Engineering Commons^™

Field Emissions Of Methane And Nitrous Oxide From California Landfills, Alexandra D. Limpert

Master's Theses

Comprehensive and systematic aerial and field investigations were conducted at representative California landfills to quantify emissions of methane and nitrous oxide. Landfills are highly engineered; however, they are one of the largest anthropogenic sources of greenhouse gases, causing human health and safety concerns. Methane (CH₄) and nitrous oxide (N₂O) are significant greenhouse gases with high global warming potentials that are generated in a landfill environment.

For site selection, sites were evaluated based on waste in place, climate zone, faults and oil and gas operations, population density, cover conditions and percentage of cover types, age of waste, …

Fifth Aeon – A.I Competition And Balancer, William M. Ritson

Master's Theses

Collectible Card Games (CCG) are one of the most popular types of games in both digital and physical space. Despite their popularity, there is a great deal of room for exploration into the application of artificial intelligence in order to enhance CCG gameplay and development. This paper presents Fifth Aeon a novel and open source CCG built to run in browsers and two A.I applications built upon Fifth Aeon. The first application is an artificial intelligence competition run on the Fifth Aeon game. The second is an automatic balancing system capable of helping a designer create new cards that do …

Study Of Paper Microbial Fuel Cells For Use In On-Site Wastewater Testing, William A. Tolmasoff

Master's Theses

This study demonstrated a technique for fabricating simple, low-cost Paper Microbial fuel cells (PMFC’s) in the model of a previous study to, for the first time, produce voltage from wastewater effluent. The PMFC’s were created by stacking and gluing the main components of an MFC together: reservoir layer; anode; cation exchange membrane (CEM); air cathode. A wax printer was used to create the hydrophobic borders of the PMFC’s on filter paper, and graphite paint was applied to the paper to create the anode. The CEM’s considered were filter paper, wax, and Nafion, with Nafion being the most efficient. Finally, the …

Analysis Of The Effects Of Adaptive Ramp Metering On Measures Of Efficiency With A Proposed Framework For Safety Evaluation, Jacky Loh

Master's Theses

Adaptive ramp metering (ARM) is a widely popular intelligent transportation system (ITS) tool that boasts the ability to reduce congestion and streamline traffic flow during peak hour periods while maintaining a lower implementation cost than traditional methods such as freeway widening. This thesis explores the effectiveness of ARM implementation on an 18 mile segment of the Interstate 80 (I-80) corridor in the Bay Area residing in northern California. Smaller segments of this particular segment were analyzed to determine the effective length of ARM on efficiency at various lengths originating from a known bottleneck location. Efficiency values were also compared against …

Effects Of Corrugations On Stiffness Properties Of Composite Beams For Structural Applications, Jane Xiao

Master's Theses

Composites have high strength-to-weight ratios, which is particularly desired for applications with weight restrictions. Common composite materials such as carbon fiber reinforced plastic (CF) and fiber glass reinforced plastic (FG) were used in this research. While composite materials possess high stiffness and strength properties, the stiffness of composite laminates may be maximized by changing the geometry. By adding corrugations, the flexural stiffness is increased in one direction compared to the stiffness of a flat part with the same amount of material. Thus, stiffness increases without a change in weight. The primary goal of this research was to investigate the stiffness …

Atomic Oxygen Effects On Particulate Contamination And Short Beam Strength Of Carbon Composites, Marlee K. Litzinger

Master's Theses

In order to design a successful space system, the unique challenges of the space environment it will operate in must be considered during the design process. Atomic oxygen (AO) is a detrimental environmental effect found in Low Earth Orbit (LEO) that affects spacecraft surfaces by oxidizing and eroding material over time, particularly polymers. Carbon fiber/epoxy composites are a commonly used spacecraft material affected by AO exposure. Carbon composites are used as a structural material, such as on solar panels; their large surface area therefore is a potential contamination source to sensitive components. The Space Environments and Testing Lab at California …

Carbonate Chemistry Characterization In A Low-Inflow Estuary With Recent Seagrass Loss, Jolie Higgins

Master's Theses

Estuaries are dynamic environments that are strongly affected by natural variability, as well as direct and indirect anthropogenic impacts. A better understanding of the drivers of carbon fluxes and biogeochemical variability in estuarine systems is needed, particularly with the increasing threat of ocean acidification. Morro Bay in Central California is a small nationally protected estuary, with seasonally low freshwater inputs. Since 2007, the bay has experienced a significant loss of native seagrass, Zostera marina, which is an important component of the marine ecosystem. Because seagrass photosynthesis decreases carbon dioxide and increases oxygen in the water column, the loss of seagrass …

A Predictive Modeling Approach For Assessing Seismic Soil Liquefaction Potential Using Cpt Data, Jonathan Paul Schmidt

Master's Theses

Soil liquefaction, or loss of strength due to excess pore water pressures generated during dynamic loading, is a main cause of damage during earthquakes. When a soil liquefies (referred to as triggering), it may lose its ability to support overlying structures, deform vertically or laterally, or cause buoyant uplift of buried utilities. Empirical liquefaction models, used to predict liquefaction potential based upon in-situ soil index property measurements and anticipated level of seismic loading, are the standard of practice for assessing liquefaction triggering. However, many current models do not incorporate predictor variable uncertainty or do so in a limited fashion. Additionally, …

Designing A Simulator For An Electrically-Pumped Organic Laser Diode, Robert Hulbert

Master's Theses

Organic semiconductors provide an alternative set of basis materials to fabricate electronic devices like PN Junctions, LEDs, and FETs. These materials have several benefits over traditional inorganic semiconductors including their mechanical flexibility, reliance on renewable resources, and inexpensive large-scale manufacturability. Despite the contemporary device implementations with organic semiconductors, a solid-state electrically-pumped organic laser diode does not exist. However, organically-based lasers do exist by utilizing the organic material strictly for optical gain. The challenge occurs when charge carriers appear in the organic material. The charge carriers must reach a concentration such that population inversion occurs producing optical gain. However, between the …

A Homegrown Dsmc-Pic Model For Electric Propulsion, Dominic Charles Lunde

Master's Theses

Powering spacecraft with electric propulsion is becoming more common, especially in CubeSat-class satellites. On account of the risk of spacecraft interactions, it is important to have robust analysis and modeling tools of electric propulsion engines, particularly of the plasma plume. The Navier-Stokes equations used in classic continuum computational fluid dynamics do not apply to the rarefied plasma, and therefore another method must be used to model the flow. A good solution is to use the DSMC method, which uses a combination of particle modeling and statistical methods for modeling the simulated molecules. A DSMC simulation known as SINATRA has been …

A 3-Dimensional In Silico Test Bed For Radiofrequency Ablation Catheter Design Evaluation And Optimization, Carolyn Teng

Master's Theses

Atrial fibrillation (AF) is the disordered activation of the atrial myocardium, which is a major cause of stroke. Currently, the most effective, minimally traumatic treatment for AF is percutaneous catheter ablation to isolate arrhythmogenic areas from the rest of the atrium. The standard in vitro evaluation of ablation catheters through lesion studies is a resource intensive effort due to tissue variability and visual measurement methods, necessitating large sample sizes and multiple prototype builds. A computational test bed for ablation catheter evaluation was built in SolidWorks® using the morphology and dimensions of the left atrium adjacent structures. From this geometry, the …

Evaluation Of Human Umbilical Vein Endothelial Cells In Blood Vessel Mimics Through Changes In Gene Expression And Caspase Activity, Conor Charles Hedigan

Master's Theses

Blood vessel mimics (BVMs) are simple tissue engineered blood vessel constructs intended for preclinical testing of vascular devices. This thesis developed and implemented methods to characterize two of these components. The first aim of this thesis investigated the effect of cell culture duration and flow conditions on endothelial cell gene expression, especially regarding endothelial-to-mesenchymal transition (EndMT). A trend of decreased endothelial marker gene expression and increased mesenchymal marker gene expression would indicate EndMT. qPCR analysis revealed that increased cell culture duration did not result in EndMT, and in fact increased endothelial marker expression as cell culture duration increased. Disturbed flow …

Fracture Control Modeling With The Finite Element Method, Jorge A. Pluma Reyes

Master's Theses

This thesis investigates the feasibility and usability of the finite element method approach in the design of crack arresting devices. Current design and manufacturing practices are improving structures' susceptibility to fracture, in particular brittle fracture; however, cracks in structures are still observed within their lifespans due to severe unexpected service conditions, poor designs, or faulty manufacturing. Crack arrester systems can be added during service to prolong the longevity of structures with sub-critical or critical flaws. Fracture properties of different specific structures under specific services can be obtained experimentally, however, experiments are expensive and of high complexity. Alternatively, the finite element …

Development Of A Model And Imbalance Detection System For The Cal Poly Wind Turbine, Ryan Miki Takatsuka

Master's Theses

This thesis develops a model of the Cal Poly Wind Turbine that is used to determine if there is an imbalance in the turbine rotor. A theoretical model is derived to estimate the expected vibrations when there is an imbalance in the rotor. Vibration and acceleration data are collected from the turbine tower during operation to confirm the model is useful and accurate for determining imbalances in the turbine.

Digital signal processing techniques for analyzing the vibration data are explored and tested with simulation data. This includes frequency shifts, lock-in amplifiers, phase-locked loops, discrete Fourier transforms, and decimation filters. The …

Transmission Probability Of Embolic Debris Through The Aortic Arch And Daughter Vessels During A Transcatheter Aortic Valve Replacement Procedure, Jessica Lena Wirth

Master's Theses

Cerebral ischemia leading to an ischemic stroke is a possible complication of a transcatheter aortic valve replacement (TAVR) procedure. This is because embolic debris can become dislodged and travel through the aortic arch, where they either continue to the descending aorta and join the systemic circulation or travel into the cerebral vasculature through the three daughter vessels that branch off the top of the aortic arch. These three vessels are the brachiocephalic artery, the left subclavian artery, and the left common carotid artery. These three vessels lead either directly or indirectly to the cerebral vasculature, where the diameter of vessels …

Sidewalks To Nowhere: A Tool To Prioritize Pedestrian Improvements, Ho Yan Lai

Master's Theses

Walkability as a concept that captures the ability to walk from one place to another has multiple dimensions. Between traversability to being a proxy for better urban places, there are also numerous measurements of walkability that attempts to quantify certain or all aspects of walkability. It is, however, unclear, through a review of available literature, how these measurements of walkability relate to each other statistically. This methodology focuses on generating a framework for analysts to evaluate and prioritize pedestrian infrastructure. WalkScore™ (WS), HCM Pedestrian Level of Service (PLOS), Average Nodal Degree (AND), and Intersection Density are the four metrics selected …

In-Plane Cyclic Behavior Of A Steel Mesh Reinforced Cob Wall, Julia Fremuth Sargent

Master's Theses

This thesis presents the results from in-plane cyclic testing of a reinforced cob wall. Cob is an earthen building material composed of sand, clay, straw and water. Cob is typically constructed with no steel reinforcement; however, the California Building Code requires reinforcement in all buildings for resisting seismic forces. The purpose of this thesis is to provide additional technical data to integrate cob into the building code.

Test results are reported for a 7’ x 8’ x 14” wall with two layers of welded wire steel reinforcement constructed on a reinforced concrete foundation. In-plane cyclic loading was performed on the …

Compact Rake Boundary Layer Data System Module, Nathan Jeffry Hoyt

Master's Theses

This Thesis describes the design, assembly, programming, and evaluation of the BLDS-M-RAKE, the newest addition to the family of devices called the Boundary Layer Data System (BLDS). The BLDS-M-RAKE is a continuation of the BLDS-M series of devices, a modular approach with updated electronics for boundary layer measurements. The BLDS-M-RAKE records data from a number of sensors, intended to be routed to an array of probes, or rake. Through preliminary testing, a new flexible manifold design from molded silicone and the hardware used on the RFduino development boards from the BLDS-M proof-of-concept modules were validated for use in the final …

Liquidated Damages: An Analysis Of Their Use And Effectiveness, Alfredo N. Aragon

Construction Management

A construction company’s success and/or failure is dependent upon project completion with respect to time and budget. Failure to meet the contract completion date results in a loss of profit for owners and contractors alike. In order to help mitigate project delays, liquidated damage clauses have been included into construction contracts. Incorporating provisions within the construction contracts in the form of liquidated damages aims to help shift the financial burden when there is a failure to meet contractual obligations, hopefully offering quick compensation for delays. Unlike general or actual damages, liquidated damages are pre-defined and agreed upon prior to entering …

Evaluating Creative Choice In K-12 Computer Science Curriculum, Kirsten L. Mork

Master's Theses

Computer Science is an increasingly important topic in K-12 education. Ever since the "computing crisis" of the early 2000s, where enrollment in CS dropped by over half in a five year span, increasing research has gone into improving and broadening enrollment in CS courses. Research shows the importance of introducing CS at a young age and the need for more exposure for younger children and young adults alike in order to work towards equity in the field. While there are many reasons for disinterest in CS courses, studies found one reason young adults do not want to study CS is …

Cmos Design Of An 8-Bit 1ms/S Successive Approximation Register Adc, Ameya Vivekanand Ganguli

Master's Theses

Rapid evolution of integrated circuit technologies has paved a way to develop smaller and energy efficient biomedical devices which has put stringent requirements on data acquisition systems. These implantable devices are compact and have a very small footprint. Once implanted these devices need to rely on non-rechargeable batteries to sustain a life span of up to 10 years. Analog-to-digital converters (ADCs) are key components in these power limited systems. Therefore, development of ADCs with medium resolution (8-10 bits) and sampling rate (1 MHz) have been of great importance.

This thesis presents an 8-bit successive approximation register (SAR) ADC incorporating an …

Advanced Concrete Course For Cal Poly Construction Management Department, Dante N. Feliciano

Construction Management

This senior project provides a solution to the Construction Management Department at Cal Poly, San Luis Obispo whose curriculum lacks an individual Concrete course. With Concrete being one of the most used building material worldwide, this course will help immensely. The goal of this project is to fill the gap with an Advanced Concrete Course that is prepared and ready to be introduced to future students. The course has an emphasis on outside research learning – where the student gets to become the instructor. Carefully thought out and executed lecture materials are included in the course. Lecture slides give background …

Development Of A Topics Course For Construction Management, William Harrison Wygal

Construction Management

The Cal Poly Construction Management program has been proven to produce some of the most prepared graduates heading into new careers in every facet of the construction industry. Speaking with faculty member Tom Kommer, we have concluded that there is a need for an increased focus on construction risk management within the curriculum. In order to develop a course which would suitably educate Cal Poly Construction Management students in the topic of risk management, I performed a literary review during which I determined which risks are most prevalent within the construction industry and how firms in the construction industry manage …

Cej Ankle Support Report, Christine Prothe, James Baldwin, Erik Espinoza

Biomedical Engineering

This document provides information about an ankle support device designed to allow for ankle dorsiflexion and plantar flexion. In this document the product’s specifications, objectives and expectations are outlined. Included in this document is background information, stage gate process, prototype design development and considerations, and qualification requirements.

House Calls Mobile Virtual Stethoscope, Abigail Lindquist, Abigael Donohue, Trey Nahhas

Biomedical Engineering

The purpose of this scope of work is to outline the progress of the Virtual Stethoscope design and development project as sponsored by House Calls Mobile. This device looks to provide accessible at-home care for patients all over the country through the mobile phone stethoscope attachment. With the virtual stethoscope technology, patients will be able to perform high-quality, in-home observation of heart, stomach, and lung sounds to be transmitted to a physician in real time. Eliminating the need to travel to a doctor’s office encourages patients to perform more regular checkups, increasing their likelihood potentially of life-saving early diagnoses. This …

Sand Foot: A Prosthesis For Walking On Sand, Samantha A. Galicinao, John Dewing, Daniel Dugan Dotson, Christopher Urasaki

Biomedical Engineering

This critical design report describes the product development of a prosthesis for use on sand. Quality of Life Plus (QL+), a national non-profit organization aimed to develop prostheses for veterans and people with disabilities, introduced this project and its accompanying challenger, Sgt. Brady, to Cal Poly’s Interdisciplinary Senior Project class in September 2018. After consulting with Sgt. Brady and QL+ and performing extensive research, the Sand Foot team defined customer requirements and engineering specifications to meet these requirements. Comfortability, durability, and sandproof were key customer requirements. Several conceptual models were brainstormed and a final design was selected based on the …

Duocel Metal Foam Display Cases, Kate Goldsworthy, Katherina Prodanov, Benjamin Swanson, Syed Hasan

Mechanical Engineering

This Final Design Review (FDR) report outlines the senior design project that was conducted by a team of four mechanical engineering students at California Polytechnic State University-San Luis Obispo for ERG Materials and Aerospace Corporation. The goal of this project was to design displays that showcase the properties of ERG’s Duocel® foam at tradeshows and client meetings. To better understand the needs of our sponsor, the team researched Duocel®’s capabilities, related technologies, and relevant standards and regulations. With this information, we further defined the problem by creating a problem statement and a set of engineering specifications through a Quality Function …

Insulated Solar Electric Cooker With Phase Change Thermal Storage Medium, Justin Brett Unger, Nathan Robert Christler, Matthew Weeman, Marcus Edward Strutz

Mechanical Engineering

This final design review document outlines the senior design project carried out by a team of four mechanical engineering students at the California Polytechnic State University – San Luis Obispo under the sponsorship of Dr. Peter Schwartz of the Cal Poly Physics department. The aim of this project was to improve upon the design of previously developed Insulated Solar Electric Cookers (ISECs) by adding a thermal storage system to allow for quicker cook times and the ability to cook food at non-peak solar hours. The team’s goal was to develop a working prototype utilizing a phase change medium as the …

Framed Human Powered Vehicle Frame, Keyanna Brielle Henderson, Brendon Howard Morey, Kyra Noelle Schmidt, Austin Patrick Henry

Mechanical Engineering

The following is the Final Design Review (FDR) Report for Framed, a team tasked with designing and fabricating the frame of the 2018-2019 Cal Poly Human Powered Vehicle (HPV) Club bike. The bike is to be raced at the 2019 World Human Powered Speed Challenge in Battle Mountain, Nevada with the goal of breaking the American collegiate speed record. The purpose of the FDR Report is to introduce the project’s background and objectives, discuss the final design, and present the results of manufacturing and testing. Prior to beginning work on the design of the frame, the group conducted extensive research …

Vaccine Cooler For The Global Poor, Benjamin J. Larson, Cooper E. Gibson, Eilbron Younan, Cody R. Volk

Mechanical Engineering

Cal Poly physics professors Peter Schwartz and Nathan Heston approached the Solar Freeze team with the problem that remote communities in Africa have limited access to modern-day medicine or vaccines. They suggested that we try and design a cooling device that can keep vaccines cold for multiple days at a time while the medicine is transported to remote villages. Currently, there are vaccine cooler products on the market, but most of them are very expensive or lack portability. Peter and Nate have tasked the Solar Freeze team to come up with a less expensive solution that is also portable and …