Engineering Commons^™

Avoided Water Cost Of Electricity Generation For Solar Pv And Wind Technologies In Southern California, Matthew Cohen

Master's Theses

The objective of this thesis is to provide a foundation for evaluating the water costs associated with electricity production to calculate the avoided water cost of energy for solar PV and wind technologies relative to coal, natural gas, nuclear, geothermal, concentrated solar thermal, and biomass. Water consumption is estimated for energy production (fuel extraction and preparation) and electricity generation (power plant operation) using the best available information from published articles. The quantity of water consumed for electricity production is monetized for a Southern California case study based on the water rates of Metropolitan Water District of Southern California (MET), which …

Hil Simulation For Smartphone-Guided Autonomous Systems, Matthew Gerdt

Computer Engineering

My bachelor thesis focuses on implementing a Hardware in the Loop (HIL) simulation for a quadcopter controlled by an Android smartphone. The HIL simulation will be able to test the software running on an Android smartphone by simulating a virtual quadcopter on the computer without the need to use an actual quadcopter. To accomplish this I will have to modify my team’s existing simulation to allow for the communication between the smartphone and simulation. At the completion of my work the HIL simulation will allow the testing of different aspects of the Android application, such as the tracking of an …

Investigating Hemodynamic Responses To Electrical Neurostimulation, Sean Youra

Master's Theses

Since the 1900s, the number of deaths attributable to cardiovascular disease has steadily risen. With the advent of antihypertensive drugs and non-invasive surgical procedures, such as intravascular stenting, these numbers have begun to level off. Despite this trend, the number of patients diagnosed with some form of cardiovascular disease has only increased. By 2030, prevalence of coronary heart disease is expected to increase approximately by 18% in the United States. By 2050, prevalence of peripheral arterial occlusive disease is expected to increase approximately by 98% in the U.S. No single drug or surgical intervention offers a complete solution to these …

A Rubric For Electrochemical Testing Of Metallic Biomaterials, Frederick G. De La Fuente

Master's Theses

Corrosion is a major factor for the failure of metallic medical implants. Testing a metal’s suseptability to corrosion prior to implantation is key to a successful implantation. Electrochemical processes were used in this study to evaluate the characteristics of corrosion of both AISI 316 stainless steel and titanium alloy Ti6Al4V, welded and non-welded. Linear, potentiodynamic, and cyclic polarization curves were produced by the PARC 2273 potentiostat showing the corrosion tendencies of the metals in four unique solutions 3.5% NaCl, 0.35% NaCl, phosphate buffered saline solution (PBS), and Butterfield phosphate buffered solution (BPS). The concentration of chloride ions in solutions affected …

Effect Of Adaptive Tabs On Drag Of A Square-Base Bluff Body, Brian W. Barker

Master's Theses

This thesis involves the experimental wind tunnel testing of a 0.127m by 0.127m square-base bluff body to test the effectiveness of trailing edge tabulations to reduce drag in the Cal Poly 0.912m by 1.219 m low-speed wind tunnel. To accomplish this, the boundary layer was first measured on the trailing edge of the model for the three speeds at 10, 20, and 30 m/s, with Re = 8.3e4, 1.6e5 and 2.5e5 respectively, without the tabs. Three different tests were performed to determine the effectiveness of the tabs. These tests included base pressure measurements, total drag force measurements and hotwire velocity …

Design, Characterization And Application Of A Multiple Input Stethoscope Apparatus, Spencer Geng Wong

Master's Theses

For this project, the design, implementation, characterization, calibration and possible applications of a multiple transducer stethoscope apparatus were investigated. The multi-transducer sensor array design consists of five standard stethoscope diaphragms mounted to a rigid frame for a-priori knowledge of their relative spatial locations in the x-y plane, with compliant z-direction positioning to ensure good contact and pressure against the subject’s skin for reliable acoustic coupling. When this apparatus is properly placed on the body, it can digitally capture the same important body sounds investigated with standard acoustic stethoscopes; especially heart sounds. Acoustic signal inputs from each diaphragm are converted to …

Experimental Investigation Of Active Wingtip Vortex Control Using Synthetic Jet Actuators, Peter J. Sudak

Master's Theses

An experiment was performed in the Cal Poly Mechanical Engineering 2x2 ft wind tunnel to quantify the effect of spanwise synthetic jet actuation (SJA) on the drag of a NACA 0015 semispan wing. The wing, which was designed and manufactured for this experiment, has an aspect ratio of 4.20, a span of 0.427 m (16.813”), and is built around an internal array of piezoelectric actuators, which work in series to create a synthetic jet that emanates from the wingtip in the spanwise direction. Direct lift and drag measurements were taken at a Reynolds Number of 100,000 and 200,000 using a …

Transonic And Supersonic Ground Effect Aerodynamics, Graham Doig

Aerospace Engineering

A review of recent and historical work in the field of transonic and supersonic ground effect aerodynamics has been conducted, focussing on applied research on wings and aircraft, present and future ground transportation, projectiles, rocket sleds and other related bodies which travel in close ground proximity in the compressible regime. Methods for ground testing are described and evaluated, noting that wind tunnel testing is best performed with a symmetry model in the absence of a moving ground; sled or rail testing is ultimately preferable, though considerably more expensive. Findings are reported on shock-related ground influence on aerodynamic forces and moments …

Microvascular Topology And Intravascular Endothelial Cell Labeling In The Gracilis Anterior Muscle Of Balb/C Mice, Paul Heckler Ii

Biomedical Engineering

Peripheral arterial occlusive disease (PAOD) affects approximately 200 million individuals globally. The major underlying cause of PAOD is an inflammatory disease known as atherosclerosis, which results from the build-up of low-density lipoproteins (LDL) in the sub-intimal space. This initiates a complex cascade of events that lead to plaque growth. Plaque growth can then expand into the lumen of the vessel and result in occlusion and/or thrombosis. Symptoms of the disease can include claudication, ulcers, and/or gangrene, although many patients are asymptomatic. Similar to other forms of ischemic disease, risk factors for PAOD include hypertension, diabetes, and smoking. Common treatments include …

Interfacial Interactions Between Carbon Nanoparticles And Conjugated Polymers, Yanqi Luo

Master's Theses

Conjugated polymer based electronics, a type of flexible electronic devices, can be produced from solution by traditional printing and coating processes in a roll-to-roll format such as papers and graphic films. This shows great promise for the emerging energy generation and conversion. The device performance of polymer electronics is largely dependent of crystalline structures and morphology of photoactive layers. However, the solution crystallization kinetics of conjugated polymers in the presence of electron acceptor nanoparticles has not been fully understood yet. In this study, solution crystallization kinetics of poly (3-hexylthiophene) in the presence of carbon nanotubes and graphene oxide has been …

Nerve Fiber Diameter Measurements Using Hematoxylin And Eosin Staining And Brightfield Microscopy To Assess The Novel Method Of Characterizing Peripheral Nerve Fiber Distributions By Group Delay, Jorge Arturo Vazquez

Master's Theses

Peripheral neuropathies are a set of common diseases that affect the peripheral nervous system, causing damage to vital connections between various parts of the body and the brain and spinal cord. Different clinical conditions are known to selectively impact various size nerve fibers, which often makes it difficult to diagnose which peripheral neuropathy a patient might have. The nerve conduction velocity diagnostic test provides clinically useful information in the diagnosis of some peripheral neuropathies. This method is advantageous because it tends to be minimally invasive yet it provides valuable diagnostic information. However, this test does not determine characteristics of peripheral …

Treatment Of Nitrogen Oxides By Chlorella Vulgaris Algae In Photobioreactors, Steven Shihady

Master's Theses

The effectiveness of algae to treat NO₂and NO in simulated flue gas was tested using Chlorella vulgaris in photobioreactors (PBRs) using NO_xconcentrations between 30 ppm to 780 ppm. NO_xdissolved and reacted in water to form NO₃^-and NO₂^-in the PBR growth medium, providing a nitrogen source that the algae readily assimilated for cell synthesis. Three 20-L photobioreactors were inoculated with a pure culture of C. vulgaris prepared in Bristol growth medium and algae were grown in the PBRs at 25°C and pH of 7.0 in a modified Bristol medium …

Stereo Vision System Module For Low-Cost Fpgas For Autonomous Mobile Robots, Connor Citron

Master's Theses

Stereo vision uses two adjacent cameras to create a 3D image of the world. A depth map can be created by comparing the offset of the corresponding pixels from the two cameras. However, for real-time stereo vision, the image data needs to be processed at a reasonable frame rate. Real-time stereo vision allows for mobile robots to more easily navigate terrain and interact with objects by providing both the images from the cameras and the depth of the objects. Fortunately, the image processing can be parallelized in order to increase the processing speed. Field-programmable gate arrays (FPGAs) are highly parallelizable …

Development And Use Of Moisture-Suction Relationships For Geosynthetic Clay Liners, Jacob Law Risken

Master's Theses

A laboratory test program was conducted to determine the moisture-suction relationships of geosynthetic clay liners (GCLs). Moisture-suction relationships were determined by combining suction data from pressure plate tests, contact filter paper tests, and relative humidity tests, then fitting water retention curves (WRCs) to the data. WRCs were determined for wetting processes and drying processes in terms of gravimetric moisture content and volumetric moisture content.

The effects of GCL type, hydration solution, wet-dry cycles, and temperature on the moisture-suction relationships were analyzed. The three GCLs of the test program consisted of configurations of woven and nonwoven geotextiles reinforced with needlepunched fibers. …

Organic-Based Microwave Frequency Absorbers Using Corn Stover, Ben Smythe, Sean Casserly, Dean Arakaki

Electrical Engineering

Commercial antenna test chambers (anechoic) currently use polyurethane foam absorbers on chamber interiors to eliminate undesired radio-frequency (RF) reflections. While effectively absorbing microwave signals, polyurethane material particulates over time adding contaminants to clean rooms and reducing absorber lifetime. These absorbers also release toxic gas when operating under high temperatures and pose a health risk to direct-contact personnel. This paper presents reflectivity analysis and performance of alternative organic-based (corn stover) microwave frequency absorbers for use in anechoic chambers. These absorbers are composed of renewable materials and eliminate the toxic gas release problem for polyurethane materials under high power test conditions. Preliminary …

Multi-Technique Broadband Microstrip Patch Antenna Design, Daniel Colles, Dean Arakaki

Electrical Engineering

Microstrip patch antennas offer low profile and small footprint advantages, but limited operating bandwidth. Substantial research focuses on broadband techniques. This paper presents the design, simulation, fabrication, and characterization of a 30% bandwidth microstrip patch antenna that incorporates multiple broadband techniques while minimizing footprint area. Methods include patch shape, dielectric thickness, and coupling slot optimization, with capacitively-coupled L-probe feeds. The final design incorporates an electrically thick dielectric and circular-E patch geometry. Microstrip L-probe feed and coupling slot dimensions were optimized via HFSS simulations. The final design was fabricated, and then tested in an anechoic chamber. The new design has measured …

Development Of A Public Education Website: Building Bridges Over Water, Angelina Mckee

Agricultural Education and Communication

Website created by Angelina McKee to educate the public about water resource issues. Water is the basic unit of life, water resources are the basis for what societies and ecosystems are founded upon. Water shortages and droughts are more prevalent in our ever-changing world. It is no shock that there are discrepancies between various stockholders on either sides of the dry riverbed. This senior project resulted in the development of a website that addresses global water resources, water use in California, water conservation, and water allocation. The website informs the public on water resources and related issues and will hopefully …

Grid-Scale Energy Storage: A Proposed Control Algorithm For Sodium Sulfur Batteries, Daniel Spaizman

Master's Theses

With carbon dioxide levels in our atmosphere reaching record highs and 2020 quickly approaching, California is expected to pave the way for the United States in terms of replacing fossil fuel generation facilities with various renewable energy power plants. It is well documented that the inherent variability and limited duty cycle of renewables has hindered their growth. Energy storage technologies represent the bridge that can help us cross the divide from where we stand to where we must stand in the next 6 years. Utility companies value services such as peak shaving, voltage support, and frequency regulation, all of which …

Synthesis And Characterization Of Cdse/Zns Core/Shell Quantum Dot Sensitized Pcpdtbt-P3ht:Pcbm Organic Photovoltaics, Buddy J. Bump

Master's Theses

Durable, cheap, and lightweight polymer based solar cells are needed, if simply to meet the demand for decentralized electrical power production in traditionally “off-grid” areas. Using a blend of Poly(3-hexylthiophene-2,5-diyl) (P3HT), Phenyl-C61-butyric acid methyl ester (PCBM), and the low band-gap polymer Poly[2,6-(4,4-bis-(2- ethylhexyl)-4H-cyclopenta [2,1-b;3,4-b′]dithiophene)-alt-4,7(2,1,3-benzothiadiazole)] (PCPDTBT), we have fabricated devices with a wide spectral response and 3% power conversion efficiency in AM 1.5 conditions; however, this thin film system exhibits only 0.43 optical density at 500 nm. To improve the performance of this polymer blend photovoltaic, we aim to increase absorption by adding CdSe(ZnS) core (shell) quantum dots. Four groups of …

Cost Performance Dynamics In Lean Production Leveling, Ahmed Deif, Hoda Elmaraghy

Industrial Technology and Packaging

Balancing of production systems is one of the main lean manufacturing principles as it reduces in-process storage and related forms of waste. A dynamic systems approach is proposed to investigate challenges of implementing production leveling and associated costs. A lean cell producing at takt time is modeled using system dynamics. The model captures various lean tools influencing production leveling and their implications. Comparative cost analysis between various leveling implementation policies for stochastic demand with multiple products is conducted. Results showed that determining the most feasible leveling policy is highly dictated by both the cost and limitations of capacity scalability. In …

Viscosity Dependence Of Faraday Wave Formation Thresholds, Lisa M. Slaughter

Symposium

This experiment uses an electromagnetic shaker to produce standing wave patterns on the surface of a vertically oscillating sample of silicon liquid. These surface waves, known as Faraday waves, form shapes such as squares, lines, and hexagons. They are known to be dependent upon the frequency and amplitude of the forcing as well as on the viscosity and depth of the liquid in the dish. At a depth of 4mm and for various silicon liquids having kinematic viscosities of 10, 20, and 38 cSt, we determined the acceleration at which patterns form for frequencies between 10 and 60 Hz. For …

Beehive Monitor, Tyler William Lewis

Computer Engineering

No abstract provided.

Talk Vox, Javier Thiele-Ruiz

Computer Engineering

No abstract provided.

Influence Of Grain Size And Widmanstätten Colonies On Variability Of Tensile Properties Of Forged Ti-6al-4v, Blake T. Gaspar

Master's Theses

When testing forgings for specifications, it was found that some parts did not meet the requirements for mechanical properties. This triggered an investigation into two of the parts from the lot that did not meet specification. The ultimate reason for failure was due to lower than necessary yield strength and ultimate tensile strength values, as well as unwanted variability between regions of the part. Therefore, samples of the regions were tensile tested to determine the differences that existed in yield strength, ultimate tensile strength, and elongation. After tensile testing, quantitative metallography and fractography were conducted to identify aspects of the …

An Investigation Into The Properties And Fabrication Methods Of Thermoplastic Composites, Ann E. Livingston-Peters

Master's Theses

As applications for thermoplastic composites increase, the understanding of their properties become more important. Fabrication methods for thermoplastic composites continually improve to match designs specifications. These advanced thermoplastics have begun to show an improvement in mechanical properties over those found in thermoset composites commonly used in industry. Polyaryletherketones (PEK) have high service temperatures, good mechanical properties, and improved processing capabilities compared to thermoplastics used in the past making them important to the aerospace industry. The wide range of types of PEK make them suitable for a variety of applications, but selection of specific chemistries, processing parameters, and composite stack-ups determine …

Developent Of A Phospholipid Encapsulation Process For Quantum Dots To Be Used In Biologic Applications, Logan Grimes

Master's Theses

The American Cancer Society predicts that 1,665,540 people will be diagnosed with cancer, and 585,720 people will die from cancer in 2014. One of the most common types of cancer in the United States is skin cancer. Melanoma alone is predicted to account for 10,000 of the cancer related deaths in 2014. As a highly mobile and aggressive form of cancer, melanoma is difficult to fight once it has metastasized through the body. Early detection in such varieties of cancer is critical in improving survival rates in afflicted patients. Present methods of detection rely on visual examination of suspicious regions …

Design, Implementation, And Test Of A Micro Force Displacement System, Evan Derek Cate

Master's Theses

The design and implementation of a micro-force displacement system was completed to test the force-displacement characteristics of square silicon diaphragms with side lengths of 4mm, 5mm, and 7mm with a thickness of 10um. The system utilizes a World Precision Instruments Fort 10g force transducer attached to a World Precession Instruments TBM4M amplifier. A Keithley 2400 source meter provided data acquisition of the force component of the system. A micro prober tip was utilized as the testing probe attached to the force transducer with a tip radius of 5um. The displacement of samples was measured using a Newport M433 linear stage …

Second Generation Design Of An Operator Independent Teflon Coating Adhesion Tester For Coronary Guidewires, Garrett L. Wong

Materials Engineering

No abstract provided.

Electrochemical Characterization Of Precious Metal Braze Alloys Using Potentiodynamic Polarization, Maxwell Glen Martin, Mason Gregory Morgan, Matthew David Vance

Materials Engineering

This study aimed to characterize the electrochemical behavior of six precious metal braze alloys by performing potentiodynamic polarization tests (ParStat 2273) based on ASTM Specifications G5 and G59. To determine the extent to which the alloys will contribute to galvanic corrosion in a marine environment (3.5 wt% NaCl), corrosion analysis software was used to produce fitted Tafel lines to determine the open circuit potential, V_oc, for each alloy. The V_oc values for the alloys were found to be -66.58 mV for Gold ABA, 13.01 mV for Nicoro^®, -39.00 mV for Nioro^®, 23.4 mV …

Fire Protection And Life Safety Evaluation- Houston Community College- San Jacinto Building, Will Clay

Fire Protection Engineering: Culminating Experience Project Reports

This report evaluates the life safety features of the HCC San Jacinto Building (SJB) both prescriptively and on a performance basis. The goal is to present the building code requirements for the HCC San Jacinto building and determine if the design is in compliance, as well as analyze the building on the basis of performance criteria to determine if there are any excessive threats to life safety. The building is designed in compliance with the Houston Building Code, and takes advantage of lesser requirements for existing features. The performance section determines that based on fire and egress modeling, that while …