Engineering Commons^™

Motor Reference, Mohamed Grissa

BioResource and Agricultural Engineering

This document contains summary information about the following motor topics:

• Motor selection information
• AC induction motors
• Inverter duty motors
• Variable frequency drives
• Motor losses
• Troubleshooting

The information contained in this document was gathered from a variety of online, interview, and print sources, including NEMA specifications, with support from the California Energy Commission (CEC) PIER Program.

Drip Irrigation System Cost Sharing By Irrigation Districts For Water Conservation, Charles M. Burt

BioResource and Agricultural Engineering

Government and irrigation district cost sharing programs have often included financial support for the installation of drip/micro irrigation systems. These programs seek advantages that might include improved crop yield, less applied water, and a reduction in subsurface drainage water and surface tailwater. They may also seek to reduce water consumption. The actual results have been shown to vary by district, hydrology, and crop.

It is true that drip systems in California, on average, have good Distribution Uniformities (DU) of irrigation water – meaning that there are only minor differences between the depths of water received by various plants throughout a …

Low-Cost Prosthetic Leg For The Vida Nueva Prosthesis Clinic, Sarah M. Baker, Justin G. Lekos, Jen Van Donk, Kevin Yamauchi

Mechanical Engineering

The Piernas de Vida team partnered with the Vida Nueva Clinic of Prostheses and Orthoses in Choluteca, Honduras to design, plan, and implement a prosthetic foot that could be manufactured entirely by the technicians at the clinic in order to reduce their costs and ultimately allow them to serve more patients each year. Currently, the clinic uses a prefabricated prosthetic lower limb provided by the International Committee of the Red Cross (ICRC) which can be adapted to both transDfemoral and transDtibial patients. The team has successfully developed a foot, currently called the Layer Foot, which can be used by the …

Bond Behavior Of Fiber Reinforced Polymer Bars Under Hinged Beam Conditions, Ryan James Sandstrom

Master's Theses

The research provided in this report examines the behavior of fiber reinforced polymer (FRP) reinforcing bars, embedded in normal weight concrete (NWC) hinged beam-end specimens, tested in accordance with two laboratory conditions. Reinforcing bars of different diameter, material configuration, and finished surface preparation were tested for bond strength parameters determined in accordance with ACI Committee Report 440.3. Bond strength parameters under the first condition were tested within NWC beams at a relatively low compressive strength and minimum embedment length; the second condition allowed testing within NWC beams at twice the design compressive strength of the first condition and moderate embedment …

Aether, Thomas Cameron, Kristine Colton, Daren Childers

Electrical Engineering

Aether is a RC-style autonomous air vehicle that utilizes GPS positioning along with a wireless communication system to achieve a computer-controlled flight.

This report will incorporate the acquisition, design, integration, implementation and testing phases of the UAV development. Furthermore a discussion of troubleshooting as well as improvements for future projects will be included.

Wireless Energy Transfer, Ryan Sasur

Electrical Engineering

Phones are now an integral component in the daily lives of people. Smartphones give access to movies, internet, and even books. This versatility and increased use can also lead to a shorter battery life. A phone with video viewing capabilities will be a heavy load on the unit’s battery. With phones utilizing 3G and 4G technology, even heavier demands are placed on the battery. As technology improves even further to provide for a larger entertainment experience on the phone, this could also lead to further battery degradation if the current battery situation isn’t addressed. To have a fully operational phone …

Hydro-Electric Generation System For The Dc House Project, Dennis Kwan, Mitchell Krug

Electrical Engineering

This paper focuses on the design, integration, and construction of a system that harnesses energy from flowing water. The system will be used in conjunction with the DC House Project. The proposed system employs a DC generator and DC-DC Boost-converter to provide electricity to the DC House at approximately 200-300W. Results of the testing and measurement show that the goal of the system is feasible, but currently limited. The generator could not output the specified power. Details of the design, along with ideas for further improvement, are presented in this report.

Audio-To-Optical Conversion And Transmission, Jason Moritz

Electrical Engineering

The purpose of this project is to understand free-space optical transmission of signals in the application of transmitting an audio signal. An audio signal will be taken from the headphone output of a computer and used to modulate a current source driving an LED and a laser diode. The optical signal will then be transmitted through free space as well as two different focal length lenses and converted back to an audio signal to measure any attenuation or gain in the original signal. My experimental results showed that the LED was able to transmit up to 10 dB more power …

Multicore, Multithreaded, Phase-Synchronous Fm Sound Synthesizer, Justin Tomlin

Electrical Engineering

This project implements a phase-synchronous FM synthesis algorithm in hardware.  Envelope and low frequency oscillator modulation of oscillator parameters is implemented.  The microcontroller the system is based on, the XMOS XS1-G4, allows for physical parallelism including features such as multiple cores, multiple hardware threads on each core, a hardware event-driven thread scheduler, and channel, channel ends, and link switches for thread and core communication.  The event-driven architecture of this device was ideal for implementing this synthesis algorithm.  The final product is portable, durable, has a simple, intuitive user interface, and allows for extensive spectral shaping capabilities.  The basic functional requirements …

10-Band Graphic Equalizer, Sean William Michel

Electrical Engineering

No abstract provided.

An Advanced Controller For A Semi-Active Wheelchair Suspension, David J. Smith

Master's Theses

An Advanced Controller for a Semi-Active Wheelchair Suspension was designed, built and tested.  The suspension consisted of a Goodyear 1S3-011 air spring, IQ Valves high speed proportional solenoid valve, and a custom made accumulator.  Several controller designs specific to semi-active suspensions were designed and tested.  The controllers investigated were skyhook, acceleration driven damping, and a combined control law employing both a dual and single sensor version.  The implementation of skyhook control suffered performance degradation from the idealization due to particular elements of hardware, however acceleration driven damping showed a marked and statistically significant improvement over skyhook control, in hardware, by …

Arteriogenesis And Ischemia Impair Functional Vasodilation In Resistance Arteries, Trevor Cardinal, Joseph S. Zhu, Kyle R. Struthers, Thomas J. Kesler, Matthew D. Yocum

Biomedical Engineering

No abstract provided.

X-51 Composite Airframe, Brendon J. Townshend

Aerospace Engineering

This paper gives an overview of the progress that has been made in the design build of the X-51.  The X-51 is a composite scale replica of a P-51D fuselage integrated with a P-51H wing.  Issues with the airframe as well as current action items are discussed, as well as findings so far in preliminary design.

Mapping Galileo's Trajectory, Mark Woods

Aerospace Engineering

The NASA Galileo mission was mapped out using a patched conics approximation.  Galileo launched from Earth, underwent a gravity assist from Venus back to Earth for another gravity assist.  Galileo then came back to Earth for one more gravity assist to propel it to Jupiter.  A simulation ignoring all perturbations (i.e. third body effects, zonal (harmonics, solar wind, drag) was carried out.  The simulation was able to make it to the final Earth flyby before diverging from the actual trajectory.  The simulated and actual flyby dates all differed by less than 5 hours, and the simulated and actual flyby altitudes …

Analysis Of Surface Augmentation Of Airfoil Sections Via Flow Visualization Techniques, John Louis Vento

Aerospace Engineering

This report details an experiment done to verify the effectiveness of two passive flow control systems on two-dimensional airfoil sections. The flow control was tested on two types of airfoils: a symmetric NACA 0011, intended to represent an airplane in cruise, and a NACA16611, intended to represent an aircraft with flaps extended.  Two types of passive systems were employed, a dimple surface augmentation, similar to a golf ball, and a grit system located at 20% chord. Airfoils without either augmentation were tested as a control case. Using a water tunnel and dye to perform flow visualization, the effects of each …

Flight Testing In A Simulation Based Environment, David W. Babka

Aerospace Engineering

Over the past two decades performance flight testing of full scale aircraft has transferred some of the testing workload to simulation based systems.  Flight testing full scale aircraft in the real world environment has always been expensive, especially now with the rise in aviation fuel costs. Additionally, new emerging technologies require extensive testing and doing so in the full scale environment is cost prohibitive.  A cheaper alternative is to test systems in a simulation based environment.  Not only can aircraft be simulated via a computer, but all the aircrafts systems can be modeled in the simulation.  Furthermore, most of the …

Micro-Forest Fire Detection (Mffd) Lwir Detector And Principle Component Analysis For Fire Detection, Bryce Du

Electrical Engineering

No abstract provided.

Life Cycle Inventory Of Hdpe Bottle-Based Liquid Milk Packaging Systems, Jay Singh, Aric Krasowski, S. Paul Singh

Industrial Technology and Packaging

This study aims at providing a relatively straightforward methodology to serve as a decision-making tool when more than one packaging solution could be available to a user. It involves a life cycle inventory (LCI) analysis and comparison of three currently available 3.79 l (1 gallon) packaging systems for liquid milk. Two of the primary container types studied use reusable plastic crates (RPCs) for stacking and shipping,
while the third type is a heavier duty container that does not require secondary shipping containers. The three primary containers studied are identified as original, cube and stackable throughout this paper. The study shows …

A Multiple Performance Analysis Of Market-Capacity Integration Policies, Ahmed M. Deif, Hoda A. Elmaraghy

Industrial Technology and Packaging

A model that uses simulation augmented with Design of Experiments (DOE) is presented to analyse the performance of a Make-to-Order (MTO) reconfigurable manufacturing system with scalable capacity. Unlike the classical capacity scaling policies, the proposed hybrid capacity scaling policy is determined using multiple performance measures that reflect cost, internal stability and responsiveness. The impact of both tactical capacity and marketing policies and their interaction on the overall performance was analysed using DOE techniques and real case data. In addition to the different insights about the trade-offs involved in capacity planning decisions, the presented results challenged the conventional capacity planning wisdoms …

Characterization Of Bioreactor System For Tissue Engineered Blood Vessels, Kasim Shah

Biomedical Engineering

No abstract provided.

The Effects Of Anti-Price Gouging Legislation On Supply Chain Dynamics, Jason Edward Maynard

Master's Theses

The purpose of this thesis is to model the effects of anti-price gouging (APG) legislation on the costs to businesses during the recovery period of a disaster. A system dynamics model of a business’s replenishment procedures is used to simulate the effects of APG legislation on business performance. Economists have published expansive research on the effects of price ceilings on supply and demand, but there is little research evidence on the operational consequences of price ceiling legislation on business costs. APG legislation increases consumer’s forward buying and shortage gaming after a disaster by removing price incentives to be frugal. Forward …

Irrigation District Turnouts, Charles M. Burt

BioResource and Agricultural Engineering

This is meant to be a very quick, roughly written primer on irrigation district turnout selection. It by no means covers all of the details, but it might help out. ITRC offers flow measurement classes, with online registration at www.itrc.org. We have also done testing on quite a few designs over the years, but the work was almost all confidential in nature.

2d Motion Detection Bounded Hand 3d Trajectory Tracking And Gesture Recognition Under Complex Background, Shuangqing Wu, Yin Zhang, Sanyuan Zhang, Xiuzi Ye, Yiyu Cai, Jianmin Zheng, Soumita Ghosh, Wenyu Chen, Jane Zhang

Electrical Engineering

In this paper, a 2D motion detection bounded hand 3D trajectory tracking and gesture recognition system is proposed for virtual reality interactions. First, the Bayes decision rule for classification of background and foreground is utilized to automatically locate the hand that bounded within a rectangle, and then the trajectory of the hand in 3D space is tracked by mean shift particle filter and stereo imaging. The skin color feature is exploited for image matting that effectively segment the hand contour in video sequence automatically. Finally the hand gesture is recognized by the connected component analysis and line approximation.

Real-Time 3d Markerless Multiple Hand Detection And Tracking For Human Computer Interaction Applications, Soumita Ghosh, Jianmin Zheng, Wenyu Chen, Jane Zhang, Yiyu Cai

Electrical Engineering

In this paper we present a purely vision based implementation of markerless hand detection and tracking system which effectively detects and tracks the hand positions irrespective of hand orientation. A shape based detection algorithm using a new line approximation technique followed by an adaptive minimum distance classifier based tracking technique is implemented. The technique is very generic and can be practically used in all types of immersive and semi-immersive environments like simulations, three-dimensional (3D) games, visually assisted medical surgery and other humancomputer interactive applications.

Intelligent Planning And Assimilation Of Auv-Obtained Measurements Within A Roms-Based Ocean Modeling System, Benjamin J. Davini

Master's Theses

Efforts to learn more about the oceans that surround us have increased dramatically as the technological ability to do so grows. Autonomous Underwater Vehicles (AUVs) are one such technological advance. They allow for rapid deployment and can gather data quickly in places and ways that traditional measurement systems (bouys, profilers, etc.) cannot. A ROMS-based data assimilation method was developed that intelligently plans for and integrates AUV measurements with the goal of minimizing model standard deviation. An algorithm developed for this system is first described that optimizes paths for AUVs that seeks to improve the model by gathering data in high-interest …

Investigating Wood Welding Parameters Using A Prototype Welding Machine, Timothy R. Melin

Master's Theses

Understanding how different processing variables influence wood welded bonds is vital if the technique will ever be used to create engineered lumber without using adhesives. A variation of vibration welding, wood welding uses pressure and friction to bond materials together. During welding, heat causes a softening in the wood, a naturally occurring composite material. This softening leads to fiber entanglement and a bond forms upon cooling.

The goal of this research was to investigate several processing aspects of the wood welding procedure. A prototype wood welding machine, designed and fabricated from the ground up, was used to investigate the effects …

Sustainable Climate Control For Mid-Rise Office Building In The Salt Lake Valley, Philip M. Coleman

Industrial and Manufacturing Engineering

This report examines the sustainability of Trane’s EarthWiseTM climate control systems in the Salt Lake Valley (and the United States Mountain West in general). A simulation is performed to determine the best climate control system for a LEED Silver, 5-story tenant office building. This new building is a duplication of a pre-existing building. The climate control system installed at the preexisting building is used as a baseline against which three (3) alternative systems are compared. The social, ecological, and economic impact of each alternative is examined to determine which is the most sustainable. Since the baseline system is a proven …

Automation Of Pillow Speaker Button Testing To Avoid Repetitive Strain Injuries In Testing Technicians, Tyler P. Finnegan

Industrial and Manufacturing Engineering

Abstract Anacom MedTek, a medical device company, produces pillow speakers as their main product line. Pillow speakers are a healthcare communications tool that allow for hospital patients to control many entertainment and environmental components of the hospital room from one controller. These pillow speaker devices have anywhere from 3 to 27 metal dome key cap buttons based on their customization. Before they can be shipped to a customer, each button must be tested to ensure that it is functioning properly. This test is currently done manually by a testing technician. With so many buttons to be tested for each unit …

Pull Production System Training Guide, Adem Bilgutay

Industrial and Manufacturing Engineering

This book is a series of lessons designed to train operators and managers in pull manufacturing. It begins with a description of the different forms of waste that a system can help to identify and eliminate. The second section details the kanban as a system for controlling flow and as a powerful tool for identifying problems. It will describe the many different variations of kanban that exist to control flow in different production environments and the calculations that allow them to be used effectively. The final section will detail the activities that an operator should engage in when there is …

Modeling And Preliminary Finite Element Analysis On The Spun Structure For The Cpintersep Project, Jason Carpenter, Kelly Cheng, Jeffrey Ma, Richard Pelham, Kevin Povey

Aerospace Engineering

This paper details the process of modeling and importing the model into FEA for the spun structure of the BS376 spacecraft. Engineering drawings were converted into 3D models using Pro/Engineer and then imported and into Patran for pre-processing of a Finite Element Model. To verify the Finite Element Model, several test cases were set up and solved using Nastran solver. Our simple load cases were found to be in congruence with analytical solution methods validating the finite element model.