Engineering Commons^™

Quantifying The Life Cycle Benefits Of Performance-Based Design In Sustainable Design, David Isaac Carmona

Master's Theses

ABSTRACT

Quantifying the Life Cycle Benefits of Performance-Based Design in Sustainable Design

David Carmona

For this thesis, a method is developed and tested for use with performance based design to quantify the sustainable and financial benefits of designing buildings to a structural performance level higher than Life-Safety. This paper starts to answer the question, “which would be a better investment: build structures to a performance level of Immediate Occupancy (IO) with the likelihood of less damage and downtime after an earthquake or continue to build to the building code’s implied minimum performance level of Life-Safety (LS)?”

An ASCE 7-05 designed …

Nonlinear Uav Flight Control Using Command Filtered Backstepping, Brian M. Borra

Master's Theses

The aim of this effort is to implement a nonlinear flight control architecture, specifically flight path control via command filtered backstepping, for use in AME UAS's Fury® 1500 unmanned flying wing aircraft. Backstepping is a recursive, control-effort minimizing, constructive design procedure that interlaces the choice of a Lyapunov function with the design of feedback control. It allows the use of certain plant states to act as intermediate, virtual controls, for others breaking complex high order systems into a sequence of simpler lower-order design tasks.

Work herein is a simplified implementation based on publications by Farrell, Sharma, and Polycarpou. Online approximation …

Design, Acnd Construction Of A Portable Artificial Insemination Chute, Chris Herrera

BioResource and Agricultural Engineering

This senior project report discusses the design, construction, and evaluation of a portable artificial insemination chute for the use of the Cal Poly Beef Department. The design was based on the suggested modifications from operators of several other chutes currently in use.

The main areas considered for the design were; Ergonomics, cattle safety, factors effecting maximum breeding conception rates, and Portability.

The breeding chute proved superior over traditional chutes in a variety of ways. Improvement occurred in the areas of consideration as follows, user operation was simplified, animal stress was decreased, and maximum breeding efficiency was obtained.

Rapid Battery Exchange For Electric Vehicles, Michael Cocchi, Adam Rizkalla

Computer Engineering

No abstract provided.

Car Alarm System, David Lane

Electrical Engineering

This project entails the design and implementation of a car alarm system for a 1977 Volkswagen Beetle.

Pedaling And Braking Forces And Their Effect On Suspension Performance, Kathleen Kramer, Nik Goodell, Cesar Giron

Mechanical Engineering

The goal of this project is to produce a quantifiable relationship between pedaling and braking forces and suspension behavior. The test results will serve as a benchmark, against which other suspension designs can be compared in an objective, numerical manner. This report details the work completed towards determining this relationship and is primarily focused on design development of the data acquisition system and analysis of braking forces, pedaling forces and suspension response. A 2011 Specialized Stumpjumper FSR Expert Evo was used as the development platform. The system will be used to measure various rear suspension designs for comparison.

Rapid Battery Interchange System, Mason Borda

Electrical Engineering

As our nation strives towards a departure from widespread use of fossil fuels, we must focus on a plan for what is to be the substitute for Internal Combustion Engine vehicles as well as the infrastructure to support this. The most popular alternative to the internal combustion engine is the electrically propelled vehicle, one that can provide us with many benefits including simplified construction, lower operational costs, and for the driving enthusiasts more torque. The prevailing issue in the widespread acceptance and use of the electric vehicle thus far is “range anxiety”. Range anxiety is defined as “The fear of …

Beneficial Reuse Of Corrugated Paperboard In Civil Engineering Applications, Gregory M. Stone

Master's Theses

Abstract

Beneficial Reuse of Corrugated Paperboard in Civil Engineering Applications

Gregory Michael Stone

An investigation was conducted to explore the potential for reuse of corrugated paperboard. Corrugated paperboard represents a large fraction of the municipal solid waste generated and discarded in the United States. Alternative applications for reuse can provide a significant benefit by reducing the volume of waste being disposed and by reducing the use of raw materials. Four civil engineering applications were examined for potential beneficial reuse of corrugated paperboard: slurry trench construction, vertical drilling, directional drilling, and controlled low strength materials (CLSM).

For the purpose of this …

Experimental Investigation Of A 2-D Air Augmented Rocket: High Pressure Ratio And Transient Flow-Fields, Josef S. Sanchez

Master's Theses

A 2-D Air Augmented Rocket, the Cal Poly Air Augmented Rocket (CPAAR) Test Apparatus operating as a mixer-ejector was tested to investigate high stagnation pressure ratio and transient flow fields of an ejector. The primary rocket ejector was supplied with high pressure nitrogen at a maximum chamber pressure of 1758 psia and a maximum mass flow rate of 1.4 lb/s. The secondary flow air was entrained from a fixed volume plenum chamber producing pressures as low as 3.3 psia. The maximum total pressure ratio achieved was 221. The original CPAAR apparatus was rebuilt re-instrumented and capability expanded. A fixed volume …

Ql+ Body Temperature Regulating Vest, Melissa Goss, Brittnee Cubero, Dillon Lynch, Greg Olsen, Julian Jazayeri

Biomedical Engineering

The purpose of this project is to design a thermal vest to be worn by individuals with spinal injuries to help regulate their core body temperature. Individuals with spinal injuries have impaired thermoregulation abilities which increase their susceptibility to succumbing to either heat stroke or hypothermia. This project focused on preventing heat stroke by inducing a cooling mechanism. To provide this cooling mechanism, a thermoelectric cooler was used to chill water in a reservoir. This water is then pumped through tubing sewn into the vest. The chilled water will absorb heat from the human body and return to the reservoir. …

The Importance And Challenge Of Launch Environment Testing, Christina Diaz

Aerospace Engineering

This report discusses the purpose and effect of environmental testing, particularly vibration, shock and acoustic tests, in the aerospace industry. Vibration, shock, and acoustic testing are methods that are used to quantify and analyze the physical phenomenon of the launch environment on a payload or launch vehicle. The importance of innovation in testing and understanding of failures is crucial to a successful spacecraft mission. The advancement and precision of these testing methods is also explored in this report such as the invention of the 6 Degree of Freedom (DoF) vibration table and solutions to data acquisition issues recently discovered in …

On-Farm Irrigation Tracking Software For The Imperial Valley, Taylor Andrew Brady

BioResource and Agricultural Engineering

In order to improve on farm irrigation, a water scheduling program specific to the needs of Imperial Valley farmers will be created. The program will help keep track of daily water schedules, as well as stay connected with the farm personnel to reduce error and save time. The program will help with on farm operations and productivity by allowing the famer, irrigation foremen, and secretary to view the same schedule simultaneously. The information that is inputted into the program will be editable by all the chosen personnel, to keep everyone on the same page. Weekly, monthly, or yearly usage reports …

Expansion Of A Dust Removal System For The Brae Department Plasma Table, Derek Hansen

BioResource and Agricultural Engineering

This senior project discusses the expansion of a dust removal system for welding and cutting fumes. A Donaldson Torit Powercore TG8 dust collector is used to collect and process the fumes created during welding and cutting operations that take place in the BioResource and Agricultural Engineering department at Cal Poly San Luis Obispo. Expansion of the system allows for greatly increased utilization of the TG8 and a cleaner working environment in Lab #6. Testing shows that the system fluently changes between the plasma table and the three hoods in the shop. Each hood is only capable of collecting a smoke …

Lunalight Project: Solar-Rechargeable Led Lantern And Cell Phone Charger, Sean C. Dawson, Michael E. Deagen, Francisco N. Dye, Brian S. Mircheff, Ryan O. Ramelb

Materials Engineering

Today, 1.6 billion people in the world do not have access to grid electricity. Villagers living off the grid in developing nations resort to kerosene lanterns to light their homes. The fumes from burning kerosene are toxic and lead to respiratory illnesses over time. Our sponsor, OneMillionLights, plans to help people to escape poverty by providing them with a clean source of light at night. Children that must work in the fields during the day can use a solar-rechargeable lantern at night to read or study, and street vendors can use the lanterns at night to improve their businesses.

The …

Fire And Life Safety Analysis Of The Performing Arts Center's Christopher Cohan Center, David Phillips

Fire Protection Engineering: Culminating Experience Project Reports

This report is a review of the fire protection systems installed in the Christopher Cohan Center on the Cal Poly, San Luis Obispo campus. The systems reviewed are the passive structural fire protection, passive and active egress components, and active detection and suppression systems. The report examines whether the reviewed systems in the building meet the prescriptive requirements of the 2010 California Building Code(CBC) and California Fire Code(CFC). The building will be further subjected to a performance based analysis. Two design fire scenarios are presented, and an analysis of available safe egress time (ASET) is compared with an analysis of …

Fire Protection Analysis Of The Orfalea College Of Business Building (#3), William Fletcher

Fire Protection Engineering: Culminating Experience Project Reports

A performance and prescriptive based analysis was performed on the Orfalea College of Business Building (#3) on Cal Poly’s Campus. The building was originally designed to meet the 1985 Uniform Building Code (UBC). The building’s original design and current existing condition will be examined. The business building will be evaluated using the California Building Code, California Fire Code, NFPA 101 Life Safety code and other relevant NFPA Codes. The fire protection systems will be separated and evaluated into systems by Egress Components, Fire Alarm and Detection, Water- Based Suppression and Structural Fire Protection. The combined interactions of the systems are …

Development Of A Standardized Method For Comparing Biomechanical Properties Of Various Sternal Closure Techniques, Ramzi P. Hawit

Master's Theses

Background:

33.6% of all deaths in America are caused by cardiovascular disease. An estimated 82.6 million adults (>1 in 3) in America have some form of cardiovascular disease. There were over 400,000 bypass surgeries requiring open-heart surgery. Sternal dehiscence is associated with a morbidity rate of over 47% if mediastinitis supervenes. A rigid closure is required to avoid healing complications, and wire, plates, and bands are all used in an attempt to make a better closure. The purpose of this study it to compare multiple closures and validate a new testing method.

Methods:

Polyurethane foam blocks will be used, …

Dc Dielectrophoretic Assisted Anti-Fouling Filtration System, Nathan M. Cohen

Master's Theses

Filtration processes, whether on the microfluidic, clinical treatment systems, or industrial scale (e.g., point-of-care diagnostics, dialysis, and biopharmaceutical manufacturing, respectively), are often inseparable from membrane clogging (fouling). As a consequence, most, if not all, filtration systems require frequent maintenance to maintain functionality and efficiency. The thesis of this project hypothesizes that Dielectrophoresis can be combined with standard filtration to reduce filter fouling, extending membrane life, and enabling continuous operation. This project investigates a method to reduce fouling, add specificity and efficiency, and decrease the cost and challenge of filtration based biofluid separations.

To substantiate this thesis, we designed, fabricated, and …

Effect Of End-Plate Tabs On Drag Reduction Of A 3d Bluff Body With A Blunt Base, Jarred Michael Pinn

Master's Theses

This thesis involves the experimental testing of a bluff body with a blunt base to evaluate the effectiveness of end-plate tabs in reducing drag. The bluff body is fitted with interchangeable end plates; one plate is flush with the rest of the exterior and the other plate has small tabs protruding perpendicularly into the flow. The body is tested in the Cal Poly 3ft x 4ft low speed wind tunnel. Testing is conducted in three phases.

The first phase was the hot-wire measurement of streamwise velocity of the near wake behind the bluff body. An IFA300 thermal anemometry system with …

Mechanical Integration Of A Versatile Air Suspension Into A Powered Wheelchair, Joel Michael Steinkraus

Master's Theses

Mechanical Integration of a Versatile Air Suspension into a Powered Wheelchair

Joel Steinkraus

It is undeniable that the vibration environment created by prolonged exposure to wheelchair use can cause discomfort for the rider and put him/her at risk of developing more severe medical conditions. While more research must be done to accurately quantify what constitues a harmful vibration environment, improved vibraiton isolation is an essential step. In order to incorporate structurally sound and effetive air suspension systems into motorized wheelchairs, a support structure is necessary. An after market wheelchair suspension system was designed, modeled, built and tested. Approximately 18 inches …

Bridge Design For Earthquake Fault Crossings – Synthesis Of Design Issues And Strategies, Osmar Rodriguez

Master's Theses

This research evaluates the seismic demands for a three-span curved bridge crossing fault-rupture zones. Two approximate procedures which have been proved adequate for ordinary straight bridges crossing fault-rupture zones, i.e., the fault-rupture response spectrum analysis (FR-RSA) procedure and the fault-rupture linear static analysis (FR-LSA) procedure, were considered in this investigation. These two procedures estimate the seismic demands by superposing the peak values of quasi-static and dynamic bridge responses. The peak quasi-static response in both methods is computed by nonlinear static analysis of the bridge under the ground displacement offset associated with fault-rupture. In FR-RSA and FR-LSA, the peak dynamic responses …

An Interactive Visualization Model For Analyzing Data Storage System Workloads, Steven Charubhat Pungdumri

Master's Theses

The performance of hard disks has become increasingly important as the volume of data storage increases. At the bottom level of large-scale storage networks is the hard disk. Despite the importance of hard drives in a storage network, it is often difficult to analyze the performance of hard disks due to the sheer size of the datasets seen by hard disks. Additionally, hard drive workloads can have several multi-dimensional characteristics, such as access time, queue depth and block-address space. The result is that hard drive workloads are extremely diverse and large, making extracting meaningful information from hard drive workloads very …

The Morphology Evolution And Voiding Of Solder Joints On Qfn Central Pads With A Ni/Au Finish, Julie Silk, Jianbiao Pan, Mike Powers

Industrial and Manufacturing Engineering

In this paper, we report on a comprehensive study regarding the morphology evolution and voiding of SnAgCu solder joints on the central pad of two different packages – QFN and an Agilent package called TOPS – on PCBs with a Ni/Au surface finish. Samples were isothermally aged at the equivalent of 0, 2, 7 and 14 years service life. Representative solder joints were cross-sectioned and analyzed using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX) in order to investigate the evolution of the solder joint morphology as a function of Au content and isothermal aging. IMC thickness was …

Dynamic Analysis Of A Lean Cell Under Uncertainty, Ahmed M. Deif

Industrial Technology and Packaging

One of the ultimate targets of lean manufacturing paradigm is to balance production and produce at takt time in production cells. This paper investigates the performance of a lean cell that implements the previous lean goals under uncertainty. The investigation is based on a system dynamics approach to model a dynamic lean cell. Backlog is used as a performance metric that reflects the cell’s responsiveness. The cell performance is compared under certain and uncertain external (demand) and internal (machine availability) conditions. Results showed that although lean cell is expected to be responsive to external demand with minimum waste, however, this …

The Design And Fabrication Of A Microfluidic Reactor For Synthesis Of Cadmium Selenide Quantum Dots Using Silicon And Glass Substrates, Peter Robert Gonsalves

Master's Theses

A microfluidic reactor for synthesizing cadmium selenide (CdSe) quantum dots (QDs) was synthesized out of a silicon wafer and Pyrex glass. Microfabrication techniques were used to etch channels into the silicon wafer. Holes were wet-drilled into the Pyrex glass using a diamond-tip drill bit. The Pyrex wafer was anodically bonded to the etched silicon wafer to enclose the microfluidic reactor. Conditions for anodic bonding were created by exposing the stacked substrates to 300V at ~350oC under 5.46N of force. A syringe containing a room temperature CdSe solution was interfaced to the microfluidic reactor by using Poly (dimethylsiloxane) (PDMS) as an …

Polar Field Oriented Control With 3rd Harmonic Injection, Martin Todd Hess

Master's Theses

Abstract

POLAR FIELD-ORIENTED CONTROL

with

3^RD HARMONIC INJECTION

Martin Todd Hess

Field Oriented Control (FOC), also known as vector control, is a widely used and well documented method for controlling Permanent-Magnet Synchronous Motors (PMSM) and induction motors. Almost invariably the orientation of the stator and rotor (field) fluxes are described in rectangular coordinates. In this thesis we explore the practicality of using polar coordinates.

Third harmonic injection is also a well-known technique that allows full utilization of the bus (DC-link), thus allowing the motor to run to full base speed without the use of field weakening. This technique potentially …

Pico-Satellite Integrated System Level Test Program, Marcus A. Ruddy

Master's Theses

Testing is an integral part of a satellite’s development, requirements verification and risk mitigation efforts. A robust test program serves to verify construction, integration and assembly workmanship, ensures component, subsystem and system level functionality and reduces risk of mission or capability loss on orbit.

The objective of this thesis was to develop a detailed test program for pico-satellites with a focus on the Cal Poly CubeSat architecture. The test program established a testing baseline from which other programs or users could tailor to meet their needs. Inclusive of the test program was a detailed decomposition of discrete and derived test …

Experimental Investigation Of Suction Slot Geometry On A Goldschmied Propulsor, Nicole M. Thomason

Master's Theses

The Goldschmied Propulsor concept combines boundary layer suction and boundary layer ingestion to improve propulsive efficiency and reduce drag on an axisymmetric body. This investigation of a Goldschmied Propulsor aimed to determine influential characteristics of the suction slot geometry to aid in better slot geometry design and to decrease the suction flow requirements for maintaining attached flow over the entire model surface. The Propulsor model was 38.5 inches in length with a max diameter of 13.5 inches. Three suction slot geometries were investigated with the addition of aluminum cusps to the slot entrance. The cusps varied in the distance they …

Design And Analysis Of A Reusable N2o-Cooled Aerospike Nozzle For Labscale Hybrid Rocket Motor Testing, Daniel Joseph Grieb

Master's Theses

A reusable oxidizer-cooled annular aerospike nozzle was designed for testing on a labscale PMMA-N₂0[1] hybrid rocket motor at Cal Poly-SLO.[2] The detailed design was based on the results of previous research involving cold-flow testing of annular aerospike nozzles and hot-flow testing of oxidizer-cooled converging-diverging nozzles. In the design, nitrous oxide is routed to the aerospike through a tube that runs up the middle of the combustion chamber. The solid fuel is arranged in an annular configuration, with a solid cylinder of fuel in the center of the combustion chamber and a hollow cylinder of fuel lining …

Dynamic Model Creation And Scripting Support In The Horizon Simulation Framework, Brian Jeffrey Butler

Master's Theses

Dynamic model creation and support for the Lua scripting language was added to the Horizon Simulation Framework used for the verification and validation of system-level requirements. The addition of scripting support allows for subsystem models and their algorithms to be defined using a simpler scripting language, rather than C++. The Luabind library by Rasterbind software is used to expose the C++ algorithms and classes to Lua that are already defined in the framework. Interoperability between Lua and C++ code allows for the ease of use of a scripting language while utilizing the utility classes and functions already created. The dynamic …