Engineering Commons^™

Leaching Of A Mongolian Chalcopyrite Concentrate, Nicholas J. Welham, Jadambaa Temuujin, Nader Setoudeh

Research outputs 2014 to 2021

A Mongolian chalcopyrite flotation concentrate was leached using sodium hypochlorite adjusted to different pH using hydrochloric acid. It was found that using a starting pH of below 5.0 resulted in more efficient leaching. The extent of chalcopyrite leaching was determined by the concentration of sodium hypochlorite with > 40% dissolution being achieved. The residue after leaching was found to consist primarily of unreacted chalcopyrite which would be suitable for further leaching or smelting.

A Review Of Latest Developments, Progress, And Applications Of Heat Pipe Solar Collectors, Abdellah Sharifian, Mehdi Khiadani, Ataollah Nosrati

Research outputs 2014 to 2021

Among all the available solutions to the current high energy demand and consequent economic and environmental problems, solar energy, without any doubt, is one of the most promising and widespread solutions. However, conventional solar systems face some intractable challenges affecting their technical performance and economic feasibility. To overcome these challenges, increasing attention has been drawn towards the utilization of heat pipes, as an efficient heat transfer technology, in conventional solar systems. To the authors’ knowledge, despite many valuable studies on heat pipe solar collectors (mainly during the last decade), a comprehensive review which surveys and summarizes those studies and identifies …

Application Of 3d Delaunay Triangulation In Fingerprint Authentication System, Wencheng Yang, Ahmed Ibrahim, Junaid Chaudhry, Song Wang, Jiankun Hu, Craig Valli

Research outputs 2014 to 2021

Biometric security has found many applications in Internet of Things (IoT) security. Many mobile devices including smart phones have supplied fingerprint authentication function. However, the authentication performance in such restricted environment has been downgraded significantly. A number of methods based on Delaunay triangulation have been proposed for minutiae-based fingerprint matching, due to some favorable properties of the Delaunay triangulation under image distortion. However, all existing methods are based on 2D pattern, of which each unit, a Delaunay triangle, can only provide limited discrimination ability and could cause low matching performance. In this paper, we propose a 3D Delaunay triangulation based …

Extraction Of Patterns In Selected Network Traffic For A Precise And Efficient Intrusion Detection Approach, Priya Naran Rabadia

Theses: Doctorates and Masters

This thesis investigates a precise and efficient pattern-based intrusion detection approach by extracting patterns from sequential adversarial commands. As organisations are further placing assets within the cyber domain, mitigating the potential exposure of these assets is becoming increasingly imperative. Machine learning is the application of learning algorithms to extract knowledge from data to determine patterns between data points and make predictions. Machine learning algorithms have been used to extract patterns from sequences of commands to precisely and efficiently detect adversaries using the Secure Shell (SSH) protocol. Seeing as SSH is one of the most predominant methods of accessing systems it …

Bowel Sounds Identification And Migrating Motor Complex Detection With Low-Cost Piezoelectric Acoustic Sensing Device, Xuhao Du, Gary Allwood, Katherine Mary Webberley, Adam Osseiran, Barry J. Marshall

Research outputs 2014 to 2021

Interpretation of bowel sounds (BS) provides a convenient and non-invasive technique to aid in the diagnosis of gastrointestinal (GI) conditions. However, the approach’s potential is limited by variation between BS and their irregular occurrence. A short, manual auscultation is sufficient to aid in diagnosis of only a few conditions. A longer recording has the potential to unlock additional understanding of GI physiology and clinical utility. In this paper, a low-cost and straightforward piezoelectric acoustic sensing device was designed and used for long BS recordings. The migrating motor complex (MMC) cycle was detected using this device and the sound index as …

Review Of Deep Learning Methods In Robotic Grasp Detection, Shehan Caldera, Alexander Rassau, Douglas Chai

Research outputs 2014 to 2021

For robots to attain more general-purpose utility, grasping is a necessary skill to master. Such general-purpose robots may use their perception abilities to visually identify grasps for a given object. A grasp describes how a robotic end-effector can be arranged to securely grab an object and successfully lift it without slippage. Traditionally, grasp detection requires expert human knowledge to analytically form the task-specific algorithm, but this is an arduous and time-consuming approach. During the last five years, deep learning methods have enabled significant advancements in robotic vision, natural language processing, and automated driving applications. The successful results of these methods …

Influence Of Substrate Stage Temperature And Rotation Rate On The Magneto-Optical Quality Of Rf-Sputtered Bi2.1dy0.9fe3.9ga1.1o12 Garnet Thin Films, Mohammad E. Alam, Mikhail Vasiliev, Kamal Alameh

Research outputs 2014 to 2021

Highly bismuth-substituted iron garnet thin films are prepared on quartz substrates by using a radio frequency (RF) magnetron sputtering technique. We study the factors (process parameters associated with the RF magnetron sputter deposition technique) affecting the magneto-optical (MO) properties of ferrite garnet films of composition Bi2.1Dy0.9Fe3.9Ga1.1O12. All films show high MO response across the visible range of wavelengths after being annealed. In particular, the effects of substrate stage temperature and rotation rate on the various properties of films are studied. Experimental results reveal that the characteristics of garnet films of this type can be tuned and optimized for use in …

Near-Net Forming Complex Shaped Zr-Based Bulk Metallic Glasses By High Pressure Die Casting, Lehua Liu, Tao Zhang, Zhiyuan Liu, Chunyan Yu, Xixi Dong, Liangju He, Kuan Gao, Xuguang Zhu, Wenhao Li, Chengyong Wang, Peijie Li, Laichang Zhang, Lugee Li

Research outputs 2014 to 2021

Forming complex geometries using the casting process is a big challenge for bulk metallic glasses (BMGs), because of a lack of time of the window for shaping under the required high cooling rate. In this work, we open an approach named the “entire process vacuum high pressure die casting” (EPV-HPDC), which delivers the ability to fill die with molten metal in milliseconds, and create solidification under high pressure. Based on this process, various Zr-based BMGs were prepared by using industrial grade raw material. The results indicate that the EPV-HPDC process is feasible to produce a glassy structure for most Zr-based …

Stability Analysis And Design Charts For A Sandy Soil Slope Supporting An Embedded Strip Footing, Emmanuel Baah-Frempong, Sanjay Kumar Shukla

Research outputs 2014 to 2021

In several field situations, especially in the hilly terrains, the construction of footings on slopes becomes essential. The factor of safety of a slope supporting a loaded footing on the crest is dependent on the position of the footing from the crest edge. Most studies in the past have focused on analysing the bearing capacity and settlement behaviour of a footing resting on a slope crest, but foundations in most infrastructure projects are usually built at some depth below the ground surface. Therefore, the availability of some form of design charts for determining the factor of safety of a slope …

Ultrafast Consolidation Of Bulk Nanocrystalline Titanium Alloy Through Ultrasonic Vibration, Peng Chen, W. B. Liao, Lehua Liu, F Luo, Xiaoyu Wu, Peijie Li, C Yang, M Yan, Y. J. Liu, Laichang Zhang, Zhiyuan Liu

Research outputs 2014 to 2021

Nanocrystalline (NC) materials have fascinating physical and chemical properties, thereby they exhibit great prospects in academic and industrial fields. Highly efficient approaches for fabricating bulk NC materials have been pursued extensively over past decades. However, the instability of nanograin, which is sensitive to processing parameters (such as temperature and time), is always a challenging issue to be solved and remains to date. Herein, we report an ultrafast nanostructuring strategy, namely ultrasonic vibration consolidation (UVC). The strategy utilizes internal friction heat, generated from mutually rubbing between Ti-based metallic glass powders, to heat the glassy alloy rapidly through its supercooled liquid regime, …

Homogenization And Growth Behavior Of Second-Phase Particles In A Deformed Zr-Sn-Nb-Fe-Cu-Si-O Alloy, Liang-Yu Chen, Peng Sang, Lina Zhang, Dongpo Song, Yanqiu Chu, Linjiang Chai, Laichang Zhang

Research outputs 2014 to 2021

Homogeneous distribution of fine second-phase particles (SPPs) fabricated by cycles of deformation and annealing in zirconium alloys is a critical consideration for the corrosion resistance of fuel claddings. Different deformation degrees of zirconium alloys would result in distinctive microstructures, leading to a distinct growth of SPPs during subsequent annealing. Unfortunately, the homogenization and growth behavior of SPPs in deformed zirconium alloys have not been well studied. In this work, a β-quenched Zr–Sn–Nb–Fe–Cu–Si–O alloy was rolled and annealed at 580◦C or 680◦C. The morphologies, distributions, and sizes of SPPs resulting from the different processing procedures were investigated. A linear distribution of …

Improved Deformation Behavior In Ti-Zr-Fe-Mn Alloys Comprising The C14 Type Laves And Β Phases, Chirag D. Rabadia, Y. J. Liu, Syed F. Jawed, L. Wang, Y. H. Li, X. H. Zhang, T. B. Sercombe, Hongqi Sun, Laichang Zhang

Research outputs 2014 to 2021

Laves phase alloys are promising materials for several structural applications, but the extreme brittleness is the predominant shortcoming of a Laves matrix. One potential solution to overcome this shortcoming is to alloy Laves matrix with some soft matrix. A group of Ti-35Zr-5Fe-xMn (x = 0, 2, 4, 6, 8 wt%) alloys was cast with an aim to improve deformation in Laves alloy compositions. The phase and microstructure analyses reveal dual phase matrices, including a β phase and a C14 type Laves phase in the investigated alloys. The mechanical properties such as yield strength, hardness and plastic strain for the investigated …

A Security Review Of Local Government Using Nist Csf: A Case Study, Ahmed Ibrahim, Craig Valli, Ian Mcateer, Junaid Chaudhry

Research outputs 2014 to 2021

Evaluating cyber security risk is a challenging task regardless of an organisation’s nature of business or size, however, an essential activity. This paper uses the National Institute of Standards and Technology (NIST) cyber security framework (CSF) to assess the cyber security posture of a local government organisation in Western Australia. Our approach enabled the quantification of risks for specific NIST CSF core functions and respective categories and allowed making recommendations to address the gaps discovered to attain the desired level of compliance. This has led the organisation to strategically target areas related to their people, processes, and technologies, thus mitigating …

An Integrated System To Design Machine Layouts For Modular Special Purpose Machines, Uday Hameed Farhan

Theses: Doctorates and Masters

This thesis introduces the development of an integrated system for the design of layouts for special purpose machines (SPMs). SPMs are capable of performing several machining operations (such as drilling, milling, and tapping) at the same time. They consist of elements that can be arranged in different layouts. Whilst this is a unique feature that makes SPMs modular, a high level of knowledge and experience is required to rearrange the SPM elements in different configurations, and also to select appropriate SPM elements when product demand changes and new layouts are required. In this research, an integrated system for SPM layout …

Using Agricultural Wastes To Treat Lead-Contaminated Water In Western Australia, Hanie Hashtroudi

Theses: Doctorates and Masters

Aqueous solutions are becoming increasingly contaminated in all parts of the world (2015). Heavy metals are toxic contaminants that are mainly distributed in urban stormwater run-off and industrial wastewaters as a result of some mining operations, electronic assembly planting, battery manufacturing, and etching operations (Kadirvelu et al. 2001). Pb (II) is a heavy metal that causes significant damage in the human body. Drinking lead-contaminated water even at low concentrations may cause lifethreatening conditions such as cancer, kidney damage, brain damage, and liver problems (El-Said 2010). Therefore, it is necessary to remove lead from aqueous solutions.

Several conventional physical, chemical, and …

Development, Manufacture And Application Of A Solid-State Ph Sensor Using Ruthenium Oxide, Wade Lonsdale

Theses: Doctorates and Masters

The measurement of pH is undertaken frequently in numerous settings for many applications. The common glass pH probe is almost ideal for measuring pH, and as such, it is used almost ubiquitously. However, glass is not ideal for all applications due to its relatively large size, fragility, need for recalibration and wet-storage. Therefore, much research has been undertaken on the use of metal oxides as an alternative for the measurement of pH.

Here, a solid-state potentiometric pH sensor is developed using ruthenium metal oxide (RuO2). Initially, pH sensitive RuO2 electrodes were prepared by deposition with radio frequency magnetron sputtering (RFMS) …

Liner Characterisation And Leak Detection Using Electrical Resistivity Techniques, Lopa M S Pandey

Theses: Doctorates and Masters

The resistivity of soil ranges from 7-15 Ωm for Leachate #1 to 20-50 Ωm for Leachate #2. The resistivity decreases with an increase in the proximity to the leak point. Furthermore, the resistivity values obtained with water were nearly 10 times the values observed with landfill leachate as the leaching liquid. Based on the resistivity profiles of soil as observed at different time intervals, the method is found to be effective in determining leakages in the liner.

The test results have also been presented for the leakage of Bayer liquor obtained from aluminium manufacturing company in Western Australia. The resistivity …

Evaluation Of Bio-Asphalt Binders Modified With Biochar: A Pyrolysis By-Product Of Mesua Ferrea Seed Cover Waste, Abhinay Kumar, Rajan Choudhary, Rumi Narzari, Rupam Kataki, Sanjay K. Shukla

Research outputs 2014 to 2021

With growing global concerns related to energy security and sustainability, interest in bio-fuels has increased significantly. Production of biofuel mostly begins with pyrolysis, a process that converts the biomass to liquid biooil, solid biochar and gases. A large amount of carbonaceous biochar is generated as a by-product during the pyrolysis. However, no major effort has been made in the past decade to utilize the biochar in pavement applications, especially as a bio-modifier to asphalt binders. In this study, an attempt was made to evaluate the carbonaceous biochar, obtained during bio-fuel production through pyrolysis of Mesua ferrea seed cover waste, as …

Automated Optical Mark Recognition Scoring System For Multiple-Choice Questions, Murtadha Alomran

Theses: Doctorates and Masters

Multiple-choice questions are one of the questions commonly used in assessments. It is widely used because this type of examination can be an effective and reliable way to examine the level of student’s knowledge. So far, this type of examination can either be marked by hand or with specialised answer sheets and scanning equipment. There are specialised answer sheets and scanning equipment to mark multiple-choice questions automatically. However, these are expensive, specialised and restrictive answer sheets and optical mark recognition scanners.

This research aims to design and implement a multiple-choice answer sheet and a reliable image processing-based scoring system that …

Optimisation Of Stand-Alone Hybrid Energy Systems For Power And Thermal Loads, Barun Kumar Das

Theses: Doctorates and Masters

Stand-alone hybrid energy systems are an attractive option for remote communities without a connection to a main power grid. However, the intermittent nature of solar and other renewable sources adversely affects the reliability with which these systems respond to load demands. Hybridisation, achieved by combining renewables with combustion-based supplementary prime movers, improves the ability to meet electric load requirements. In addition, the waste heat generated from backup Internal Combustion Engines or Micro Gas Turbines can be used to satisfy local heating and cooling loads. As a result, there is an expectation that the overall efficiency and Greenhouse Gas Emissions of …

Next Generation Wireless Communication Networks: Energy And Quality Of Service Considerations, Md Munjure Mowla

Theses: Doctorates and Masters

The rapid growth in global mobile phone users has resulted in an ever-increasing demand for bandwidth and enhanced quality-of-service (QoS). Several consortia comprising major international mobile operators, infrastructure manufacturers, and academic institutions are working to develop the next generation wireless communication systems fifth generation (5G) - to support high data rates and increased QoS. 5G systems are also expected to represent a greener alternative for communication systems, which is important because power consumption from the information and communication technology (ICT) sector is forecast to increase significantly by 2030. The deployment of ultra-dense heterogeneous small cell networks (SCNs) is expected to …

Fe73.5si13.5b9cu1nb3 Metallic Glass: Rapid Activation Of Peroxymonosulfate Towards Ultrafast Eosin Y Degradation, Jincheng Wang, Zhe Jia, Peng Qin, W. C. Zhang, M. D. Wang, T. B. Sercombe, Laichang Zhang

Research outputs 2014 to 2021

Discovering functional applications of metallic glasses (MGs) as heterogeneous catalysts is a fundamental and essential topic. This work reports the rapid production of sulfate radicals (SO₄⁻) from peroxymonosulfate (PMS) using Fe_73.5Si_13.5B₉Cu₁Nb₃ glassy ribbons as catalysts for Eosin Y (EY) dye wastewater treatment. The reaction rates (k) from the experimental data reveal that the EY degradation is well fitted with the pseudo-first-order kinetic model. The strong electron transfer ability is characterized by electrochemical methods, presenting an advanced catalytic performance for EY degradation. Various experimental parameters, including dye …

Ransomware Behavioural Analysis On Windows Platforms, Nikolai Hampton, Zubair A. Baig, Sherali Zeadally

Research outputs 2014 to 2021

Ransomware infections have grown exponentially during the recent past to cause major disruption in operations across a range of industries including the government. Through this research, we present an analysis of 14 strains of ransomware that infect Windows platforms, and we do a comparison of Windows Application Programming Interface (API) calls made through ransomware processes with baselines of normal operating system behaviour. The study identifies and reports salient features of ransomware as referred through the frequencies of API calls

Copper Removal From Acid Mine Drainage-Polluted Water Using Glutaraldehyde-Polyethyleneimine Modified Diatomaceous Earth Particles, Mikael Larsson, Ataollah Nosratia, Simarpreet Kaur, Jochen Wagner, Ulf Baus, Magnus Nydén

Research outputs 2014 to 2021

Mine waters and tailings generated from mining and mineral processing activities often have detrimental impact on the local environment. One example is acid mine drainage, in which sulphides in the mining waste react with water and oxygen to produce an acidic environment that subsequently dissolves host rock minerals from the waste containing toxic metals and trace elements. Copper is one such metal of significance, as it is mined at large volumes in sulphide containing ores. It has strong biocidal activity that greatly affects ecosystems. We have previously reported that glutaraldehyde (GA)-crosslinked polyethyleneimine (PEI) has strong affinity and selectivity for copper …

Grey Wolf Optimization-Based Optimum Energy-Management And Battery-Sizing Method For Grid-Connected Microgrids, Kutaiba Sabah Nimma, Monaaf D. A. Al-Falahi, Hung Duc Nguyen, S. D. G. Jayasinghe, Thair Mahmoud, Michael Negnevitsky

Research outputs 2014 to 2021

In the revolution of green energy development, microgrids with renewable energy sources such as solar, wind and fuel cells are becoming a popular and effective way of controlling and managing these sources. On the other hand, owing to the intermittency and wide range of dynamic responses of renewable energy sources, battery energy-storage systems have become an integral feature of microgrids. Intelligent energy management and battery sizing are essential requirements in the microgrids to ensure the optimal use of the renewable sources and reduce conventional fuel utilization in such complex systems. This paper presents a novel approach to meet these requirements …

A Simplified Simulation Model To Estimate The Storage Length Of The Right-Turn Lane In Left-Hand Traffic At Signalised Intersections For Different Signal Phases And Cycle Timings, Noura Ishak-Thomas, Steven J. Richardson, Sanjay K. Shukla

Research outputs 2014 to 2021

Introduction:

A large number of the current guidelines and models are used to estimate the right-turn lane (RTL) length in left-hand traffic at signalised intersections under split phase, in which the movement of traffic in the right-turn lane and through lane happen concurrently. There is a need to examine other phase types and timings as a part of the RTL design. This is particularly significant in the case of established intersections that cannot be modified due to physical constraints.

Methods:

A MATLAB based simulation programme was developed to provide an estimate of the right-turn lane storage length for different traffic …

Ucs And Cbr Behaviour Of Perth Sandy Soil Reinforced With Waste Tyre Fibres And Cement, Seyed M. A. Bazazorde

Theses: Doctorates and Masters

Weak and unsuitable soil conditions have always caused problems for civil engineers during the construction of structures. To avoid problems in a cost-effective manner, proper and reliable solutions need to be developed. Fibre reinforcement and cement stabilisation are the most efficient and common methods in geotechnical engineering applications when engineers have problematic soil conditions. These methods can be used in different applications, such as pavement layers, retaining walls and slopes.

Over the past three decades, many studies have been done to investigate the effects of adding synthetic and natural fibres to soil as the reinforcing material alone or with cement. …

The Interaction Between Encapsulated Gd2o3 Particles And Polymeric Matrix: The Mechanism Of Fracture And X-Ray Attenuation Properties, Ly B. T. La, Christopher Leatherday, Peng Qin, Yee-Kwong Leong, Kevin Hayward, Bin Jiang, Lai-Chang Zhang

Research outputs 2014 to 2021

This work sheds light on the relationship between the quantities of synthesized core shell Gd₂O₃ added to epoxy matrix and the mechanical and X-ray attenuation properties of particulate epoxy composite. Then, an optimal geometric design of non-lead based X-ray protective material with light weight per volume unit is prepared. A plateau with 28–30 % increments in the value of fracture toughness (K_IC ) is observed with a specific addition of 0.08 – 0.1 volume fraction (φ_S) of Gd₂O₃ particles in pure epoxy. The same quantity of particles also optimally raises …

Universal Signal Conditioning Technique For Fiber Bragg Grating Sensors In Plc And Scada Applications, Gary Allwood, Graham Wild, Steven Hinkley

Research outputs 2014 to 2021

Optical fibre sensors, such as Fibre Bragg Gratings (FBGs), are growing in their utilisation, although very niche in their applications. To enable a more diverse range of end users, expensive application-specific optical fibre interrogation hardware needs to be made compatible with and, ideally, easily incorporated into existing instrumentation and measurement hardware. The Programmable Logic Controller (PLC) is an ideal example of hardware used for data acquisition in many industries. As such, a module that can be connected into an existing PLC slot to collect data from electrically-neutral, EMI-immune and versatile FBG sensors is of significant advantage to the growing optical …

Additive Manufacturing Techniques And Their Biomedical Applications, Yujing Liu, Wei Wang, Laichang Zhang

Research outputs 2014 to 2021

Additive manufacturing (AM), also known as three-dimensional (3D) printing, is gaining increasing attention in medical fields, especially in dental and implant areas. Because AM technologies have many advantages in comparison with traditional technologies, such as the ability to manufacture patient-specific complex components, high material utilization, support of tissue growth, and a unique customized service for individual patients, AM is considered to have a large potential market in medical fields. This brief review presents the recent progress of 3D-printed ­biomedical materials for bone applications, mainly for metallic materials, including multifunctional alloys with high strength and low Young’s modulus, shape memory alloys, …