Engineering Commons^™

Design, Construction And Analysis Of An Ag Equipment Trailer, Connor Mckean

BioResource and Agricultural Engineering

No abstract provided.

Analysis Of Crop Dryer Recirculation And Heat Recuperation, Ross Ribeiro

BioResource and Agricultural Engineering

No abstract provided.

Evaluation, Installation, And Documentation Of Adcon Telemetry Stations Connected At Cal Poly, Shelsie Kloepper

BioResource and Agricultural Engineering

No abstract provided.

Design And Fabrication Of An Electric Aircraft Dolly, Kyler Zike

BioResource and Agricultural Engineering

No abstract provided.

Analysis Of Flap Gate Design And Implementations For Water Delivery Systems In California And Nevada, Kerilyn Ambrosini

BioResource and Agricultural Engineering

No abstract provided.

A Study On The Vibrational Performance Characteristics Of An E22 Isolator After Outgassing And Bake-Out, Alma Melendez

Master's Theses

The launch environment experiences many vibration, shock, and acoustic loads. A great concern is the high random vibration levels that can damage components and spacecraft structures, which can cause a mission failure. An effective method of reducing high frequency energy is using isolators. Overall, the need for vibration isolation has been increasing because there has been an increase in the use of mechanisms in which vibrations are prevalent. In addition, there has not been extensive research on the effects of isolators that are outgassed and cured. Therefore, it is important to investigate and understand the vibrational effects on isolators. It …

Smart Wall Outlet Design And Implementation For The Dc House Project, Kevin Roy Mendoza

Master's Theses

Most everyday AC appliances are designed to operate off of 120V coming from the wall outlet in our homes. This voltage is a standard set from our established infrastructure. Unlike AC devices, DC devices do not have any set standard of voltage they all will run off of. This presents a problem for the DC house as the various loads that will be used will have different required input voltages. One set voltage for a wall outlet will not suffice for the DC House. This Smart Wall Outlet is designed with a DC-DC converter that will have its output voltage …

A Frequency-Domain Method For Active Acoustic Cancellation Of Known Audio Sources, Ryan D. Rocha

Master's Theses

Active noise control (ANC) is a real-time process in which a system measures an external, unwanted sound source and produces a canceling waveform. The cancellation is due to destructive interference by a perfect copy of the received signal phase-shifted by 180 degrees. Existing active noise control systems process the incoming and outgoing audio on a sample-by-sample basis, requiring a high-speed digital signal processor (DSP) and analog-to-digital converters (ADCs) with strict timing requirements on the order of tens of microseconds. These timing requirements determine the maximum sample rate and bit size as well as the maximum attenuation that the system can …

Water And Nutrient Recycling In High Rate Algae Ponds Fed In Primary Treated Municipal Wastewater, Michael Field Chang

Master's Theses

Algal biofuels present a promising future alternative to petroleum based fuels. Water nutrient recycling is a key step to increase the sustainability of algae biofuel production facilities. This thesis discusses the process of nutrient and water recycling in high rate algae raceway ponds (HRAP) fed primary treated municipal wastewater. Research was conducted primarily at the San Luis Obispo Water Resource Reclamation Facility (SLOWRRF). Nine 30 m², 0.3 m deep HRAP’s were operated continuously from June 1, 2013 to April 17, 2014. The ponds were arranged in three sets of triplicate ponds, with two pond sets run on 3-day …

Pump Station Calculations And Irrigation System Evaluation For Trestle Vineyard, Linda Bushey

BioResource and Agricultural Engineering

No abstract provided.

Design, Testing, And Development Of An Internal Combustion Engine Throttle Controller, Michael Burlingame

BioResource and Agricultural Engineering

No abstract provided.

Crotale Sample Library, Ryan Waczek

Music

This report will discuss the process of creating a digital sample based library for musical applications. Topics such as recording, microphone placement, and mixing will be addressed; as well as elements of design in Adobe Photoshop, and computer scripting in the language of the computer program Komplete 5 by Native Instruments. The instrument sampled is the crotales, an orchestral, melodic percussion instrument.

Smooth Muscle Cell Organization In The Stem Region Of The Gracilis Collateral Circulation, Amanda Krall

Biomedical Engineering

Many patients who suffer from the ischemic Peripheral Arterial Occlusive Disease (PAOD) experience intermittent claudication, which can be attributed to impaired vasodilation. Collateral vessels are the primary site of resistance to blood flow downstream; therefore maximizing vasodilation in collaterals is crucial for efficient circulation. Collaterals function as natural bypasses around the occluded arteries and the increase in flow into these vessels causes them to outwardly remodel into conduit vessels. However, functional vasodilation in the stem region of collateral vessels is impaired at day 7 following femoral ligation, which can be attributed to smooth muscle cell malfunction. However, the increase in …

Robotic Book Scanner, Tobias Samuel Elder, Cynthia Marie Wong

Computer Engineering

Digitizing books has been an issue tackled by companies to allow people to read off Kindles and iPads rather than the traditional paperback. Companies like Google have spent more than $1000 on machines to convert books into electronic copies readable on devices. Yet, not much effort has been made into the invention of an automatic book scanner for consumers. This project seeks to determine a cost-effective approach to robotic book scanning to create PDFs from physical books. This project serves as a proof of concept for a reasonably priced automatic book scanner accessible to consumers. Potentially, the device may be …

Chromium Os On Freescale I.Mx6q, Pushpal Sidhu

Computer Engineering

This projects intention is to get Chromium OS running on a Freescale i.MX6q processor, a processor based on the ARM® Cortex™-A9 architecture. The development board I used is the Ventana GW5400 by Gateworks. This project inherently meant using Chromium OS's development system which meant I created a board specific package for the Ventana single board computer. This project is a proof of concept that can mean extending Chromium OS to various implementations of the ARM® Cortex™-A9 architecture.

St. Jude Medical - R&D Robot For Sensor Testing, Andrew Chanul Kim, Stanley Logan Laszczyk, Edgar Nava, Nathan Gall

Electrical Engineering

No abstract provided.

Rapid Battery Exchange Safety And Sensing, Ben John Froelich, Isaac Sungjin Kim

Electrical Engineering

The Rapid Battery Exchange system (RBX) swaps batteries in an electric van, allowing almost continuous operation of the vehicle. The RBX system is designed and built by The Cal Poly Electric Vehicle Engineering Club (EVEC). The system includes the exchange ramp, two battery packs, and the electric “G-Van.” While the vehicle drives using one of the battery packs, the other pack charges in the exchange ramp. When the van’s battery depletes, it drives onto the ramp and swaps the dead battery for the charged one, and the process repeats.

The RBX battery pack safety and sensing project divides into two …

Battery Management System, Michael Desando, Kyle Woody

Electrical Engineering

Problem Statement:

There have been recent reports of multi-million dollar companies having to recall entire projects due to their BMS’s malfunctioning or operating incorrectly. The purpose of this project is to analyze the future of batteries, the Lithium-Ion cell, and to exercise a BMS to better understand its capabilities and possible cases for errors. Lithium ion batteries are intolerant of overcharge and overdischarge. Abuse of this kind can result in high temperatures, venting of gases, fire, or explosion. Therefore battery management systems have been devised to prevent such abuse. Recent events such as fires on the Boeing Dreamliner and the …

Low Voltage Cmos Sar Adc Design, Ryan Hunt

Electrical Engineering

This project centers on the design of a single ended 10-bit successive approximation register analog to digital converter (SAR ADC for short) that easily interfaces to a micro-controller, such as an Arduino. With micro-controller interfacing in mind, the universal data transfer technique of SPI proved an easy way to communicate between the ADC and the micro-controller. The ADC has a range of 1V (highest code value) to 0V (lowest code value) and operates from a single voltage rail value of 1.8V. Typical SPI clock speeds run on the order of 2MHz and with a 10-bit ADC this means a sampling …

Wind And Ventilation Turbine (Wvt) Generator, Anthony Lloyd, Jacob Michener

Electrical Engineering

This project aims to create a more compact and accessible renewable energy source using the Wind and Ventilation Turbine (WVT) Generator. The wind turbine provides ventilation while generating “clean” electricity using solar and kinetic energy. The electrical generation causes no functional losses to the ventilation as rising heat and passing wind turn the turbine, ventilating the house. Placing a generator beneath the spinning turbine allows for the transformation of mechanical motion into electrical energy. The system charges a battery, supplying recharging power into small standard electronics (i.e. cell phones, tablets, etc.) through a USB output.

Analog Violin Audio Synthesizer, Brandon E. Davis

Electrical Engineering

Abstract In the past decade, music electronics have almost completely shifted from analog to digital technology. Digital keyboards and effects provide more sound capabilities than their analog predecessors, while also reducing size and cost. However, many musicians still prefer analog instruments due to the perception that they produce superior sound quality. Many musicians spend extra money and accommodate the extra space required for analog technologies instead of digital.

Furthermore, audio synthesizers are commonly controlled with the standard piano keyboard interface. Many musicians can perform sufficiently on a keyboard, but requiring a specific skill set limits the size of the market …

Buck-Boost Dc-Dc Converter With Input Protection System For The Energy Harvesting From Exercise Machines Project, Byungjae David Yoo, Sheldon Tyler Kong Ming Chu

Electrical Engineering

Cal Poly’s Energy Harvesting from Exercise Machines (EHFEM) project comprises of multiple subprojects seeking to effectively create a sustainable energy source through harvesting electrical energy generated from physical exercise machines. This project designs and implements a Buck-Boost DC-DC converter using a LT3791-1 4-Switch Buck-Boost Controller, replacing the previous SEPIC design. The DC-DC converter must operate within limits set by the maximum input range of the LT3791-1 controller. An input protection system prevents inputs higher than rated values, which may adversely damage the Buck-Boost DC-DC converter. These inputs include overvoltage transients, average voltage, and current output by the Precor EFX 561i …

Real Time Swim Instructor, Konrad Antoniuk

Electrical Engineering

Both competitive and recreational swimmers want an efficient swim stroke but often lack consistent feedback with technical insight. Competitive swimmers rely on coaches for instruction but have to stop swimming to listen. The Real Time Swim Instructor project provides live feedback to a swimmer so they can feel their stroke correction while they’re swimming. The developing swimmer feels the difference between correct and incorrect form instantaneously.

The project takes on the responsibility of measuring the moving body, accurately determining stroke improvement, functioning under water, and providing recognizable feedback. Additionally, the user can review their swim from data stored in memory. …

Formula Sae Cooling System Design, Lisa Van Den Berg, Brandon Lofaro

Mechanical Engineering

The overall objective of this senior project is to develop, via testing and analysis, a guided process that will aid the Cal Poly Formula SAE team in designing their cooling system. More specifically, a set of designed tests will yield the results necessary in determining a combination of fan and radiator that will achieve appropriate cooling.

A test section that has the capability of interfacing with both the wind tunnel in the Thermal Science Lab and a radiator will be used to facilitate the necessary experiments. The wind tunnel is powered by fan controlled by a variable frequency drive that …

Formula Sae Hybrid Carbon Fiber Monocoque / Steel Tube Frame Chassis, Matthew Hagan, John Rappolt, John Waldrop

Mechanical Engineering

The Cal Poly Formula SAE Team created this project in order to design and fabricate a high-performance chassis which would be competitive at 2013 FSAE Lincoln, and to document the process so that future teams could more easily create a chassis. One of the main goals was to reduce weight from the 143- lb 2012 chassis subsystem. A weight of 95 lb was achieved, with 82 lb in the chassis structure itself and a predicted torsional stiffness of 1700 lb*ft/deg. Composite materials design and manufacturing techniques were developed during the project. Design, testing, and manufacturing processes are detailed, and results …

Horned Lark Management For The Protection Of Lettuce Sprouts, Taylor Wetzel, Eduardo Morales, Kyle Suguitan

Mechanical Engineering

The following document is the Final Project Report. Following the Critical Design Report, the top idea was taken and modified once again to suit the needs of the sponsor. Details regarding the changes are outlined throughout Chapter 3.

The provided background section explains why there is a need for a new device at Tanimura and Antle that will suit the customer's needs better than current methods and existing products. The top ideas picked for the Conceptual Design Review are the presented to reiterate the problems that were depicted in them and why they were not selected as part of the …

Low-Cost Strider For Guatemala, Nicole Catherine Cooper, Gonzalo Hernandez, Jared W. Tower

Mechanical Engineering

The purpose of this project was to create a strider, a type of standing rehabilitation device, for children in developing countries who have trouble walking and supporting their full body weight. The project was initially brought to us by Cal Poly professor Brian Self, who had visited a clinic in San Marcos and determined that there were children there who had difficulties with walking and were a need for a rehabilitation device. The team discussed the problem with Dr. Self, Matt Robinson (a local San Luis Obispo prosthetist), and Cal Poly physics professor Pete Schwartz, all of whom had visited …

Energy Generator Exploration Station Senior Project Report, Evan Carr, Christopher Scharff, Andrea Govea

Mechanical Engineering

The mission of Team EnGen is to create a safe and reliable, human powered energy generation system for the Exploration Station. This project was proposed by the Exploration Station in response to a grant received by Pacific Gas and Electric (PG&E) that allocated funds for an energy conservation exhibit. This system will take the form of a model energy truck and a darkened neighborhood display that the user powers through peddling, turning the generator to create the electricity that will light up the display. The Exploration Station and Team EnGen agree that this style of design is accessible to all …

2d Wireform Process Improvement, Katy Conlin, Carlo Ebora, Jordan Gamble

Mechanical Engineering

The body of this work has been created for Edwards Lifesciences in conjunction with senior project requirements. As such, the information produced and contained within is under a non‐disclosure agreement. As per request by sponsor, the body of the work will not be submitted to any outside parties, and the title page will serve as proof of completion.

Automated Foosball Table, Jim R. Stefani, Alex J. Herpy, Brett Gordon Jaeger, Kevin S. Haydon, Derek Alan Hamel

Mechanical Engineering

This project is the second iteration of an automated foosball table for Yaskawa America as a trade show display. The table is meant to provide an interactive experience which highlights the speed and precision of the Yaskawa hardware. The first iteration of the project was mainly focused on creating the physical hardware for the system and to begin the basic programming for the system. This phase of the project was focused on finalizing the physical hardware of the system, implementing the vision system and to continue the basic programing of the system AI. A third team will be assigned to …