Engineering Commons^™

Analysis And Mitigation Of Impacts Of Plug-In Electric Vehicles On Distribution System During Faults, Himanshu Bihani

All Theses

With rising concerns for environment, energy security and gasoline prices, penetration of plug-in electric vehicles (PEV) is bound to increase in the distribution system. The load characteristics of the distribution system with PEVs will be considerably different and hence its effects on the system needs to evaluated. Determination of the characteristics of the impacts will help utilities to prepare methodologies in advance to accommodate this new kind of load. Batteries of most of these vehicles will be charged using a single phase power electronic chargers. To study impact of these chargers on distribution system during fault and fault recovery is …

Electrokinetic Particle Manipulations In Spiral Microchannels, John Dubose

All Theses

Recent developments in the field of microfluidics have created a multitude of new useful techniques for practical particle and cellular assays. Among them is the use of dielectrophoretic forces in 'lab-on-a-chip' devices. This sub-domain of electrokinetic flow is particularly popular due to its advantages in simplicity and versatility. This thesis makes use of dielectrophoretic particle manipulations in three distinct spiral microchannels. In the first of these experiments, we demonstrate the utility of a novel single-spiral curved microchannel with a single inlet reservoir and a single outlet reservoir for the continuous focusing and filtration of particles. The insulator-based negative-dielectrophoretic (repulsive) force …

Adsorption Of Synthetic Organic Chemicals: A Comparison Of Superfine Powdered Activated Carbon With Powdered Activated Carbon, Semra Bakkaloglu

All Theses

In literature, manufacturer-supplied powdered activated carbon has been ground to produce submicron particles with mean diameter lower than 1µm for use as an adsorbent during water treatment. Superfine powdered activated carbon (SPAC) can be used for removal of natural organic matter as well as synthetic organic chemicals (SOCs) from water. It has been suggested that SPAC has higher adsorption capacity than powdered activated carbon (PAC) due to larger external surface area and mesopore volume. Another advantage of SPAC over PAC is the faster uptake rate for both NOM and SOC during adsorption owing to small particle size. Therefore, understanding SPAC …

Privacy Preserving Statistics, Oluwakemi Hambolu

All Theses

Over the past few years, there have been an increase in the development and improvement of circumvention tools like Tor and Psiphon. These tools provide an environment for citizens of oppressive regimes to access websites freely without fear of identification, these tools aid democracy activists and journalists in West Africa in using the Internet securely. A similar circumvention tool was developed by us. This tool circumvents DNS and IP address blocking/filtering, by leveraging technologies developed by criminal botnet enterprises. To improve and maintain the circumvention tool we developed, it is important to quantify the number and country of origin of …

Preliminary Evaluation Of Kenaf As A Structural Material, Andrew Sheldon

All Theses

Kenaf (Hibiscus cannabinus L.) is an annual fiber plant that is kin to cotton and okra and native to east-central Africa, though it is currently grown in numerous locations around the globe. The plant's apparent high strength and light weight along with its environmental and sustainability advantages makes it a good candidate for use in structural materials. The goal of this study was to design a kenaf product that resembled parallel strand lumber and required minimal processing of the kenaf. The mechanical properties of the two main components of kenaf, the bast fibers and the core, were evaluated using experimental …

Design Of A High Temperature Subsurface Thermal Energy Storage System, Qi Zheng

All Theses

Solar thermal energy is taking up increasing proportions of future power generation worldwide. Thermal energy storage technology is a key method for compensating for the inherent intermittency of solar resources and solving the time mismatch between solar energy supply and electricity demand. However, there is currently no cost-effective high-capacity compact storage technology available (Bakker et al., 2008). The goal of this work is to propose a high temperature subsurface thermal energy storage (HSTES) technology and demonstrate its potential energy storage capability by developing a solar-HSTES-electricity generation system. In this work, main elements of the proposed system and their related state-of-art …

A Comparative Study: Structural Complexity Metrics Applied Against Function And Assembly Product Graphs In Predicting Market Price And Assembly Time, Sri Ram Mohinder Cherkadu Vasala

All Theses

The overarching objective of this research is to investigate the measurement and use of complexity in the prediction of product performance metrics (assembly time and market cost) for two model graph types (assembly models and function structures). This research focusses on analyzing how accurate the prediction of performance metrics are based on these graph types. This research focuses on developing four prediction models: Function Structures to predict Market Price (FS-MP), Assembly Models to predict Assembly Time (AM-AT), Function Structures to predict Assembly Time (FS-AT), and Assembly Models to predict Market Price (AM-MP). These assembly models and function structures are analyzed …

A Study Of The Effects Of Manufacturing Complexity On Product Quality In Mixed-Model Automotive Assembly, Kavit Ravindra Antani

All Dissertations

The objective of this research is to test the hypothesis that manufacturing complexity can reliably predict product quality in mixed-model automotive assembly.

Originally, assembly lines were developed for cost efficient mass-production of standardized products. Today, in order to respond to diversified customer needs, companies have to allow for an individualization of their products, leading to the development of the Flexible Manufacturing Systems (FMS). Assembly line balancing problems (ALBP) consist of assigning the total workload for manufacturing a product to stations of an assembly line as typically applied in the automotive industry. Precedence relationships among tasks are required to conduct partly …

Isolated And Ephemeral Wetlands Of Southern Appalachia: Biotic Communities And Environmental Drivers Across Multiple Temporal And Spatial Scales, Joanna Hawley

All Dissertations

Throughout the world, wetlands are known to support a wide variety of taxa as well as high levels of biodiversity and species richness. Although the ecological significance of wetlands is well documented in the scientific literature, efforts to map and assess wetlands on regional or national scales (e.g., National Wetlands Inventory (NWI)) often overlook wetlands which are either very small (< 1 ha) or have ephemeral hydroperiods. While the vast majority of wetland research in the southeastern United States has focused on wetlands distributed across the coastal plain ecoregion, very little information exists on small and/or ephemeral wetlands in areas of southern Appalachia, although there are several notable exceptions. Despite the paucity of small wetland data in this region, the southeastern US is known as a hotspot for both aquatic biodiversity and species endemism. My goal with this project was to examine the biotic communities inhabiting small, ephemeral and geographically-isolated wetlands to identify the major environmental drivers that contribute to observed community patterns and species' distributions. I studied a set of small, mostly-ephemeral, mostly-isolated wetlands (N = 41) in the upper Piedmont and lower Blue Ridge ecoregions of South Carolina from January-June of 2010 and 2011 and focused my efforts on describing the structure, biotic communities and surrounding habitat characteristics of my study wetlands. I observed high levels of species richness and biodiversity in this previously-undocumented wetland system, despite the small size and ephemeral nature of study wetlands. My results indicated that the amphibian and benthic invertebrate communities of small, ephemeral wetlands responded to different environmental drivers (e.g., wetland depth, area, hydroperiod, canopy cover, surrounding land use types) occurring across multiple spatial and temporal scales. Additionally, the amphibian community was significantly influenced by a number of environmental variables occurring at both the within-pond scale and larger spatial scales (250 m, 500 m and 1 km surrounding land cover variables). By contrast, the benthic invertebrate community was significantly influenced primarily by variables occurring at the within-pond scale. This wetland system also served as both breeding and overwintering habitat for a variety of species such as wood frogs (Lithobates sylvatica), spotted salamanders (Ambystoma maculatum), bullfrogs (Lithobates catesbeiana), cricket frogs (Acris crepitans). This study highlights the ecological importance of small, ephemeral aquatic habitats in a region where little research exists regarding such systems; these often-unnoticed ecosystems are likely the result of a combination of historical anthropogenic and natural environmental process. These legacy wetlands (i.e., wetlands that are the unintended result of some human-induced environmental change in either the recent or long-term past) are found ubiquitously across the landscape and are often missed by coarse-filter mapping approaches (e.g., National Wetlands Inventory). I observed many study wetlands to be extremely small in size (< 0.05 ha) and that many wetlands were habitats of circumstance and opportunity rather than of permanence and predictability. The ephemerality of the majority of study wetlands demonstrates the biological significance of small, temporary habitats for many species requiring these habitats for breeding activity. Despite the small size and ephemeral nature of my study wetlands, I found that these wetlands represented a large proportion of amphibian biodiversity in the regional species pool and thus, are an important conservation feature at the local, landscape and regional scales. My study demonstrates that small, semi-isolated, mostly-ephemeral wetlands in southern Appalachia support high levels of biodiversity and are an important asset deserving of further study and conservation recognition.

Numerical Analysis Of The Extrusion Of Fiber Optic And Photonic Crystal Fiber Preforms Near The Glass Transition Temperature, Mohamed Trabelssi

All Dissertations

Conventional clad core fiber optic technology has relied on a concentric structure of glass of different refraction indices. These conventional fibers suffer from constraints and limitations related to thermal expansion compatibility between the core and the glass. The new fiber technology broadly characterized as Microstructured Optic Fibers (MOFs) is intended to lift the limitations of conventional clad core fibers and also extend the range of application of fiber optics. Photonic Cristal Fibers(PCFs) are a special family of Microstructured Optic Fibers characterized by the presence of holes in the cross section of the fiber that are organized in a hexagonal pattern. …

Drug Delivery With Feedback Control In Bioresponsive Hydrogels, Andrew Wilson

All Dissertations

Bioresponsive hydrogels are emerging with technological significance in targeted drug delivery, biosensors and regenerative medicine. The design challenge is to effectively link the conferred biospecificity with an engineered response tailored to the needs of a particular application. Moreover, the fundamental phenomena governing the response must support an appropriate dynamic range, limit of detection and the potential for feedback control. The design of these systems is inherently complicated due to the high interdependency of the governing phenomena that guide sensing, transduction and actuation of the hydrogel. The objective of the dissertation is to review the current state of bioresponsive hydrogel technology …

Inkjet Printing Of Three-Dimensional Vascular-Like Constructs From Cell Suspensions, Changxue Xu

All Dissertations

Inkjet printing has found an increasing number of biofabrication applications, specifically organ printing, which has been emerging as a promising solution to the organ donor shortage. While some studies have been conducted to investigate various engineering problems associated with DOD inkjet printing of biological material-based fluids, the pinch-off, the cell-laden droplet formation, the effects of electric field on droplet formation, and challenges in 3D vascular-like construct fabrication haven't been systematically investigated. The objective of this study is to investigate the pinch-off, the cell-laden droplet formation, the effects of electric field on droplet formation, and manufacturing challenges during fabrication using DOD …

Emc In Power Electronics And Pcb Design, Chentian Zhu

All Dissertations

This dissertation consists of two parts. Part I is about Electromagnetic Compatibility (EMC) in power electronics and part II is about the Maximum Radiated Electromagnetic Emissions Calculator (MREMC), which is a software tool for EMC in printed circuit board (PCB) design. Switched-mode power converters can be significant sources of electromagnetic fields that interfere with the proper operation of nearby circuits or distant radio receivers. Part I of this dissertation provides comprehensive and organized information on the latest EMC developments in power converters. It describes and evaluates different technologies to ensure that power converters meet electromagnetic compatibility requirements. Chapters 2 and …

The Development Of Empirical Models To Evaluate Energy Use And Energy Cost In Wastewater Collection, David Young

All Dissertations

This research introduces a unique data analysis method and develops empirical models to evaluate energy use and energy cost in wastewater collection systems using operational variables. From these models, several Best Management Processes (BMPs) are identified that should benefit utilities and positively impact the operation of existing infrastructure as well as the design of new infrastructure. Further, the conclusions generated herein display high transferability to certain manufacturing processes. Therefore, it is anticipated that these findings will also benefit pumping applications outside of the water sector. Wastewater treatment is often the single largest expense at the local government level. Not surprisingly, …

Design And Analysis Of Electromagnetic Interference Filters And Shields, Andrew Mcdowell

All Dissertations

Electromagnetic interference (EMI) is a problem of rising prevalence as electronic devices become increasingly ubiquitous. EMI filters are low pass filters intended to prevent the conducted electric currents and radiated electromagnetic fields of a device from interfering with the proper operation of other devices. Shielding is a method, often complementary to filtering, that typically involves enclosing a device in a conducting box in order to prevent radiated EMI. This dissertation includes three chapters related to the use of filtering and shielding for preventing electromagnetic interference. The first chapter deals with improving the high frequency EMI filtering performance of surface mount …

Adaptive And Robust Braking-Traction Control Systems, John Adcox

All Dissertations

The designs of commercial Anti-Lock Braking Systems often rely on assumptions of a torsionally rigid tire-wheel system and heavily rely on hub-mounted wheel speed sensors to manage tire-road slip conditions. However, advancements in high-bandwidth braking systems, in-wheel motors, variations in tire/wheel designs, and loss of inflation pressure, have produced scenarios where the tire's torsional dynamics could be easily excited by the braking system actuator. In these scenarios, the slip conditions for the tire-belt/ring will be dynamically different from what can be inferred from the wheel speed sensors. This dissertation investigates the interaction of tire torsional dynamics with ABS & traction …

Comparison Of The Design-Bid-Build And Construction Manager At Risk Project Delivery Methods Utilized For The Construction Of Public Schools, Noel Carpenter

All Dissertations

No

Using Hidden Markov Models To Segment And Classify Wrist Motions Related To Eating Activities, Raul Ramos Garcia

All Dissertations

Advances in body sensing and mobile health technology have created new opportunities for empowering people to take a more active role in managing their health. Measurements of dietary intake are commonly used for the study and treatment of obesity. However, the most widely used tools rely upon self-report and require considerable manual effort, leading to underreporting of consumption, non-compliance, and discontinued use over the long term. We are investigating the use of wrist-worn accelerometers and gyroscopes to automatically recognize eating gestures. In order to improve recognition accuracy, we studied the sequential ependency of actions during eating. In chapter 2 we …

Battery Second Use: A Framework For Evaluating The Combination Of Two Value Chains, Melissa Bowler

All Dissertations

A Battery Second Use (B2U) strategy is the design and development of a battery system with the intention of having it serve two purposes: (1) the initial use in the vehicle and (2) another mobile or stationary application. An optimal battery second use strategy requires the design and use of the battery to maximize the value of the system over its entire extended life cycle. Within this thesis a framework is developed which allows the evaluation of tradeoffs along the operational second use value chain.

Numerical Investigation Of One-Dimensional Shallow Water Flow And Sediment Transport Model Using Discontinouous Galerkin Method, Farzam Safarzadeh Maleki

All Dissertations

A one-dimensional shallow water flow and sediment transport model is developed using a discontinuous Galerkin finite element scheme. As a first step, four different time marching schemes as well as three different slope limiters have been investigated to find the optimum modeling combination. The efficiency and accuracy of the time marching schemes and slope limiters are quantitatively examined using CPU runtime and comparison between the simulated results and theoretical/experimental data. It is found that using the second order Adam-Bashforth time marching scheme and Monotonized Central method leads to most efficient and accurate results. As the second part of this research, …

Connect With Bioengineering Researchers And Entrepreneurs, Clemson University

Bioengineering

2014 Program for Connect with Bioengineering Researchers and Entrepreneurs at Madren Conference Center.

Development Of Multimodal Membrane Adsorbers For Antibody Purification Using Atom Transfer Radical Polymerization, Juan Wang, Scott M. Husson

Graduate Research and Discovery Symposium (GRADS)

No abstract provided.

Carbon Fibers Derived From Sustainable Precursors, Meng Zhang, Jing Jin, Amod A. Ogale

Chemical and Biomolecular Graduate Research Symposium

No abstract provided.

Producing A Liquid-Lignin Phase From Kraft Black Liquor: Phase Behavior And Structural Characterization, Julian Velez, Mark C. Thies

Chemical and Biomolecular Graduate Research Symposium

No abstract provided.

Density Functional Theory-Based Modeling Of Catalyzed Water Purification, Lizzie Bollman

Chemical and Biomolecular Graduate Research Symposium

No abstract provided.

Effect Of Co Adsorption And Coverage On Ethanol Production From Syngas, Anuradha Gundamaraju, Ming He, David A. Bruce

Graduate Research and Discovery Symposium (GRADS)

In the future, the availability of reliable alternative fuels will be crucial for any country to become energy independent. One such alternative is ethanol as it can be used both as a fuel and as a fuel additive. Most of the ethanol produced in the world today is derived from biomass. The biomass feedstocks and fermentation broths used in ethanol production both contain high amounts of water and therefore, the energy efficiency of the process is lessened by product separation processes (azeotropic separation of water and ethanol) that are non-trivial and highly inefficient (due to the evaporation of water). An …

Template Free-Synthesis Of Polypyrrole Microtubes For Supercapacitor Electrodes, Kryssia P. Diaz, Mark E. Roberts

Graduate Research and Discovery Symposium (GRADS)

The purpose of this work is to develop a simple, scalable and template-free method to synthesize conducting polymer nano/micro-structures for supercapacitor electrodes. The microstructure and electrochemical properties of structure polypyrrole on various mesh substrates is investigated.

Recovering A Liquid-Lignin Phase From Paper Mill Black Liquors, Julian Velez, Adam Klett, Mark C. Thies

Graduate Research and Discovery Symposium (GRADS)

No abstract provided.

Analysis Of Solvation Model, Adsorption Site, And Adsorbate Coverage Effects On Adsorption Energies At The Anode In Direct Methanol Fuel Cells, Cameron J. Bodenschatz, Rachel B. Getman

Graduate Research and Discovery Symposium (GRADS)

No abstract provided.

Synthesis And Characterization Of Extractive Scintillating Resin For Ultra-Trace-Level Quantification Of Uranium In Aqueous Media, C Duval, V Bliznyuk, A Seliman, T Devol, S Husson

Graduate Research and Discovery Symposium (GRADS)

The detection and quantification of radionuclides in aqueous media is of interest to both the Environmental Protection Agency, for matters of public health, and international organizations like the Comprehensive Test Ban Treaty Organization, that use environmental samples to investigate claims of illicit nuclear activities. The current method of quantification involves batch style analytical techniques which utilize bulky instruments. Portable, flow cell detectors utilizing extractive scintillating resin with physically sorbed extractants and fluorophores have been developed; however, this resin shows poor long term stability as the active components leach from the resin over time. There is a need to develop chemically …