmills) can collect large amounts of gait data and enable the ground reaction force (GRF) to be calculated. However, the high cost of force treadmills has limited their adoption. This paper proposes a low-cost force treadmill system with force sensors installed underneath a standard exercise treadmill. It identifies and compensates for the force transmission dynamics from the actual GRF applied on the treadmill track surface to the force transmitted to the force sensors underneath the treadmill body. This study also proposes a testing procedure to assess the GRF …

Fate And Impacts Of Triclosan, Sulfamethoxazole, And 17Β-Estradiol During Nutrient Recovery Via Ion Exchange And Struvite Precipitation, Yiran Tong, Patrick J. Mcnamara, Brooke K. Mayer

Civil and Environmental Engineering Faculty Research and Publications

Increasing emphasis on resource recovery from wastewater highlights the importance of capturing valuable products, e.g., nutrients such as nitrogen and phosphorus, while removing contaminants, e.g., organic micropollutants. The objective of this research was to evaluate the fate of the micropollutants triclosan (present as a mixture of neutral and anionic species at neutral pH), 17β-estradiol (neutral at neutral pH), and sulfamethoxazole (anionic at neutral pH) during nutrient recovery using ion exchange-precipitation. Adsorption of the three micropollutants to the phosphate-selective ion exchange resins LayneRT and DOW-HFO-Cu ranged from 54% to 88% in Milli-Q water tests and 50% to 71% in …

Curriculum Innovation: Incorporating The Kern Engineering Entrepreneurial Network (Keen) Framework Into Online Discussions, Lisa Bosman, Brooke K. Mayer, Patrick J. Mcnamara

Civil and Environmental Engineering Faculty Research and Publications

The purpose of this study was to respond to the following research question: How does the Kern Engineering Entrepreneurial Network (KEEN) framework build interest in technical topic areas, impact student learning outcomes, and develop the entrepreneurial mindset when applied to the engineering classroom? The KEEN framework was developed to combine the entrepreneurial mindset with engineering education to produce a more valuable, strategically prepared engineer, rather than simply an “obedient engineer”. The framework proposes that the entrepreneurial mindset of students is increased by promoting curiosity, encouraging connections, and creating value. The results from this work provide insight into the impact and …

Virtual Reality Of Earthquake Ground Motions For Emergency Response, Ting Lin

Civil and Environmental Engineering Faculty Research and Publications

Ground motions interface earthquake science and engineering to advance understanding of seismic hazards and risk. Virtual reality provides an attractive tool to extend knowledge of the research community to a larger audience. This work visualizes emergency response under extreme motions, in the CAVE of the MARquette Visualization Laboratory. The visualization (a) displays ground motions (from the science community), (b) inputs these motions to structural models (from the engineering community) and illustrates the resulting responses, (c) translates structural responses to damage states of building elements, (d) creates a virtual room subjected to the perception associated with such earthquake shaking, and (e) …

Editorial" Fibre Reinforced Polymer Composites For Structural Applications In Construction, Jun Deng, Marcus M.K. Lee, Baolin Wan, Giuseppina Amato

Civil and Environmental Engineering Faculty Research and Publications

No abstract provided.

Baseline Rolling Resistance For Tires’ On-Road Fuel Efficiency Using Finite Element Modeling, Jaime Hernandez, Imad L. Al-Qadi, Hasan Ozer

Civil and Environmental Engineering Faculty Research and Publications

Calculation of truck tires rolling resistance, using the finite element method and considering variables such as incompressible visco-hyperelastic rubber materials, accurate tire geometry and steady temperature distribution, is presented. The model was validated using experimentally measured contact area and contact stresses. Rolling resistance was calculated for three values of axle load, tire inflation pressure, temperature and speed. In addition, regression analysis was used to propose a mathematical expression for predicting rolling resistance as a function of the considered variables. Finally, the contribution of tire’s rubber components to the internal energy was quantified, and it was found that sidewall and subtread …

Limb Stabilization In Older Adults And Chronic Stroke Survivors: A Pilot Study, Raymond C. Doudlah, Robert A. Scheidt, Aaron J. Suminski

Biomedical Engineering Faculty Research and Publications

Visual fidelity influences many aspects of daily living, including stabilizing wrist movements against environmental perturbations. Here, we present a pilot investigation to determine how visual feedback impacts wrist stabilization for populations with age related declines in motor function and chronic stroke. To quantify these interactions, behavioral performance and local brain activation were observed during a task requiring stabilization of the wrist against constant and stochastic extensor torque perturbations. All subjects were better able to stabilize their wrist when veridical visual feedback of their limb was provided. Examination of the neural activation maps in the Control and Aging populations revealed patterns …

Lung Injury Pathways: Adenosine Receptor 2b Signaling Limits Development Of Ischemic Bronchiolitis Obliterans Organizing Pneumonia, John C. Densmore, Terry R. Schaid, Paul M. Jeziorczak, Meetha Medhora, Said H. Audi, Shraddha Nayak, John Auchampach, Melinda R. Dwinell, Aron M. Geurts, Elizabeth R. Jacobs

Biomedical Engineering Faculty Research and Publications

Purpose/Aim of the Study: Adenosine signaling was studied in bronchiolitis obliterans organizing pneumonia (BOOP) resulting from unilateral lung ischemia. Materials and Methods: Ischemia was achieved by either left main pulmonary artery or complete hilar ligation. Sprague–Dawley (SD) rats, Dahl salt sensitive (SS) rats and SS mutant rat strains containing a mutation in the A_2B adenosine receptor gene (Adora2b) were studied. Adenosine concentrations were measured in bronchoalveolar lavage (BAL) by HPLC. A_2A (A_2AAR) and A_2B adenosine receptor (A_2BAR) mRNA and protein were quantified. Results: Twenty-four hours after unilateral PA …

Autocatalytic Pyrolysis Of Wastewater Biosolids For Product Upgrading, Zhongzhe Liu, Patrick J. Mcnamara, Daniel Zitomer

Civil and Environmental Engineering Faculty Research and Publications

The main goals for sustainable water resource recovery include maximizing energy generation, minimizing adverse environmental impacts, and recovering beneficial resources. Wastewater biosolids pyrolysis is a promising technology that could help facilities reach these goals because it produces biochar that is a valuable soil amendment as well as bio-oil and pyrolysis gas (py-gas) that can be used for energy. The raw bio-oil, however, is corrosive; therefore, employing it as fuel is challenging using standard equipment. A novel pyrolysis process using wastewater biosolids-derived biochar (WB-biochar) as a catalyst was investigated to decrease bio-oil and increase py-gas yield for easier energy recovery. WB-biochar …

Tire-Pavement Interaction Modeling: Hyperelastic Tire And Elastic Pavement, Jaime Hernandez, Imad L. Al-Qadi

Civil and Environmental Engineering Faculty Research and Publications

The interaction between deformable tire and pavement was studied using the validated finite element model; the full understanding of tire–pavement contact has implications for pavement damage prediction and pavement life-cycle assessment (fuel consumption estimation). The tire’s rubber and reinforcement were considered hyperelastic and linear elastic, respectively, with material constants obtained from the tire manufacturer (rubber) and laboratory testing (reinforcement). On the other hand, the pavement was assumed linear elastic supported by linear elastic springs. This assumption was made as a first step to examine the impact of using a deformable-on-deformable tire–pavement system to predict energy in the tire and contact …

Diffusion Tensor Imaging Correlates With Short-Term Myelopathy Outcome In Patients With Cervical Spondylotic Myelopathy, Aditya Vedantam, Avinash Rao, Shekar N. Kurpad, Michael B. Jirjis, Gerald Eckardt, Brian D. Schmit, Marjorie C. Wang

Biomedical Engineering Faculty Research and Publications

Objective

To determine if spinal cord diffusion tensor imaging indexes correlate with short-term clinical outcome in patients undergoing elective cervical spine surgery for cervical spondylotic myelopathy (CSM).

Methods

A prospective consecutive cohort study was performed in patients undergoing elective cervical spine surgery for CSM. After obtaining informed consent, patients with CSM underwent preoperative T2-weighted magnetic resonance imaging and diffusion tensor imaging of the cervical spine. Fractional anisotropy (FA) values at the level of maximum cord compression and at the noncompressed C1-2 level were calculated on axial images. We recorded the modified Japanese Orthopaedic Association (mJOA) scale, Neck Disability Index, and …

Smartphone Based Optical Spectrometer For Diffusive Reflectance Spectroscopic Measurement Of Hemoglobin, Perry Edwards, Chenji Zhang, Baigang Zhang, Xiangqian Hong, Vivek K. Nagarajan, Bing Yu, Zhiwen Liu

Biomedical Engineering Faculty Research and Publications

We report a miniature, visible to near infrared G-Fresnel spectrometer that contains a complete spectrograph system, including the detection hardware and connects with a smartphone through a microUSB port for operational control. The smartphone spectrometer is able to achieve a resolution of ~5 nm in a wavelength range from 400 nm to 1000 nm. We further developed a diffuse reflectance spectroscopy system using the smartphone spectrometer and demonstrated the capability of hemoglobin measurement. Proof of concept studies of tissue phantoms yielded a mean error of 9.2% on hemoglobin concentration measurement, comparable to that obtained with a commercial benchtop spectrometer. The …

Lessons Learned From A 10-Year Collaboration Between Biomedical Engineering And Industrial Design Students In Capstone Design Projects, Jay R. Goldberg, Pascal Malassigné

Biomedical Engineering Faculty Research and Publications

Engineers and industrial designers have different approaches to problem solving. Both place heavy emphasis on identification of customer needs, manufacturing methods, and prototyping. Industrial designers focus on aesthetics, ergonomics, ease of use, manufacturing methods, and the user’s experience. They tend to be more visual and more concerned with the interaction between users and products. Engineers focus on functionality, performance requirements, analytical modeling, and design verification and validation. They tend to be more analytical and more concerned with the design of internal components and product performance. Engineers and industrial designers often work together on project teams in industry. Collaboration between the …

Structurofunctional Resting-State Networks Correlate With Motor Function In Chronic Stroke, Benjamin Kalinosky, Reivian B. Barillas, Brian D. Schmit

Biomedical Engineering Faculty Research and Publications

Purpose

Motor function and recovery after stroke likely rely directly on the residual anatomical connections in the brain and its resting-state functional connectivity. Both structural and functional properties of cortical networks after stroke are revealed using multimodal magnetic resonance imaging(MRI). Specifically, functional connectivity MRI (fcMRI) can extract functional networks of the brain at rest, while structural connectivity can be estimated from white matter fiber orientations measured with high angular-resolutiondiffusion imaging (HARDI). A model that marries these two techniques may be the key to understanding functional recovery after stroke. In this study, a novel set of voxel-level measures …

How A Diverse Research Ecosystem Has Generated New Rehabilitation Technologies: Review Of Nidilrr’S Rehabilitation Engineering Research Centers, David J. Reinkensmeyer, Sarah Blackstone, Cathy Bodine, John Brabyn, David Brienza, Kevin Caves, Frank Deruyter, Edmund Durfee, Stefania Fatone, Geoff Fernie, Steven Gard, Patricia Karg, Todd A. Kuiken, Gerald F. Harris, Mike Jones, Yue Li, Jordana Maisel, Michael Mccue, Michelle A. Meade, Helena Mitchell, Tracy L. Mitzner, James L. Patton, Philip S. Requejo, James H. Rimmer, Wendy A. Rogers, W. Zev Rymer, Jon A. Sanford, Lawrence Schneider, Levin Sliker, Stephen Sprigle, Aaron Steinfeld, Edward Steinfeld, Gregg Vanderheiden, Carolee Winstein, Li-Qun Zhang, Thomas Corfman

Biomedical Engineering Faculty Research and Publications

Over 50 million United States citizens (1 in 6 people in the US) have a developmental, acquired, or degenerative disability. The average US citizen can expect to live 20% of his or her life with a disability. Rehabilitation technologies play a major role in improving the quality of life for people with a disability, yet widespread and highly challenging needs remain. Within the US, a major effort aimed at the creation and evaluation of rehabilitation technology has been the Rehabilitation Engineering Research Centers (RERCs) sponsored by the National Institute on Disability, Independent Living, and Rehabilitation Research. As envisioned at their …

Detection Theory For Accurate And Non-Invasive Skin Cancer Diagnosis Using Dynamic Thermal Imaging, Sebastian E. Godoy, Majeed M. Hayat, David A. Ramirez, Stephen A. Myers, R. Steven Padilla, Sanjay Krishna

Electrical and Computer Engineering Faculty Research and Publications

Skin cancer is the most common cancer in the United States with over 3.5M annual cases. Presently, visual inspection by a dermatologist has good sensitivity (> 90%) but poor specificity (< 10%), especially for melanoma, which leads to a high number of unnecessary biopsies. Here we use dynamic thermal imaging (DTI) to demonstrate a rapid, accurate and non-invasive imaging system for detection of skin cancer. In DTI, the lesion is cooled down and the thermal recovery is recorded using infrared imaging. The thermal recovery curves of the suspected lesions are then utilized in the context of continuous-time detection theory in order to define an optimal statistical decision rule such that the sensitivity of the algorithm is guaranteed to be at a maximum for every prescribed false-alarm probability. The proposed methodology was tested in a pilot study including 140 human subjects demonstrating a sensitivity in excess of 99% for a prescribed specificity in excess of 99% for detection of skin cancer. To the best of our knowledge, this is the highest reported accuracy for any non-invasive skin cancer diagnosis method.

Evaluating Outer Segment Length As A Surrogate Measure Of Peak Foveal Cone Density, Melissa A. Wilk, Brandon M. Wilk, Christopher S. Langlo, Robert F. Cooper, Joseph Carroll

Biomedical Engineering Faculty Research and Publications

Adaptive optics (AO) imaging tools enable direct visualization of the cone photoreceptor mosaic, which facilitates quantitative measurements such as cone density. However, in many individuals, low image quality or excessive eye movements precludes making such measures. As foveal cone specialization is associated with both increased density and outer segment (OS) elongation, we sought to examine whether OS length could be used as a surrogate measure of foveal cone density. The retinas of 43 subjects (23 normal and 20 albinism; aged 6–67 years) were examined. Peak foveal cone density was measured using confocal adaptive optics scanning light ophthalmoscopy (AOSLO), and OS …

Cmos Approach To Compressed-Domain Image Acquisition, Javad Ghasemi, Manish Bhattarai, Glauco R.C. Fiorante, Payman Zarkesh-Ha, Sanjay Krishna, Majeed M. Hayat

Electrical and Computer Engineering Faculty Research and Publications

A hardware implementation of a real-time compressed-domain image acquisition system is demonstrated. The system performs front-end computational imaging, whereby the inner product between an image and an arbitrarily-specified mask is implemented in silicon. The acquisition system is based on an intelligent readout integrated circuit (iROIC) that is capable of providing independent bias voltages to individual detectors, which enables implementation of spatial multiplication with any prescribed mask through a bias-controlled response-modulation mechanism. The modulated pixels are summed up in the image grabber to generate the compressed samples, namely aperture-coded coefficients, of an image. A rigorous bias-selection algorithm is presented to the …

Optimization Of Patch Antennas Via Multithreaded Simulated Annealing Based Design Exploration, James E. Richie, Cristinel Ababei

Electrical and Computer Engineering Faculty Research and Publications

In this paper, we present a new software framework for the optimization of the design of microstrip patch antennas. The proposed simulation and optimization framework implements a simulated annealing algorithm to perform design space exploration in order to identify the optimal patch antenna design. During each iteration of the optimization loop, we employ the popular MEEP simulation tool to evaluate explored design solutions. To speed up the design space exploration, the software framework is developed to run multiple MEEP simulations concurrently. This is achieved using multithreading to implement a manager-workers execution strategy. The number of worker threads is the same …